WIRELESS ALARM SYSTEM WITH TELEPHONE AUTO DIALER

Our WIRELESS ALARM SYSTEM WITH TELEPHONE AUTO DIALER is designed to allow you to create your own security system. When the AUTO DIALER is connected to a telephone land line and an electrical outlet and set to ARM mode it will alert you when any of the sensors have been triggered. The auto-dialer will activate the built-in siren or chime (if set) and dial out (if set) to up to 5 pre-programmed telephone numbers with your own pre-recorded message. You can choose to remotely listen in & broadcast to the protected perimeter. Once you know the situation, you can take appropriate actions.

There are no monthly fees to pay!

www.idealalert.ca SK634

BAT.LOW AC

“THE SYSTEM THAT CALLS YOU!”

Thank you for choosing Ideal Security’s Home Security System with Telephone Auto Dialer. If you have any questions, problems or comments regarding the installation or operation of this system, please do not hesitate to contact IDEAL’s customer service department through our web site at www.idealalert.ca, via email at info@idealalert.ca, or by calling our toll free number at 800-361-2236 x 230. Normal business hours 7:30 AM to 3:00 PM Eastern time. Monday to Friday.Occasionally instructions have errors or omissions, please check for updates to these instructions, security tips and other valuable information at www.idealalert.ca

THIS PACKAGE INCLUDES: • 1AUTO-DIALER• 2REMOTECONTROLS• 2WINDOW/DOORCONTACTS

• 1MOTIONSENSOR• 1INDOOR/OUTDOORSIRENWITHLEDSTROBE• ALLBATTERIESANDAC/DCADAPTERS.

NOTE:BEFOREPERMANENTLYINSTALLINGANYOFTHEDEVICESINCLUDEDINTHISPACKAGEPLEASETEST THERANGEOFALLUNITSTOMAKESURETHATTHERECEIVERPICKSUPALLTHESENSORS.NOTE:THETELEPHONEDIALERREQUIRESANELECTRICALOUTLETANDATELEPHONELANDLINE WITHTONEDIALINGTOMAKEOUTGOINGCALLS.

SETUP OVERVIEW

• Setyourpasscode(refertoAUTO-DIALERSET-UPsection1)• Programtelephonenumbers(refertoAUTO-DIALERSET-UPsection4)• Recordyournotificationmessage(refertoAUTO-DIALERSET-UPsection2)• Installdoor/windowsensors(refertoINSTALLATIONOFSENSORSsection)• Installmotionsensor(refertoINSTALLATIONOFSENSORSsection)• Installindoor/outdoorsiren(refertoWIRELESSINDOOR/OUTDOORSIREN&STROBELIGHTsection)

It’s done! You can now activate the system and be protected with this simple, effective wireless security system with auto dialer.

NOTE: To change the default settings and expand the system, follow the detailed instructions provided in this manual.

IMPORTANT SAFETY TIPS

1. Do not install the system where it will be exposed to direct sunlight or rain. 2. The built-in siren is very loud, never put the system close to your ear. 3. The system should be installed away from heat sources such as radiators, heating ducts and stoves. 4.Ifthesystemsoundsatrandom,itispossiblethattheinstalledlocationistooclosetoaheatsource,changingthelocation

or direction of the unit may correct the problem. 5. The system can provide valuable protection for your home and property if utilized properly. However, this unit cannot

guarantee complete protection against burglary or property damage. Therefore, we will not be responsible for any losses or damages which may occur, while using this product.

ANSWERING MACHINES AND REMOTE COMMUNICATION

IfyouintendtousetheREMOTEACTIVATIONfeatures(controllingthealarmunitremotely)oftheAutoDialer,youcannotuse an answering machine.To use the remote activation feature: Set the auto dialer to respond (pick up) before your answering machine responds. For example, if your answering machine is set to pick up after 5 rings then set the auto dialer to pick up after 3 rings, this way yourAUTODIALERwillpickupfirst,allowingyoutoenteryourkeyselection.Completeinstructionsonsettinguptheremoteactivation follow.Iftheansweringmachineisrequired,thentheREMOTEACTIVATIONfeaturecannotbeused. Set the auto dialer to respond after your answering machine normally responds (set it to 10 rings) this will ensure that the answeringmachineisfirsttorespond.

TELEPHONE AUTO DIALER

DESCRIPTION OF COMPONENTS

1. Antenna Jack 2. Antenna 3. LCDDisplay4. VoiceSpeaker

5. REC./PlayLED6. BatteryLowLED7. Power LED 8. NumericKeypad

9. Microphone 10. To Wall Jack (LINE) 11. To Telephone (TEL.) 12. DC9VJack

13. BatteryCover14. ResetButton15. Siren speaker16. Wired Input Terminal*

FEATURES

• Receivessignalsfromwirelesssensors-activates Telephone auto-dialer and alarm

• Roommonitorbytelephonefunction• Programmablevoicemessagefortelephonealert• ARMorDISARMsystembytelephone• Programmablepassword• Entrydelaytiming(settimeforhowlongaftertriggerevent

before the auto dialer will dial out and siren will sound) • Upto5emergencytelephonenumbers(upto32digits

each)(onlylast16digitsappearonLCDscreen)• Programmableautodialingcycle(numberoftimesthe

auto dialer will dial each programmed phone number) up to 5 cycles

• Built-in105dBalarm(withprogrammablealarmon/off)• HOMEmodefunction(autodialerwillchimebutnotdial

out when sensors are triggered)

• 16Digit,largenumberdisplay• 10zoneiconsforeasydifferentiationofsensorlocations• Zones1-8:Canlinkonewirelesssensortoeachzone• Zone9:Canlinkupto8wirelesssensors• REMOTEzone:Canlinkupto8remotecontrols• Recordsthefivemostrecenttriggeredalarms• Built-inflashmemorytoprotectsystemdataduringa

power failure. If the battery dies, all info will remain in auto dialer except the date and time.

• BatteryLowindicator.Werecommendthatthebatteryin the dialer be changed at least once per year, as you change your smoke detector battery.

• Wiredsensorinputterminal(toconnectIdeal’swiredwindowanddoorcontactsSK619)

• ACadaptorand9Vbatteryback-up(included)• Wallmountable(screwsandanchorsincluded)

INSTALLATION

NOTE: The Dialer Unit must be installed where it has access to a land line and an electrical outlet.• Install9Vbatteryincluded(Fig1).Thebatteryinstalledinthisunitisaback-upbatteryonly.Thisbatterywillkeeptheunit

working for a limited time during a power failure. • Positiontheantennavertically(straightup)forbetterreception.(Fig.2)

• Connecttheincludedphonecordtothejackonthecontrolunitlabeled“LINE”.Connecttheotherendofthecordtoyour

walljack.(Fig.3a)NOTE:IfyouareusingaDSLservice,aDSLfiltermustbeinstaledbetweentheautodialerandthewalljack.• Aphonecanbeconnectedtotheunitusingthe“TEL.”jack.(Fig.3a)Checktoseeifyouhaveadialtone.• ConnecttheACadaptortotheDC9Vjackontheauto-dialer.(Fig.3b)

* For complete instructions on how to add wired components to the auto-dailer visit; www.idealalert.ca

OP

EN

121110

1514

13 16

TEL.LINE

( Fig. 3a )

TEL.LINE

( Fig. 3b )

TEL.LINE

DC 9V Adaptor

(TEL.)To telephone

(LINE)To wall socket

• Wallmountoption:Chooseasuitablelocationwhereyouhaveaccesstoatelephonelineandelectricaloutlet, drill holes using template provided and install anchors and screws. Place the auto-dialer over the screws and slide it down to secure it in place.

AUTO-DIALER SET-UPNOTE: If no key is pressed for 20 seconds, the auto-dialer will automatically exit set-up mode. • Set-upisdoneinDISARMmodeonly.• Theauto-dialerhasafactorypresetpasswordof0-0-0.Thisshouldbechangedtoyourownpersonalpassword.

1. TO CHANGE PASSWORD

• Enterfactorypre-setpassword0-0-0.PressPROGbuttononce(1),PASSWORDwillflashontheauto-dialerscreen.• PresstheARM/DISARMbuttontoconfirmthatyouwanttoenterthePASSWORD.• EnteryournewpasswordthenpresstheARM/DISARMbuttontoconfirmyourpasswordhasbeenstored

(you can choose from 3 to 6 digits for your password). • PressthePROGbuttonnine(9)timestoexitset-upmode.NOTE: PASSWORD RESET Ifyouforgetyourpassword,locatetheRESETbuttononthebackoftheunit.PressandholdthePROGbutton,and,pressandreleasetheresetbuttononce.Thescreenwillgoblank.WhenscreenreturnsletgoofthePROGbutton.Younowhavethe factory pre-set password of 0-0-0. This will reset the password ONLY, all other information will remain (programmed telephone numbers and learned sensors).

2. RECORD PERSONALIZED NOTIFICATION MESSAGE

Youcanrecordasinglepersonalized20secondmessagethatwillbeplayedbackwhenyoureceivetelephonenotificationthat your system has been triggered. To help remember the options you have, your message should be similar to: “[Your name’s] security system has been triggered, please enter a command; to Monitor Room press 1 and #, to Broadcast press 2 and #, to End Call press 3 and #, to Disarm System and end call press 6 and #”.

• EnterpasswordthenpressREC/PLAYonce.• Clearlyandslowlydictateyour20secondmessage.• PressREC/PLAYtoendrecording.Therecordingwillautomaticallyendafter20seconds.Themessagewillreplayonce

afterrecordingisfinished.• PressREC/PLAYtoreplaymessageatanytime.

3. SETTING THE TIME (YEAR / MONTH / DATE / HOUR / MINUTES)

• EnterpasswordthenpressthePROGbuttonnine(9)times.• Willflashontheauto-dialerscreen.• PressARM/DISARMbuttontoconfirm.• Thedatewillshowontheauto-dialerscreenasfivesetsofnumbers:year,month,anddatefollowedbythetimehourand

minutes(24hr.timeclock).Thefirstsetofnumberswillflashconfirmingthatthesecannowbechanged.• Entercorrectyearbypressing*/UPor#/DOWNbutton,thenpresstheARM/DISARMbutton.Thenextsetofnumberswill

startflashing,enterthemonthbypressing*/UPor#/DOWNbutton,thenpresstheARM/DISARMbutton.Continueuntilyou have the correct date and time.

• PressPROGbuttononce(1)toexitset-upmode.

4. TO PROGRAM EMERGENCY TELEPHONE CALL NUMBERS

• EnterpasswordfollowedbyPROGbuttontwice(2).• MEMORYwillflashontheauto-dialerscreen.

• PressARM/DISARMbuttontoconfirm.• Youarenowreadytoprogramupto5emergencytelephonenumbers.Pressthe*/UPor#/DOWNbuttonstoselect

memory location from 1 to 5. If you select 2 this is where your number will be stored and it will be the 2nd number dialed. • Enterthetelephonenumberyouwouldliketostore,asyouwouldnormallydialitinyourarea(maximumof32digits,the

screenwillonlydisplaythelast16digits),followedbyARM/DISARMtoconfirm.• Repeatstepsforthefourothernumbersyoumaywishtostore.• DONOTuse911asonofthestoredtelephonenumbers.• PressPROGbuttoneight(8)timestoexittheset-upmode.

5. TO DELETE A TELEPHONE NUMBER FROM MEMORY

• EnterpasswordfollowedbyPROGbuttontwice(2).• “MEMORY”willflashontheauto-dialerscreen.• PressARM/DISARMbuttontoconfirm.• Press*/UPor#/DOWNbuttonstoselectthenumberyouwanttodelete.• PressDEL./PAUSEbuttontodeletethenumber.• PresstheARM/DISARMbuttontoconfirm.• PressPROGbuttoneight(8)timestoexittheset-upmode.

6. PAUSE FUNCTION

The“PAUSE”functioncanbestoredasonedigitinthetelephonenumbermemoryforsomedialingoperations.EveryonePAUSE in the memory dialing sequence will pause for 3.6 seconds. For example, if you want to store telephone number 514-363-1030EXTENSION230tomemorylocation2,theoperationwillbeasfollowing:• EnterpasswordthenpressPROGbuttontwice(2).• “MEMORY”willflashontheauto-dialerscreen.• PressARM/DISARMbuttontoconfirm.• Press*/UPor#/DOWNbuttontoselectmemorylocation2.• Enter5143631030pressandholdDEL./PAUSEfor2secondsuntiltheletterFappearsonthescreen,thenenter230.• PressARM/DISARMbuttontoconfirm.• PressPROGbuttoneight(8)timestoexitset-upmode.

7. TO PROGRAM AUTO CALL FUNCTION ON/OFF

The auto-dialer has been factory pre-set with the call option ON. If you do not want the auto dialer to call out change this to OFF:• EnterpasswordfollowedbyPROGbuttonfive(5)times.• The“ ”iconwillflashontheauto-dialerscreen.• PressARM/DISARMbuttontoconfirm.• Using*/UPor#/DOWNbuttonstoselectcallOFFfollowedbytheARM/DISARMbuttontoconfirm.• PressPROGbuttonfive(5)timestoexittheset-upmode.

8. TO PROGRAM AUTO DIALING CYCLE (how many times the auto dialer will call the programed numbers).

The auto-dialer has been factory pre-set to auto dial for 1 cycle (When a sensor is triggered the auto dialer will call all stored numbers 1 time). You can change the number of cycles from 1 to 5 dialing cycles. • EnterpasswordfollowedbyPROGbuttonsix(6)times.• “CYCLE”willflashontheauto-dialerscreen.• PressARM/DISARMbuttontoconfirm.• Using*/UPand#/DOWNbuttonstoselectnumberofcyclesbetween1and5followed

bytheARM/DISARMbuttontoconfirm.• PressPROGbuttonfour(4)timestoexitsetupmode.

9. TO TEST MEMORY DIALING

Instandbymode,pressandholdthePROGbuttonforatleast3seconds,youwillhearashortbeep.Keyinthememorylocationofthetelephonenumber,i.e.1–5.Thetelephonenumberstoredinspecifiedmemorylocationwillautomaticallybedialed.PressthePROGbuttontostopthedialing.Theautodialermustbeconnectedtoalandlineinorderforthisfunctiontowork.Ifnotconnectedthenyouwillhear4shortbeeps.

10. TO PROGRAM CALL-IN RING DETECT CYCLE (how many rings before auto dialer will answer).

The auto dialer has been factory preset to answer after the 5th ring. The call-in ring detect cycle is for how many times you wantthephonetoringbeforetheauto-dialerpicksup.Youcanarm/disarmandmonitoryourhomeviathetelephone.• EnterthepasswordfollowedbythePROGbuttonseven(7)times.• The“ ”symbolwillflashonthescreen.• PressARM/DISARMbuttontoconfirm.• Usingthe*/UPand#/DOWNbuttonsselect3,5,7or10(whichrepresentsthe#ofringsbeforetheautodialerpicksup)

followedbytheARM/DISARMbuttontoconfirm.• PressthePROGbuttonthree(3)timestoexitset-upmode.NOTE: You cannot use an answering machine with this feature. If you want to be able to call in to the auto dialer you must programittoanswerbeforeyouransweringmachinedoes.Exampleifyouransweringmachineanswersafter4rings, you must set the auto dialer to answer at 3 rings.

11. TO PROGRAM INTERNAL 105 dB AUTO DIALER SIREN ON/OFF

The auto-dialer has been factory pre-set with the siren ON. To change this to OFF:• EnterpasswordfollowedbyPROGbuttonfour(4)times.• The“ ”iconwillflashontheauto-dialerscreen.(Fig.8)• PressARM/DISARM toconfirm.• Using*/UPor#/DOWNbuttonstoselectSOUNDOFF.• PressARM/DISARMbuttontoconfirm.• PressPROGbuttonsix(6)timestoexittheset-upmode.

12. TO PROGRAM ENTRY DELAY TIME: (Time allowed to deactivate system once you have entered your residence)

The auto-dialer has been factory pre-set with a 20 second delay. To change the delay time to 0, 5, 10, 15 or 20 seconds:• EnterpasswordfollowedbyPROGbuttoneight(8)times.• “ENTRY”willflashontheauto-dialerscreen.• PresstheARM/DISARMbuttontoconfirm.• Usingthe*/UPand#/DOWNbuttonsselecttheseconds0,5,10,15or20• PressARM/DISARM toconfirmthenumberofsecondsyourequirefortheentrydelaytime.• PressthePROGbuttontwice(2)toexitset-upmode.

INSTALLATION OF SENSORS BeforeinstallingSensorspermanentlyyoushouldtestthesignalrange.Transmissiondistancefromsensorstothe auto-dialer is approximaly 60 meters (200’). Using HOME MODE is a convenient way to test Sensors and Remotes. In HOME MODE the auto-dialer will function only as a chime. Press the HOME button on the keypad of the auto- dialer, wait 60 seconds at which time you will hear a beep. Then trigger the wireless sensors. The auto-dialer will receive a signal and a chimewillsound.Ifyoudonothearachimeandthezoneisnotflashingontheauto-dialerscreen,thesensormaybeoutofrange.Repositioningeitherthesensororauto-dialershouldfixthisproblem.PressHOMEbuttonagaintoexittestmode.

MOTION SENSOR

Description of Components

1

2

34

1. Mounting bracket 2. Motion sensor window3. Batterylow/TriggerLED4. Batterycompartment

Installation

(Fig. 4)• Install9Vbattery(included)intothemotionsensor(Fig.4).• Themotionsensorisfactorylinkedtozone1.Whentriggeredzone1will

flashontheautodialerscreen.

• Themaximumdetectionrange(lefttoright)is110degreesforamaximumdistanceupto8m(26'). • Testthearearequiringcoveragebeforemountingthesensorpermanently.• TheLEDonthefrontoftheunitwillflashcontinuouslywhenmotionissensed.• Usetheswivelwallmountbrackettomarkthemountinglocation,drillholesandinstallanchorsandattachthebracket

withthescrewsprovided.Slidethemainunitontothebracketuntilitclicksintoplace(Fig5).Adjustthebrackettoobtainthe best coverage of the intended protected area (Fig 6).

1.5~2m(5’~6’)

5~8m (16~26’)

110°

(Fig. 6)

(Fig. 5)

BATTERY LOW INDICATOR

Whenthebatteryislow,theLEDonthefrontoftheunitwillflashon3secondsandoff1second.Replacethebattery immediatelytomaintainproperdetection.Ifbatteriesarelowtheymaysendafalsesignaltotheauto-dialer.Batteriesinallunits should be replaced at least once per year.

DOOR/WINDOW SENSORS WITH VIBRATION DETECTION

1

2

3

4 5

67

8

Description of Components

1. Trigger/batterylowLED 5. Magneticcontact2. Alarm speaker 6. Alignment arrows3. Antenna 7. AlarmON/OFFswitch4. Wiredcontact 8. Batterycompartment

Installation

• Installthe9Vbattery(included)intothetwodoorandwindowsensors(Fig.7).

(Fig. 7)

• Thesetwosensorsarefactorylinkedtozone2and3.Whenoneofthesensors istriggeredeitherzone2orzone3willflashonthescreen.

• TheLEDonthefrontoftheunitwillflashcontinuouslywhenthecontactsareopen.• Determineappropriatelocationforthecontactsonthedoororwindowtobeprotected.• Mountthewiredportionofthecontacttothedoororwindowframeandthe

magnetic contact portion to the door or window. • Formaximumvibrationdetectionthesensorshouldbemountedonorasclosetotheframeofthedoororwindowas

possible.Beforeusingthedoublesidedtapeprovided,alignthe2sensorportionssothattheyareflushandwiththealign-mentarrowsfacingeachotherandnomorethen1/4" apart. Make sure to extend the antenna on the sensor for the best transmission range.

• TheDoor/WindowSensorshavebuilt-in105dBalarmswhichwillsoundforone10secondburstwhenthecontacts haveseparatedorthedetectorsensesvibration.ThisfeaturecanbecontrolledwiththeALARMON/OFFswitch on the side of the unit.

BATTERY LOW INDICATOR

Whenbatteriesarelow,theLEDonthefrontoftheunitwillflashon3secondsandoff1second.Replacethebatteriesimmediatelytomaintainproperdetection.Ifbatteriesarelowtheymaysendafalsesignaltotheauto-dialer.Batteriesinallunits should be replaced at least once per year.

WIRELESS INDOOR/OUTDOOR SIREN & STROBE LIGHTDescription of Components

10

2

3

4

1

BAT.LOW AC

LEARN

DC 6V56

8

97 ALKALINE

RECHARGE

10S

0S

1. Antenna2.Arm/Batterylow/TriggerindicationLED(red)3. Strobe light4.ACindicationLED(green)5.Siren/Lightfunctionswitch6. LEARN button7.Alkaline/Rechargeswitch8.DCJack9. Entry delay switch10.BatterycoverInstallation

• Removethescrewsfromthebatterycompartmentcover(Fig.8).

AAA

AAA

AAA

AAA

ALKALINE

RECHARGE

10S

0S

(Fig. 8)

• SettheEntrydelay(0/10seconds)timerswitch.• Setthebatterytypeswitch.

WARNING:Failuretochoosethecorrectsettingwilldamagethisunit. IfyouusenonrechargeablebatteriestheswitchmustsettoALKALINE. IfyouuserechargeablebatteriestheswitchmustbesettoRECHARGE. NOTE:UNITWILLNOTRECHARGEBATTERIES.

• Install4AAAbatteries(included),or4AAA700mAhNI-MHrechargeable batteries(notincluded).BatteriesprovideBack-uppowerforemergency functionality in case of power failure.

ALKALINE

RECHARGE

10S

0S (Fig. 9)

• SettheSiren/Lightfunctionswitch. • Temporarilyremovethewaterresistantrubbercovertoselectthealarmfunction.

Settheswitchto:Sirenonly/Siren+Strobelight/Strobelightonly.Replacecover.• PlugtheACadaptortotheDC6Vjack.TheACpowerindication

LED will show a steady light (Fig. 9).• TheSirenincludedwiththiskitisfactorylinkedtotheAutoDialer.• Normaltransmisionrangeisbetween40-60meters(130’-200’)• Mountinashelteredareaprotectedfromtheelements.

WIRELESS REMOTE CONTROLS Description of Components

12

3 4

1. Panic button2. DisarmButton3. Arm button4. Batterycompartment

Installation

InstalltheCR2032batteryincludedintotheremotecontrol(Fig.10).

(Fig. 10)

• RemotecontrolsforArm,DisarmfunctionsoftheTelephoneDialer.• Remoterangefromreceiverisupto25meters(80feet).• TheRemoteControlsincludedwiththiskitarefactorylinkedtotheautodialer.If the remote has to be moved closer to the receiver in order to function please replace batteries. The battery life is about six months under normal use.

NOTE: If you wish to change the factory programed zone location of the sensors see: LINK WIRELESS SENSORS TO THE AUTO DIALER.

SYSTEM OPERATION1. TO ARM THE SYSTEM

• EnterpasswordfollowedbytheARM/DISARMbuttonorpresstheARMbuttonontheremotecontrol.• ThreeshortbeepswillsoundandtheARMiconwillshowontheauto-dialerscreen.• Wait60secondsforashortbeep.Theauto-dialerisnowsetatARMandreadytoreceivesignals.• IfanOPENZONEconditionexists(adoororwindowisopen)theautodialerwillbeepfor5secondsandthescreenwill

show“CLOSEPLEASE”andthezonenumberofthesensorthattriggeredthealarmwillbeflashing.Ifthezoneremainsopen (the door or window is not closed) after 60 seconds the alarm will sound and the auto dialer will start dialing.

2. ALARM OPTIONS

• Iftheauto-dialer(inARMmode)receivesasignalfromanysensor,thescreenwilldisplayTRIGGERwiththezonenumber. After the entry time delay it will sound a SIREN for 30 seconds on, 30 seconds off and 30 seconds on, and will automatically dial all the numbers stored, one by one, for the number of cycles (amount of times the numbers are dialed) you have chosen. The receiver of the phone call will hear a prerecorded message and will have option to listen in or broad cast to the room the auto-dialer is located in. The receiver of the call can then take appropriate action.

• InARMmode,iftheauto-dialerissettoSIRENOFF,thenumbersstoredwillbedialedsilently.Nosirenwillbeheardfromtheauto-dialer.NOTE:TheINDOOR/OUTDOORSIRENmustalsobesettoOFFforsilentoperation.

3. TO DISARM THE SYSTEM FROM THE AUTO DIALER KEY PAD

• EnterpasswordfollowedbytheARM/DISARMbuttonontheautodialer.OrpressonDISARMbuttonontheremote.• YouwillhearonebeepandtheARMiconwilldisappearfromtheauto-dialerscreentoconfirmthattheAuto-Dialerhas

been disarmed.• Beforedialingtheautodialerwilldetectifaphonelineisconnected,ifnotelephonelineisconnectedtheautodialerwill

beep4timesandthealarmwillsoundwithoutdialing.

4. PANIC BUTTON

• Ifyoupress“PANIC” buttononauto-dialerorremotecontrol,theALARMwillsoundinstantlyfor30seconds,thenofffor30 seconds, then on for 30 seconds and then off, and the auto-dialer will begin dialing the stored numbers immediately.

• Tostopthealarmsoundandthedialing,enterpasswordthenpressARM/DISARMbuttonorpresstheDISARMbutton on the remote.

5. REMOTE OPERATION BY TELEPHONE. (What you can do when you receive a call from the system)

Answer the call. You will hear your personalized message. The message will repeat 3 times. If no function codes are entered by the receiver of the call, the system will hang up and dial the next number programed. Youmayenterthefollowingcodesonyourphonekeypad.Onceacodeisenteredyouwillhearabeepforconfirmation. Function Press Keys

RoomMonitor 1and# Broadcasttoroom 2and# EndofCall 3and# DISARMSystem 6and#

6. REMOTE ACTIVATION BY TELEPHONE (To control your auto dialer via telephone)

• Usingaseperatetelephonelinedialyourhometelephonenumber.• Theauto-dialerwillanswerafterthesetamountofringsthatyouprogrammed.• OnceconnectedenteryourPASSWORD,youwillheartwobeeps(confirmation).• Enterkeycombinationlistedbelowfordesiredfunctionyouwouldliketoperform.ROOMMONITOR–Enter“1and#”afterthebeepyouwillbeabletolistenintotheroomwheretheauto-dialerisinstalled.After 30 seconds you will hear a beep to remind you that if you do not enter another code within 20 seconds the call will end. The total duration of the room monitor is 50 seconds if no other codes are entered. BROADCASTTOROOM–Enter“2and#”afterthebeepyouwillbeabletobroadcastintotheroomwheretheauto-dialerisinstalled. After 30 seconds you will hear a beep to remind you that if you do not enter another code within 20 seconds the call will end. The total broadcast time is 50 seconds if no other codes are entered.

ARMSYSTEM–Enter“5and#”afterthreeshortbeepsthesystemisARMEDandwillautomaticallyhangup.Ifyouhear5 rapid beeps after three short beeps, it means one of your sensors isn’t closed or is activated. The system will give you 5 seconds to enter a new code. DISARMSYSTEM–Enter“6and#”afterabeeptheauto-dialerwillDISARMandhangup.NOTE: Whether you receive an alarm call or you call the auto dialer, if you enter a wrong password or operation code, the call will disconnect and sound 5 beeps on the auto-dialer. If the call was an alarm call to you, you can wait for it to call you again (providing you have set the dialing sequence to more than one cycle) and then enter the above codes again. If your dialing sequence is set to one cycle and you have set up the auto dialer to answer before your answering machine (if you have one connected) then you can call into the auto dialer and enter in your codes again. If you made the initial call to the dialer you justhavetoredialandthenenterthecodesagain.

7. HOME MODE FUNCTION:

While at home you can set your auto-dialer to Home mode. This will activate a chime every time one of the sensors is triggered. You can also program which zone will send signals to the auto-dialer when triggered. The factory default is ALL sensors send signals to the auto dialer. To activate Home Mode.

• PresstheHOMEbuttononce;youwillhearachimeandthewordHOMEwillappearontheLCDscreen.• Wait60seconds,youwillhearabeep.Systemisnowinhomemodeandwillchimeifasensoristriggered.• Whenauto-dialerreceivessignalitwillchimeandshowwhichzoneisbeingtriggeredontheauto-dialerLCDscreen.If

thePANICbuttonispressedtheautodialerwillstartdialingthenumbersprogrammedfortheamountoftimesspecified.• PresstheHOMEbuttonagaintoexitthehomemode.NOTE: Arming system while in Home mode will deactivate Home mode. Press the HOME button again if you want to return to home mode. In home mode the system will not dial out or sound alarm. PressingthePANICbuttononthekeypadorremotecontrolwilltriggerthealarmandstartthedialingsequence.Enabling and Disabling sensors when in home mode.

When in HOME mode all sensors will send signal to auto dialer and you will hear a chime. If you have one or more sensors that you do not wish to activate a chime on the auto dialer you may disable the zone containing the sensor. For example, a contactonapatiodoorthatisinzone3,ifyoudisablezone3achimewillnotsoundeachtimethedoorisopened.Zone’s1through8control1sensorperzoneallowingforindividualcontrolof8sensors.Zone9cancontainupto8sensorsallsensors in that zone are enabled or disabled together, you cannot pick individual sensors in that zone. The REMOTE zone cannot be disabled. The factory preset is all sensors are on and will activate a chime when triggered. To turn off a zone:.• EnterpasswordfollowedbypressingtheHomebutton.• ZoneonewillflashontheLEDscreen.• Usingthe*/UPand#/DOWNbuttonsselectthezoneyouwanttochangethesettingfor.• PressARM/DISARMbuttontoconfirm,usingthe*/UP&#/DOWNbuttonsselectONorOFF.PressARM/DISARM

buttontoconfirm• PresstheHomebuttononcetoexithome-setup.

8. VIEW STORED INFORMATION FUNCTION

Triggered Events History

The last 5 triggered Events, including the time the event occurred and the zone that was triggered are stored in memory.To view triggered events: • Instandbymode,press#/DOWN button• ThetimeandzoneofthefirstrecordedtriggeredeventwillbedisplayedontheLEDscreen.• Pressingthe#/DOWNbuttonrepeatedlywillcyclethrough5storedeventsendingwiththemostrecent.Stored Telephone Numbers

Instandbymode,press*/UPtoviewstoredtelephonenumbers.NOTE: If no buttons are pressed for 20 seconds, the auto-dialer will automatically exit view mode.

9. BATTERY LOW LED INDICATOR

WhentheBatteryLowLEDflashesonceevery1.5seconds,itindicatesthatthebatterypowerinauto-dialerisrunninglow.Replace the batteries immediately. If batteries are low, a false signal may be triggered and the auto dialer may start dialing. Batteriesinallunitsshouldbereplacedatleastonceayear.

LINK WIRELESS SENSORS TO THE AUTO DIALER All the units included in this package have been factory linked to the auto dialer. You may link additional sensors, remote controls or sirens to your auto-dialer. In certain circumstances you may have to re-link existing parts.Make sure to test the reception range of all sensors before permanently mounting them. The approximate range for sensors includedwiththiskitis60meters(200′).Wallsandotherobstructionsmayinterferewithreception.You can link a total of 16 sensors and 8 remote controls to the auto-dialer . The system has a total of 10 zones for wireless sensors and remote controls:• Zone1-8:linkonewirelesssensorperzone,theywilltriggertheauto-dialerinarmedmodeonly.• Zone9:Learnupto8wirelesssensorsandtheywilltriggertheauto-dialerinarmedmodeonly.• REMOTEZone(LCDiconREMOTE)istheremotecontrolzone,youcanlinkupto8remotecontrols..NOTE: If you wish to change the factory programed zone location of the sensors they must be deleted from their current zone and re linked to a new zone (see instructions below)

LINKING WIRELESS SENSORS OR REMOTE CONTROLS TO THE AUTO DIALER

• EnteryourpasswordandpressthePROGbuttonthree(3)times.• The“LEARN”iconwillflashonthescreen.• PressARM/DISARM toconfirm,thesystemwillgointolearningIDcodemodeandzone1iconwillflash.• Pressthe*/UPand#/DOWNbuttonstoselectthezoneyouwishtolearnyoursensorto.WhenthescreenflashesNOID

CODE,thatmeansthatzoneisemptyandyoucanlinkasensor.IfthescreenflashesFULLthenyoualreadyhavea sensorlinkedtothatzone.YoucaneitherchooseanotherzoneorpressDEL./PAUSEtodeletethesensorinthatzoneand link the new sensor. Remote controls must be linked to the REMOTE zone.

• PressARM/DISARM toconfirmthatthisisthezoneyouwantthesensortobelinkedwith• Triggerthesensororremotecontrolthatyouaretryingtolinkasfollows: • WirelessmotiondetectorSK615,bymovinghandinfrontofsensortosendsignal(pleaseseenotebelow). • Wirelessdoor/windowsensorSK621&SK625,openingandclosingthemagneticswitchwillsendsignal. • WirelesswateralarmsensorSK616,putsensorinwatertotriggerandsendsignal. • WirelesstemperaturesensorSK627,bypressingthetestbutton. • GarageAlertSK623,openingthegaragedoorwilltriggerandsendsignal. • RemotecontrolSK629,pressinganykeywilltriggerandsendasignal.• Youwillhearalongbeepfromtheauto-dialertoconfirmthatlinkingwassuccessfulandthescreenwilldisplayFULLfor

zones1-8.Zone9willdisplaythenumberofsensorsinthezoneuptoamaximumof8.TheRemotezonewilldisplaythenumber of remote controls in the zone up to a maximum of 8.

• PressthePROGbuttonseven(7)timestoexitthesetupmode.NOTE: if you have linked a motion detector to your auto dialer, cover the lens of the motion sensor (place a towel over the sensor) before linking other items as the motion sensor will send a signal to auto- dialer every time you move.

LINK THE AUTO DIALER TO THE INDOOR/ OUTDOOR SIREN

The Siren included in this package has been factory linked to the auto dialer. Make sure to test the reception range of the siren before permanently mounting it. The approximate range for the indoor/outdoorsirenincludedwiththiskitis40meters(130′).Wallsandotherobstructionsmayinterferewithreception.To re-link the auto-dialer to the siren:• RemovethewaterresistantrubbercaponthebottomoftheSiren,pressandholdtheLEARNbutton,releasethebutton

afterhearingasingleconfirming“beep”,theunitisnowreadytolinkwiththeAutoDialer• OntheautodialerpressthePANICbutton.• YouwillhearalongbeeptonefromtheSirentoconfirmlinkingwassuccessful.Iflinkingwasunsuccessfulyouwillhear

fourshortbeeps.Carefullyrepeatthesteps.• TounlinkallautoDialers,SensorsorRemoteControlsfromtheSiren:pressandholdLEARNbuttonfor12seconds,you

will hear a long beep tone, all links will be deleted.

TROUBLE SHOOTING GUIDE AUTO-DIALER WILL NOT ARM/DISARM USING THE KEYPAD

• Makesureyouhaveenteredthecorrectpassword,ifnot,re-enterthepassword.• Ifitstilldoesnotwork,performthepasswordresetfollowingtheinstructionsinthe“CHANGEPASSWORD”sectionto

reset the auto-dialer. • RetrytheARM/DISARMfunction.

AUTO-DIALER WILL NOT DIAL

• Makesurethetelephonelineisconnectedproperly.• Makesurethetelephonenumbersarestoredcorrectly.• Makesuretheauto-dialerissetupforauto-dialmode.• Ifauto-dialerdoesnotreceiveasignalfromthewirelesssensor,re-linkthesensortothedialerfollowingtheinstructions

inthe“LINKINGWIRELESSSENSORSTOTHEAUTODIALER”section.

FALSE TRIGGERS

If sensors send false signals, • Ensurethatthebatteriesarestillingoodoperatingcondition.• Makesurethatthegapsbetweenthecontactandsensoronthewindowanddoorcontactsarenomorethana1⁄4”apart

and that arrows are pointing towards each other. • Itispossiblethattheinstalledlocationistooclosetoaheatsource,changingthelocationordirectionoftheunitmay

correct the problem.

TIPS

• DONOTprogram911tothedialingsequenceoftheauto-dialer.• Makesurefulltelephonenumbershavebeenenteredcorrectly.• Onlysuitableforsinglephoneline.Notcompatiblewithfaxmachinesormultilinetelephones.• AutoDialerrequiresalandlineandtonedialing

WARNING

All batteries including the back up battery in the telephone dialer should be changed at minimum once per year as the battery in smoke detector is changed. Should a power failure occur and the back up battery is weak, or batteries in any of the sen-sors are weak, false alarms may occur. If the telephone dialer or any other detector is not being used for an extended period, remove the batteries to avoid any damage from battery leakage.

CUSTOMER SERVICE

Thank you for your purchase: Wearededicatedtocustomerserviceandwillworktoresolveanydifficultiestoensurecustomersatisfaction.Ifyouhaveanyquestions about the setup or function of this product, please call us before returning this product to the point of purchase. Our customer service number is: 1 800-361-2236 EXT. 230(514-363-1030EXT.230localMontrealarea)

NOTE: Please preserve this manual. It contains valuable information for properly setting up and operating the system. Please check for updated instructions at www.idealalert.ca

WARRANTY: 1 year limited warranty (excluding batteries) on components.

Ideal Security Inc. www.idealalert.ca e-mail: info@idealalert.ca Tel.: 1 800-361-2236 EXT. 230