WALCHAND COLLEGE OF ENGINEERING, SANGLI · WALCHAND COLLEGE OF ENGINEERING, SANGLI ... 8085 Microprocessor trainer kits: ... Cable set and Power supply/SMPS. 25 11. Interfacing Kits:

Tender November 2011

Page 1 / 36 Seal and Signature of Bidder

WALCHAND COLLEGE OF ENGINEERING, SANGLI

TENDER DOCUMENT

(A)Tender for supplying equipments to various departments (B) Tender for supplying Answer books to Exam. Cell

Date of Prebid Meeting – 1st November, 2011 at 12 Noon

LAST DATE OF RECEIVING 11th Nov, 2011 up to 2:00 pm

DATE OF OPENING THE TENDER 11th November, 2011 at 3.00 pm

In Conference Hall, Main Building

Cost of the Tender Form: Rs. 1,000/- only



INVITATION FOR TENDERS UU

Ref No; - WCE/CS/ Date: - 14/10/2011 To ___________________________________ ___________________________________ Dear Sir, Sub: Invitation of Tender for supply of Equipments for various departments

You are invited to submit your most competitive tender for supply of Equipments for various departments under the terms and conditions as enclosed herewith.

This tender form is also available on college website www.walchandsangli.ac.in While submitting the Tender, the offer must be submitted in following fashion.

1. Two separate envelopes are to be used. 2. First envelope should be titled as “Specifications Envelope” and it should contain documents such

as: i) Shop Act license ii) I-Tax Return iii) Experience certificate iv) Sales Tax Registration v) Authorized dealer / distributor certificate vi)Proprietary item certificate , if applicable, viii) Copy of the receipt for Rs 1000/- for purchase of the tender form from the college office OR D.D. for Rs 1000/- if the tender form is down loaded from the college web site (for cost of tender form which is non refundable & without which tender will not be considered), viii) Separate (not a single) E.M.D. D.D.s for each of the department as per page number 36/36. All of the above D.D.s must be drawn from nationalized bank, favoring “The Director, Walchand College of Engineering, Sangli” payable at Sangli, ix) Detailed Specification of the offered item (if it differs from what is indicated in the tender) as per the tender form, but with no indication of offered cost of the respective item. Pages marked as 35/36, 36/36 must be signed and rubber stamped. This envelope must be sealed. At the time of tender opening, if the specifications and the other documents in this envelope are found correct, second envelope will be opened, otherwise the tender submission is likely to be rejected. The tender form is not transferable. Each bidder shall submit only one tender.

3. Second envelope should be titled as “Commercial Offer Envelope” and it must be sealed. Your “Commercial Offer” sealed envelope should contain competitive offered prices for the items. Taxes for VAT and other if any (except Octroi) should be clearly indicated in the column “Total Amount”. Octroi is to be paid at actual by the tenderer, while supplying items. The octroi receipt must be in the name of the Director, Walchand College of Engineering Sangli. Separate envelopes (and not a single envelope) are to be used for each of the departments. All the department specific pages of the tender form should be filled with the competitive prices offered, signed and rubber stamped on each page. The other specifications of the item, its make and model number, its detailed other features, leaflet of the items, customer list along with their contact details (where the tenderer has earlier supplied the item) etc., must be supplied in the department specific envelopes. If the space provided in the tender form is insufficient, additional pages may be attached appropriately.

4. Two of the separate sealed envelopes, namely, “Specification Envelope” and “Commercial Offer Envelope” must be sealed together in a “common” single envelope.

5. Each of these envelopes should be also titled, as per the case for either “Supply of Equipments for various departments “or “Supply of Roof Sheets to Mechanical Department” or “Supply of Answer Books to Exam Cell” only. Tenderer must also mention their Company name, Address, email, contact person, cell no. etc. on envelopes.

6. If tenderer has SSI registration, the tenderer will be exempted from paying E.M.D. The valid SSI registration documents, for this purpose, must be enclosed in “Specifications Envelope”.



7. If the tenderer is selected for supply of items, the selected tenderer will give an undertaking for

supply of items as per the college’s terms and conditions, and the tenderer will supply the items accordingly. If the tenderer fails to supply the items as per college’s terms and conditions, the EMD amount of the tenderer will not be returned. EMD will be returned to all other “not selected” tenderers only when the selected tenderer supplies all the items as per college’s terms and conditions. The selected tenderer has to submit Bank guarantee for 10 % of total purchase value. The Bank Guarantee will be returned, if no violation of terms and conditions are found, only at the end of the warranty period or at the end of contract to the tenderer.

The supply place is normally respective departments of college and supply period is usually 15 days

from the date of placing order. We look forward to receive your tender and thank you for your interest in this system.

yours faithfully,

Director Walchand College of engineering, Vishrambag, Sangli

Tender September 2011


(A) Equipments : (1) Computer Science & Engineering Department:

Item No. Particulars Approx.

Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.

EMD amount (3 % of the

total amount)

q a b (q*a)+b 1

Branded Desktop Computer System (without monitor): Dell / HP / HCL/ ACER / LENOVO

• Intel ® Core™ i7-2600 (3.40 GHz, 8MB) or higher with latest configuration

• 2GB (1x2GB) NECC DDR3 1333MHz SDRAM Memory expandable upto 16GB or higher

• 320GB/500GB SATA @ 7200 RPM Hard-disk Drive • No FDD • 16X SATA DVD+/-RW or higher, • Internal Business Audio Speaker • Intel®Q57 Express Chipset or higher, Intel® Graphic Media HD • Integrated 10/100/1000 Ethernet (Intel WG82576 or higher); • USB Entry Keyboard, Optical USB Mouse • DOS Factory Installed (English) • 10-12 USB 2.0 ports,1 RJ-45; 2 PS2; 1 VGA; 1 Display Port; 1 serial;

1 parallel; 1 ESATA; 2 Line-in (stereo/microphone); • Minitower Chassis +305W SMPS or equivalent • Warranty: 3 Years Next Business Day On-site Service by Company • Extra Anti Virus (QH/NP or equivalent) with 3 years upgrade. (Pl.

quote its price separately here)

75

2

18.5” Widescreen LED/LCD Monitor Pl. quote separately for LED and LCD.

75

3.

18.5” Widescreen LED/LCD Monitor by buy-backing old CRT monitor Pl. quote separately for LED and LCD.

55




Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


total amount)

q a b (q*a)+b 4.

LCD Projector: Resolution :XGA, 2600 ANSI Luminance, Weight 2.3Kg, Lamp life 4000 Hr(High brightness mode)/5000Hrs on low brightness mode Contrast Ratio: 2000:1, Digital I/p:HDMI x1, USB Input and PC Less Presentation, Power Consumption :280 W, Remote SPEC to modify

5

5.

DLP Projector: Resolution: Native XGA(1024 X 768), Supported VGA(640X480), Brightness : 2600 to 3200 ANSI Lumens, Contrast Ratio: 5000:1 (Full on / Full off), Image size: 24” to 300”, Throw ratio: 1.86 to 2.04 (53” @2M), Zoom ratio: Manual zoom, 1.10:1, Lens: F= 2.56-2.8, f=21-23.1 mm, Lamp life: 230W, 3500 / 5000 Hrs(Normal/Economic mode), Lamp warranty: 12 months or 2000 cumulative hours whichever comes first, Aspect ratio: 4:3 Native, 16:9 selectable, USB Display Support , Remote control, Auto switching power supply 100 to 240 VAC, 50/60 Hz, Power consumption: 318W, standby<1W, Weight: 3.5KG with included accessories (SPEC to modify)

5

6.

Visual Presenter: Specification similar to specification of Make: AVER Model: F30 as similar to CP155 model with a built-in memory plus an SDHC card slot and USB OTG port for extensive external storage. SPEC to modify

5




Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


total amount)

q a b (q*a)+b 7A).

Advanced Software Engineering Lab IBM Rational SEED Program (Upgrade of existing) IBM SEED Program includes:

1. IBM Rational Suite Enterprise -30 floating licenses 2. IBM Rational Software Architect. - 30 permanent licenses 3. Services as follows:

a. Instructor Led Training 4 days up to 10 participants at college premises on

• Essentials of Visual Modeling with UML 2.0 • Essentials of Rational Software Architect

b. Course Material: One set to each participant • Essentials of Visual Modeling with UML 2.0 • Essentials of Rational Software Architect

c. Library Reference Course Material: 1 set for the library • Mastering Object-Oriented Analysis and Design with UML • Essentials of Rational Requisite Pro • Fundamentals of Rational Rose • Essentials of Rational Clear Case

• Essentials of Functional Testing with Rational Robot • Essentials of Rational Application Developer

1




Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


total amount)

q a b (q*a)+b 7B).

Advanced Software Engineering Lab

IBM Rational SEED for Quality Program IBM SEED for Quality Program includes

1. 30 Permanent licenses of Rational Functional Tester (RFT) 2. 30 Permanent licenses of Rational Quality Manager (RQM) 3. Services as follows:

a. Instructor Led Training 4 days up to 10 participants at college premises on o Essentials of the Quality Assurance Practice o Software Testing Life Cycle o Functional Testing Techniques o Automated Testing process, tools & scripting

b. Course Material: One set to each participant

• Essentials of IBM Rational Functional Tester, Java Scripting

• Rational Quality Manager

c. Library Reference Course Material: 1 set for the library

o Rational Principles of Software Testing

1

8.

Microsoft Web Testing Tools

1

9.

Quick Heal Total Security or equivalent Anti Virus for Desktop systems, Educational version ( 3 Years upgrade )

25




Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.

EMD amount (3 % of the total

amount)

q a b (q*a)+b

10.

8085 Microprocessor trainer kits: Intel's 8085 microprocessor @ 3 MHz together with 8255 as well as 8155 chips onboard, Serial Mode communication through RS–232 serial port with a terminal, 50 pin expansion bus for adding study cards, Cable set and Power supply/SMPS.

25

11.

Interfacing Kits: 8255 8255 interfacing card compatible with Dyna85 kit.

2

12.

DC Dual power supply- 0-30V range and 2A/5A current (Pl. quote separately for 2A and 5A.)

2

13.

SMPS for Dyna85 kit

4




Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


amount)

q a b (q*a)+b

14.

Branded Laptop Intel®Core™i5 2410 M Processor (2.30GHz,3MB) or higher, 500GB@5400 RPM SATA Hard Drive, 4GB 1 DIMM (4GB x1) DDR3 @1333 MHz SDRAM Memory, 12.7mm SATA tray load DVD+/-RW 8X, Intel®HM67 Express Chip set Mother Board, Integrated Intel® Graphics 3000 (GT2), Gigabit Ethernet network standard, spill-resistant Chiclets Keyboard with Touchpad (English), 39.6cm (15.6" inch) WSVGA LED Anti-Glare Display (1366 x 768), 1.3 MP Integrated Webcam, Main Speakers (quantity) : 2 x 2.0Watt ,Digital MIC, Linux Ubuntu 10.04, VGA, HDMI, RJ-45, Power, headphone/Microphone out, (3) USB 2.0, Wireless 802.11n & Bluetooth 3.0 combo Card, 3-in-1 Card Reader / Carry Case / 48Whr 6 cell (2.2amp) Battery , Warranty : 3 Year Next Business Day On-site Service

10




Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


amount)

q a b (q*a)+b

15.

Mini Laptop / E-tab / Net book (Pl. quote separately for each of the three) Intel® Atom™ processor N455 (1.66GHz/667MHz FSB/512K L2Cache) or higher, 250GB @5400 RPM SATA Hard Drive, 2GB (1 X2GB ) Non ECC DDR3 @1333 MHz SDRAM Memory, No Optical Disk Drive, Intel® NM10 Express Mother Board, Integrated Intel® Graphics Media Accelerator 3150, Integrated 10/100 Ethernet LAN, Internal Keyboard with Touchpad (English), 25.7cm (10.1 inch) WSVGA True Life™ (1024 x 600), 0.3 MP Integrated Webcam, Main Speakers (quantity) : 1 x 2.0Watt , Digital MIC, Microsoft® Windows 7 Starter 32 Bit (English) and Office Starter 2010 USB 2.0 (3), LAN (RJ45,15-pin VGA,7-in-1 Media Card Reader, HDMI,AC adapter,(1-line out, 1 mic-in) Wireless 802.11n & Bluetooth 3.0 combo Card 7-in-1 Media Card Reader, Carry Case, 48Whr 6 cell (2.2amp) Battery , McAfee® Security Center™ (Multi-Language) - 15 Months Promo, Starting weight of 1.56Kg7 (3.44 lbs) with 6-cell battery Warranty : 3 Year Next Business Day On-site Service, 1 Year Complete Cover Accidental Damage Protection

10


Page 11 of 36 Seal and Signature of Bidder


Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


amount)

q a b (q*a)+b

16.

Thin Client (Server based computing) as standalone PC Can connect to Windows2Kx/XP/WIN7 /Linux/ VNC/Sun Solaries / ICA. Specifications: Thin Client for Multiple Server Support CPU : Intel 1.0 GHZ CPU / VIA 800 MHZ or higher Hard-Disk : 2.5" Laptop HDD can be fitted Memory : 128 MB (Expandable) DOM : 128 MB (Expandable) Ports : 1 LPT1, 2 USB, 1 Serial, 2 PS/2, Audio & VGA LAN : 10/100 MBPS on Motherboard Size & Weight : 10”X7.5”X2.5”, 1.5 Kg Cabinet : Mini – ITX Cabinet Power Supply : +12V @ 5A (60 watts adapter based power supply) Resolution support -1920 X 1440 - 24 Bit

60



(2) Electronics Engineering Department:


Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


amount)

q a b (q*a)+b 1

Digital storage C. R. O. • Dual Channel, Bandwidth : 25MHz/40 MHz per channel • Min. 8” TFT LCD, with back light • Sampling Rate up to 100MSamples/Sec on each channel • Average and peak detection • Advanced Triggering on Edge, Video triggering • Min. 20 Automatic Measurements Functions • Manual Cursor Measurement • Min. 4 Waveforms, store/recall • Mathematical Functions, FFT • Zoom with Delay Scan • Built-in USB Interface with associated software for capturing the screen

and printing it. • Auto-set, Capable of Fast Setting, Auto Scale, Automatic Calibration • Battery Operation, Built-in Battery Charger • With accessories necessary (probes, cables, manuals etc)

17 Nos.

2

Digital storage C. R. O. (Under Old Aplab make C.R.O. in buyback scheme)• Dual Channel, Bandwidth : 25MHz/40 MHz per channel • Min. 8” TFT LCD, with back light • Sampling Rate up to 100MSamples/Sec on each channel • Average and peak detection • Advanced Triggering on Edge, Video triggering • Min. 20 Automatic Measurements Functions • Manual Cursor Measurement • Min. 4 Waveforms, store/recall • Mathematical Functions, FFT, Zoom with Delay Scan • Built-in USB Interface with associated software for capturing the screen

and printing it. • Auto-set, Capable of Fast Setting, Auto Scale, Automatic Calibration • Battery Operation, Built-in Battery Charger • With accessories necessary (probes, cables, manuals etc)

15 Nos.




Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


amount)

q A b (q*a)+b 3

Signal Generators 0 to 1MHz sine, square, triangular waveform. Separate TTL output terminal. Output should be protected against short circuit. Adjustable DC shift in the output. Adjustable duty cycle between 10% to 90%, With accessories necessary (probes, cables, manuals etc)

17 Nos.

4

Signal Generators (Old Signal Generators in buyback scheme)0 to 1MHz sine square triangular waveform. Separate TTL output terminal. Output should be protected against short circuit. Adjustable DC shift in the output. Adjustable duty cycle between 10% to 90%, With accessories necessary (probes, cables, manuals etc)

15 Nos.

5

Power Scope Two Independent channels with Differential Inputs, Alt or Chop at 100KHz , Max I/P ±1000V dc or 660V ac rms , x10, x100 Attenuation for large amplitude input signal, DC - 20MHz Bandwidth, 50mV/div Sensitivity on Both Channels, X-Y Operation, 5mV/div Sensitivity when used as an Oscilloscope, 40ns/div to 0.2s/div Time Base, Rectangular CRT with Internal Graticule, Triggering DC to 30MHz, Z modulation, TV Triggering Frame (V) & Line (H), LINE Trigger, Component Tester, With accessories necessary (probes, cables, manuals etc)

4 Nos.

6

Universal IC Tester and Programmer Facility of Testing a wide range of Digital IC's such as 74 Series, 40/45 Series of CMOS ICs, Micro- processor 8085, 8086, Z80, 8051, 89c51,89V51 RD2, 89 series microcontroller Peripherals like 8255, 8279, 8253, 8259, 8251, 8155, 6264, 62256, 8288, 8284, wide range of Analog IC's such Op-amp, 555 Timers, wide range of Transistor Arrays, Analog switches, Opto-couplers, ADC, DAC, Comparators, Waveform generator, PWM IC, Sample Hold IC, Voltage Regulator, DPM IC, Frequency to Voltage converter, Latch driver, VCO IC’s, PLL IC’s, Cross Point Switch, Seven segment display of common cathode & common anode type, Auto search facility of all Digital ICs, Facility of test by: Truth table/sequence table comparison. ZIF: 40 pin DIP ZIF sockets, required adapters (if any) included. Keys: High reliability Key pad with numerical & functional keys.

1 Nos.




Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


amount)

q a b (q*a)+b 7

Power Electronics Experimental Set-up • Demonstration Set-up for characteristics of power devices like SCR,

TRIAC, MOSFET, IGBT etc. • Single Phase and Three Phase Inverter using MOSFET/IGBT • DC Motor Drive (Chopper based) • Four Quadrant DC Drive-Dual converter • Transistorized (MOSFET/IGBT) Chopper • Three Phase Controlled Rectifiers

1 Nos.

8

8051 educational trainer Kits Based on Philips 89V51RD2, Min. Eight LEDs, On-board 16x2 character LCD module (facility of connecting 40x2 LCD preferred), Min. two on-board relays (screwed connectors preferred), I2C based EEPROM 24C512 (64K), I2C based Real Time Clock (DS1307) with square wave output , I2C based 8 bit, 4 channel ADC and a DAC with voltage output., Facility of connecting extra user I2C peripherals, All port pins should be available on connectors (extra SIP connectors for each port preferred), Serial port with DB9 female connector, Facility of connecting stepper motor driver (on board driver preferred), On-board 4x4 matrix keyboard. Configurable rows / columns through DIP switches, All peripherals should be detachable. On board clock generator, In System Programming (ISP) support, On-board logic probe, On board buzzer, Test points provided for serial, I2C, Interrupts, Test points for monitoring important MCU signals, Keys for giving interrupts indication. Enclosed in Wooden cabinet, User manual, Laboratory Manual with example projects in Keil (uV4 or higher) IDE, Facility of serial port based single stepping through Keil uVision software.

4 Nos.




Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


amount)

q a b (q*a)+b 9

Peripheral boards for 8051 kit

The peripheral boards must be compatible with item number 8. They should be supplied with Example C programs, Laboratory Manual and required cables

1. Multiprocessor boards

• Master and slave boards • Max 7 slaves should be able to be connected to master using RS485 • Facility of programming on slave board also • Slave should have selectable address setting, Min 4 LEDs, min 2 push

buttons and min 2 toggle switches. RS485 base communication between master and slave

2. Graphic LCD interface boards • 64x128 BW display • 5 keys for Up, Down, Left, right and enter • Example C programs for text and graphic display with key handler

programs 3. ADC0809 interface board

• Buffered LEDs for monitoring data and control signals • All channels on screwed connector for easy connections • Demo of multichannel programming should be possible with pots to min 2

channels 4. DAC0808 interface board

• Voltage output 0-5V (Gain adjustment is preferred) • Buffered LEDs for data and control signals • Bar graph indicator to view analog output • Speaker with amplifier for audio indication if DAC is used for waveform

generation 5. Thumb-wheel interface board

• 4 thumbwheels with push operation • Multiplexed mode operation, LEDs for data and select lines

2 No. each




Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


amount)

q a b (q*a)+b 10 Programmable Logic Controller with Accessories

• Min 14 I/O Channels, Digital/Analog Inputs • Digital Output, Relay, 500 mA , with short circuit protection • Min. 4 high speed inputs, frequency 20 kHz/5 kHz • RTC, Serial Ports: RS232 / 485 / 422 / modem interface, remote monitoring • PID, Programming software • AC/DC motor controller module with motor • Associated software for programming using the ladder diagram, simulation

and downloading it in PLC.

1 Nos.

11 Temperature Controlled soldering station Temperature adjustable up-to 450 deg. digital readout required

2 Nos.



3) Chemistry Department:


Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


amount)

q a b (q*a)+b 1 Electric Oven l4” x 14” x 14”

Digital Lab Hosp Make

Temperature range 300˚C

01

2 Digital pH meter Model 335/Similar

Elico/ Equiptronics/ Systronics Make

Digital display, Combined electrode

02

3 Conductivity meter Model 306/Systronics/Similar


Digital Display, with stand & Conductivity cell

02

4 Photo colorimeter Model 112 Systronics/Similar


01

5 Top pan balance

1mg accuracy 125 g max

Contech/ Shimadzu/Citizen Make

01



(4) Electrical Engineering Department:


Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


amount)

q a b (q*a)+b 1 1) Digital Energy Meter calibration Set (2000W).

2) Temperature Sensor Kit max. Up to 5000C.

01 Set

01 Set

2 1) LVDT Kit (Maxi. Dist.) 2) Speed Measuring by Magnetic Pickup Bench upto 1000 t0 2500 rpm.

01 Set

01 Set

3 1) Microprocessor Based Over Current Relay system. With pre settable DMT, IDMT, VI & EI characteristics Time multiplier setting. 2) Microprocessor Based Impedance Relay. 3) Microprocessor Based Universal Relay Test Kit. As per following specification i) All the relays should be of standard make e.g. AREVA, ABB, Siemens, ALIND etc, ii) Relays must be compatible to the test Kit. iii) Voltage source 0‐300Vmax (300VA min.) iv) Current source 0‐20A max. (150 VA min.) v) Digital timer for trip time measurement vi) MCB protection for panel. vii) With isolation transformer and cooling Fans. viii) Completely wired for use.

01 Set

01 Set

01 Set

01 Set




Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


amount)

q a b (q*a)+b 4 1) 8255 Study Cards to be interfaced with 8085 System of Dynalog

Microsystems with FRC (50 pin). 2) 8253 Study Cards to be interfaced with 8085 System of Dynalog Microsystems with FRC (50 pin) 3) 8279 Study Cards to be interfaced with 8085 System of Dynalog Microsystems with FRC (50 pin). System.

08 Nos.

08 Nos.

05 Nos.

5 1) Multiprocessing Control System Level and flow Control System with PC interface and SCADA Software 2) Control System Trainer kit, Open Loop, Closed Loop, Lag, Lead, Compensator Network

01 Set

01 Set

6 1) DSP Starter Kits for motor control application TMS 320 F 2812, Running at 150 MHz, 128 k words, 0‐wait state external RAM, 2x12 bit accuracy D/A outputs, RS 232, CAN‐bus and JTAG interface real time serial communication monitor, PROCEV28X, Processor evaluation software (with ASM source code.)

04 Nos.



(5) Physics Department:


Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


amount)

q a b (q*a)+b 1

Research Optical Bench:- The bed is a heavy cast channel with a strong central rib, thoroughly seasoned and aged before Machining and grinding of its upper surface. The dimensions of the bed are approximately 180 cms x 12 cms x 16 cms. In size provided with heavy leveling screws. The scale is 170 cms. Long. Complete with four accessories. Description of accessories as follows. a) OPTICAL SLIT:- Manipulation of jaw movement free from any spring control ensuring maintenance of original accuracy even after prolonged use. The following adjustments to be provided for the slite & its carriage. 1) Linear adjustment along the, bed read by vernier to 01 cms. 2) Fine vertical adjustment by slow motion screw. b) BIPRISM HOLDER :- 1) Provided with following adjustment. 2) Linear adjustment along the bed, read by vernier to 01 cms. 3) Fine vertical adjustment by slow motion screw. 4) Quick radial motion along the horizontal axis. 5) Fine radial motion along the horizontal axis. c) LENS HOLDER :- With spring top for ease in fixing carriage provided with adjustment as for the optical slit. d) Micrometer Eye Piece :- 1) Provided with following adjustment. 2) Quick linear adjustment along the bed ready by vernier to .01 cm. 3) Fine Micrometer Vertical adjustment. 4) Micrometer cross motion of eye piece along a 30-0-30 mm scale read on a micrometer head to .001 cm 5) Complete as described above having brass scale. 6) Having Stainless Steel Scale.

01



6) Applied Mechanics Deptt.


Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


amount)

q a b (q*a)+b 1

REBAR LOCATOR : By Magnetic field locates bars in R.C. Structures. For detecting reinforcements in cement concrete with easy to read, liquid crystal display to estimate rebar size to depth up to 200-300mm.

01

2

SIEVE SHAKEER - Gyratory type This sieve shaker is designed to carry up to 7 sieves of 6 inch or 8 inch diameter. The 12 inch dia. sieves can be used with the help of Adaptor. A ¼ HP. motor through a reduction gear immersed in oil drives the shaker. The sieve table dies not rotate but is inclined from the vertical axis and the direction of inclination changes progressively in clockwise direction. If the stop-pin below the table is removed. The shaker can have a rotary motion. In addition to this gyratory motion of the table, there is an upward and downward movement ensuring that each square cm of the sieve is utilized. A pair of rods and a holder is supplied. The holder can be fixed on the top of the upper most sieves, and thus the sieve set is firmly held. Suitable for operation on 230 volts, 50 cycles single phase A.C. Supply. Supplied without Test Sieves but with Mechanical time switch IS Sieves: 20 cm dia. Brass frame Test sieve: Made out of rolled Brass, Spun Body frame without joint. Folded bottom having beading at top, tight fitting with each other. Mounted with stainless steel cloth, with top lid & Collecting Pan of following sizes: 4.75 mm, 3.35 mm, 2.80 mm, 2.36 mm, 2.00 mm, 1.70 mm, 1.40 mm, 1.18 mm, 1.00 mm, 850 Micron, 710 Micron, 600 Micron, 425 Micron, 355 Micron, 300 Micron, 180 Micron, 150 Micron, 90 micron, 75 micron) 30cm dia. GI Frame Test sieve: For Coarse aggregates the frame in made galvanized Iron sheet with joint having the steel perforated sheet with square holes, with top lid & Collecting Pan of following sizes: (80 mm, 40 mm, 20 mm, 16 mm, 12.5 mm, 10 mm, 6 mm, 3 mm, 4.75 mm)

01




Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


amount)

q a b (q*a)+b 3

Mortar Cube Moulds of size √ 50cm2

CUBE MOULD: Size: 50mm x 50mm x 50mm: Made of cast iron split duly machined inside accurately complete with base plate as per IS 516-1959. Cube Mould 12 to 12.5kg Weight with locating pins.

12

4

Concrete Cube Moulds of Size 6”*6”*6” Concrete Moulds: CUBE MOULD: Size: 150mm x 150mm x 150mm: Made of cast iron split duly machined inside accurately complete with base plate as per IS 516-1959. Cube Mould 12 to 12.5kg Weight with locating pins.

24

5

VICAT NEEDLE APPARATUS WITH DASHPOT: Consisting of a metallic frame bearing a movable rod with cap at one end and a vicat mould 70 mm in dia at the base, 50 mm at the top and 40 mm high & with a glass base plate consistency plunger, initial and final setting needles in a nice jewellary case. With dashpot to facilitate the gentle lowering of the needle RELEVANT STANDARD: IS: 5513.

02

.



(7) Civil Engineering Department:


Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


amount)

q a b (q*a)+b 1 Ultrasonic Type Clamp Flow meter

B) Technical Specifications: Flow Sensor Model : OPTISONIC 6000 Version : Single Beam with 2 Sensors Type : Transit Time Process limitations: Solid particle content less than 3% by volume. Gas content less than 2% by volume. Mounting : Strapped on the pipe / clamped on Rail / Cover Material : Die cast Aluminum with Polyurethane coating Temperature Limits : Process: - 40 to +120 °C Ambient: -40 to +65 °C Protection Category : IP 67 Accuracy : +/- 1% of measured value for pipe line size greater than 2” and Flow Velocity Range (0.1 to 20.0 Meter per second) Signal Converter Model : UFC300 W Version : Remote field mounted 10 mtrs. sensors cable Area : Safe Housing : Polyamide Polycarbonate wall mounted Power Supply : 230 VAC (-15/+10%) 50Hz Output Signals : 1 x 4 – 20 mA HART, 1 x Pulse output Local Display : Large LCD for displaying actual flow rate, Velocities of sound, forward, reverse and sum totalizer Protection Category : IP 65/IP67

01




Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


amount)

q a b (q*a)+b 2 Primavera

Contractor (Student Version)

(Brand product specifications for soft ware from ORACLE corporation)

Ten (10) User

Package, Licensed Soft ware

3

Digital Analytical Balance Model No: CX-120 } and Make: Citizen } similar Specifications Capacity: 120gm Readability: 0.1 Mg Producibility: +/-0.1 Mg Linearity: +/-0.2 Mg Pan Size: 80mm Response Time: 3 Sec. Calibration: Fully Automatic Motorized Internal Calibration Operating Temperature: 0-45oc Weight Approx.: 5.3 Kg Power Supply: Ac Adapter 230 V +/- 20% 50-60 Hz Unit Available: G, Mg, Ct, Lb, Oz Weighing Chamber Height: 225mm Built In Interface Port: Rs. 232 C Standard Equipment: Dust Cover, Ac Adapter Supplied: Draft Shiel And Operational Manual Display: Large Lcd With Backlight Display

01



(8) INFORMATION TECHNOLOGY DEPARTMENT :


Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


amount)

q a b (q*a)+b

1

All in One Touch Screen desktop computer 2.4 GHz AMD Athlon II 4 GB DDR3 RAM 1TB SATA Harddisk 7200 RPM ATI Radeon HD 4270 Graphics LCD wide screen 23’ display with 1920*1080 resolution with buyback of colour CRT monitor Wireless mouse and keyboard Integrated 1.3 MP webscam and mic 802.11n WiFi Extra Built in TV tuner (Optional, Cost to quote separately)

15

2

PDA Mobile Phone Screen - Multi touch Screen, 7” to 10” Display size, Processor- 1.5 GHz, Operating System- Windows7/Android 2.2 , Camera- Dual Camera (3 to 5 Mega pixel Primary & 1 to 3 mega pixel Secondary camera) , RAM- min 1 GB, Internal Storage- 16 GB to 32 GB, Features Supports - 3G, EDGE, GPRS, GPS, Wi-Fi, Blue tooth, video recording, Quad-band - GSM/GPRS/EDGE , Connectors -3.5 mm stereo audio jack and Standard micro-USB (12-pin micro-USB 2.0),

2




Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


amount)

q a b (q*a)+b

3

GSM Mobile Trainer Multi band GSM, GSM Modem and Components, SIM, AT commands, Voice with AT command, sending text message using flow code software

1

4 CDMA Mobile Trainer CDMA, DSS, error correction, PN sequence

1

5

Net Book Intel Atom based Dual core 1.5 GHz Processor , 2GB RAM, 320 HDD

2

6

Switch, Layer 3 SNMP Managed with Added Features 12 Gigabit Fiber port switch

1

7 Routers Type-3:2 LAN, WAN ports & 2 WAN Slots IPv6 ready with RPS Support

1



(9) Mechanical Engineering Department:


Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


amount)

q a b (q*a)+b 1 Digital Anemometer

Digital Anemometer for measurement of wind speed and direction. Specifications:- Speed Range:- 0 to 45 m/s Accuracy :- ±2% @ 12m/s Direction Range:- 0 to 359o

1

2 Cooling Tower: Inlet condition-water Temp from condenser: 500C, Exit Temp required from cooling tower: 280C, Condensate Extraction pump: 3 HP motor with 300 liter per minute flow rate (Already installed). FRP tower 3mm thick, size-1525 x 1525 x 2200 mm With opening 51mm dia. with flange connections FRP Basin 4 mm thick, Size 1525 x 1525 x 350mm (max) with 800 liter Capacity , Openings 2 Nos., Air inlet louvers FRP with Iso - phaling resin Squirrel cage Induction motor of 720 rpm, 1.5kW (415 V, 50 Hz), F class

Insulation: Fan-Solid FRP construction with aerodynamic shape with approx dia. 1200 mm, Air flow rate 5.9 cubic meter per second, Axial flow type

Fills & Nozzels-100% virgin PVC capable to sustain temp of 550C of make MAQUA/COOLDECK or equivalent with total wetted surface area 3320 sq. m, cooling capacity 483000 kcal/hr with size limitation 1520 x 1520 X mm 2000, nozzles to be included according to the size limitation.

Heavy graded steel Frame as per IS 2062, IS 808, Is1731, IS1730 with Test Certificate (Self/Metallurgical Lab).

1




Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


amount)

q a b (q*a)+b 3 Vacuum Pump & vacuum gauge

Two stage direct drive rotary vacuum pump with ultimate vacuum 0.001 bar along with Digital low pressure pirani gauge with range 1000 mbar to 0.0001 mbar with sensor one /two.

1

4 Strain indicator Micro processor based strain Indicator, I/P 8 CHANNEL, Range +/- 10,000 micro strain, Accuracy o.1 %, Resolution 1 micro stain, Bridge excitation 5v dc, Gauge factor 1.5 to 3, Gauge factor adjustment by key board programming, output will be provided to communicate with computer through data cable and licensed interface software.

1

5 Strain gauges: wire / foil type size 1mm, 2mm and 3mm and three element rosette type (triaxial) sizes 1mm, 2mm and 3mm.

30




Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


amount)

q a b (q*a)+b 6

CNC Lathe Machine With installation Capacity Swing over bed 350 - 500 mm Maximum turning length 250 – 400 mm Standard turning diameter 100- 200 mm Maximum turning diameter 200- 300 mm Slides X – Axis Travel (Cross) 100 - 150 mm Z – Axis Travel (Longitudinal) 250 – 400 mm Rapid feed rate (X and Z axis) 18 – 24 m/min. Main spindle Spindle speed range 50 – 4000 rpm Full power range 600 – 3000 rpm Spindle power 5.5 / 7.5 KW (with Fanuc or

Siemens) Spindle bore 50 - 70 mm Maximum bar capacity 40 - 50 mm Accuracy Positioning 0.015mm Repeatability +/- 0.005 mm Power Chuck 150 -200 mm Dia Power / Hydraulic Turret 6 -8 stations Tailstock Programmable Quill Voltage Stabilizer 15 - 20 KVA

1



(10) Central Computing Facility :


Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


amount)

q a b (q*a)+b 1

Storage Area Network (SAN) with 6.5 TB Raw with min. configuration • Scalable to higher in size by adding disk drives & enclosures, SAS disk in RAID

5 (with 6 Gbps 600 GB 15k rpm drives) + one hot spare disk. • Each SAN must have at least two controllers running in an active‐active mode

with automatic failover to each other in case of one controller failure. • Intel Xeon Dual Core CPU (min.), min. of total 16 GB controller cache The

cache on the storage should be protected by battery backup or destaging. • Supports storage must have iSCSI, NFS and CIFS protocols for use with

different applications, SAS and SATA/NL‐SAS based disks simultaneously • Striping & Mirroring, Single Parity and Dual parity RAID types for natively

attached storage, Front‐End fully configured connectivity • Hot spare drives to reduce downtime, a unified storage & must have the

ability to combine multiple RAID Groups into a single entity so as to create LUNS/Volumes using Multiple RAID Groups and hence from the single entity to give maximum performance to all the applications being served or equivalent.

• Must support for thin provisioning, have redundant hot swappable active & passive components like controllers, disks, power supplies, fans, standard security features.

• To improve the TCO, built‐in support for removing redundant data through deduplication on the primary storage system. Built‐in Support for file compression, Snap‐short features, Host support of min. 128 SAN hosts. All the licenses for mandatory features mentioned on the storage system must be provided for the entire capacity, OS supported and logical partition (LUN masking supported ) by the system from day one or should be unlimited for the entire BOX capacity, scalability. Must have support for industry‐leading Operating System platforms, Capable for Remotely Diagnosticsed ,AC Powered, Rack Mountable,

• Quote with 3 years on site support containing comprehensive warranty for

1




Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


amount)

q a b (q*a)+b Hardware and Software and installation,

• Bidder must quote separately for Disaster Recovery

2

Supply & Installation of UPS Batteries (A)Quanta / Exide Make 12V-100AH SMF Batteries

1. Two Years Warranty 2. Three Years Warranty

(B) Exide Make 12V-40AH Tubular Batteries with 5years warranty Model-6EL40+ (Please quote separately for above 3 items)

20

3

Manageable L2 Switch Web Smart Gigabit (24 Port) 24 Port (24X10/100/1000, 2X Mini-Gibic open Slot +One Mini.Gibic MM Module) (Compatible to Presently Installed L3 Switch HP-Procure Switch)

6




Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


amount)

q a B (q*a)+b 4

Mail Server to be provided with domain name walchandsangli.ac.in (Already Registered). The Bidder must have his own Mail-Server who will provide following Secure and Encrypted mailing system, Dedicated e-mail ids for above domain, Multi Domain and Sub-domain facility with functioning with various mail clients as MS Outlook, Outlook Express, IE, Mozilla etc. Mail Filtering by Anti SPAM and Anti Virus, Control on File/MIME type for Attachments, Mail Group Facility, Group Moderate features, Support for all mail protocols, work with all hand held mobile devices, Incoming/Out going Mail Forwarding, BCC, for USER/Domain, Sender Authentication (by User/Network wise),SSL Enabled servers, Real Time Black list, Domains checks, Email Alising, Scheduled Configuration/Mail box Backup, Global Address book, Domain wise disclaimer for multiple domains, User Account Management, control on attachment size, Personal Address book, Control on Internal/External access for the user. Webmail (Disk Quota per user min. 250 Mb) Task Management, Option for notes creations, Calendar for making appointment, Auto Mail responder (Out of College ) facility, Multi folder support, Password management, Notice Board (To public notice or announcement), Multilingual support for Webmail, Delivery notifications, Webmail HTML View/Compose, Rules can be set for message filtering, message to highlight.

250 users



(B) Supply of Roof sheets to Mechanical Department


Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


total amount)

q a b (q*a)+b

1 G.I.Roof Sheets of 20 Gauges for area 6800 Sq. Ft. approx. (10 ft. X 2.2 Ft.) 400



(C) Exam Cell- Supply of Answer books


Qty

Basic Unit

Price

VAT + Other

(Except Octroi)

Total

Amount Rs.


total amount)

q a b (q*a)+b 1 Number of Pages: 42 (Back to back)

A4 size, ruled, side stitched answer book and last page printed with graph (70 gsm Map litho paper) Serially numbered starting from A 63001

20000

2 Number of Pages: 22 (Back to back) A4 size, ruled, side stitched answer book and last page printed with graph (70 gsm Map litho paper) Serially numbered starting from M 57523

20000

3 Number of Pages: 04 (Back to back) A4 size ruled and side stapled answer book (70 gsm Map litho paper) Serially numbered starting from S 16501

4000

4 Number of Pages: 08 (Back to back) A4 size, ruled, side stapled answer book and last page printed with graph (70 gsm Map litho paper) Serially numbered starting from P 17771

8000

Note: The quality of the pages and matter to be printed on each type of above answer book are available in examination cell of the college. The same quality and the matter are to be delivered at the supply of the order.


Page : 35/36 Seal & Signature of Bidder

Terms & Conditions Please note following terms and conditions before filling the tender form and return this sheet duly signed along with company’s seal.

1. Essential additional Services to be included Installation, calibration and training on college site. Supplying documentation, Software Media /Software with media. (Licensed Version), Warranty for three years. Equipment for its malfunctioning, if any, must be replaced / repaired within 15 days during warranty period.

2. For any proprietary items, attach certificate from the manufacturer that the product is proprietary and also attach the valid certificate of authorized dealer/distributor/channel partner.

3. Local support for three years must be provided by the party/manufacturer. 4. The name of your principal party (if any) is to be indicated for the items, so as to enable

to place the order with the principal, if required. 5. The contract shall be for the full quantity as described above. All duties, taxes and other

levies etc. (except octroi) are to be clearly indicated and should be included in the “Total amount”. The octroi paid receipt is mandatory and it should be in the name of Director, Walchand College of Engineering, Sangli. The prices should be quoted in Indian Rupees only.

6. The right to reject or accept in part any or all offers with or without modifications from any or all parties without assigning any reason is reserved with the Director, Walchand College of Engineering, Sangli.

7. The bidder has to submit an undertaking for terms and conditions, if selected for placing the order.

8. Rates quoted should be valid at least for One Month after the date specified for submission.

9. Any conditional tender will not be accepted and quantity of the items may vary as per requirement at the time of purchase order.

10. The complete delivery of all the items should be within 15 days from the date of purchase order. Amount of penalty for delayed supply of goods will be decided by the Director. Generally, the penalty for delay in proportion to the cost of item (usually at rate of 1% for first 10 days, 2% for next 10 days) shall be charged. In case of delay, more than 20 days, order shall be automatically cancelled, unless otherwise approved by the college authorities under special circumstances in writing.

11. Payment will be made immediately after delivery of the goods in following mode: 90% against receipt of goods as per specifications at college and remaining 10%

on submission of three year’s Bank Guarantee for 10% of the total purchase order.

12. For supply of “Answer Books” of Exam Cell, 100% payment will be done only after satisfactory receipt of items at the exam cell.

13. Legal matter will be restricted to Sangli jurisdiction. 14. Quantity mentioned in tender for item may vary depending on availability of fund.

I / We have read the above instructions carefully, and I /we abide by the instructions. Seal of Company Authorized Signature Name: Date:


Page : 36/36 Seal & Signature of Bidder

Details of EMD Sr. No. Department Department

wise Total Amount

Rs. Ps.

EMD

Rs. Ps

D.D. Details D.D. No. D.D. Date

DD/MM/YYYY

Nationalized Bank’s Name

A(1)

CSE

A(2)

Electronics

A(3)

Chemistry

A(4)

Electrical

A(5)

Physics

A(6)

Applied Mechanics

A(7)

Civil

A(8)

IT

A(9)

` Mechanical

A(10)

CCF

(B) Mechanical

(Roof Sheets)

(C)

Exam. Cell (Answer Books)

Seal of Company Authorized Signature Name: Date:

Documents

WALCHAND COLLEGE OF ENGINEERING, SANGLI · WALCHAND COLLEGE OF ENGINEERING, SANGLI ... 8085 Microprocessor trainer kits: ... Cable set and Power supply/SMPS. 25 11. Interfacing Kits: