Upload
travis-monroe
View
227
Download
0
Embed Size (px)
Citation preview
8/10/2019 Verticaldoors General Instructions
1/12
Page 1 of 12 GENERAL INSTRUCTIONS
Installation
Page 1 of 12 GENERAL INSTRUCTIONS
Installation
8/10/2019 Verticaldoors General Instructions
2/12
Page 2 of 12 GENERAL INSTRUCTIONS
Installation
PICTURE ABOVE IS THE UNIVERSAL KIT; YOUR KIT MAY BEDIFFERENT.
THIS KIT INCLUDES:16 M8-1.25X30MM BOLTS
WITH WASHERSRIGHT AND LEFT HINGE
ASSEMBLY2 SHOULDER BOLTS WITH
WASHERS2 SHOCKS _________ PSI
2 PINSTOOLS REQUIRED FOR INSTALLATION:
AIR RACHET, GRINDER ANDCUTTER.
7MM, 8MM,10MM, 11MM,13MM, SOCKETS ANDEXTENSION.
FORK AND PHILLIPS SCREWDRIVERS
SPACERS FOR THE DOORGAP.
3/16 ALLEN WRENCH
1/4 TORX BIT
9/16 WRENCH
LOCKTITE RED
OTHER TOOLS MAY BE NEEDED DEPENDING ON YOUR VEHICLE.
8/10/2019 Verticaldoors General Instructions
3/12
Page 3 of 12 GENERAL INSTRUCTIONS
Installation
UNIVERSAL KITS MAYREQUIRE SOME CUTTING,DRILLING AND WELDING.
Installers with experience recommended
(Note: The pictures on the manual are for reference onlythey may not match your vehicle.)
1)Disconnect the battery.
2)Remove fender:
Remove all Phillips screws orfasteners from the wheel well.
sually you willUhave to removebolts to loosenthe bumper.
8/10/2019 Verticaldoors General Instructions
4/12
Page 4 of 12 GENERAL INSTRUCTIONS
Installation
Remove all bolts from
emove bolts from
.
the top of the fender.
Rthe bottom of thefender by the door
Usually you will have to remove (1)
bolt holding the fender.At this point you should be able toremove the fender.
8/10/2019 Verticaldoors General Instructions
5/12
Page 5 of 12 GENERAL INSTRUCTIONS
Installation
3)Remove the door catch:Open the door and removebolts from the body and from
the door. Push the door catchinside the door.
You will need to remove thedoor panel to retrieve the doorcatch.
4)Usually you will need to morewire slack:Remove foot trim, under it you
will find wire harness use thefork to undo the wire harnessand pull some wire. This willgive you the necessary wireslack to fully open the newVertical Doors Inc. system.Some times you will have toremove the door panel andspeaker and gain the wire frominside the door cavity.
8/10/2019 Verticaldoors General Instructions
6/12
Page 6 of 12 GENERAL INSTRUCTIONS
Installation
5)Close door and use painters tape to secure the door inpreparation for factory hinge removal.
Add spacers after factory
hinges have been
removed.
Usually you will need a 13mm socket to remove the factory hinges.
Hint* (You can make your spacer out of paint sticks and about 8-10turns of blue painters tape)
6)Install new Vertical Doors Inc. system:
In order for the vertical hinge to sit flatagainst the apron you might have tocut, drill or well depending on youparticular vehicle. The new VerticalDoors Inc. system should sit flatagainst apron to work properly.
Hint* Tighten the bolts on the door firstand then install the bolts on the body.
8/10/2019 Verticaldoors General Instructions
7/12
Page 7 of 12 GENERAL INSTRUCTIONS
Installation
1) GREASE
2) LOCKTITE
3) GREASE
*IMPORTANT STEP: DO NOT SKIP THIS STEP. THIS STEP ISCRUCIAL IN YOUR INSTALLATION PROCESS, IF THIS STEP ISNOT COMPLETED WHEN INSTALLING THE VERTICAL DOOR
KIT; ALL WARRANTIES ARE VOIDED, AND MAY CAUSEFUTURE PROBLEMS WITH YOUR VERTICAL DOOR SYST1
EM.
t red Locktite, where the arrow is pointing, on
rease on the bottom side of the shock end.
WARNING! THE USE OF ANY TYPE PLYERS, PAINT OR
ST, make sure you put grease on the body of shoulder bolt where
the arrow is pointing.2
ND, make sure you pu
thread of shoulder bolt.3
RD, make sure you put g
FOREING MATERIALS ON THE SHOCKS BODY OR SHAFTWILL VOID THE WARRANTY.
8/10/2019 Verticaldoors General Instructions
8/12
Page 8 of 12 GENERAL INSTRUCTIONS
Installation
7)Once hinge is locked in place, break nut #1 then turn Allen setscrew #2 on fig until it hits the block then open the door andcontinue to adjust until the door matches with the striker, open andclose door making sure it closes like factory.
SCREW #2
NUT #1
BODY OF
CAR
DOOR
Hint*(leave #1 nut loose until shock is installed Allen set screw willhave to be re-adjusted after shock is installed.
8)Install the shock.
2
3
1
Hint* (You will need a helper to raise the door). (Slip the sphericalrod mount into the spherical ball bearing (1). Using a 1/4 Allenwrench, tighten the screw into the swing arm (2). After the shock isinstalled secure it by installing the pin in the bottom shock end (3).
8/10/2019 Verticaldoors General Instructions
9/12
Page 9 of 12 GENERAL INSTRUCTIONS
Installation
9) After shock is installed re-install door panel and lift the door.Adjust door opening screw #3 clockwise until distance between nuband swing arm is enough so that the swing arm moves up anddown freely.
Hint* (Fine tune the Allen Adjustment screw (#2) to realigned strikerwith door. After the door is align test door by opening and closing,lifting and lowering door several times.
ADD GREASE TO ZERK FITTINGS
Note: Do not install fender until the adjustment of the door isaccurate, and the set screw is tightly secure. Also make sureeverything is tight, adjustment is set and everything isLocktite.
8/10/2019 Verticaldoors General Instructions
10/12
Page 10 of 12 GENERAL INSTRUCTIONS
Installation
10)Modify factory wire loom:In order to be able to openand raise the door, cut the
factory wire boot in half andadd wire loom to protectexposed wires.
11) Cut the inner lip of your fender to make room for the newVertical Doors hinge. Note: After you have cut the fender use asander or grinder and make sure the surface is completely flat.
NOTE: EXAMPLE ABOVE IS FOR THE MAZDA RX-8 YOUR CARMOST LIKELY, WILL HAVE A DIFFERENT CUT OUT.
8/10/2019 Verticaldoors General Instructions
11/12
Page 11 of 12 GENERAL INSTRUCTIONS
Installation
SOME TIMESYOU WILL ALSOHAVE TO TRIM THE LIP ON THEDOOR (IF IT HAS ONE).
EXAMPLE ON THE RIGHT IS OFA CHEV. CORVETTE.
12)Close the door and replace the fender by reversing step 2.
Hint*(Make sure the electrical wires dont get pinched enough todamage wires)
13)For the other side just follow steps 2-12.
8/10/2019 Verticaldoors General Instructions
12/12
Page 12 of 12 GENERAL INSTRUCTIONS
Installation
Thank you for your purchase of the
VVEERRTTIICCAA LL DDOOOORRSSIINNCC.. SSYYSSTTEEMM
Simply Uplifting
NOTE:Vertical Doors Inc. assumes no responsibility for any damages
caused by improper installation