Upload
others
View
4
Download
0
Embed Size (px)
Citation preview
velocity
velocity standard 08V-S-08Chic and robust - a highly-structural portable 10’x20’ exhibit that emphasizes your identity and message seamlessly with a combinaton of fabric graphics, rigid accents and accessories.
dimensions:Hardware Graphic
Assembled unit: 209.9”(w) x 99.375”(h) x 49.5”(d) approx.5331.5mm(w) x 2524mm(h) x 1257mm(d)
Table:17”(w) x 40.5”(h) x 28.4”(d) approx.433mm(w) x 1028.7mm(h) x 722 mm(d)
Counter:36.37”(w) x 40.5”(h) x 15.12”(d) approx.922mm(w) x 1029mm(h) x 384mm(d)Counter internal dimensions:36.3”(w) x 39.37”(h) x 13.8”(d) approx.922mm(w) x 1000mm(h) x 351mm(d)
Panel A,B,C:Total visible area: 11.81”w x 87.32”h299.9mm(w) x 2217.9mm(h)Panel D,E,F:Total visible area: 46.30”w x 86.61”h1179mm(w) x 2199.9mm(h)Panel G & I:Total visible area: 23.62”w x 87.32”h599.9mm(w) x 2217.9mm(h)Panel H:Total visible area: 34.49”w x 86.61”h876mm(w) x 2199.9mm(h)Header:Total visible area: 42.375”w x 12”h1076mm(w) x 304.8mm(h)
Refer to related graphic template for more information
additional information:
- Custom appearance- Easy to assemble- Combination of rigid and fabric graphics- aluminum construction: vertical extrusions 50mm x 100mm- Fully printed counter graphics
features and benefits:- Kit includes one frame, one storage counter, one straight leg table, one graphic header, five fabric graphic panels, four roller graphic panels, seven 50 watt spotlights, three literature holders, one monitor bracket, and five WMC12x6 molded cases- Lifetime hardware warranty against manufacturer defects
08.12.15 © Nimlok Display and Exhibit Solutions WorldwideFor questions contact your local Nimlok distributor
Shipping dimensions - ships in 5 casesEach WMC12x6 case: 52”(l) x 30”(w) x 15”(h)1320.8mm(l) x 762mm(w) x 381mm(h)
Approximate shipping weight (entire kit): 650 lbs / 294.8 kgs
Shipping
Graphic materials: Dye-sublimated fabric & UV prints on 6mm sintra
Table holds max weight 50 lbs / 22.8 kgs
Counter holds max weight 100 lbs / 45.4 kgs
Monitor mount max weight: 50 lbs / 22.7 kgs
Lights included: LV1 50 watt, low voltage spotlight, curved arm, silver finish, 19.5” from end to end
Canopy can be upgraded to printed dye-sublimated graphic
Tabletop colors:
silver black mahogany natural
Parts included
Part label Qty Part code
VE-01 x20 PM4S3-1200-A-A VE-07 x2 PM4S3-600-L-L
VE-08 x2 PM4S3-300-L-L
VE-09 x6 PH2-1200-S-S
VE-10 x1 PH2-900-S-S
VE-99 x2 PS2
VE-11 x2 PH2-600-S-S
VE-12 x3 PH2-300-S-S
VE-13 x10 PH2C-1
VE-16 x4 PH-600-S-S
VE-17 x2 PH-300-S-S
VE-31 x6 PH-351-S-S
VE-40 x2 PM2S-1000
VE-44 x1 PM4S2-300-L-L
V-LWS-CT-03 x1 V-LWS-CT-03
V-LWS-CT-02 x1 V-LWS-CT-02
SP VC-03 x1 C-CAB-02-DR
1.
20'-0"[6096mm]
10'-0"[3048mm]
Part label Qty Part code
Graphic A x1 -
Graphic B x1 -
Panel C x1 -
VE-53 panel D x1 PM4-RB4
VE-53 panel E x1 PM4-RB4
VE-53 panel F x1 PM4-RB4
Panel G x1 -
Panel H x1 PM4-RB3
Panel I x1 -
Header x1 -
Counter infill x3 -
Light x7 LV1-CLP-LIGHT
Monitor mount x1 LM-LB
Graphic clip x19 CTC8
Cable display x3 V-CK3A
Standoff x2 CKSO
Curved canopy x1 V-S-CAN-02
Tool kit x1 V-TK-01
Step stool x1 STEP STOOL
Steamer x1 FABRIC STEAMER-ES
Step 1.Moving from left to right, connect VE-01 uprights at base using the VE-12s, VE-09s, VE-11s and VE-10 where designated in the diagram below. Connect using the attachment detail shown. Note that the VE-09s go into the first and second channel of the VE-01s. Take care to turn locks only half a turn.
EXTRUSION WITH LOCKS
LOCK HORIZONTAL EXTRUSION BYUSING T- HANDLE TOOL
T HANDLE
EXTRUSIONWITH LOCKS
LOCK
EXTRUSION WITH LOCKS
LOCK HORIZONTAL EXTRUSION BYUSING T- HANDLE TOOL
T HANDLE
EXTRUSIONWITH LOCKS
LOCK
2.
EXTRUSION WITH LOCKS
LOCK HORIZONTAL EXTRUSION BYUSING T- HANDLE TOOL
T HANDLE
EXTRUSIONWITH LOCKS
LOCK
VE-12
VE-01
VE-01
VE-01
VE-01
VE-01 VE-01VE-01 VE-01
VE-01
VE-01
VE-09
VE-09
VE-09
VE-09
VE-09
VE-09
VE-10
VE-12
VE-12
VE-11
VE-11
Step 2.Attach VE-13 internal connectors to lower VE-01 uprights using the attachment detail shown below. Slide upper VE-01s over the VE-13 internal connectors to complete the vertical posts.
3.
VE-01
VE-01
VE-01
VE-01
VE-01 VE-01VE-01 VE-01
VE-01
VE-01
VE-13
VE-13
VE-13
VE-13
VE-13
VE-13
VE-13
VE-13VE-13
VE-13
POST W/ STOP
STOP
STOP
1- 2-
TOP
BOTTOM
Tension Glides
Step 3.Connect the VE-08,VE-44 and VE-07 horizontals to the top of the completed VE-01 uprights where designated in the diagram using the attachment detail below.
4.
VE-07
VE-44
VE-08VE-08
VE-07
LOCK HORIZONTAL EXTRUSION BYUSING T- HANDLE TOOL
PH
T HANDLE LOCK
EXTRUSION WITH LOCKS
EXTRUSIONWITH LOCKS
EXTRUSION WITH LOCKS
LOCK HORIZONTAL EXTRUSION BYUSING T- HANDLE TOOL
T HANDLE
EXTRUSIONWITH LOCKS
LOCK
Step 4.Assure monitor mount is secured to the VE-99s using the wingnuts as seen in the attachment detail below. Attach both VE-99s, with monitor mount attached, to the designated VE-01 uprights using attachment detail below.
5.
6.
Step 5.Attach VE-53/VE-54, containing panels D, E, F and G, to the designated VE-01 uprights as shown in attachment detail. Insert graphic clips into VE-09/VE-10 where designated and turn clockwise to tighten. Note that clips go in front VE-09s. Pull graphics down from VE-53/VE-54 and snap rods into clips. When removing, never pull on the graphic, always pull on the graphic rod.
VE-54
VE-53
VE-53
VE-53
BOTTOM
Graphic Rod
DyesubGraphic
MIDDLECHANNEL
EXTRUSIONWITH LOCKS
The CLIP locations are represented byorange dots on the drawings.
CLIP
GRAPHICCLIP
PANEL D
PANEL E
PANEL FPANEL H
LOCK HORIZONTAL EXTRUSION BYUSING T- HANDLE TOOL
PHT HANDLE LOCK
EXTRUSIONWITH LOCKS
GRAPHIC I
GRAPHIC B GRAPHIC CGRAPHIC A
GRAPHIC G
7.
Step 6.Using the attachment detail show, push rubber gasket around edge of panels A, B, C, G and I into the designated channels as shown in diagram below.
TOP
PULL TABS
Fabric graphic is installed by pressing into TOP andBOTTOM channel. To pull the graphic out of the channels, use
TABS on the back side.
BOTTOM
PULL TABS
Fabric graphic is installed by pressing into TOP andBOTTOM channel. To pull the graphic out of the channels, use
TABS on the back side.
PANEL APANEL B PANEL C
PANEL GPANEL I
CKSO
CABLE DISPLAY
CABLE DISPLAY
CABLE DISPLAY
CKSO
STANDOFF DETAIL
GraphicNT
ToggleSTANDOFF
Top
Channel ofextrusion
STANDOFF Barrel
Screw the NT toggle into the base of the STANDOFF barrel and theninsert the NT toggle into the channel of the extrusion and twist to
tighten into place. Next, place the top of theSTANDOFF through the hole in the graphic and then screw on the
STANFOFF top to secure the graphic in place.
INSTALL CABLEDISPLAY IN THE
FRONT CHANNEL
CABLE DISPLAY
Twist in extrusion channel.Gently tight in place
EXTRUSIONCHANNEL
TOP
BOTTOM
EXTRUSIONCHANNEL
Attach STANDOFF to brochure or sintraand gently tight in place. Then link Cables
to extrusions top and bottom
2.5 MMHEX KEY
2.5 MMHEX KEY
BROCHUREOR GRAPHIC
STANDOFF
CABLE
CABLE DISPLAY
STANDOFF
CABLE DISPLAYSTANDOFF
HEADER
8.
STANDOFF
STANDOFF
Step 7.To attach cable display, insert clips on end of cables into the front channel of both the VE-12 and VE-44 and twist gently to the right to tighten. To attach header, connect two standoffs to the front channel of designated VE-01 uprights using detail below. Attach wings to the standoffs using detail below.
Step 8.Assemble the canopy by connecting the pieces following the numbered labels. Clean the frame and place it on a clean surface. Carefully remove the graphic and place it around the bottom of the frame, slits on underside of graphic. Pull the cover carefully over the frame and close all zippers. When breaking system down, be sure to fold or roll the graphic neatly and place in bag.
Screw supplied plates to the top of designated VE-01s as shown in detail below. Slide completed canopy onto tube secured to the plate.
9.
Assemble frame as shown
Frame AssemblyFrame AssemblySET UP INSTRUCTIONS:
1. CONNECT BOTTOM AND TOP RAILS FOLLOWING THE LABELS2. CONNECT SIDE RAILS3. CLEAN THE FRAME AND PLACE THEM ON CLEAN PLACE4. CAREFULLY REMOVE FABRIC COVER FROM BAGS5. PLACE COVER AROUND THE BOTTOM OF THE FRAME6. PULL COVER CAREFULLY UP TO THE TOP7. CLOSE ALL ZIPPERS8. ADJUST FABRIC AROUND THE FRAME
BREAK DOWN INSTRUCTIONS:REVERSE SET-UP STEPS TO BREAKDOWN FRAME
FABRIC CARE INSTRUCTIONS:1. UNZIP COVER ZIPPERS2. CAREFULLY REMOVE FABRIC COVER3. CLOSE ALL ZIPPERS4. FOLD OR ROLL NEATLY5. PLACE FABRIC IN COVER BAG
PART LIST:PER UNIT6 30MM DIA. TUBE SECTIONS1 FABRIC COVER
CURVED CANOPY
12
3
45
6
#8 SHEET METAL SCREW REQUIREDW/MINIMUIM OF 3/4" LENGTH
TO SCREW THE PLATE TO THE EXTRUSION
30MM TUBE
PLATE
VERTICALEXTRUSION
#8 SCREW
ZIPPER
NOTCH BOTTOM FABRIC PANELON CENTER OF THE SPREADERTUBES FOR TUBE CONNECTION
(1.25" DIA.).slits in graphic go on the underside of frame
CURVED CANOPY
Step 9.Lock VE-31s at bottom of designated VE-01 uprights using attachment detail below. Attach SP VC-03 counter door, VE-63 and remaining VE-31 to the secured VE-31s.
VE-31
P90R-1000
VE-31
VE-31
SP VC-03
EXTRUSION WITHLOCKS
LOCK HORIZONTAL EXTRUSION BYUSING T- HANDLE TOOL
EXTRUSIONWITH LOCKS
T HANDLE LOCK
10.
VE-63
Step 10.Slide front and side infills into the channels of the VE-01, SP VC-03 counter door, and VE-63 uprights.
FRONT INFILL
SIDE INFILL
SIDE INFILL
11.
Step 11.Connect three upper VE-31s where designated in diagram below using the attachment detail shown. Set V-LSW-CT-02 counter top onto completed frame.
VE-31
VE-31
VE-31
EXTRUSION WITHLOCKS
LOCK HORIZONTAL EXTRUSION BYUSING T- HANDLE TOOL
EXTRUSIONWITH LOCKS
T HANDLE LOCK
12.
V-LWS-CT-02
Step 12.Connect VE-40s to the VE-01s on the frame using the VE-16s. See attachment detail below. Connect the VE-40s using the VE-17s.
VE-1 VE-1
VE-17
VE-1
VE-1
VE-17
VE-40VE-40
EXTRUSION WITH LOCKS
LOCK HORIZONTAL EXTRUSION BYUSING T- HANDLE TOOL
T HANDLE LOCK
EXTRUSIONWITH LOCKS
6 6
6
6
13.
Step 13.Gently place V-LWS-CT-03 tabletop on completed frame.
V-LWS-CT-03
14.
Step 14.Slide seven lights onto clips and place into the middle channel of VE-53s and VE-44 as designated below using the attachment shown.
LIGHTLIGHT
LIGHTLIGHT
LIGHT
LIGHTLIGHT
LV1 Light
Light clip
1- Slide light clip onto the LIGHT.2-Then slide the LIGHT into the channel at an angleand then gently lower down.
LIGHT W/ CLIP
15.
check out these related products:
We continue to improve and modify our product range and reserve the right to vary the specifications without prior notice. All dimensions and weights quoted are approximate and we accept no responsibility for variance. E&OE. See Graphic Templates for graphic bleed specifications.
Redesign of this exhibit without approval by Nimlok may result in dangerous and unsafe structures. Nimlok disclaims any responsibility for redesigned exhibits it does not approve in writing. Parts and components such as panels and extrusions are manufactured to metric sizing.
velocity standard 01 velocity standard 02 velocity standard 03 velocity standard 04
velocity standard 05 velocity standard 06 velocity standard 07 velocity standard 08