Upload
others
View
64
Download
3
Embed Size (px)
Citation preview
V6000 Datasheet
Version: 0.3
Release Date: June 27, 2016
Specifications are subject to change without notice.
© 2016 Vango Technologies, Inc.
This document contains information that is proprietary to Vango Technologies, Inc.
Unauthorized reproduction of this information in whole or in part is strictly prohibited.
V6000 Datasheet
- 1 -
PLC-DS-013-EN
Vango Technologies, Inc.
Confidential
Revision History
Date Version Description
2016.04.30 0.1 Initial release
2016.11.21 0.2 Updated single power supply range from 9V~18V to 9V~15V
2017.06.27 0.3 Added serial number and updated format
V6000 Datasheet
- 2 -
PLC-DS-013-EN
Vango Technologies, Inc.
Confidential
General Description
The V6000 is a receiver (RX) integrated line driver, providing a high-current capability for driving the
low-impedance line applications. The fully-differential design can achieve a superior performance in terms
of MTPR (Multi-Tone Power Ratio) at 16 Vppd when 4 A peak current outputs. It also retains the bandwidth
and the linearity while operates at single power supply of 9V~15V and temperature range of -40 °C ~ +85
°C.
The V6000 contains a voltage-feedback TX amplifier and a programmable RX gain amplifier. Both of
the amplifiers are designed to deal with the high-swing signal. The V6000 is protected against Over
Temperature (OT) and Over Current (OC) by the built-in sensor. An internal-forced shutdown signal can be
used to set the device back to the initial state. Besides, the OC condition can be avoided once the alarm
alerts and is fed into the signal source. Via the SPI/I2C interface, the V6000 can be fully-controlled and
optimized by firmware configuration.
The V6000 is housed in a thermally-enhanced 40-pin QFN package.
Features
Supporting 4 A output driving capability
Accurate thermal sensor for Over
Temperature (OT) protection
Supporting built-in Over Current (OC)
protection
Programmable TX and RX gain
Single power supply range: 9V~15V
28 Vppd output under 18 V power supply
Zero-crossing detectors
Supporting SPI/I2C control interface
Package: 40-pin QFN EPAD
Operating temperature: -40 °C ~ +85 °C
Applications: Power Line Communication
(PLC)
V6000 Datasheet
- 2 -
PLC-DS-013-EN
Vango Technologies, Inc.
Confidential
Table of Contents
Revision History ..................................................................................................................... 1
General Description ................................................................................................................ 2
Features ................................................................................................................................. 2
Table of Contents ................................................................................................................... 2
Figure List .............................................................................................................................. 3
Table List ............................................................................................................................... 4
1. Electrical Characteristics ............................................................................................... 5
1.1. Absolute Maximum Ratings ....................................................................................... 5
1.2. Analog Specifications ............................................................................................... 5
1.3. Digital Interface Specifications .................................................................................. 6
1.4. SPI Timing Specifications .......................................................................................... 7
2. Pin Assignments ............................................................................................................ 9
3. Pin Descriptions .......................................................................................................... 11
4. System Block Diagram ................................................................................................. 13
5. Outline Dimensions ..................................................................................................... 14
V6000 Datasheet
- 3 -
PLC-DS-013-EN
Vango Technologies, Inc.
Confidential
Figure List
Figure 1-1 Timing Diagram .......................................................................................................................................... 8
Figure 4-1 System Block Diagram .......................................................................................................................... 13
Figure 5-1 Outline Dimensions ................................................................................................................................ 15
V6000 Datasheet
- 4 -
PLC-DS-013-EN
Vango Technologies, Inc.
Confidential
Table List
Table 1-1 Absolut Maximum Ratings ...................................................................................................................... 5
Table 1-2 Analog Specifications for General Characteristics ...................................................................... 5
Table 1-3 Analog Specifications for RX PGA ....................................................................................................... 6
Table 1-4 Analog Specifications for TX LD ........................................................................................................... 6
Table 1-5 Digital Interface Specifications ............................................................................................................ 6
Table 1-6 SPI Timing Specifications (SPI Mode 0) .......................................................................................... 7
V6000 Datasheet
- 5 -
PLC-DS-013-EN
Vango Technologies, Inc.
Confidential
1. Electrical Characteristics
1.1. Absolute Maximum Ratings
While the operating circumstance exceeding “Absolute Maximum Ratings”, it may cause the permanent
damage to the device.
Table 1-1 Absolut Maximum Ratings
Parameter Min. Typ. Max. Unit Conditions/Comments
Analog Power Supply(AVDD_PA) -0.3 +18 V
Analog Power Supply(AVDD33) -0.3 +4 V
Digital Power Supply(DVDD_IO) -0.3 +4 V
Storage Temperature -40 +125 ˚C
Operating Temperature -40 +85 ˚C
ESD 4000 V HBM
V CDM
Junction Temperature - 150 °C
Lead Temperature (Soldering, 10s) - 300 °C
1.2. Analog Specifications
All maximum and minimum specifications apply to the entire recommended operation range
(T = -40 °C ~ +85 °C, AVDD33 = 3.3 V ± 10%), unless otherwise noted. All typical specifications are at
TA = 25 °C and AVDD33 = 3.3 V ± 10%, unless otherwise noted.
Table 1-2 Analog Specifications for General Characteristics
Parameter Min. Typ. Max. Unit Conditions/Comments
Analog Power Supply(AVDD_PA) 9 12 15 V High voltage supply
Analog Power Supply(AVDD33) 2.97 3.3 3.63 V 3.3V supply
Temperature -40 85 °C
V6000 Datasheet
- 6 -
PLC-DS-013-EN
Vango Technologies, Inc.
Confidential
Table 1-3 Analog Specifications for RX PGA
Parameter Min. Typ. Max. Unit Conditions/Comments
Gain -18 0 18 dB 6dB per step
Noise 40 nV/Hz0.5
Distortion (Worst Harmonic) -80 dBc Fc = 1MHz, Vout=4Vppd
-70 dBc Fc = 2MHz, Vout=4Vppd
Input 30 V Differential peak-to-peak
Output 4 V Differential peak-to-peak
Table 1-4 Analog Specifications for TX LD
Parameter Min. Typ. Max. Unit Conditions/Comments
Gain 4 7
Distortion(Worst Harmonic) -55 dBc RL=10Ω, Vout=16Vppd
-50 dBc RL=4Ω, Vout=16Vppd
Input 4 V Differential peak-to-peak
Output 16 20 28 V Differential peak-to-peak
Quiescent Current 100 mA
1.3. Digital Interface Specifications
All maximum and minimum specifications apply to the entire recommended operation range
(T = -40 °C ~ +85°C, DVDD_IO = 3.3 V ± 10%), unless otherwise noted.
Table 1-5 Digital Interface Specifications
Parameter Min. Typ. Max. Unit Conditions/Comments
Digital Power Supply(DVDD_IO) 2.97 3.3 3.63 V
Digital IO, Output
Output High Voltage, VOH 2.4 V
Output Low Voltage, VOL 0.4 V
ISOURCE 4 mA
V6000 Datasheet
- 7 -
PLC-DS-013-EN
Vango Technologies, Inc.
Confidential
Digital IO, Input
Input High Voltage, VIH 2.0 3.63 V
Input Low Voltage, VINL -0.3 0.8 V
Internal Pull Resistance 22 k
1.4. SPI Timing Specifications
All maximum and minimum specifications apply to the entire recommended operation range
(T = -40 °C ~ +85 °C, DVDD_IO = 3.3 V ± 10%), unless otherwise noted.
Table 1-6 SPI Timing Specifications (SPI Mode 0)
Parameter Min. Max. Unit
tCYC SPI_CLK cycle time 8Ts ns
tPH SPI_CLK pulse high 3Ts ns
tPL SPI_CLK pulse low 3Ts ns
tDLY SPI_MISO delay time after SPI_CLK falling 2Ts 3Ts ns
tVLD SPI_MISO valid time after SPI_CLK rising 6Ts 7Ts ns
tSETUP SPI_MOSI setup time before SPI_CLK rising 2Ts ns
tHOLD SPI_MOSI hold time after SPI_CLK rising 2Ts ns
tCS_SETUP SPI_CS setup time before SPI_CLK rising 2Ts ns
tCS_HOLD SPI_CS hold time after SPI_CLK falling 2Ts ns
Note: Ts=1/Fs (Fs is the clock frequency of CLKIN input).
V6000 Datasheet
- 8 -
PLC-DS-013-EN
Vango Technologies, Inc.
Confidential
SPI_CLK
SPI_MOSI
SPI_MISO
SPI_CS
tSETUP
tHOLD
tDLY tVLD
tCS_SETUP
tCS_HOLD
tCYC tPH tPL
Figure 1-1 Timing Diagram
V6000 Datasheet
- 9 -
PLC-DS-013-EN
Vango Technologies, Inc.
Confidential
2. Pin Assignments
40-pin QFN
32
4 652 3 8
15
14
11
12
22
21
23
24
9
13
7
V6000
AVD
D33
RXIN
N
RXIN
P
PW
R_RD
Y
TXIN
P
CLKIN
ZCIN2
ZCOUT1
DVSS_IO
ZCIN1
RXOUTP
REXT
DVDD_IO
AVDD_PA
TXOUTP
SPI_
MIS
O
SPI_
CLK
SPI_
CS
ZCO
UT2
AVDD_PA
NC
TXIN
N
RXOUTN
16
31
10
NC
1N
C
AVDD_PA
TXOUTP
TXOUTN
TXOUTN
AVDD_PA
17
18
NC
NC
19
20
SPI_
MO
SI
GPIO
0
GPIO
1
TEST
NC
NC
25
26
27
28
29
30
33
34
36
35
37
38
39
40NC
NC
NOTE: The exposed thermal pad is connected to the ground.
V6000 Datasheet
- 10 -
PLC-DS-013-EN
Vango Technologies, Inc.
Confidential
V6000 Datasheet
- 11 -
PLC-DS-013-EN
Vango Technologies, Inc.
Confidential
3. Pin Descriptions
(Pin type: “O”=Output, “I”= Input, “P”=Power, “G”=Ground)
No. Mnemonic Type Description
1 NC NC
2 TXINP I Line driver differential positive input
3 TXINN I Line driver differential negative input
4 PWR_RDY O Power ready signal output
5 RXINP I Receiver amplifier differential positive input
6 RXINN I Receiver amplifier differential negative input
7 AVDD33 P Analog 3.3 V power
8 REXT I/O For external resistor connection
9 NC NC
10 NC NC
11 NC NC
12 AVDD_PA P Line driver high-voltage power
13 AVDD_PA P Line driver high-voltage power
14 TXOUTP O Line driver differential positive output
15 TXOUTP O Line driver differential positive output
16 TXOUTN O Line driver differential negative output
17 TXOUTN O Line driver differential negative output
18 AVDD_PA P Line driver high-voltage power
19 AVDD_PA P Line driver high-voltage power
20 NC NC
21 NC NC
22 TEST For test only
23 GPIO1 O General purpose output 1
24 GPIO0 O General purpose output 0
25 ZCOUT2 O Zero-crossing detector2 output
V6000 Datasheet
- 12 -
PLC-DS-013-EN
Vango Technologies, Inc.
Confidential
No. Mnemonic Type Description
26 SPI_CS I SPI chip select input. Used as I2C_SCL in proprietary I2C mode
27 SPI_MOSI I SPI slave input
28 SPI_MISO I/O SPI slave output. Used as I2C_SDA in proprietary I2C mode
29 SPI_CLK I SPI clock input
30 NC NC
31 NC NC
32 DVDD_IO P IO 3.3 V power
33 CLKIN I 24 MHz clock input
34 DVSS_IO G IO 3.3 V ground
35 ZCOUT1 O Zero-crossing detector1 output
36 ZCIN2 I Zero-crossing detector2 input
37 ZCIN1 I Zero-crossing detector1 input
38 RXOUTN O Receiver amplifier differential negative output
39 RXOUTP O Receiver amplifier differential positive output
40 NC NC
V6000 Datasheet
- 13 -
PLC-DS-013-EN
Vango Technologies, Inc.
Confidential
4. System Block Diagram
V6000
OverTemp
Sensor
ZeroCrossing
Detector
PowerOnReset
PGA
RX
TX
OverCurrent
Protection
LD
I2C/SPI
Interface
MISC
Figure 4-1 System Block Diagram
V6000 Datasheet
- 14 -
PLC-DS-013-EN
Vango Technologies, Inc.
Confidential
5. Outline Dimensions
V6000 Datasheet
- 15 -
PLC-DS-013-EN
Vango Technologies, Inc.
Confidential
Figure 5-1 Outline Dimensions