USER MANUAL - FURIOUS FPV ... How to set up Piggy OSD via Furious FPV FTDI Furious FPV FTDI is compulsory

  • View
    3

  • Download
    0

Embed Size (px)

Text of USER MANUAL - FURIOUS FPV ... How to set up Piggy OSD via Furious FPV FTDI Furious FPV FTDI is...

  • Please contact us if you need further assistance: Tech support: tech@furiousfpv.com Sales support: sales@furiousfpv.com Website: http://furiousfpv.com/

    PIGGY OSD FOR KISS FC

    USER MANUAL

    mailto:tech@furiousfpv.com mailto:sales@furiousfpv.com http://furiousfpv.com/

  • Specifications:

     Item name: Piggy v2

     Power input: 5V

     WxLxH : 23.5 x 23.5 x 2.5 mm

     Super light weight: 1.1 gr

     New chip use low power consumption and

    work better

     Compatible with all flight controllers that run

    KISS

     New design layout can fit with most of FPV

    Cam such as:

     Runcam Swift

     Runcam Swift 2

     Runcam Eagle

     Runcam Rotor Riot

     Runcam Owl Plus

     Foxeer HS1177

     Foxeer Night Wolf

     Foxeer Arrow

     Foxeer Monster

    Other camera:

     Lumenier CM-650 Mini – 650 TVL Camera

     TBS Zerozero V2

  • Diagram illustrates connections of Piggy V2 with KISS FC

    *Note: You need Piggy OSD for KISS FC version or you can flash firmware Piggy V2 BetaFlight to

    Kiss FC with FTDI

     Using VTX Tramp HV

     Using VTX TBS Unify Pro

  •  Using VTX FX FX799T

  • How to set up Piggy OSD:

    - How to set up OSD with TX:

    To access the in-built OSD menu in MW-OSD, disarm your quadcopter first.

     THROTTLE MIDDLE

     YAW RIGHT

     PITCH FULL

    To navigate through menu in the OSD:

     PITCH/ROLL sticks are used to

    navigate

     YAW stick is used to adjust /

    change values

    OSD Menu Index:

     Voltage (Display voltage on/off, Adjust Voltage, Voltage alarm, Cells)  RSSI (Display RSSI on/off etc)  Current (Display Amp on/off, Adjust Amps)  Advanced (Unit – Metric…)  Display (On/Off switches for Horizon, Sidebars, Scrolling bars, Throttle, GPS Coordinates,

    Sensors, Gimbal, Map Mode)  Advanced (Unit, VREF, etc.)  Alarms (Distance, altitude, timer …)  Statistics (Fly time, Maximum Distance, Max Altitude, Max Speed, Flying time)

  • - How to set up Piggy OSD via Furious FPV FTDI Furious FPV FTDI is compulsory in order to set up Piggy V2

    Tool FTDI : https://goo.gl/Th6x25

    Step 1: Download Furious FPV FTDI driver and MW-OSD software

    *Note: If you use Furious FPV FTDI, you can install the next steps

    Download: MW-OSD GUI R1.6

    Download driver here: https://goo.gl/N9aZCN

    Step2 : You must extract the zip archive into a temporary directory. DO NOT attempt to double- click or run any of the files until you have extr acted them

    Step 3: Open the temporary directory and run the appropriate executable

     If you have a 64-bit operating system, you should run pololu-cp2102-setup-x64.exe

     If you have a 32-bit operating system, you should run pololu-cp2102-setup-x86.exe

    https://goo.gl/Th6x25 https://codeload.github.com/ShikOfTheRa/scarab-osd-gui/zip/master https://goo.gl/N9aZCN

  • Step 4: Same below picture

  • Step 5: Right-click My Computer icon and select Manage. Connect FTDI tool to computer via USB and click Device Manager. In the Ports (COM & LPT) appearances Silicon Labs CP210x USB to UART Bridge then your installers completed successfully

    *Note: If your computer has not java application, You need to follow steps 6–10 for you connect to your computer

    Step 6: Download and run Java application. Then, follow the same below picture

  • How to set up OSD with MW OSD:

    Step 1: Connect Piggy V2 to the computer via FTDI tool

    *Note: Remove everything and only use piggy module when you connect to FTDI tool

  • Step 2: Open the application MW_OSD_GUI

    Step 3: Choose the COM port on MWOSD R1.6 to connect your FTDI with the computer and wait until MWOSD load complete. You can turn on/off functions that you want to show on your goggles/display. Note: Click Device Manager and choose the correct COM same as in the Ports (COM & LPT)

    *Note: If you want to show current or voltage on the default screen, you turn on Use FC main voltage and Use FC amperage same below picture:

  • Step 4: Click Write to write your OSD configuration to Piggy V2

    Flash firmware Piggy v2 Betaflight to KISS FC/Raceflight FC and

    vice versa.

    Firmware: https://goo.gl/pFhp8z

    Xloader: https://goo.gl/IKJveN

    After installing driver and running Xloader to flash firmware, connect FTDI tool with Piggy v2 as instructed and select as below:

    Step 1: Select Firmware on your computer

    Step 2: Select Duemilanove/Nano (ATmega328)

    Step 3: Select Com Port with Baudrate 57600

    Step 4: Click Upload and wait finish process

    https://goo.gl/pFhp8z

  • Thanks for using our product