UpholsteredGaslift Bed Base

A S S E M B LY G U I D EV7

F O R Y O U R S A F E T Y

Lift, don’t drag. This protects your floor and product.

Avoid loose screws. Tighten fixtures every few months.

Assembly requires 2 people. It's always easier with a

friend.

Contact our support online or call 1300 027 672.

Check the assembly guide for required components.

?

Assembling this product on a soft surface protects its

finish.

ComponentsBefore you get started, check you have all of the pieces below.If anything’s missing, we’ll sort it out right away. Simply visit:www.brosa.com.au/pages/product-return-and-parts-request

Headboard x 1 Right Sideboard x 1

①

②

Hardware

A x 2(M8 x 80/40)

B x 4(Ø8)

C x 2(M8)

D x 1(M8)

E x 8(M8 x 60)

F x 8(M8)

G x 1(M8)

H x 1 I x 1

③ ④

⑤

⑥

⑦

⑧

Left Sideboard x 1

Footboard x 1

Floor Board x 2

Wooden Support Bar x 3

Slat Set x 1

Mattress Retainer x 2

Handle x 2⑨

Loosen the pre-attached bolts on both sideboards ② ③ and the footboard ④ using the Allen key I but do not remove them.

Step 1

I x 1

②

③④

I

I

Hook the brackets to the bolts. Screw the bolts with the Allen key I but do not tighten them yet.Step 2

I x 1

I

I

②

③④

①

Adjust and make sure the frame formed in Step 2 is aligned perfectly and then tighten all bolts with the Allen key I.

Step 3

I x 1

I

Unscrew and remove the nut from the threaded rod of the gas lift arm. Keep the removed nut for the following assembly. Repeat this for the other side.

Step 4

Lift the gas lift arm and the gas lift strut so that the threaded rod of the arm can fit into the hole of the strut.

Step 5

Secure the structure formed in Step 5 using the nut removed in Step 4 with the spanner G. Repeat the process for the other side.

Step 6

G x 1

G

Fit the wooden support bars ⑥ into the slots.Step 7

⑥

Place the floor boards ⑦ on top of the wooden support bars.Step 8

⑦

Unfold the slat set ⑤ to make a full-size slat set.Step 9

⑤

Place the slat set on a level protected surface, making sure the underside is facing you.Fit a flat washer B to a long bolt A. Insert the bolt from one side of the middle bars, making sure it protrudes from the other side. Fit a flat washer B and a nut C to the bolt from the other side. Tighten the nut with the spanner D.

Step 10

A x 2

B x 4

C x 2

D x 1

A

B

BC

D

Flip the slat set the right way up and align it with the holes on the gas lift arms.Insert bolts E into corresponding holes on the slat set frame. Attach flange nuts F onto the bolts from the other side and fix them with the screwdriver H and spanner G.

Step 11

E x 8

F x 8

G x 1

H x 1

E

F

G

H

Attach both handles ⑨ to the end of the slat set frame.Step 12

⑨

With a friend, push the slats down. It requires a fair amount of strength because there isn’t a mattress on the slats to add weight yet.

Step 13

The rubber blocks on the mattress retainer ⑧ can be rotated into different positions. Rotate both rubber blocks to be horizontally longer. Repeat this for the other retainer.Clip the mattress retainers to proper spots on the front end of the slat set frame from inside as shown in the diagram below.

Step 14

⑧

Enjoy your new Gaslift Bed Base!Step 15

1. Please do NOT sit on the bed frame without a mattress.

Warning

2. The maximum loading weight for the bed base is 350kg. Please do NOT exceed the weight limit.

MAX.350 KG

3. Please always use the handles to lift and lower the bed frame to avoid trapping your fingers. Always use both hands.

4. To make sure that the gas lift mechanism performs properly and can be used for a longer time, choose a mattress/topper under 70kg.

<70KG

5. Do not allow children to play around the bed when it is lifted up.

1. If you are using a mattress higher than 24cm, your mattress might go against your bedhead while you lift it up and stop your gas lift mechanism from locking into place.

2. Moving your bed base a bit further away will give your high mattress more space to move.

Troubleshooting

>24cm

We hope you enjoy your new piece of Brosa furniture. Correct maintenance will increase its durability and keep it looking beautiful for longer. Follow these tips as a guide.

1. Furniture should be assembled according to our Assembly Guides. You can find them at support.brosa.com2. Store furniture in dry, ventilated rooms on tough flooring.3. Plump cushions with your hands to restore its shape after transportation.4. Keep furniture away from radiators, air conditioners and extreme temperatures (at least 30cm distance).5. Protect your furniture from direct sunlight, which can discolour fabric and dry out leather.6. We recommend dispersing weight evenly across the surface, rather than repeatedly lying in the same spot.7. Don’t jump or apply sudden force to the furniture. This may damage the frame or suspension.8. When moving furniture from one place to another, lift don’t drag.9. Take caution with pets around furniture. Their claws and teeth may cause damage.10. Avoid using cleaning products containing harsh chemicals or oil dissolving solvents.11. Vacuum crevices of furniture on a low suction when needed.

Important points

1. Moisture Our products are made using wood and other materials that can be sensitive to moisture. We recommend keeping furniture in an environment with 45-60% relative moisture and at 10-25°C.2. Sunlight After time the fabric colour will change slightly, which is a natural effect. To reduce this process, keep furniture out of direct sunlight.3. Wear and Tear Using furniture for a long time will result in slight material changes. Leather will develop character and markings, while some fabric folds may appear.

User Recommendation

4. Pilling Through regular use, the surface of natural fibre fabric can twist and form tiny balls – this is known as pilling. It is an inherent feature of this particular type of fabric and can be caused by environmental factors such as humidity or friction between two fabrics. It can be easily removed with a depiller and should disappear after 3-4 applications.5. Storage Ensure furniture stands on an even surface. This ensures stability and will prevent creaking or damage to the piece.6. Felt Pads We recommend attaching felt pads to the bottom of furniture legs. This prevents squeaking and protects your floor from scratches.7. Fabric Variation There may be differences and very slight variations between fabrics. The dyeing process means there isn’t an absolute guarantee it will match the sample’s colour perfectly.8. Clothing and Accessories Jeans and other dark clothing may leave stains or marks on furniture. Take extra care when wearing clothing that is new or not pre-washed. Also be careful wearing clothes with sharp decorative elements, as it may damage the fabric or leather.9. Leather Leather is a natural product, with unique, one-of-a-kind features. Each piece varies slightly.10. Softness Furniture tends to soften after the first few months of use. This is a normal process. Parts of the furniture that are sat on more frequently will become softer than others.