Ultrasonic Scaler QuickStart Guide: Scaler Ultrasonic Scaler QuickStart Guide: 1. Press S button to
Ultrasonic Scaler QuickStart Guide: Scaler Ultrasonic Scaler QuickStart Guide: 1. Press S button to

Ultrasonic Scaler QuickStart Guide: Scaler Ultrasonic Scaler QuickStart Guide: 1. Press S button to

  • View
    1

  • Download
    0

Embed Size (px)

Text of Ultrasonic Scaler QuickStart Guide: Scaler Ultrasonic Scaler QuickStart Guide: 1. Press S button to

  • OFF

    ON

    ZERO MAX

    Ultrasonic Scaler QuickStart Guide:

    1. Press S button to turn ON the Scaler.

    2. Tip Working mode:

    3. Select scaler function:

    4. Water regulation:

    5. Foot Pedal Control:

    6. Cleaning:

    Scaler

    Comprehensive cleaning function:

    The cleaning function can be started by pressing C. Water or disinfectant cleans the water line and handpiece. The cleaning cycle stops automatically after 80 seconds.

    With every push of the S button, the function toggles from: Scaling with water Dry mode: scaling without water Irrigation mode: just water, no scaling

    The unit is in standby mode when the power cord is connected and the green LED is illuminated.

    or or

    100 %70 %40 %

    Depress the foot control pedal in the leftmost position and adjust the water flow with the control ring on the scaler handpiece until the water is dripping.

    The scaler is activated when the foot control pedal is pressed down. The power is regulated from left/ZERO to right/MAX within the chosen working mode. In ZERO position there are two functions: a) irrigation with no scaling power: hold the footpedal

    down. b) diagnostic light: press the footpedal once.

    1

    1

    2

    2

    3

    4 3

    4

    Choose the correct working mode that is marked on the base of each tip by pressing the corresponding working mode button on the keypad:

    7. Push the S button for 3 seconds to turn the scaler OFF.

  • 1.

    4.

    2.

    5.

    3.

    1. Consult a qualified technician to install to water supply if applicable. 2. Connect the foot control pedal cable to the foot control pedal and to the rear of the unit. 3. Connect the power cord to the unit and the AC power outlet.

    6. See Section 4 in the owner’s guide for Operation Instructions.

    4. Fill the medicament bottle with water or medicament solution. Screw the bottle connector cap onto the bottle and push it onto the connector on the left side of the unit. When removing the bottle, press first the depressurization button beside the connector. 5. Gently slide a handpiece grip onto the scaler handpiece. Place the scaler tip in the torque wrench and use the torque wrench to screw the scaler tip clockwise onto the scaler handpiece. Tighten until the resistance causes the torque wrench to begin to slip.

    NOTE! Before installing and using the device please read the owner’s guide.

    6.b.

    Installation

    P/ N

    2 0

    0 0

    4 49

    9A

    coltene.com

    Coltène/Whaledent Inc. 235 Ascot Parkway Cuyahoga Falls, OH 44223 / USA Tel. USA & Canada + 1 800 221 3046 + 1 330 916 8800 Fax +1 330 645 8704 info.us@coltene.com

    Coltène/Whaledent AG Feldwiesenstrasse 20 9450 Altstätten / Switzerland Tel. +41 (0)71 757 53 00 Fax +41 (0)71 757 53 01 info.ch@coltene.com

    Coltène/Whaledent GmbH + Co. KG Raiffeissenstrasse 30 89129 Langenau / Germany Tel. +49 (0)7345 805 0 Fax +49 (0)7345 805 201 info.de@coltene.com

View more