ULTRASONIC CASE CLEANER-2
Before using the RCBS Ultrasonic Case Cleaner-2, read these instructions carefully to fully learn how to safely operate the related equipment. Failure to properly operate the related equipment can result in severe personal injury and/or equipment damage.
If you have any questions while assembling or operating this tool, Call us at 1-800-379-1732 (U.S. or Canada)
Monday Friday 5:00 a.m. 5:00 p.m. Pacific Time (hours may vary)
Or email us at email@example.com
This instruction manual contains specific safety and operating information.It should be considered a permanent part of your equipment and remain with the equipment at all times for easy reference.
Reloading is an enjoyable and rewarding hobby that can be conducted safely. But, as with any hobby, carelessness or negligence can make reloading hazardous. This product has been designed from the beginning with the users safety in mind. When reloading, safety rules must be followed. By observing these rules, the chance of a hazardous occurrence causing personal injury or property damage is minimized.
KEEP AWAY FROM CHILDREN!This device is not intended for use by individuals with restricted physical, sensory or mental capacities or those with a lack of experience and/or knowledge, including children, unless they are supervised by an individual who is responsible for their safety or have received training in operating the device. Please store the RCBS Ultrasonic Case Cleaner-2 where it is out of the reach of children. Keep all packing material out of reach of children.
To prevent life-threatening electric shock, please observe the following:
Danger of electric shock! Do not use while bathing. Never immerse the device or power cord in water or other liquid.
Danger of electric shock! Never touch the power plug with wet hands, especially when inserting or removing the plug.
Danger of electric shock! If the unit has fallen in water during operation, do not touch the unit. Remove the power plug from the socket first.
Danger of electric shock! Do not spray water or liquid over the device. When removing the cord from the socket, grab the power plug, not the cord. Protect the power cord from damage. If there is damage to the power plug, cord, housing, or other parts of the device, do not use. Disassembly of this device should only be performed by qualified professionals. When not in use always remove the power cord from the socket. Use of a GFCI with a rated trip current of no more than 30mA should be used to provide protection
against electric shock. The installation of a GFCI circuit should only be carried out by a qualified electrician.
GENERAL Use all equipment as the manufacturer recommends. Study the instructions carefully and become
thoroughly familiar with the operation of the product. If you do not have written instructions, request a copy from the equipment manufacturer.
Do not take short cuts. Attempting to bypass established procedures is an invitation to an accident.
Observe good housekeeping in the reloading area. Keep tools and components neat, clean and orderly. Promptly and completely clean up primer and powder spills.
Reload only when you can give your undivided attention. Do not reload when fatigued or ill, or under the influence of medications or alcohol.
Develop a reloading routine to avoid mistakes which may prove hazardous. Do not rush - load at a leisurely pace.
Always wear adequate eye protection to protect your eyes from flying particles. You assume unnecessary risk when reloading without wearing safety glasses.
LOADING DATA Use only laboratory tested reloading data. We highly recommend the current SPEER Reloading
OBSERVE ALL WARNINGS ABOUT THE USE OF MAXIMUM LISTED LOADS.
RECORD KEEPING Keep complete records of reloads. Apply a descriptive label to each box showing the date
produced, and the primer, powder and bullet used. Labels for this purpose are packed with SPEER bullets.
Never attempt to guess at the identity of your ammunition.
Because RCBS has no control over the choice of components, the manner in which they are assembled,the use of this product, or the firearms in which the resulting ammunition may be used, we assume
no responsibility, expressed or implied, for the use of ammunition reloaded with this product.
The RCBS Ultrasonic Case Cleaner-2 is designed to clean metallic surfaces. Ultrasonic cleaners work by creating millions of tiny air bubbles inside the liquid by high frequency vibration. The air bubbles burst inside the liquid on the surface of the submerged items and shake off the debris to achieve the cleaning effect. When used with the RCBS Ultrasonic Case Cleaning Solution, your cases will be clean and free of carbon fouling, lubricants, and debris on the exterior and interior, of your cartridge cases. Purified or distilled water has the same cleaning effect as regular tap water for ultrasonic cleaning. Therefore using tap water is sufficient. However, your tap water may contain minerals and solids, which may cause spots on surfaces. When cleaning silver or copper items where oxidation and carbon fouling has darkened the items, special cleaning solutions such as RCBS Ultrasonic Case Cleaning Solution needs to be added to the water to remove the oxidation. The RCBS Ultrasonic Cleaner-2 comes equipped with a special degassing function. When cleaning solutions are added to the water in the tank, droplets of solution will form which take time to dissolve in the water. The solution may also form many small air bubbles on the tank walls. The droplets and bubbles act as a buffer or insulator, which may reduce the cleaning effectiveness. The degassing function will aid in dissipating the bubbles and droplets, which will improve the cleaning efficiency. The degas function will operate for 2 minutes, which is generally enough time to dissipate the droplets and bubbles.
To order the cleaning solution or find out more information, contact RCBS or visit our website (www.rcbs.com).
Tank size: 12.7 x 8.1 x 3.9/ 32.3 x 20.5 x 9.9 cm Tank capacity: 1.6 gal./ 6.0 L Longest item that can fit inside the tank is 13.4/34.0 cm. 3-color LED display. 1 to 30-minute full range timer 5 pre-set temperature settings. Temperature display in C or F. Ceramic heater and overheat protector Solution usage timer (Solution time remains in memory even when electricity is switched off). 2 Industrial grade ultrasonic transducers, 2 ceramic heaters. Industrial grade IC. Moisture-proofed PCB with cooling fan. Drainage valve.
Never attempt to clean loaded cartridges or primed cases. Never turn heater on when there is no fluid in tank. Use drain valve to empty tank. Never submerge the Ultrasonic Cleaner in water or any other liquid in an attempt to clean the unit. Do not spray Ultrasonic Cleaner with water or other fluids. Never use unit if power cord becomes damaged. Never attempt to disassemble Ultrasonic Cleaner. Always use on a flat level surface. Do not overfill the unit by exceeding the Max Fill mark located inside the tank. Always disconnect power cord before filling and when draining tank. Only use water or recommended cleaning solutions, such as the RCBS Case Cleaning Solution. If Ultrasonic Cleaner has been in operation for 45 min. allow 10 min. time before next use, to prolong life of unit. Always use the Basket when cleaning articles to protect stainless steel tank. Allow for adequate room around Ultrasonic Cleaner to allow for cooling. Do not store items next to unit while in use.
Keep side cooling fans and vents clear of any obstructions (rags, bags, boxes, etc.). Always unplug unit when not in use.
WARNING Care should be used when operating electrical appliances in wet areas or around water. Always unplug unit when filling or draining tank. Operating unit on a GFCI outlet is highly recommended.
Cartridge Cases Using specialized cleaning solutions; such as the RCBS Case Cleaning Solution. Gun Parts Using specialized cleaning solutions; such as the RCBS Weapons Cleaning Solution. Jewelry Using water only. Eye Glass frames Using water only. Tools Using specialized cleaning solutions
Many more items can be cleaned using the RCBS Ultrasonic Case Cleaner-2. If using other than water, ensure you follow the manufacturers recommended usage for various material types.
Refer to the list below to identify parts as you carefully unpack your new Ultrasonic Case Cleaner-2:
ITEM NO. DESCRIPTION PART NUMBER
1 Ultrasonic Cleaner-2
2 Lid 7187095
3 Basket Frame
5 Stainless Steel Tub - small
6 Power Cord 7187098
7 Drain Hose 7187097
DISPLAY and KEYPAD
1. Digital Timer Display - Displays the set run time. 2. Water Temperature Indicator - Solid green light indicates that the
water temperature is 0-30% of the set temperature. Solid orange light indicates that the water temperature is 30-60% of the set temperature. Solid red light indicates that the water temperature is 60-90% of the set temperature. Flashing red light indicates that the water temperature is close to the set temperature. All solid lights indicate that the water temperature is at the set tempe