Ult REL Output Analog Modules 1734-In002 En

7/25/2019 Ult REL Output Analog Modules 1734-In002 En

1/24

Publication1734-IN002C-EN-E - Apri l 2005

Installation Instructions

POINT I/O 2 Current Output and 2 VoltageOutput Analog Modules

Catalog Numbers 1734-OE2C and 1734-OE2V, Series C

Inside

For This Topic See Page

Important User Informat ion 2

Prevent ing Electrostat ic Discharge 3

Environment and Enclosure 4

Before You Begin 5

Ident ify M odule Components 5

Install the M ount ing Base 6

Install the M odule 7

Install the Removable Terminal Block (RTB) 8

Remove a M ount ing Base 9

Communicate w ith Your M odule 11

W ire the M odule 12

Troubleshoot w ith Indicators 15

Nort h Am erican Hazardous Location A pproval 18

European Hazardous Locati on Approval 19

Specifications 20


2/24

2 POINT I/ O 2 Current Output and 2 Voltage Output Analog M odules

Publication1734-IN 002C-EN-E - Apri l 2005

Important User Information

Solid state equipment has operational characteristics differing from those ofelectromechanical equipment. Safety Guidelines for the Appl ication, Install ation andM aintenance of Solid State Controls(Publicatio n SGI-1.1 availabl e f rom your l ocal Rockw ellAutomation sales off ice or online at http:// l i terature.rockw ellautomation.com) describessome important diff erences betw een solid state equipment and hard-w iredelectromechanical devices. Because of t his diff erence, and also because of t he w ide varietyof uses for solid state equipmen t, all persons responsible for applying thi s equipment mustsatisfy themselves that each intended application of this equipment is acceptable.

In no event w ill Rockw ell Aut omati on, Inc. be responsible or liable for indirect or

consequential damages resulting f rom the use or application of this equipment .The examples and diagrams in t his manual are included solely for i llustrat ive purposes.Because of the many variables and requirements associated w ith any particular installat ion,Rockw ell Aut omati on, Inc. cannot assume responsibilit y or liability f or actual use based onthe examples and diagrams.

No patent l iabil i t y is assumed by Rockw ell Aut omation, Inc. w ith respect to use ofinformation, circuits, equipment, or software described in this manual.

Reproduction of t he contents of this manual, in w hole or in part, w ithout w ritten permission

of Rockw ell Aut omati on, Inc., is prohibited.Throughout t his manual, w hen necessary, w e use notes to make you aware of safetyconsiderations.

WARNING Identifies information about practices or circumstances that can cause an explosion in ahazardous environment, w hich may lead to personal injury or death, property damage, oreconomic loss.

IMPORTANTIdentifi es information t hat is critical for successful application and understanding of t heproduct.

ATTENTION Identif ies informat ion about practices or circumstances that can lead to personal injury ordeath, property damage, or economic loss. Attentions help you:

identi fy a hazard avoid a hazard recognize t he consequence

SHOCK HAZARD Labels may be located on or inside t he equipment (e.g., drive or motor) to alert peopl ethat dangerous voltage may be present.

BURN HAZARD Labels may be located on or inside t he equipment (e.g., drive or motor) to alert peopl ethat surfaces may be dangerous temperatures.


3/24

POINT I/ O 2 Current Output and 2 Voltage Output A nalog M odules 3

Publication 1734-IN 002C-EN-E - Apr il 2005

ATTENTION Preventing Electrostatic DischargeThis equipm ent is sensitive to electrostatic

discharge, w hich can cause internal dam age and

affect norm al operation. Follow these guidelines

w hen you handle this equipm ent:

Touch a grounded object to discharge

potential static.

W ear an approved grounding w riststrap. D o not touch connectors or pins on

com ponent boards.

D o not touch circuit com ponents inside the

equipm ent.

If available, use a static-safe w orkstation.

W hen not in use, store the equipm ent in

appropriate static-safe packaging.


4/24



ATTENTION Environment and Enclosure

This equipm ent is intended for use in a Pollution

D egree 2 industrial environm ent, in overvoltage

Category II applications (as defined in IEC

publication 60664-1), at altitudes up to 2000 m eters

w ithout derating.

This equipm ent is considered G roup 1, Class A

industrial equipm ent according to IEC/CISPR

Publication 11. W ithout appropriate precautions,

there m ay be potential difficulties ensuringelectrom agnetic com patibility in other environm ents

due to conducted as w ell as radiated disturbance.

This equipm ent is supplied as open type

equipm ent. It m ust be m ounted w ithin an enclosure

that is suitably designed for those specific

environm ental conditions that w ill be present and

appropriately designed to prevent personal injuryresulting from accessibility to live parts. The interior

of the enclosure m ust be accessible only by the use

of a tool. Subsequent sections of this publication

m ay contain additional inform ation regarding

specific enclosure type ratings that are required to

com ply w ith certain product safety certifications.

See N EM A Standards publication 250 and IEC

publication 60529, as applicable, for explanations of

the degrees of protection provided by different

types of enclosure. Also, see the appropriate

sections in this publication, as w ell as the

Allen-Bradley publication 1770-4.1 (Industrial

Autom ation W iring and G rounding G uidelines), for

additional installation requirem ents pertaining to

this equipm ent.


5/24



Before You Begin

You can use these Series C m odules w ith D eviceN et and PRO FIBU S

adapters. If you are using RSLogix 5000 softw are, version 11 orhigher, you can also use the Series C m odules w ith ControlN et and

Ethernet adapters.

Identify Module Components

U se the figure to identify the external features of the m odules.

Analog

Volta

ge

Outp

ut

Mod

ule

Status

Netw

ork

Status

NOD

E:

0

1

The w iring base assembly includes t erminal base, 1734-TB or 1734-TBS,

43931

Interlocking

Side Pieces

DIN Rail

Locking

Screw

(orange) Removable Terminal Block (RTB)

Slide-in W ritable Label

Insertable I/O M odule

Module

WiringDiagram

M ounting Base

RTB Removab le Handle

Module

Locking

Mechanism

Mechanical

Keying(orange)

w hich consists of mounting base, 1734-M B, and removable terminal block,1734-RTB or 1734-RTBS.


6/24



Install the Mounting Base

To install the m ounting base on the D IN rail, proceed as follow s.

1. Position the m ounting base vertically above the installed units

(adapter, pow er supply, or existing m odule).

2. Slide the m ounting base dow n to m ake the interlocking side

pieces engage the adjacent m odule or adapter.

3. Press firm ly to seat the m ounting base on the D IN rail.

The m ounting base w ill snap into place.

ATTENTION PO IN T I/O is grounded through the D IN rail to

chassis ground. U se zinc-plated, yellow -chrom ated

steel D IN rail to assure proper grounding. The use

of D IN rail m aterials (e.g., alum inum , plastic, etc.)

that can corrode, oxidize, or are poor conductors

can result in im proper or interm ittent grounding.

Secure D IN rail to m ounting surface approxim atelyevery 200 m m .

ATTENTION D o not discard the end cap supplied w ith an

adapter or com m unication interface m odule.

U se this end cap to cover the exposed

interconnections on the last m ounting base on theD IN rail. Failure to do so could result in

equipm ent dam age or injury from electric shock.


7/24



Install the Module

Install the m odule before or after base installation. M ake sure that

you:

correctly keyed the m ounting base before installing the

m odule into the m ounting base

positioned the m ounting base locking screw horizontal w ithreference to the base

To install the m odule proceed as follow s.

1. U sing a bladed screw driver, rotate the keysw itch on the

m ounting base clockw ise until the num ber required for the

type of m odule you are installing aligns w ith the notch in the

base.

2. M ake certain the D IN rail locking screw is in the horizontal

position.

You cannot insert the m odule if you have unlocked the

locking m echanism .

3. Insert the m odule straight dow n into the m ounting base andpress to secure.

The m odule w ill lock into place.

WARNING W hen you insert or rem ove the m odule w hilebackplane pow er is on, an electrical arc can occur.

This could cause an explosion in hazardous

location installations.

Be sure that pow er is rem oved or the area is

nonhazardous before proceeding. Repeated

electrical arcing causes excessive w ear to contacts

on both the m odule and its m ating connector. W orn

contacts m ay create electrical resistance that can

affect m odule operation.


8/24



Install the Removable Terminal Block (RTB)

A rem ovable term inal block com es w ith your w iring base assem bly.

To rem ove, pull up on the RTB handle. You can now rem ove them ounting base and replace as necessary w ithout rem oving any of the

w iring. To reinsert the rem ovable term inal block, proceed as follow s.

1. Insert the end opposite the handle into the base unit.

This end has a curved section that engages w ith the w iring

base.

2. Rotate the term inal block into the w iring base until it locks

itself in place.

3. If an I/O m odule is installed, snap th e RTB handle into place

on the m odule.

WARNING W hen you connect or disconnect the rem ovable

term inal block (RTB) w ith field-side pow er

applied, an electrical arc can occur. This could

cause an explosion in hazardous location

installations.


nonhazardous before proceeding.


9/24



Remove a Mounting Base

To rem ove a m ounting base, you m ust rem ove any installed m odule,

and the m odule installed in the base to the right. Rem ove therem ovable term inal block, if w ired.

1. U nlatch the RTB handle on the I/O m odule.

2. Pull on the RTB handle to rem ove the rem ovable term inal

block.

3. Press on the m odule lock on the top of the m odule.

4. Pull on the I/O m odule to rem ove from the base.

WARNING W hen you connect or disconnect the rem ovable

term inal block (RTB) w ith field-side pow er

applied, an electrical arc can occur. This could

cause an explosion in hazardous location

installations.


nonhazardous before proceeding.

WARNINGW hen you insert or rem ove the m odule w hile

backplane pow er is on, an electrical arc can occur.


location installations.


nonhazardous before proceeding. Repeated

electrical arcing causes excessive w ear to contacts

on both the m odule and its m ating connector. W orn

contacts m ay create electrical resistance that canaffect m odule operation.


10/24

10 POINT I/ O 2 Current Output and 2 Volt age Output Analog M odules


5. Repeat steps 1, 2, 3, and 4 for the m odule to the right.

6. U se a sm all-bladed screw driver to rotate the orange, baselocking screw to a vertical position.

This releases the locking m echanism .

7. Lift straight up to rem ove.


11/24

POINT I/ O 2 Current Output and 2 Volt age Output Analog M odules 11


Communicate with Your Module

PO IN T I/O m odules send (consum e) and receive (produce) I/O

m essages. You m ap these m essages into the processors m em ory.

These m odules produce 2 bytes of input data (scanner Rx) (fault

status). These m odules consum e 4 bytes of output data (scanner Tx).

Message size: 2 Bytes

15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00

Produces

(scanner Rx)

High Byte - Channel 1 St atus Low Byte - Channel 0 Stat us

Not used H

C

A

L

C

A

C

M

C

F

Not used H

C

A

L

C

A

C

M

C

F

Where:

CF = Channel Fault st atus; 0 = no error, 1 = faultCM = Calibrati on M ode; 0 = normal, 1 = calibration mode

HCA = High Clamp A larm ; 0 = no error, 1 = fault

LCA = Low Clam p Alarm ; 0 = no error, 1 = fault

Message size: 4 bytes

15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00

Consumes

(scanner Tx)

Output Channel 0 High Byte Output Channel 0 Low Byte

Output Channel 1 High Byte Output Channel 1 Low Byte


12/24



Wire the Module

WARNING If you connect or disconnect w iring w hile the

field-side pow er is on, an electrical arc can occur.


location installations. Be sure that pow er is

rem oved or the area is nonhazardous before

proceeding.

1734

OE2C

NODE:

0

1

43962

1734-OE2C POINT I/O 2 Current Output Analog Module

M odule Status

Network Status

Status of Output 0Status of Output 1

Output 0 Connection 0 1 Output 1 Connection

5 CChas Gnd = Chassis Ground

C = Common

V = Supply

3 Chas GndChas Gnd 2

C 4

V 6 7 V

Module

Status

Network

Status

4-20mA

Analog

Output


13/24



Channel CurrentOutput

ChassisGround

Common Supply

0 0 2 4 6

1 1 3 5 7

12/ 24V dc pow er is provided by the internal f ield pow er bus.

CurrentOutputDevice

CurrentOutputDevice

2-wire4-wire

ac or dc

43964

Out = Output Channel

Chas Gnd = Chassis Ground

C= Common

V = 12/ 24V dc supply

0 1

32

Out0

Out1

ChasGnd

ChasGnd

54C C

76

VV

1734-OE2C POINT I/O 2 Current Output Analog Module


14/24



43963

M odule Status

Netw ork Status

Status of Output 0

Status of Output 1

Output 0 Connection 0

Chas Gnd 2

C 4

V 6

5 C

7 V

Chas Gnd = Chassis g roundC = Comm onV = Supply

1734-OE2V POINT I/O 2 Voltage Output Analog Module

3 Chas Gnd

1734

OE2V

NODE:

0

1

1 Output 1 Connection

Module

Status

Network

Status

Analog

Voltage

Output

Out 0 Out 1

ChasGndChasGnd

C C

VV

VoltageOutput

43965

3

5

7

0 1

2

4

6

VoltageOutput

1734-OE2V POINT I/O 2 Voltage Output Analog Module

Out = Output channelChas Gnd = Chassis GroundC = CommonV = 12/24V dc supply


15/24



Troubleshoot with Indicators

U se the status indicators and tables to troubleshoot your m odule.

Channel Voltage Output Chassis Ground Common Supply0 0 2 4 6

1 1 3 5 7

12/24V dc pow er is provided by the internal f ield pow er bus.

M odule Status

Netw ork Status

1734-OE2C

POINT I/O 2 Current

Output Analog Module

NODE:

0

1

43962

ModuleStatus

NetworkStatus

4-20mAAnalogOutput

Status of Output 0

Status of Output 1

1734-OE2V

POINT I/O 2 Voltage

Output Analog Module

M odule Status

Netw ork Status

NODE:

0

143963

ModuleStatus

Network

Status

AnalogVoltageOutput

Status of Output 0

Status of Output 1


16/24



Indication Probable CauseModule Status

Off No pow er is appl ied to device.

Green Device is operat ing normal ly.

Flash ing Green Device needs commission ing due to conf igura t ion missing,

incomplet e, or incorrect.

Flashing Red Recoverable fault is present .Red Unrecoverable fault may require device replacement .

Flashing Red/ Green Device is in sel f -test .

Indication Probable Cause

Network StatusOff Device is not online.

- Device has not completed dup_M AC_id test.

- Device not pow ered. Check module stat us indicator.

Flash ing Green Device i s onl ine but has no connect ions in the establ ished sta te .

Green Device is online and has connect ions in the establ ished state.

Fl ashi ng Re d One or m ore I/ O conne ct ions are i n t im ed-out st at e

Red Crit ical l ink failure is present w ith failed communicat ion device.

Device detected error that prevents it communicat ing on the

network.

Flashing

Red/Green

Communi cation faul ted device is present.

The device detected a net w ork access error and is in communicati on

faulted state.

Device received and accepted an Identif y Communicat ion Faulted

Request - l ong protocol m essage.


17/24



Indication Probable Cause1734-OE2C Probable Cause1734-OE2V

Channel Status

Off M odule is in CAL mode.

Green N ormal operat ion is present w ith channel act ively controll ing

outputs.

Flashing Green Channel is be ing cal ib ra ted.

Flashing Red Open w i re or no f ield pow er is

present.

A low or high clamp is present.

Red - No f ield pow er is present .


18/24



North American Hazardous Location Approval

The following information applies whenoperating this equipment in hazardouslocations:

Informations sur lutilisation de cet quipementen environnements dangereux:

Products marked CL I, DIV 2, GP A, B, C, D are suit ablefor use in Class I Division 2 Groups A , B, C, D, HazardousLocations and nonhazardous locations only. Each productis supplied w ith markings on the rating nameplateindicating the hazardous location temperature code. W hencombining products w ithin a system, t he most adversetemperature code (low est T number) may be used tohelp determine the overall temperature code of thesystem. Combinations of equipment in your system are

subject t o investigation by the local Aut hority HavingJurisdiction at the time of i nstallation.

Les produits marqus CL I, DIV 2, GP A, B, C, D neconviennent qu une uti lisatio n en environnements de Classe IDivision 2 Groupes A, B, C, D dangereux et non dangereux.Chaque produit est l ivr avec des marquages sur sa plaquedidentification qui indiquent le code de temprature pour lesenvironnement s dangereux. Lorsque plusieurs produits sontcombins dans un systme, le code de temprature le plusdfavorable (code de temprature le plus faible) peut treutil is pour dterminer le code de temprature global du

systme. Les combinaisons dquip ements dans le systmesont sujettes inspection par les autorits locales qualifiesau moment de l installation.

EXPLOSION HAZARD - Do not disconnect equipment unless

pow er has been removed or t he areais know n to be nonhazardous.

Do not disconnect connections tothis equipment unless power hasbeen removed or the area is knownto be nonhazardous. Secure anyexternal connections that mate tothis equipment by using screws,sliding latches, threadedconnectors, or other means providedw ith this product.

Substitut ion of components mayimpai r suitabili ty for Class I, Division2.

If t his product contains batteries,they must onl y be changed in anarea known to be nonhazardous.

RISQUE DEXPLOSION Couper le courant ou sassurer que

lenvironnement est class nondangereux avant de dbrancherl'quipement.

Couper le courant ou s'assurer quelenvironnement est class nondangereux avant de dbrancher lesconnecteurs. Fixer t ous lesconnecteurs externes relis cetquipement l'aide de vis, loquetscoulissants, connecteurs filets ouautres moyens fourni s avec ceproduit.

La substitution de composants peutrendre cet quipement inadapt uneutil isation en environnement deClasse 1, Division 2.

Sassurer que lenvironnement estclass non dangereux avant dechanger les piles.

WARNING AVERTISSEMENT


19/24



European Hazardous Location Approval

European Zone 2 Certification (The following applies when the product bears theEEx marking)This equipment is intended f or use in potentiall y explosive atmospheres as defined by

European Union Direct ive 94/ 9/ EC.

DEM KO certif ies that thi s equipment has been found to comply wi th the Essential Health

and Safety Requirement s relating to t he design and construction of Category 3 equipment

intended f or use in potenti ally explosive atmospheres, given in Annex II to thi s Directive.

The examinat ion and test results are recorded in confident ial report N o 03NK30347.

Compliance w ith t he Essential Health and Safet y Requirements has been assured bycompliance with EN 50021.

IMPORTANT O bserve the follow ing additional Zone 2 certification

requirem ents.

This equipm ent is not resistant to sunlight or

other sources of U V radiation.

The secondary of a current transform er shall not

be open-circuited w hen applied in Class I, Zone

2 environm ents.

Equipm ent of lesser Enclosure Type Rating m ust

be installed in an enclosure providing at least

IP54 protection w hen applied in Class I, Zone 2

environm ents. This equipm ent shall be used w ithin its specified

ratings defined by Allen-Bradley.

Provision shall be m ade to prevent the rated

voltage from being exceeded by transient

disturbances of m ore than 40% w hen applied in

Class I, Zone 2 environm ents.


20/24



Specifications

Output Specifications 1734-OE2C 1734-OE2V

Number of Outputs 2 single-ended, non-isolated

Resolut ion 13 bits - over 0-21mA

2.5A/ cnt (average value -

typical range:

2.3...2.7A/cnt)

14 bits

(13 plus sign)

1.28mV/cnt in unipolar or

bipolar mode

Output Current 0mA output unt i l

communication

established

4-20mA user configurable

0-20mA user configurable

-

Output Voltage - 0V output unt i l

communication

established

0-10V (user configurable)

(-0.0V under, +0.5V over)

+10V user configurable

(-0.5V under, +0.5V over)

Absolute A ccuracy1 Current Output

0.1% Full Scale @ 25oC

Voltage Output

0.1% Full Scale @ 25oC

Accuracy Drift w/Temp. 30ppm/ oC 5ppm/ oC

Step Response to 63% of FS 24 sCurrent Load on

Voltage Output

- 3mA

Resisti ve Load on

Current Output

0...750 -

Conversion Type Digital to analog converter

Conversion Rate 16s 20s

Data Format Signed Integer

Calibrat ion Factory Calibrated


21/24



General Specifications 1734-OE2C 1734-OE2V

M odule Locat ion 1734-TB, 1734-TBS, 1734-TB3, 17340TB3S

w iring base assembly

POINTBus Current 75 mA @5V dc

Pow er Dissipation -

M aximum at 28.8V

750 load on each output

- 1.23 W


- 1.83 W

1.0W

Thermal Dissipation -

M aximum at 28.8V

75 0load on each output

- 4.19 BTU/hr


- 6.24 BTU/ hr

3.4BTU/hr

Isolation Voltage

(Continuous-voltage

W ithstand Rating)

50V Continuous

Tested to w ithst and 2200V dc for 60 sNo isolation betw een individual channels

External dc pow er

Supply Voltage

Voltage Range

Supply Current

24V dc nominal

10...28.8V dc

70 mA @ 24V dc (including

outputs @20 mA)

24V dc nominal

10...28.8V dc

35 mA @ 24V dc (including

outputs @3 mA)

Indicators 1 green/ red module status indicator, logic side

1 green/ red netw ork stat us indicator, logic side

2 green/ red output stat us indicators, logic side

Keysw itch Posit ion 4

Dimensions H x W x L

56 x 12 x 75.5 mm (2.21 x 0.47 x 2.97 in)


22/24



General Specifications(Continued)

1734-OE2C 1734-OE2V

Operat ional Temperature IEC 60068-2-1 (Test Ad, Operat ing Cold),

IEC 60068-2-2 (Test Bd, Operating Dry Heat),

IEC 60068-2-14 (Test Nb , Operati ng Thermal Shock):

-20 55 C (-4 131 F)

Storage Temperature IEC 60068-2-1 (Test Ab, Unpackaged Nonoperat i ng Co ld ),

IEC 60068-2 -2 (Test Bb, Unpackaged N onopera ti ng Dry

Heat),

IEC 60068-2 -14 (Test N a, Unpackaged N onopera ti ng

Thermal Shock):

-40 85 C (-40 185 F)

Relat ive Humidity IEC 60068-2-30

(Test Db, Unpackaged Nonoperating Damp Heat):

5 95% noncondensing

Vibrat ion IEC60068-2-6 (Test Fc, Operat ing)

5 g @ 10...500 Hz

Shock

Operating

Non-Operating

IEC 60068-2-27 (Test Ea, Unpackaged Shock)

30 g

50 g

Emissions CISPR 11: Group 1, Class A

ESD Immunity IEC6100-4-2

6 kV contact di scharges

8 kV air discharges


23/24



General Specifications(Continued)

1734-OE2C 1734-OE2V

Radiated RF Immunity IEC 61000-4-3:

10 V/ m w ith 1kHz sine-wave 80% AM from 30 M Hz to

2000 M Hz

10 V/ m w ith 200 Hz 50% Pulse 100% AM at 900 M hz

10 V/ m w ith 200 Hz 50% Pulse 100% AM at 1890 M Hz

EFT/ B Immunit y IEC 61000-4-4:3 kV at 2.5 kHz on signal port s

Surge Transien t Immuni ty IEC 61000-4 -5:

2 kV line-earth(CM ) on shielded ports

Conduct ed RF Immunit y IEC61000-4-6

10 Vrms w ith 1 kHz sine-w ave 80% AM

from 150 kHz to 80 M Hz

Enclosure Type Rat ing N one (open-style)

W ire Size 14 AW G (2.5mm2) - 22 AW G (0.25mm 2) solid or stranded

copper w ire rated at 75 oC or greater

3/ 64 inch (1.2 mm) insulation m aximum

W ire Category2 1 - on signal ports

Terminal Base Screw Torque 0.6 Nm (7 lb-in)

W eight 0.036 kg (0.08 lb)

Publ ica ti ons - User M anua l 1734-UM 001


24/24

Publication1734-IN002C-EN-E - April 2005 PN 957955-48Supersedes Publication 1734-IN002B-EN-P - April 2002 and

Certification3 (When Product is Marked) 1734-OE2C 1734-OE2V

c-UL-us UL Listed Industrial Control Equipment ,

certif ied for U.S. and Canada

c-UL-us UL Listed for Class I, Divi sion 2 Group A,B,C,D

Hazardous Locati ons, certif ied for U.S. and Canada

CE European Union 89/ 336/EEC EM C Directive,

compliant w ith:

EN 50082-2; Industrial Immuni ty EN 61326; M eas./Control/ Lab., Industrial

Requirements

EN 61000-6-2; Industrial Immuni ty

EN 61000-6-4; Industrial Emissions

C-Tick Austral ian Radiocommuni cations Act ,

compliant w ith:

AS/ NZS CISPR 11, Industri al Emi ssions

EEX European Union 94/ 9/ EC ATEX Direct ive,

compliant w ith: EN 50021; Potent iall y Explosive At mospheres,

Protecti on n (Zone 2)

X

X

X

X

X

X

X

X

X

1. Includes off set, gain, non-linearit y and repeatabil ity error terms.2. Use this Category information for planning routing. Refer to Industrial Automation W iring and Grounding Guidelines, publicati on 1770-4.1.3. See the Product Certification l ink at w w w.ab.com f or Declarations of Conformity, Certificates, and other certification details.

PO IN T I/O , PO IN TBus, and RSLogix 5000 are tradem arks of Rockw ell Autom ation.ControlN et is a tradem ark of ControlN et International, Ltd.D eviceN et is a tradem ark of O pen D eviceN et Vendor Association.

Documents

Ult REL Output Analog Modules 1734-In002 En