SoundTraxx CurrentKeeper™ Tsunami® TSU-AT1000 Installation Notes Wiring Diagram Overview This application note describes how to install a CurrentKeeper onto a Tsunami TSU-AT1000 Digital Sound Decoder™. Bill of Materials P.N. Description TSU-AT1000 Digital Sound Decoder 810140 CurrentKeeper Tools You Will Need ■ 25W Soldering Iron ■ Rosin Core Solder ■ Wire Strippers ■ Wire Cutters Installation 1. Using wire cutters, remove the factory-installed capacitor from the Tsunami TSU-AT1000 Digital Sound Decoder by clipping the red and black wires, leaving about 3” of the black capacitor wire still attached to the decoder. The red capacitor wire may be removed and discarded. 2. Prepare the CurrentKeeper for installation: Using wire cutters, trim the blue and black wires to about 3” . 3. Strip and tin the ends of the wires on the CurrentKeeper, as well as the Tsunami’s black wire from the capacitor removed in Step 1. 4. Slide a piece of the black heat-shrink tubing (included) over the black Tsunami capacitor wire. Solder the black Tsunami wire to the black CurrentKeeper wire. Slide the piece of heat-shrink tubing over the connection and heat to insulate. 5. Solder the blue CurrentKeeper wire to tab 9 (Function Common). 6. Secure in place with Kapton® tape (or equivalent) if desired. Note: Once placed on the track, it will take about 2 minutes for the CurrentKeeper to be fully charged. TSU-AT1000 CurrentKeeper 1 2 3 4 10 9 8 7 5 6 141 Burnett Drive • Durango, CO 81301 Phone: (970) 259-0690 • Toll Free: 888-789-7637 • Fax: (970) 259-0691 Email: [email protected] • Website: www.soundtraxx.com ©2017 Throttle Up! Corp. All Rights Reserved

Tsunami® TSU-AT1000 Installation Notes - SoundTraxx · capacitor from the Tsunami TSU-AT1000 Digital Sound Decoder by clipping the red and black wires, leaving about 3” of the

Download PDF Report

Upload
others
View
8
Download
0

Embed Size (px)

Citation preview

Page 1: Tsunami® TSU-AT1000 Installation Notes - SoundTraxx · capacitor from the Tsunami TSU-AT1000 Digital Sound Decoder by clipping the red and black wires, leaving about 3” of the

SoundTraxx CurrentKeeper™Tsunami® TSU-AT1000 Installation Notes

Wiring DiagramOverviewThis application note describes how to install a CurrentKeeper onto a Tsunami TSU-AT1000 Digital Sound Decoder™.

Bill of MaterialsP.N. Description TSU-AT1000 Digital Sound Decoder810140 CurrentKeeper

Tools You Will Need■ 25W Soldering Iron■ Rosin Core Solder■ Wire Strippers■ Wire Cutters

Installation1. Using wire cutters, remove the factory-installed

capacitor from the Tsunami TSU-AT1000 Digital Sound Decoder by clipping the red and black wires, leaving about 3” of the black capacitor wire still attached to the decoder. The red capacitor wire may be removed and discarded.

2. Prepare the CurrentKeeper for installation: Using wire cutters, trim the blue and black wires to about 3”.

3. Strip and tin the ends of the wires on the CurrentKeeper, as well as the Tsunami’s black wire from the capacitor removed in Step 1.

4. Slide a piece of the black heat-shrink tubing (included) over the black Tsunami capacitor wire. Solder the black Tsunami wire to the black CurrentKeeper wire. Slide the piece of heat-shrink tubing over the connection and heat to insulate.

5. Solder the blue CurrentKeeper wire to tab 9 (Function Common).

6. Secure in place with Kapton® tape (or equivalent) if desired.

Note: Once placed on the track, it will take about 2 minutes for the CurrentKeeper to be fully charged.

TSU-750

TSU-AT1000

TSU-BW1000Side A

Side B

TSU-GN1000

TSU-IM1000

TSU-KT1000Side A

Side B

TSU-1000