TS3A27518E 6-Channel, 1:2 Multiplexer/Demultiplexer with ... · TS3A27518E 6-Channel, 1:2 Multiplexer/Demultiplexer with ... ... b

VCC

IN2

GND

NC1

NO1

COM1

NC2

NO2

COM2

NC3

NO3

COM3

NC4

NO4

COM4

NC5

NO5

COM5

NC6

NO6

COM6

IN1

ENLogic

Copyright © 2016, Texas Instruments Incorporated

Product

Folder

Sample &Buy

Technical

Documents

Tools &

Software

Support &Community

An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,intellectual property matters and other important disclaimers. PRODUCTION DATA.

TS3A27518ESCDS260D –MARCH 2009–REVISED MAY 2016

TS3A27518E 6-Channel, 1:2 Multiplexer/Demultiplexer with Integrated IEC L-4 ESD and1.8-V Logic Compatible Control Inputs

1

1 Features1• 1.65-V to 3.6-V Single-Supply Operation• Isolation in Power-Down Mode, VCC = 0• Low-Capacitance Switches, 21.5 pF (Typical)• Bandwidth Up to 240 MHz for High-Speed

Rail-to-Rail Signal Handling• Crosstalk and OFF Isolation of –62 dB• 1.8-V Logic Threshold Compatibility for Control

Inputs• 3.6-V Tolerant Control Inputs• Latch-Up Performance Exceeds 100-mA Per

JESD 78, Class II• ESD Performance Tested Per JESD 22

– 2500-V Human-Body Model (A114-B, Class II)– 1500-V Charged-Device Model (C101)

• ESD Performance: NC/NO Ports– ±6-kV Contact Discharge (IEC 61000-4-2)

• 24-WQFN (4.00 mm × 4.00 mm), 24-BGA(3.00 mm × 3.00 mm) and 24-TSSOP(7.90 mm × 6.60 mm) Packages

2 Applications• SD-SDIO and MMC Two-Port MUX• PC VGA Video MUX-Video Systems• Audio and Video Signal Routing

3 DescriptionThe TS3A27518E is a bidirectional, 6-channel,1:2 multiplexer-demultiplexer designed to operatefrom 1.65 V to3.6 V. This device can handle both digital and analogsignals, and can transmit signals up to VCC in eitherdirection. The TS3A27518E has two control pins,each controlling three 1:2 muxes at the same time,and an enable pin that put all outputs in high-impedance mode. The control pins are compatiblewith 1.8-V logic thresholds and are backwardcompatible with 2.5-V and 3.3-V logic thresholds.

The TS3A27518E allows any SD, SDIO, andmultimedia card host controllers to expand out tomultiple cards or peripherals because the SDIOinterface consists of 6-bits: CMD, CLK, and Data[0:3]signals. The TS3A27518E has two control pins thatgive additional flexibility to the user. For example, theability to mux two different audio-video signals inequipment such as an LCD television, an LCDmonitor, or a notebook docking station.

Device Information(1)

PART NUMBER PACKAGE BODY SIZE (NOM)

TS3A27518E

WQFN (24) 4.00 mm × 4.00 mmTSSOP (24) 7.90 mm × 6.60 mmBGA MICROSTARJUNIOR (24) 3.00 mm × 3.00 mm

(1) For all available packages, see the orderable addendum atthe end of the data sheet.

Functional Block Diagram

http://www.ti.com/product/ts3a27518e?qgpn=ts3a27518e

http://www.ti.com/product/TS3A27518E?dcmp=dsproject&hqs=pf

http://www.ti.com/product/TS3A27518E?dcmp=dsproject&hqs=sandbuy&#samplebuy

http://www.ti.com/product/TS3A27518E?dcmp=dsproject&hqs=td&#doctype2

http://www.ti.com/product/TS3A27518E?dcmp=dsproject&hqs=sw&#desKit

http://www.ti.com/product/TS3A27518E?dcmp=dsproject&hqs=support&#community

2

TS3A27518ESCDS260D –MARCH 2009–REVISED MAY 2016 www.ti.com

Product Folder Links: TS3A27518E

Submit Documentation Feedback Copyright © 2009–2016, Texas Instruments Incorporated

Table of Contents1 Features .................................................................. 12 Applications ........................................................... 13 Description ............................................................. 14 Revision History..................................................... 25 Pin Configuration and Functions ......................... 36 Specifications......................................................... 5

6.1 Absolute Maximum Ratings ...................................... 56.2 ESD Ratings.............................................................. 56.3 Recommended Operating Conditions....................... 56.4 Thermal Information .................................................. 56.5 Electrical Characteristics for 3.3-V Supply ............... 66.6 Electrical Characteristics for 2.5-V Supply ............... 86.7 Electrical Characteristics for 1.8-V Supply ............... 96.8 Typical Characteristics ............................................ 12

7 Parameter Measurement Information ................ 158 Detailed Description ............................................ 20

8.1 Overview ................................................................. 20

8.2 Functional Block Diagram ....................................... 208.3 Feature Description................................................. 208.4 Device Functional Modes........................................ 20

9 Application and Implementation ........................ 219.1 Application Information............................................ 219.2 Typical Application .................................................. 21

10 Power Supply Recommendations ..................... 2311 Layout................................................................... 23

11.1 Layout Guidelines ................................................. 2311.2 Layout Example ................................................... 23

12 Device and Documentation Support ................. 2412.1 Community Resources.......................................... 2412.2 Trademarks ........................................................... 2412.3 Electrostatic Discharge Caution............................ 2412.4 Glossary ................................................................ 24

13 Mechanical, Packaging, and OrderableInformation ........................................................... 24

4 Revision HistoryNOTE: Page numbers for previous revisions may differ from page numbers in the current version.

Changes from Revision C (December 2015) to Revision D Page

• Updated Pin Functions table .................................................................................................................................................. 1

Changes from Revision B (May 2009) to Revision C Page

• Added ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementationsection, Power Supply Recommendations section, Layout section, Device and Documentation Support section, andMechanical, Packaging, and Orderable Information section .................................................................................................. 1


http://www.ti.com


http://www.go-dsp.com/forms/techdoc/doc_feedback.htm?litnum=SCDS260D&partnum=TS3A27518E

1 2 3 4 5

A

B

C

D

E

1 24

2 23

3 22

4 21

5 20

6 19

7 18

8 17

9 16

10 15

11 14

12 13

IN1

NC3

NC6

NC4

EN

NC5

NO5

NO4

NO6

NO3

IN2

NO2

NC2

NC1

N.C.

COM1

GND

COM2

COM3

VCC

COM4

COM5

NO1

COM6

CO

M5

IN2

NO

1

CO

M6

NO

3

NO

2

N.C

.

NC

6

NC

1

NC

3

NC

2

IN1

COM3

COM2

COM1

VCC

GND

COM4

NO5

NO4

NO6

NC4

NC5

EN

1

2

3

4

5

6

7

24

8

23

15

14

13

12

19

11

20

10

21

9

22

16

17

18

3

TS3A27518Ewww.ti.com SCDS260D –MARCH 2009–REVISED MAY 2016


Submit Documentation FeedbackCopyright © 2009–2016, Texas Instruments Incorporated

5 Pin Configuration and Functions

RTW Package24-Pin WQFN

Top ViewPW Package

24-Pin TSSOPTop View

ZQS Package24-Pin BGA MICROSTAR JUNIOR

Top View

Pin FunctionsPIN

I/O DESCRIPTIONNAME RTW ZQS PW

COM1 1 A1 4 I/O Common-signal pathCOM2 3 B1 6 I/O Common-signal pathCOM3 4 C1 7 I/O Common-signal pathCOM4 6 D1 9 I/O Common-signal pathCOM5 7 E1 10 I/O Common-signal pathCOM6 9 D2 12 I/O Common-signal pathEN 17 C4 20 I Digital control to enable or disable all signal pathsGND 2 C3 5 — Ground.IN1 21 B4 24 I Digital control to connect COM to NC or NOIN2 11 D3 14 I Digital control to connect COM to NC or NON.C. 24 A3 3 — Not connectedNC1 23 B3 2 I/O Normally closed-signal pathNC2 22 A2 1 I/O Normally closed-signal pathNC3 20 A4 23 I/O Normally closed-signal pathNC4 18 B5 21 I/O Normally closed-signal pathNC5 16 C5 19 I/O Normally closed-signal pathNC6 19 A5 22 I/O Normally closed-signal pathNO1 8 E2 11 I/O Normally open-signal pathNO2 10 E3 13 I/O Normally open-signal path


http://www.ti.com



4




Pin Functions (continued)PIN

I/O DESCRIPTIONNAME RTW ZQS PW

NO3 12 E4 15 I/O Normally open-signal pathNO4 14 D5 17 I/O Normally open-signal pathNO5 15 D4 18 I/O Normally open-signal pathNO6 13 E5 16 I/O Normally open-signal pathVCC 5 C2 8 — Voltage supply


http://www.ti.com



5




(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratingsonly, which do not imply functional operation of the device at these or any other conditions beyond those indicated under RecommendedOperating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

(2) The algebraic convention, whereby the most negative value is a minimum and the most positive value is a maximum.(3) All voltages are with respect to ground, unless otherwise specified.(4) The input and output voltage ratings may be exceeded if the input and output clamp-current ratings are observed.(5) This value is limited to 5.5-V maximum.(6) Requires clamp diodes on analog port to VCC.(7) Pulse at 1-ms duration < 10% duty cycle.

6 Specifications

6.1 Absolute Maximum Ratingsover operating free-air temperature range (unless otherwise noted) (1) (2)

MIN MAX UNITVCC Supply voltage (3) –0.5 4.6 VVNCVNOVCOM

Analog signal voltage (3) (4) (5) –0.5 4.6 V

IK Analog port diode current (6) VCC < VNC, VNO, VCOM < 0 –50 mAINCINOICOM

ON-state switch current (7) VNC, VNO, VCOM = 0 to VCC –50 50 mA

VI Digital input voltage (3) (4) –0.5 4.6 VIIK Digital input clamp current (3) (4) VIO < VI < 0 –50 mAICC Continuous current through VCC 100 mAIGND Continuous current through GND –100 mATstg Storage temperature –65 150 °C

(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.

6.2 ESD RatingsVALUE UNIT

V(ESD) Electrostatic dischargeHuman-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) ±2500

VCharged-device model (CDM), per JEDEC specification JESD22-C101 (2) ±1500

6.3 Recommended Operating Conditionsover operating free-air temperature range (unless otherwise noted)

MIN MAX UNITSupply voltage VCC 1.65 3.6 V

Analog signal voltageVNC

0 VCC VVNO

VCOM

Digital input voltage VI 0 VCC V

(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics applicationreport, SPRA953.

6.4 Thermal Information

THERMAL METRIC (1)

TS3A27518E

UNITPW(TSSOP)

RTW(WQFN)

ZQS (BGAMICROSTAR JUNIOR)

24 PINS 24 PINS 24 PINSRθJA Junction-to-ambient thermal resistance 104 40.7 155.7 °C/WRθJC(top) Junction-to-case (top) thermal resistance 51.6 42.9 69.9 °C/WRθJB Junction-to-board thermal resistance 57.5 19.2 94.6 °C/W


http://www.ti.com



http://www.ti.com/lit/pdf/spra953

6




Thermal Information (continued)

THERMAL METRIC (1)

TS3A27518E

UNITPW(TSSOP)

RTW(WQFN)

ZQS (BGAMICROSTAR JUNIOR)

24 PINS 24 PINS 24 PINSψJT Junction-to-top characterization parameter 9.9 1 9 °C/WψJB Junction-to-board characterization parameter 57.1 19.3 92.2 °C/WRθJC(bot) Junction-to-case (bottom) thermal resistance — 8 — °C/W

(1) The algebraic convention, whereby the most negative value is a minimum and the most positive value is a maximum.

6.5 Electrical Characteristics for 3.3-V Supply (1)

VCC = 3 V to 3.6 V, TA = –40°C to +85°C (unless otherwise noted)PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

ANALOG SWITCH

VCOM,VNO, VNC

Analog signal voltage 0 VCC V

ron ON-state resistance VCC = 3 V0 ≤ (VNC or VNO)≤ VCC,ICOM = –32 mA

Switch ON,see Figure 15

TA = 25°C 4.4 6.2VTA = –40°C to

+85°C 7.6

Δron

ON-stateresistance matchbetween channels

VCC = 3 VVNC or VNO = 2.1V,ICOM = –32 mA


TA = 25°C 0.3 0.7ΩTA = –40°C to

+85°C 0.8

ron(flat)

ON-stateresistanceflatness

VCC = 3 V0 ≤ (VNC or VNO)≤ VCC,ICOM = –32 mA


TA = 25°C 0.95 2.1ΩTA = –40°C to

+85°C 2.3

INC(OFF),INO(OFF)

NC, NOOFF leakagecurrent

VCC = 3.6 V

VNC or VNO = 1V,VCOM = 3 V,orVNC or VNO = 3V,VCOM = 1 V

Switch OFF,see Figure 16

TA = 25°C –0.5 0.05 0.5

μA

TA = –40°C to+85°C –7 7

INC(PWROFF),INO(PWROFF)

VCC = 0 V

VNC or VNO = 0to 3.6 V,VCOM = 3.6 V to0,orVNC or VNO = 3.6V to 0,VCOM = 0 to 3.6V

TA = 25°C –1 0.05 1

TA = –40°C to+85°C –12 12

ICOM(OFF)

COMOFF leakagecurrent

VCC = 3.6 V

VNC or VNO = 3V,VCOM = 1 V,orVNC or VNO = 1V,VCOM = 3 V


TA = 25°C –1 0.01 1

μA

TA = –40°C to+85°C –2 2

ICOM(PWROFF) VCC = 0 V

VNC or VNO = 3.6V to 0,VCOM = 0 to 3.6V,orVNC or VNO = 0to 3.6 V,VCOM = 3.6 V to0

TA = 25°C –1 0.02 1

TA = –40°C to+85°C –12 1

INO(ON),INC(ON)

NC, NOON leakagecurrent

VCC = 3.6 V

VNC or VNO = 1V,VCOM = open,orVNC or VNO = 3V,VCOM = open


TA = 25°C –2.5 0.04 2.2

μATA = –40°C to+85°C –7 7


http://www.ti.com



7




Electrical Characteristics for 3.3-V Supply(1) (continued)VCC = 3 V to 3.6 V, TA = –40°C to +85°C (unless otherwise noted)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

(2) All unused digital inputs of the device must be held at VCC or GND to ensure proper device operation. See the TI application report,Implications of Slow or Floating CMOS Inputs, SCBA004.

ICOM(ON)

COMON leakagecurrent

VCC = 3.6 V

VNC or VNO =open,VCOM = 1 V,orVNC or VNO =open,VCOM = 3 V


TA = 25°C –2 0.03 2

μATA = –40°C to+85°C –7 7

DIGITAL CONTROL INPUTS (IN1, IN2, EN) (2)

VIH Input logic high VCC = 3.6 V TA = –40°C to+85°C 1.2 3.6 V

VIL Input logic low VCC = 3.6 V TA = –40°C to+85°C 0 0.65 V

IIH, IIL Input leakage current VCC = 3.6 V VI = VCC or 0TA = 25°C –0.1 0.05 0.1

μATA = –40°C to+85°C –2.5 2.5

DYNAMIC

tON Turnon timeVCC = 3.3 V

VCOM = VCC,RL = 50 Ω

CL = 35 pF,see Figure 19

TA = 25°C 18.1 59nsVCC = 3 V to

3.6 VTA = –40°C to+85°C 60

tOFF Turnoff timeVCC = 3.3 V



TA = 25°C 25.4 60.6nsVCC = 3 V to

3.6 VTA = –40°C to+85°C 61

tBBMBreak-before-make time

VCC = 3.3 V VNC = VNO =VCC/2,RL = 50 Ω


TA = 25°C 4 11.1 22.7nsVCC = 3 V to

3.6 VTA = –40°C to+85°C 28

QC Charge injection VCC = 3.3 V VGEN = 0,RGEN = 0

CL = 0.1 nF,see Figure 24 TA = 25°C 0.81 pC

CNC(OFF),CNO(OFF)

NC, NOOFF capacitance VCC = 3.3 V

VNC or VNO =VCC or GND,Switch OFF

See Figure 18 TA = 25°C 13 pF

CCOM(OFF)COMOFF capacitance VCC = 3.3 V


See Figure 18 TA = –40°C to+85°C 8.5 pF

CNC(ON),CNO(ON)

NC, NOON capacitance VCC = 3.3 V


See Figure 18 21.5 pF

CCOM(ON)COMON capacitance VCC = 3.3 V

VCOM = VCC orGND,Switch ON


CIDigital inputcapacitance VCC = 3.3 V VI = VCC or GND See Figure 18 2 pF

BW Bandwidth VCC = 3.3 V RL = 50 Ω, Switch ON,see Figure 20 240 MHz

OISO OFF isolation VCC = 3.3 V RL = 50 Ω,f = 10 MHz

Switch OFF,see Figure 22 –62 dB

XTALK Crosstalk VCC = 3.3 V RL = 50 Ω,f = 10 MHz

Switch ON,see Figure 23 –62 dB

XTALK(ADJ) Crosstalk adjacent VCC = 3.3 V RL = 50 Ω,f = 10 MHz


THD Total harmonicdistortion VCC = 3.3 V RL = 600 Ω,

CL = 50 pFf = 20 Hz to 20 kHz,see Figure 25 0.05%

SUPPLY

ICCPositivesupply current VCC = 3.6 V VI = VCC or GND Switch ON or OFF

TA = 25°C 0.04 0.3μATA = –40°C to

+85°C 3


http://www.ti.com



http://www.ti.com/lit/pdf/SCBA004

8




(1) The algebraic convention, whereby the most negative value is a minimum and the most positive value is a maximum.(2) All unused digital inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,

Implications of Slow or Floating CMOS Inputs, SCBA004.


VCC = 2.3 V to 2.7 V, TA = –40°C to +85°C (unless otherwise noted)PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

ANALOG SWITCH

VCOM,VNO, VNC

Analog signalvoltage 0 VCC V

ronON-stateresistance VCC = 2.3 V 0 ≤ (VNC or VNO) ≤ VCC,

ICOM = –32 mASwitch ON,see Figure 15

TA = 25°C 5.5 9.6ΩTA = –40°C to

+85°C 11.5

Δron

ON-stateresistancematchbetweenchannels

VCC = 2.3 V VNC or VNO = 1.6 V,ICOM = –32 mA


TA = 25°C 0.3 0.8

ΩTA = –40°C to+85°C 0.9

ron(flat)


VCC = 2.3 V 0 ≤ (VNC or VNO) ≤ VCC,ICOM = –32 mA


TA = 25°C 0.91 2.2ΩTA = –40°C to

+85°C 2.3

INC(OFF),INO(OFF)

NC, NOOFF leakagecurrent

VCC = 2.7 V

VNC or VNO = 0.5 V,VCOM = 2.3 V,orVNC or VNO = 2.3 V,VCOM = 0.5 V Switch OFF,

see Figure 16

TA = 25°C –0.3 0.04 0.3

μA

TA = –40°C to+85°C –6 6


VCC = 0 V

VNC or VNO = 0 to 2.7 V,VCOM =2.7 V to 0,orVNC or VNO = 2.7 V to 0,VCOM = 0 to 2.7 V

TA = 25°C –0.6 0.02 0.6

TA = –40°C to+85°C –10 10

ICOM(OFF)

COMOFF leakagecurrent

VCC = 2.7 V

VNC or VNO = 0.5 V,VCOM = 2.3 V,orVNC or VNO = 2.3 V,VCOM = 0.5 V Switch OFF,

see Figure 16

TA = 25°C –0.7 0.02 0.7

μA

TA = –40°C to+85°C –1 1


VNC or VNO = 2.7 V to 0,VCOM = 0 to 2.7 V,orVNC or VNO = 0 to 2.7 V,VCOM = 2.7 V to 0

TA = 25°C –0.7 0.02 0.7

TA = –40°C to+85°C –7.2 7.2

INO(ON)INC(ON)

NC, NOON leakagecurrent

VCC = 2.7 VVNC or VNO = 0.5 V or2.3 V,VCOM = open


TA = 25°C –2.1 0.03 2.1μATA = –40°C to

+85°C –6 6

ICOM(ON)

COMON leakagecurrent

VCC = 2.7 V

VNC or VNO = open,VCOM = 0.5 V,orVNC or VNO = open,VCOM = 2.3 V


TA = 25°C –2 0.02 2

μATA = –40°C to+85°C –5.7 5.7


VIH Input logic high VCC = 2.7 V VI = VCC or GND TA = –40°C to+85°C 1.15 3.6 V

VIL Input logic low VCC = 2.7 V 0 0.55 V

IIH, IILInput leakagecurrent VCC = 2.7 V VI = VCC or 0

TA = 25°C –0.1 0.01 0.1μATA = –40°C to

+85°C –2.1 2.1

DYNAMIC

tON Turnon timeVCC = 2.5 V



TA = 25°C 17.2 36.8nsVCC = 2.3 V to

2.7 VTA = –40°C to+85°C 42.5

tOFF Turnoff timeVCC = 2.5 V



TA = 25°C 17.1 29.8nsVCC = 2.3 V to

2.7 VTA = –40°C to+85°C 34.4

tBBMBreak-before-make time

VCC = 2.5 VVNC = VNO = VCC/2,RL = 50 Ω


TA = 25°C 4.5 13 30nsVCC = 2.3 V to

2.7 VTA = –40°C to+85°C 33.3


http://www.ti.com




9




Electrical Characteristics for 2.5-V Supply(1) (continued)VCC = 2.3 V to 2.7 V, TA = –40°C to +85°C (unless otherwise noted)


QCChargeinjection VCC = 2.5 V VGEN = 0,

RGEN = 0CL = 0.1 nF,see Figure 24 0.47 pC

CNC(OFF),CNO(OFF)

NC, NOOFFcapacitance

VCC = 2.5 VVNC or VNO = VCC orGND,switch OFF


CCOM(OFF)

COMOFFcapacitance


See Figure 18 TA = –40°C to+85°C 9 pF

CNC(ON),CNO(ON)

NC, NOON capacitance VCC = 2.5 V

VNC or VNO = VCC orGND,switch OFF

See Figure 18 22 pF

CCOM(ON)COMON capacitance VCC = 2.5 V VCOM = VCC or GND,

switch ON See Figure 18 22 pF

CIDigital inputcapacitance VCC = 2.5 V VI = VCC or GND See Figure 18 2 pF

BW Bandwidth VCC = 2.5 V RL = 50 Ω Switch ON,see Figure 20 240 MHz

OISO OFF isolation VCC = 2.5 V RL = 50 Ω,f = 10 MHz

Switch OFF,see Figure 22 –62 dB



XTALK(ADJ)Crosstalkadjacent VCC = 2.5 V RL = 50 Ω,

f = 10 MHzSwitch ON,see Figure 23 –71 dB

THD Total harmonicdistortion VCC = 2.5 V RL = 600 Ω,

CL = 50 pFf = 20 Hz to 20 kHz,see Figure 25 0.06%

SUPPLY

ICCPositivesupply current VCC = 2.7 V VI = VCC or GND Switch ON or OFF

TA = 25°C 0.01 0.1μATA = –40°C to

+85°C 2

(1) The algebraic convention, whereby the most negative value is a minimum and the most positive value is a maximum.


VCC = 1.65 V to 1.95 V, TA = –40°C to 85°C (unless otherwise noted)PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

ANALOG SWITCH

VCOM,VNO, VNC

Analogsignalvoltage

0 VCC V

ronON-stateresistance VCC = 1.65 V

0 ≤ (VNC or VNO) ≤VCC,ICOM = –32 mA


TA = 25°C 7.1 14.4Ω

TA = –40°C to +85°C 16.3

Δron

ON-stateresistancematchbetweenchannels

VCC = 1.65 V VNC or VNO = 1.5 V,ICOM = –32 mA


TA = 25°C 0.3 1

ΩTA = –40°C to +85°C 1.2

ron(flat)


VCC = 1.65 V0 ≤ (VNC or VNO) ≤VCC,ICOM = –32 mA


TA = 25°C 2.7 5.5Ω

TA = –40°C to +85°C 7.3

INC(OFF),INO(OFF)

NC, NOOFFleakagecurrent

VCC = 1.95 V

VNC or VNO = 0.3 V,VCOM = 1.65 V,orVNC or VNO = 1.65 V,VCOM = 0.3 V


TA = 25°C –0.25 0.03 0.25

μATA = –40°C to +85°C –5 5


VCC = 0 V

VNC or VNO = 1.95 Vto 0,VCOM = 0 to 1.95 V,orVNC or VNO = 0 to1.95 V,VCOM = 1.95 V to 0

TA = 25°C –0.4 0.01 0.4

μATA = –40°C to +85°C –7.2 7.2


http://www.ti.com



10




Electrical Characteristics for 1.8-V Supply(1) (continued)VCC = 1.65 V to 1.95 V, TA = –40°C to 85°C (unless otherwise noted)


(2) All unused digital inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,Implications of Slow or Floating CMOS Inputs, SCBA004.

ICOM(OFF)

COMOFFleakagecurrent

VCC = 1.95 V

VNC or VNO = 0.3 V,VCOM = 1.65 V,orVNC or VNO = 1.65 V,VCOM = 0.3 V


TA = 25°C –0.4 0.02 0.4

μATA = –40°C to +85°C –0.9 0.9


VNC or VNO = 1.95 Vto 0,VCOM = 0 to 1.95 V,orVNC or VNO = 0 to1.95 V,VCOM = 1.95 V to 0

TA = 25°C –0.4 0.02 0.4

μATA = –40°C to +85°C –5 5

INO(ON),INC(ON)

NC, NOONleakagecurrent

VCC = 1.95 V

VNC or VNO = 0.3 V,VCOM = open,orVNC or VNO = 1.65 V,VCOM = open


TA = 25°C –2 0.02 2

μATA = –40°C to +85°C –5.2 5.2

ICOM(ON)

COMONleakagecurrent

VCC = 1.95 V

VNC or VNO = open,VCOM = 0.3 V,orVNC or VNO = open,VCOM = 1.65 V


TA = 25°C –2 0.02 2

μATA = –40°C to +85°C –5.2 5.2


VIHInput logichigh VCC = 1.95 V VI = VCC or GND TA = –40°C to +85°C 1 3.6 V

VILInput logiclow VCC = 1.95 V TA = –40°C to +85°C 0 0.4 V

IIH, IILInputleakagecurrent

VCC = 1.95 V VI = VCC or 0TA = 25°C –0.1 0.01 0.1

μATA = –40°C to +85°C –2.1 2.1

DYNAMIC

tONTurnontime

VCC = 1.8 VVCOM = VCC,RL = 50 Ω


TA = 25°C 14.1 49.3nsVCC = 1.65 V

to 1.95 V TA = –40°C to +85°C 56.7

tOFFTurnofftime

VCC = 1.8 VVCOM = VCC,RL = 50 Ω


TA = 25°C 16.1 26.5nsVCC = 1.65 V

to 1.95 V TA = –40°C to +85°C 31.2

tBBM

Break-before-make time

VCC = 1.8 VVNC = VNO = VCC/2,RL = 50 Ω


TA = 25°C 5.3 18.4 58nsVCC = 1.65 V

to 1.95 V TA = –40°C to +85°C 58

QCChargeinjection VCC = 1.8 V VGEN = 0,

RGEN = 0CL = 1 nF,see Figure 24 0.21 pC

CNC(OFF),CNO(OFF)

NC, NOOFFcapacitance


See Figure 18 9 pF

CNC(ON),CNO(ON)

NC, NOONcapacitance


See Figure 18 22 pF

CCOM(ON)

COMONcapacitance

VCC = 1.8 V VCOM = VCC or GND,switch ON See Figure 18 22 pF

CI

Digitalinputcapacitance

VCC = 1.8 V VI = VCC or GND See Figure 18 2 pF

BW Bandwidth VCC = 1.8 V RL = 50 Ω Switch ON,see Figure 20 240 MHz

OISOOFFisolation VCC = 1.8 V RL = 50 Ω,

f = 10 MHzSwitch OFF,see Figure 22 –60 dB


http://www.ti.com




11




Electrical Characteristics for 1.8-V Supply(1) (continued)VCC = 1.65 V to 1.95 V, TA = –40°C to 85°C (unless otherwise noted)




XTALK(ADJ)Crosstalkadjacent VCC = 1.8 V RL = 50 Ω,

f = 10 MHzSwitch ON,see Figure 23 –71 dB

THDTotalharmonicdistortion

VCC = 1.8 V RL = 600 Ω,CL = 50 pF

f = 20 Hz to 20 kHz,see Figure 25 0.1%

SUPPLY

ICC

Positivesupplycurrent

VCC = 1.95 V VI = VCC or GND Switch ON or OFFTA = 25°C 0.01 0.1

μATA = –40°C to +85°C 1.5


http://www.ti.com



0.0 2.0

Input Voltage, VIN (V)

Ou

tpu

tV

olta

ge,

V(V

)O

UT

0.0

4.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

0.2 0.4 0.6 0.8 1.0 1.2 1.61.4 1.80.0 4.0

Supply Voltage, V+ (V)

Su

pp

ly C

urr

en

t,I

(nA

)+

–5

45

0

5

10

15

20

25

30

35

40

0.5 1.0 1.5 2.0 2.5 3.0 3.5

INx = High

INx = Low

0.0 1.8

COM Voltage, V (V)COM

ON

-Sta

te R

esis

tan

ce,

r(

)O

NW

0

12

2

4

6

8

10

0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6

85ºC

25ºC

-–40ºC

Temperature, TA (°C)

Le

aka

ge

Cu

rre

nt,

I(n

A)

I

0

600

50

100

150

200

250

300

350

400

450

500

550

–40 25 85

COM (OFF)

COM (ON)

NO (OFF)

NO (ON)

0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5


0

1

2

3

4

5

6

7

ON

-Sta

te R

esis

tan

ce,

r(

)O

NW

85ºC

25ºC

–40ºC

0.0 0.5 1.0 1.5 2.0 2.5


0

8

ON

-Sta

te R

esis

tan

ce,

r(

)O

NW

1

2

3

4

5

6

7

85ºC

25ºC

-–40ºC

12




6.8 Typical Characteristics

Figure 1. ON-State Resistance vs COM Voltage (VCC = 3 V) Figure 2. ON-State Resistance vs COM Voltage (VCC = 2.3 V)

Figure 3. ON-State Resistance vs COM Voltage(VCC = 1.65 V)

Figure 4. Leakage Current vs Temperature (VCC = 3.3 V)

Figure 5. Supply Current vs Supply Voltage Figure 6. Control Input Thresholds (IN1, TA = 25°C)


http://www.ti.com



Bias Voltage (V)

Charg

e Inje

ction, Q

(pC

)C

–7

1

–6

–5

–4

–3

–2

–1

0

0 0.3 0.6 0.9 1.2 1.5 1.8

Ma

gn

itu

de

(d

B)

–20

0

–18

–16

–14

–12

–10

–8

–6

–4

–2

1.8 V

2.5 V

3.3 V

Frequency ( z)MH

0.1 1 10 100 1000

Magnitude (

dB

)

–100

–10

–90

–80

–70

–60

–50

–40

–30

–20

1.8 V

2.5 V

3.3 V

Frequency ( z)MH0.1 1 10 100 10000.1 1000

Frequency (Hz)

Tota

l H

arm

onic

Dis

tort

ion,T

HD

(%

)

0.05

0.11

0.06

0.07

0.08

0.09

0.10

1 10 100

1.8 V

2.5 V

3.3 V

Ma

gn

itu

de

(d

B)

–100

–10

–80

–90

–70

–60

–50

–40

–30

–20

1.8 V

2.5 V

3.3 V

Frequency ( z)MH0.1 1 10 100 1000

Frequency ( z)MH

Magnitude (

dB

)

–100

–10

–80

–90

–70

–60

–50

–40

–30

–20

0.1 1 10 100 1000

NO1TOCOM1-NO2

NO1TOCOM1-NO3

NO1TOCOM1-NO4

NO1TOCOM1-NO5

NO1TOCOM1-NO6

13




Typical Characteristics (continued)

Figure 7. Crosstalk Adjacent Figure 8. Crosstalk

Figure 9. Total Harmonic Distortion vs Frequency Figure 10. OFF Isolation

Figure 11. Insertion Loss Figure 12. Charge Injection vs Bias Voltage (1.8 V)


http://www.ti.com



Bias Voltage (V)

Charg

e Inje

ction, Q

(pC

)C

–16

–14

–12

–10

4

–8

–6

–4

–2

0

0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.4 2.7 3.0 3.3

2

Bias Voltage (V)

Charg

e Inje

ction, Q

(pC

)C

–10

2

–8

–6

–4

–2

0

0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.5

14




Typical Characteristics (continued)

Figure 13. Charge Injection vs Bias Voltage (2.5 V) Figure 14. Charge Injection vs Bias Voltage (3.3 V)


http://www.ti.com



15




7 Parameter Measurement Information

Table 1. Parameter DescriptionDESCRIPTION

VCOM Voltage at COM.VNC Voltage at NC.VNO Voltage at NO.ron Resistance between COM and NC or NO ports when the channel is ON.Δron Difference of ron between channels in a specific device.ron(flat) Difference between the maximum and minimum value of ron in a channel over the specified range of conditions.INC(OFF) Leakage current measured at the NC port, with the corresponding channel (NC to COM) in the OFF state.

INC(ON)Leakage current measured at the NC port, with the corresponding channel (NC to COM) in the ON state and the output(COM) open.

INO(OFF) Leakage current measured at the NO port, with the corresponding channel (NO to COM) in the OFF state.

INO(ON)Leakage current measured at the NO port, with the corresponding channel (NO to COM) in the ON state and the output(COM) open.

ICOM(OFF) Leakage current measured at the COM port, with the corresponding channel (COM to NC or NO) in the OFF state.

ICOM(ON)Leakage current measured at the COM port, with the corresponding channel (COM to NC or NO) in the ON state and theoutput (NC or NO) open.

VIH Minimum input voltage for logic high for the control input (IN, EN).VIL Maximum input voltage for logic low for the control input (IN, EN).VI Voltage at the control input (IN, EN).IIH, IIL Leakage current measured at the control input (IN, EN).

tONTurnon time for the switch. This parameter is measured under the specified range of conditions and by the propagationdelay between the digital control (IN) signal and analog output (NC or NO) signal when the switch is turning ON.

tOFFTurnoff time for the switch. This parameter is measured under the specified range of conditions and by the propagationdelay between the digital control (IN) signal and analog output (NC or NO) signal when the switch is turning OFF.

QC

Charge injection is a measurement of unwanted signal coupling from the control (IN) input to the analog (NC or NO)output. This is measured in coulomb (C) and measured by the total charge induced due to switching of the control input.Charge injection, QC = CL × ΔVCOM, CL is the load capacitance, and ΔVCOM is the change in analog output voltage.

CNC(OFF) Capacitance at the NC port when the corresponding channel (NC to COM) is OFF.CNC(ON) Capacitance at the NC port when the corresponding channel (NC to COM) is ON.CNO(OFF) Capacitance at the NC port when the corresponding channel (NO to COM) is OFF.CNO(ON) Capacitance at the NC port when the corresponding channel (NO to COM) is ON.CCOM(OFF) Capacitance at the COM port when the corresponding channel (COM to NC) is OFF.CCOM(ON) Capacitance at the COM port when the corresponding channel (COM to NC) is ON.CI Capacitance of control input (IN, EN).

OISOOFF isolation of the switch is a measurement of OFF-state switch impedance. This is measured in dB in a specificfrequency, with the corresponding channel (NC to COM) in the OFF state.

XTALK

Crosstalk is a measurement of unwanted signal coupling from an ON channel to an OFF channel (NC1 to NO1). Adjacentcrosstalk is a measure of unwanted signal coupling from an ON channel to an adjacent ON channel (NC1 to NC2). This ismeasured in a specific frequency and in dB.

BW Bandwidth of the switch. This is the frequency in which the gain of an ON channel is –3 dB below the DC gain.

THDTotal harmonic distortion describes the signal distortion caused by the analog switch. This is defined as the ratio of rootmean square (RMS) value of the second, third, and higher harmonic to the absolute magnitude of the fundamentalharmonic.

ICC Static power-supply current with the control (IN) pin at VCC or GND.


http://www.ti.com



ON-State Leakage Current

Channel ON

IN

+

+

VCC

IN

+

+

+OFF-State Leakage Current

Channel OFF

VCC

Ω

IN

+

+

VCC

16




Figure 15. ON-State Resistance (rON)

Figure 16. OFF-State Leakage Current(ICOM(OFF), INC(OFF), ICOM(PWROFF), INC(PWROFF))

Figure 17. ON-State Leakage Current(ICOM(ON), INC(ON))


http://www.ti.com



50 Ω

50 Ω

35 pF

90% 90%SwitchOutput

LogicIntput

TEST

35 pF

IN

VCC

VCC

COMCOM

NO

VBIAS

VNOCapacitance

Meter V = V or GND andBIAS CC

V = V or VI IH ILCapacitance is measured at NO,COM, and IN inputs during ONand OFF conditions.

VCC

17




Figure 18. Capacitance(CI, CCOM(OFF), CCOM(ON), CNC(OFF), CNC(ON))

All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr < 5 ns,tf < 5 ns.CL includes probe and jig capacitance.

Figure 19. Turnon (tON) and Turnoff Time (tOFF)CL includes probe and jig capacitance.All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr < 5 ns,tf < 5 ns.


http://www.ti.com



Network Analyzer Setup

Source Power = 0 dBM(632-mV P-P at 50- load)ΩDC Bias = 350 mV

Channel OFF: NO to COM

V = V or VI IH IL50 Ω

Ω

Ω

IN

+

VCC



Channel ON: NO to COM

V = V or VI IH IL

50 Ω

Ω

IN

+

VCC

VOH

NC or NO

NC or NO

V or VNC NO

V or V = VNC NO CC

R = 50L Ω

C = 35 pFL

VCC

VCC

18




Figure 20. Break-Before-Make Time (tBBM)

Figure 21. Bandwidth (BW)

Figure 22. OFF Isolation (OISO)


http://www.ti.com



Audio Analyzer

Channel ON: COM to NO V = V or V R = 600I IH IL L Ω

V = V P-P f = 20 Hz to 20 kHz C = 50 pFSOURCE CC SOURCE L

600 Ω

600 Ω

COM

NO

VCC

IN

+

x Δ

Δ

IN

VCC

VCC



Channel ON: NC to COMChannel OFF: NO to COM

V = V or VI IH IL

50 Ω NC

NO

Ω

Ω

IN

+

VCC

19




Figure 23. Crosstalk (XTALK)All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr < 5 ns,tf < 5 ns.CL includes probe and jig capacitance.

Figure 24. Charge Injection (QC)CL includes probe and jig capacitance.

Figure 25. Total Harmonic Distortion (THD)


http://www.ti.com



VCC

IN2

GND

NC1

NO1

COM1

NC2

NO2

COM2

NC3

NO3

COM3

NC4

NO4

COM4

NC5

NO5

COM5

NC6

NO6

COM6

IN1

ENLogic


20




8 Detailed Description

8.1 OverviewThe TS3A27518E is a bidirectional, 6-channel, 1:2 multiplexer-demultiplexer designed to operate from 1.65 V to3.6 V. This device can handle both digital and analog signals, and can transmit signals up to VCC in eitherdirection. The TS3A27518E has two control pins, each controlling three 1:2 muxes at the same time, and anenable pin that puts all outputs in high-impedance mode. The control pins are compatible with 1.8-V logicthresholds and are backward compatible with 2.5-V and 3.3-V logic thresholds.

8.2 Functional Block Diagram

8.3 Feature DescriptionThe isolation in power-down mode, VCC = 0 feature places all switch paths in high-impedance state (High-Z)when the supply voltage equals 0 V.

8.4 Device Functional ModesThe TS3A27518E is a bidirectional device that has two sets of three single-pole double-throw switches.Two digital signals control the 6 channels of the switch; one digital control for each set of three single-pole,double-throw switches. Digital input pin IN1 controls switches 1, 2, and 3, while pin IN2 controls switches 4, 5,and 6.

The TS3A27518 has an EN pin that when set to logic high, it places all channels into a high-impedance or HIGH-Z state. Table 2 lists the functions of TS3A27518E

Table 2. Function Table

EN IN1 IN2 NC1/2/3 TO COM1/2/3,COM1/2/3 TO NC1/2/3

NC4/5/6 TO COM4/5/6,COM4/5/6 TO NC4/5/6

NO1/2/3 TO COM1/2/3,COM1/2/3 TO NO1/2/3

NO4/5/6 TO COM4/5/6,COM4/5/6 TO NO4/5/6

H X X OFF OFF OFF OFFL L L ON ON OFF OFFL H L OFF ON ON OFFL L H ON OFF OFF ONL H H OFF OFF ON ON


http://www.ti.com



SD/MMC Memory

Card

SDIO Peripheral

(Bluetooth, WLAN,

DTV, etc)

Digital Baseband or

Apps Processor

COM1

COM2

COM3

COM4

COM5

COM6

IN1, IN2, EN

NC1

NO1

NC2

NC3

NC4

NC5

NC6

NO2

NO3

NO4

NO5

NO6

TS3A27518

VCC

VCCVCC

VCC

SDIO Port


21




9 Application and Implementation

NOTEInformation in the following applications sections is not part of the TI componentspecification, and TI does not warrant its accuracy or completeness. TI’s customers areresponsible for determining suitability of components for their purposes. Customers shouldvalidate and test their design implementation to confirm system functionality.

9.1 Application InformationThe switches are bidirectional, so the NO, NC, and COM pins can be used as either inputs or outputs.

9.2 Typical Application

Figure 26. SDIO Expander Application Block Diagram


http://www.ti.com



0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5


0

1

2

3

4

5

6

7

ON

-Sta

te R

esis

tan

ce,

r(

)O

NW

85ºC

25ºC

–40ºC

22




Typical Application (continued)9.2.1 Design RequirementEnsure that all of the signals passing through the switch are within the recommended operating ranges to ensureproper performance, see Recommended Operating Conditions.

9.2.2 Detailed Design ProcedureThe TS3A27518E can be properly operated without any external components. However, TI recommendsconnecting unused pins to the ground through a 50-Ω resistor to prevent signal reflections back into the device.TI also recommends that the digital control pins (INX) be pulled up to VCC or down to GND to avoid undesiredswitch positions that could result from the floating pin.

For the RTW package connect the thermal pad to ground.

9.2.3 Application Curve

Figure 27. ON-State Resistance vs COM Voltage (VCC = 3 V)


http://www.ti.com



0603 Cap

= VIA to GND Plane

NO

2To System

You may ground the

N.C pin or not

include a trace

IN2

NO

3

CO

M5

NO

1

CO

M6

IN1

NC

3

NC

6

N.C

.

NC

1

NC

2

COM3

Vcc

COM4

COM1

GND

COM2

NO5

NO4

NO6

NC4

EN

NC5

23




10 Power Supply RecommendationsTI recommends proper power-supply sequencing for all CMOS devices. Do not exceed the absolute maximumratings, because stresses beyond the listed ratings can cause permanent damage to the device. Alwayssequence VCC on first, followed by NO, NC, or COM. Although it is not required, power-supply bypassingimproves noise margin and prevents switching noise propagation from the VCC supply to other components. A0.1-μF capacitor is adequate for most applications, if connected from VCC to GND.

11 Layout

11.1 Layout GuidelinesTo ensure reliability of the device, TI recommends following these common printed-circuit board layoutguidelines:• Bypass capacitors should be used on power supplies, and should be placed as close as possible to the VCC

pin• Short trace-lengths should be used to avoid excessive loading• For the RTW package, connect the thermal pad to ground

11.2 Layout Example

Figure 28. WQFN Layout Recommendation


http://www.ti.com



24




12 Device and Documentation Support

12.1 Community ResourcesThe following links connect to TI community resources. Linked contents are provided "AS IS" by the respectivecontributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms ofUse.

TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaborationamong engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and helpsolve problems with fellow engineers.

Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools andcontact information for technical support.

12.2 TrademarksE2E is a trademark of Texas Instruments.All other trademarks are the property of their respective owners.

12.3 Electrostatic Discharge CautionThese devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foamduring storage or handling to prevent electrostatic damage to the MOS gates.

12.4 GlossarySLYZ022 — TI Glossary.

This glossary lists and explains terms, acronyms, and definitions.

13 Mechanical, Packaging, and Orderable InformationThe following pages include mechanical, packaging, and orderable information. This information is the mostcurrent data available for the designated devices. This data is subject to change without notice and revision ofthis document. For browser-based versions of this data sheet, refer to the left-hand navigation.


http://www.ti.com



http://www.ti.com/corp/docs/legal/termsofuse.shtml

http://www.ti.com/corp/docs/legal/termsofuse.shtml

http://e2e.ti.com

http://support.ti.com/

http://www.ti.com/lit/pdf/SLYZ022

PACKAGE OPTION ADDENDUM

www.ti.com 28-Apr-2016

Addendum-Page 1

PACKAGING INFORMATION

Orderable Device Status(1)

Package Type PackageDrawing

Pins PackageQty

Eco Plan(2)

Lead/Ball Finish(6)

MSL Peak Temp(3)

Op Temp (°C) Device Marking(4/5)

Samples

TS3A27518EPWR ACTIVE TSSOP PW 24 2000 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM -40 to 85 YL518E

TS3A27518ERTWR ACTIVE WQFN RTW 24 3000 Green (RoHS& no Sb/Br)

CU NIPDAU Level-2-260C-1 YEAR -40 to 85 YL518E

TS3A27518EZQSR ACTIVE BGAMICROSTAR

JUNIOR

ZQS 24 2500 Green (RoHS& no Sb/Br)

SNAGCU Level-1-260C-UNLIM -40 to 85 YL518E

(1) The marketing status values are defined as follows:ACTIVE: Product device recommended for new designs.LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.PREVIEW: Device has been announced but is not in production. Samples may or may not be available.OBSOLETE: TI has discontinued the production of the device.

(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availabilityinformation and additional product content details.TBD: The Pb-Free/Green conversion plan has not been defined.Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement thatlead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used betweenthe die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weightin homogeneous material)

(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuationof the previous line and the two combined represent the entire Device Marking for that device.

(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finishvalue exceeds the maximum column width.

http://www.ti.com/product/TS3A27518E?CMP=conv-poasamples#samplebuy



http://www.ti.com/productcontent

PACKAGE OPTION ADDENDUM

www.ti.com 28-Apr-2016

Addendum-Page 2

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on informationprovided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken andcontinues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

OTHER QUALIFIED VERSIONS OF TS3A27518E :

• Automotive: TS3A27518E-Q1

NOTE: Qualified Version Definitions:

• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects

http://focus.ti.com/docs/prod/folders/print/ts3a27518e-q1.html

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device PackageType

PackageDrawing

Pins SPQ ReelDiameter

(mm)

ReelWidth

W1 (mm)

A0(mm)

B0(mm)

K0(mm)

P1(mm)

W(mm)

Pin1Quadrant

TS3A27518EPWR TSSOP PW 24 2000 330.0 16.4 6.95 8.3 1.6 8.0 16.0 Q1

TS3A27518ERTWR WQFN RTW 24 3000 330.0 12.4 4.25 4.25 1.15 8.0 12.0 Q2

TS3A27518EZQSR BGA MI CROSTA

R JUNI OR

ZQS 24 2500 330.0 12.4 3.3 3.3 1.6 8.0 12.0 Q1

PACKAGE MATERIALS INFORMATION

www.ti.com 2-Nov-2016

Pack Materials-Page 1

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

TS3A27518EPWR TSSOP PW 24 2000 367.0 367.0 38.0

TS3A27518ERTWR WQFN RTW 24 3000 367.0 367.0 35.0

TS3A27518EZQSR BGA MICROSTARJUNIOR

ZQS 24 2500 336.6 336.6 28.6

PACKAGE MATERIALS INFORMATION

www.ti.com 2-Nov-2016

Pack Materials-Page 2

NOTES:

1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancingper ASME Y14.5M.

2. This drawing is subject to change without notice.

PACKAGE OUTLINE

4219135/A 11/2016

www.ti.com

WQFN - 0.8 mm max height

PLASTIC QUAD FLATPACK-NO LEAD

RTW0024B

A

0.08 C

0.1 C A B0.05 C

B

SYMM

SYMM

4.13.9

4.13.9

PIN 1 INDEX AREA

0.8 MAX

0.050.00

C

SEATING PLANE

PIN 1 ID(OPTIONAL)

2X2.5

20X 0.5

2X 2.5

1

6

18

13

7 12

24 19

2.45±0.1

24X 0.340.24

24X 0.50.3

(0.2) TYP

25

EXPOSEDTHERMAL PAD

NOTES: (continued)

3. For more information, see Texas Instruments literature number SLUA271 (www.ti.com/lit/slua271) .

EXAMPLE BOARD LAYOUT

4219135/A 11/2016

www.ti.com


RTW0024B


SYMM

SYMM

LAND PATTERN EXAMPLESCALE: 20X

( 2.45)

24X (0.6)

24X (0.24)1

6

7 12

13

18

1924

(3.8)

(0.97)

(3.8)

(0.97)

25

(R0.05) TYP

20X (0.5)

(Ø0.2) TYPVIA

0.07 MAXALL AROUND 0.07 MIN

ALL AROUNDMETAL

SOLDER MASKOPENING

SOLDER MASKOPENING

METAL UNDERSOLDER MASK

SOLDER MASK DETAILS

NON SOLDER MASKDEFINED

(PREFERRED)SOLDER MASK

DEFINED

NOTES: (continued)

4. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternatedesign recommendations.

EXAMPLE STENCIL DESIGN

4219135/A 11/2016

www.ti.com


RTW0024B


SYMM

SYMM

SOLDER PASTE EXAMPLEBASED ON 0.125 mm THICK STENCIL

EXPOSED PAD 25:78% PRINTED COVERAGE BY AREA UNDER PACKAGE

SCALE: 20X

(3.8)

(0.64) TYP

1

6

7 12

13

18

1924

25

(0.64) TYP

4X( 1.08)

(R0.05) TYP

(3.8)

20X (0.5)

24X (0.24)

24X (0.6)

METALTYP

IMPORTANT NOTICE

Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to itssemiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyersshould obtain the latest relevant information before placing orders and should verify that such information is current and complete.TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integratedcircuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products andservices.Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and isaccompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduceddocumentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statementsdifferent from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for theassociated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designersremain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers havefull and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI productsused in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, withrespect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerousconsequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm andtake appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer willthoroughly test such applications and the functionality of such TI products as used in such applications.TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended toassist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in anyway, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resourcesolely for this purpose and subject to the terms of this Notice.TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TIproducts, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specificallydescribed in the published documentation for a particular TI Resource.Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications thatinclude the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISETO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTYRIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, orother intellectual property right relating to any combination, machine, or process in which TI products or services are used. Informationregarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty orendorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of thethird party, or a license from TI under the patents or other intellectual property of TI.TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES ORREPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TOACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OFMERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUALPROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OFPRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES INCONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEENADVISED OF THE POSSIBILITY OF SUCH DAMAGES.Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, suchproducts are intended to help enable customers to design and create their own applications that meet applicable functional safety standardsand requirements. Using products in an application does not by itself establish any safety features in the application. Designers mustensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products inlife-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., lifesupport, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, allmedical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applicationsand that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatoryrequirements in connection with such selection.Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-compliance with the terms and provisions of this Notice.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265Copyright © 2017, Texas Instruments Incorporated

http://www.ti.com/sc/docs/stdterms.htm