Upload
amjad-pervaz
View
26
Download
1
Embed Size (px)
DESCRIPTION
Tools for PFB
Citation preview
TOOLS FOR PFB
1 CORDLESS SCREWDRIVER (STOCK)
Makita Cordless Drills 6280DWPE - 14.4V Cordless Driver Drill Kit
Specifications:Capacity Steel 3/8"Wood 1"Battery (Ah) 1.3No Load RPM Low 0 - 350High 0 - 1,200Length 7-9/16"Torque (in.-lbs.) 260Watt Hours 18.7Net Weight (lbs. w/battery) 3.5Shipping Weight (lbs.) 9.4
2 CIRCULAR SAW (STOCK)
Ozito Circular Saw CSL-235The Ozito Circular Saw CSL-235 has been designed to cut timber and timber and fiber cement board products and is intended for DIY use only.
An adjustable bevel allows for a variety of cuts to be made.
Integrated laser provides the
user greater accuracy cutting
2000W Motor provides more
power for cutting all types of
timber
Magnesium guard robust
safety guard which is tough
and light weight
36 Tooth blade gives a smooth
finish and clean cut
Bevel adjustment allows the user to make a variety of different cut
3 ANGLE GRINDER(STOCK)
Makita 720W 100mm Angle Grind ($78)
With a slide-switch conveniently located for easy operation, the powerful 720W motor will make short work of any jobs you have around the home or work site.
Slide switch conveniently located for easy operation
Powerful 720W motor
Ergonomic 20 degree side handle
Reliable machined bevel gears
4 SCISSORS CUTTERS(STOCK)
SHEET METAL HAND STEEL CUTTING TIN SNIPS SCISSORS CUTTERS SNIPPERS SHEAR SET
5 GRIP PLIER(STOCK)
5.1 C CLAMPS SWIVEL PADS GRIP PLIER(STOCK)
6 LINE REEL(STOCK)
Speed-Line Reel and Chalk Combos
7 MEASURING TAPE(STOCK)
Measuring Tape 15Meter (50 ft)
8 HAMMER(STOCK)Rubber Hammer
Ball Pein Hammer 2lb(stock)
9 HAND HACKSAW(STOCK)
10 LEVELSPIRIT LEVEL 450 MM MAGNETIC
11 MARKER(STOCK)
Skid with base frame manufacturing required following tools:
Gas cutting torch with gases cylinders 1Set(used from shop floor)Electric welding plant with wire and holder 1 Set(stock)Pedestal drill machine 1/2" 1 No.(used from shop floor)Hand Drill machine ½” 1 No. (stock)Drill bit 12mm 1 No.(stock)Fix Ring spanner 10mm 2 No.Hole saw HHS 32mm 1 No.Try Square 6”, 12”, 24” 3 No.Leather gloves 2 No.(stock)General gloves 6 No.(stock)
12COMMON TOOLS AND EQUIPMENT NEEDED
12.1POWER TOOLS
Rotary hammer drill (for concrete drilling up to 20mm diameter) plus SDS drill bits to suit anchor
fixing
150mm hand held grinder and metal blades to suit
Explosive powered nailing gun, preferably collated for shooting plates to concrete (plus mickey pins
and nails)
Cordless impact drivers each with driver tips to suit
185mm portable circular saw
250mm metal cut off saw and blades
12.2
12.3TOOL ACCESSORIES
15 amp electrical safety pack and electrical leads (of suitable length)
5/16" & 3/8" driver tips to suit hex type
No. 2 and No. 3 Phillips bits
18mm Spanner & socket sets
Screw gun extension bit (length up to 150mm)
12.4
12.5HAND TOOLS
Double action tin snips (2 pair each left and right hand)
2000mm spirit level and 1200mm spirit level
Pack 10 oil based marker pens (fine)
String lines (chalked and un-chalked) and line marking chalk
Adjustable G cramps/ vice grips
Measuring tapes
Hammer
Hacksaw and blades
Old carpenters chisel
Suitable cold chisel
12.6
12.7ESSENTIAL SAFETY EQUIPMENT
2400mm high step ladders
Fall protection harness
Carpenters trestles (saw horses) 750mm or 900mm high
3600mm high aluminum trestles
5000mm aluminum planks
Ply sheeting 2700mm x 1200mm x 15mm (make platform for fabrication and re-use as scaffold
deck for installation)
Eye protection
Hearing protection (when using power tools)
Protective gloves
Earth leakage circuit breaker for electrical tools
Tool You will need
Just below you'll find a list of tools to make the job of working with steel easier. Simply click on an image
to find out a brief description of the tool, plus how you can get your hands on one.
Aviation snips, Used for trimming or cutting light gauge steel, www.bunnings.com.au
Collated
screw guns - battery (plasterers), www.makita.com.au
Drilling lubricants, Used to increase the efficiency of cutting action and to enhance tool life.
Fasteners (2nd fix carpenters), Used for fixing skirting and architraves to steel frames.
Fasteners (fixers), www.buildex.com.au, www.strongtie.com.au
Used for all Steel frame fixing including flooring to steel joices.
Fasteners (plasterers), Used for fixing plasterboard to steel frames, www.aerofast.com.au
Flattening tool, Used for flattening stud or noggin flange lips for stud and noggin connection.
Grommets (electrical), www.auslec.com.au
Used to reinforce a hole and to shield electrical cable from the sharp edges of the hole.
Grommets/Snap bushes/clips (plumbing), www.shazian.com.au/janter
Used to reinforce a hole and to shield pipes from the sharp edges of the hole.
Clips are used to brace poly-piping against a frame.
Impact screw guns - battery, www.hitachi-powertools.com.au www.bosch.com.au
Used for screw fixing frames snd Fascia brackets.
Kamekura - portable electric/hydraulic hole punch, www.stainelec.com.au
Used for punching heavy gauge steel to create holes for cabling and plumbing pipes.
Magnetic level, www.bunnings.com.au
Used for plumbing or levelling steel studs, noggins, etc.
Manual hydraulic punch & tools, www.stainelec.com.au
Used for making holes in steel for plumbing and electrical grommets.
Nibbler, www.hitachi-powertools.com.au, Used for cutting light gauge steel.
Pipe and duct snips, www.blackwoods.com.au
Used for cutting slot across diameter of larger penetration holes.
Quick - Drive Pro extension, http://www.strongtie.com.au
Used as a stand-up extension to fix timber or fibreboard to joices.
Slot/straight shears, www.fein.com.au, Used for cutting light gauge steel.
Stainelec S100 hand hole punch tool, www.stainelec.com.au
Used for cutting light gauge steel to create holes for cabling and services.
Step drills, www.bunnings.com.au
Used for drilling pilot holes for receiving punch shanks in thicker materials.
Tungsten carbide hole cutters, www.stainelec.com.au
Used for more efficent hole cutting including larger penetration holes, cutting holes in boxed studs and
back to back c-channels.
Vice grip tools, www.bunnings.com.au
Used for folding light gauge steel, for example when making noggins. C-grips are used to hold pieces of
steel and/or plates in place around the stud lip when drilling.
http://tradies.truecore.com.au/toolsyoullneed