Upload
others
View
5
Download
0
Embed Size (px)
Citation preview
University of WollongongResearch Online
Faculty of Engineering and Information Sciences -Papers: Part A Faculty of Engineering and Information Sciences
1994
The interpretation of laser sensing measurementsfor blast furnace operations and controlPeter C. WallBHP Steel Group
R J TurnerBHP Steel Group
Mark HughesBHP Steel Group
Peter HukBHP Steel Group
Ross J. HaywoodBHP Steel Group
See next page for additional authors
Research Online is the open access institutional repository for the University of Wollongong. For further information contact the UOW Library:[email protected]
Publication DetailsWall, P. C., Turner, R. J., Hughes, M., Huk, P., Haywood, R. J., McCarthy, M. J. & Zulli, P. (1994). The interpretation of laser sensingmeasurements for blast furnace operations and control. Revue de Metallurgie, 91 (3), 411-420.
The interpretation of laser sensing measurements for blast furnaceoperations and control
AbstractSeveral laser-based sensors for use on blast furnaces have been developed and implemented, including araceway sensor, burden level sensor (single point) and burden surface profiler. These sensors are based on thetime-of-flight technique and give high levels of accuracy in all applications. The data obtained from the sensorsduring normal furnace operations are examined in light of the process models utilised by operators and for theinterpretation of pulverised coal injection performance. Raceway sensory data obtained during a furnaceblow-in are also discussed.
Keywordsinterpretation, measurements, laser, blast, furnace, operations, control, sensing
DisciplinesEngineering | Science and Technology Studies
Publication DetailsWall, P. C., Turner, R. J., Hughes, M., Huk, P., Haywood, R. J., McCarthy, M. J. & Zulli, P. (1994). Theinterpretation of laser sensing measurements for blast furnace operations and control. Revue de Metallurgie,91 (3), 411-420.
AuthorsPeter C. Wall, R J Turner, Mark Hughes, Peter Huk, Ross J. Haywood, M J McCarthy, and Paul Zulli
This journal article is available at Research Online: http://ro.uow.edu.au/eispapers/6700
I I
The interpretation of laser sensing measurements for blast furnace operations and control*
P.C. Wall, R.J. Turner, M. Hughes, P. Huk, R J. Haywood, M.J. McCarthy, P. Zulli (BHP Steel Group, Australia)
Several laser-based sensors for use on blast furnaces have been developed and implemented, including a raceway sensor, burden level sensor (single point) and burden surface profiler. These sensors are based on the time-of-flight technique and give high levels of accuracy in all applications. The data obtained from the sensors during normal furnace operations are examined in light of the process models utilised by operators and for the interpretation of pulverised coal injection performance. Raceway sensory data obtained during a furnace blow-in are also discussed.
Peter WALL, 36 ans. chercheur scientifiquc. Rcsponsablc du devclnppemcnt du captrur laser de zone tourbi llonnairc, travaillant dans la section des technologies d' habilitation au depanemcnt Rechcrchc dc BHP (Austral ie).
Robert TURNRR, 36 ans. cherchcur scientifiquc. Rcsponsable du dcvcloppcment de l'cquipcmcnt de detection de BHP. trnvaillant d;111s la section des tcclmologics d'hahilitation au dcpa11e111ent Rc.:hcrchc de BHP.
:\1ark HUGHF:S, JI ans. ingcnicur devcloppemcnt. Rcsponsable de la misc en place des techniques de detection tlans It's hautslnurncaux de I' us inc de Newcastle.
Peter HUK, 34 ans ingenicur dcvdoppemt!nl. Rcsponsablc de la nih.c en place de rcquipcment de dcteuion dans lcs haulslnurneaux de Port Kemhla.
Ross H /\ YWOOO. ~3 ans. do1.:1eur en genie mccanique. Rc,ponsablc des eludes sur J'inj~<:tion de charbon pulverise cl de h1 modc lisation des h:mts-fourneaux Jans la section de trnitement des mincraux du dcpartcmc nt Rcd1erchl! de BHP.
l\1alcolm McCARTHY. 53 ans. doc.:teur en genie chimique. Rcsponsablc de !'ensemble des recherches sur les ha111s-fourneaux. ,·omprenant I' injection de charbon pulverise el les programmes de prolonga tion de duree de vie dans la section de tr<1ite111ent des mincraux au depar1c1nen1 Rcd1crchc de BHP.
J>aul ZULLI, doctcur en genie chimiquc. Coordinateur des red1crc.:hcs sur !'elaboration de la fonle dans la section de trnilemcnt de~ mincrnux au dep<trlement Rechen:he de BHP. responsable de I' ensemble de la rechcrche pour I' elaboration de la fontc da~siquc
* ~11/1je1·1 1!/' lee/I/re 111 the ATS Stee!t11aki111i C011/'ere11ce j993 ( Pari.I'. 15 '/() /)ecl'111her. /993. S<w.1·io11 3).
La Revue de Metallurgie - CIT Mars 1994
1------- -------------- --------·'::•..;.·,.:\i
• INTRODUCTION
Over the last seven years, BHP has developed and implemented several laser-based sensors for use on its blast furnaces, including a raceway sensor, burden level sensor (single point) and burden surface profiler. The driving forces behind these developments relate to operator requirements of monitoring the furnace condition in a non-invasive manner and providing accurate data for control of burden distribution, peripheral gas distribution and stock level, and for associated process models. Laser range finding techniques offer the following advantages : fewer entry ports to the furnace, remote operations and improved accuracy.
This paper provides a brief review of the developments in laser-based sensing, together with a detailed examination of the data obtained during furnace operations. An analysis of the data with respect to both nonnal and abnomial (e.g. furnace blow-ins) operations is discussed. A future application of the raceway sensor for pulverised coal combustion studies in the blast furnace is also described.
• LASER-BASED SENSORS
Principle of operation.
The basic operating principle of all the laser systems employed is that of time-of-flight (TOF) laser ranging, as illustrated in figure 1. This technique uses the time taken for a short pulse of light to travel from a laser source to a target and back to a detector. The range, R, is calculated using the equation shown in figure I, where C is the velocity of light, l is the time taken for pulse to travel from source to detector and n is the refractive index of the fluid medium. Although the technique is relatively straightforward. sophisticated signal processing is required to extract the range information from the raw data.
Location of sensors on blast furnace.
Figure 2 shows the positions of the three sensors on the blast furnace. The burden level sensor (single point) or laser stock.rod is used on Newcastle No. 3 blast furnace (bell-top) as a backup for an existing mechanical stockrod, since the configuration of the furnace top does not permit the installation of another mechanical-type stockrod. The
411