Embed Size (px)
Citation preview
1www.fernox.com
TF1 TOTAL FILTERA high performance in-line system filter, which uses hydrocyclonic and magnetic action to remove all types of contaminants from central heating system water.
Product Specifications
Dimensions and weight
n Unique action, removes magnetic & non-magnetic contaminants
n Dosing point for Fernox ‘F’ range products
n All valves and fittings included
n Hydrocyclonic and magnetic in-line filter
n Fits vertical and horizontal pipework
n Cleaned in minutes without removal or disassembly
n Will not block or restrict flow
n Complies with company guidance for carbon footprint reduction and sustainability ethos
n As with all magnetic products, if you have an implanted cardiac device extra caution should be taken at all times when handling any Fernox TF1 filter
n Maximum operating temperature: 100°Cn Maximum operating pressure: 3 barn Maximum flow rate: 50 L/minn Magnetic characteristics: 9000 Gauss Neodymium magnet assemblyn Body material: Glass fibre reinforced nylon plastic
n Height: 288 mm or 11.34”
n Width: 157 mm or 6.18”
n Depth: 109 mm or 4.29”
n TF1 Total Filter with 22 mm valves: 1.53 kg
n TF1 Total Filter with 28 mm valves: 1.76 kg
V.001
TF1 Total Filter
Cleaning Guide
Inlet/Outlet Orientation Guide
2www.fernox.com
1. Using a fl at end screwdriver in the recess shown, gently lever the locking clip into the ‘unlock’ position.
1. Close inlet and outlet valves
2. Pull the inlet/outlet port approximately 3 mm away from the body to allow rotation to the required position.
2. Remove magnet
3. Push the inlet/outlet port back towards the body of the unit to prevent further rotation.
3. Open outlet and drain valves
4. Push the locking clip securely back into the ‘lock’ position.
4. Close drain valve, replace magnet and open inlet valve
V.001
59mm 92mm
288m
m
236m
m
77m
m21
1mm
157mm
109m
m
20
30
405060
80
8
654
3
2
1
Pres
sure
dro
p - ∆p
10
100
0.2
0.3
0.40.50.6
0.8
0.08
0.060.050.04
0.03
0.02
0.01
0.1
1kPabar
2
3
456
8
0.8
0.60.50.4
0.3
0.2
1
10
PSI15
28mm1”22mm3/4”
Flow Rate - Q
0.1 0.2 0.3 0.4 0.6 0.8 21 3 (m3/h)4 6
0.2 0.3 0.4 0.6 0.8 21 3 (l/s)4 6 108 20
10 20 30 400.6 0.8 21 3 (GPMUS)4 6
10 20 30 4021 3 (l/min)4 6 50 80 100 200 300 400 500 800 1000
0.02 0.03 0.04 0.06 0.10.08
10 20 30 40 60
100 200 300600.40.3
3www.fernox.com
Dosing Guide Easy dosing of Fernox Expressproducts via a TF1 Filter with aslip socket connection.Note: If the filter containsmagnetite or sludge, flush itclean with water before dosing.Refer to the cleaning guideinstructions.
?
30 sec.
TF1
TF1 TF1 TF1 TF1TF1
TF1 TF1
TF1TF1TF1 TF1
30 sec.
TF1
==
ApplicationThe Fernox TF1 Total Filter can be connected directly on to the pipework using the valve fittings provided. The Fernox TF1 Total Filter is supplied ready to install into vertical pipework with system water flowing upwards. Further installation instructions are provided with the unit.The TF1 Total Filter can be installed in any one of 24 separate orientations enabled by its unique inlet/outlet mechanism, to allow the flow to be in any direction as it passes through the unit.
Packaging, Handling and StorageIndividually packaged with all valves and detailed instructions included. No special storage requirements needed. Spare parts are available from the Fernox Sales Office by calling +44 (0) 330 100 7750
Product CodesTF1 Total Filter 22 mm - 59256 TF1 Total Filter 28 mm - 59257
Pressure Loss DataThe following information shows the pressure loss in kPa over the TF1 Total Filter under different flow rates. An average domestic central heating system flow rate of 15L/m (0.25L/s) would result in a pressure drop over the TF1 Total Filter of 1.0kPa or 0.145psi or 0.01 bar.
1.
6. 8.
2. 3.
9.
4. 5.
V.003
Product usesThe Fernox TF1 Total Filter (UK patent granted No. 2448232) is a revolutionary in-line filter, which combines hydrocyclonic action with specially designed magnet assemblies, to remove both magnetic and non-magnetic contaminants from system water and contain safely within the filter befor removal.
30 sec.
7.
