TESTREPORT

ReportNo.:D6385.01­301­47

Renderedto:

CRLaurenceCo.,Inc.

Vernon,California

PRODUCTTYPE:ArchitecturalTerraceDoor(Out­Swing)

SERIES/MODEL:900

SPECIFICATION: AAMA/WDMA/CSA101/I.S.2/A440­08,NAFS­NorthAmerican

FenestrationStandard/SpecificationforWindows,Doors,andSkylights.

Title SummaryofResults

PrimaryProductDesignator

ClassAW–PG80:SizeTested1223x

2440mm(48­5/32x96­1/16in.)

– TypeATD

DesignPressure ±3840 Pa(±80.20 psf)

AirInfiltration 0.2 L/s/m2 (0.04 cfm/ft2)

WaterPenetrationResistanceTestPressure 580Pa(12.11 psf)

TestCompletionDate: 08/18/2014

ReferencemustbemadetoReportNo.D6385.01­301­47,dated10/03/14forcompletetest

specimendescriptionanddetailedtestresults.

������������ ��� ���� �����������

��� ������������������ �������������

��������� ����� ��� �������� �� ���� !"#�$�%

TestReportNo.:D6385.01­301­47

ReportDate:10/03/14

TestRecordRetentionEndDate:08/18/18

Page1of8

1.0 ReportIssuedTo: CRLaurenceCo.,Inc.

2100East38thStreet

Vernon,California90058

2.0 TestLaboratory: ArchitecturalTesting,Inc.

4RanchoCircle

LakeForest,California92630

949­460­9600

3.0 ProjectSummary:

3.1 ProductType:ArchitecturalTerraceDoor(Out­Swing)

3.2 Series/Model:900

3.3 ComplianceStatement: Resultsobtainedaretestedvaluesandweresecuredby

using the designated test methods. The specimen tested successfully met the

performancerequirementsforaClassAW–PG80:SizeTested1223x2440mm

(48­5/32x96­1/16in.)–TypeATD rating.

3.4 TestDates:08/14/2014­08/18/2014

3.5 TestLocation: C.R.Laurence'stestfacilityinLosAngeles,California.Calibration

of test equipment was performed by Architectural Testing in accordance with

AAMA 205­01 "In­Plant Testing Guidelines for Manufacturers and Independent

Laboratories".

3.6 Test Sample Source: The test specimen was provided by the client.

Representative samples of the test specimen will be retained by Architectural

Testingforaminimumoffouryearsfromthetestcompletiondate.

3.7 Drawing Reference: The test specimen drawings have been reviewed by

ArchitecturalTestingandarerepresentativeofthetestspecimens reportedherein.

TestspecimenconstructionwasverifiedbyArchitecturalTestingperthedrawings

locatedinAppendixC.Anydeviationsaredocumentedhereinoronthedrawings.

3.8 ListofOfficialObservers:

Name Company

MarcoRamirez CRLaurenceCo.,Inc.

JarodS.Hardman ArchitecturalTesting,Inc.

��������� ����� ��� �������� �� ���� !"#�$�%

TestReportNo.:D6385.01­301­47

ReportDate:10/03/14

TestRecordRetentionEndDate:08/18/18

Page2of8

4.0 TestSpecifications:

AAMA/WDMA/CSA 101/I.S.2/A440­08, NAFS ­ North American Fenestration

Standard/SpecificationforWindows,Doors,andSkylights.

AAMA 910­10, Voluntary "Life Cycle" Specifications and Test Methods for AW Class

ArchitecturalWindowsandDoors.

5.0 TestSpecimenDescription:

5.1 ProductSizes:

OverallArea:2.84 m²(30.60 ft2)

Width Height

millimeters inches millimeters inches

Overallsize 1223 48­5/32 2440 96­1/16

Leaf 1185 46­21/32 2399 94­7/16

5.2 FrameConstruction:

FrameMember Material Description

ThresholdThermallybroken

aluminumUnionofDie#H­61266andDie#H­61267withthermalbreakDie#279300.

HeadThermallybroken

aluminumUnionofDie#H­61266andDie#H­61265withthermalbreakDie#279300.

JambsThermallybroken

aluminumUnionofDie#H­61264andDie#H­61263withthermalbreakDie#279300.

Joinery Type Detail

Allcorners Coped

Secured through jamb at each corner intoscrewbosswithtwo#12x1"Hexheadscrews,and thencorner joint is cappedwith2"x2"x4­1/2"cornercap1/32"thickissiliconesealedoverthecornerjoint.

��������� ����� ��� �������� �� ���� !"#�$�%

TestReportNo.:D6385.01­301­47

ReportDate:10/03/14

TestRecordRetentionEndDate:08/18/18

Page3of8

5.0 TestSpecimenDescription:(Continued)

5.3 Leaf Construction:

Leaf Member Material Description

Toprail,bottom

rail,stiles

Thermallybroken

aluminum

UnionofDie#H­61273andDie#H­61272with

thermalbreakDie#279300.

Joinery Type Detail

Allcorners Mitered

Securedatcornerswithaluminumcornerkey,

Die#H80000,thatissecuredtorailsandstiles

with three dimples in the aluminum to retain

thekey.

5.4 Weatherstripping:

Description Quantity Location

Hollow bulb gasket (see

attacheddrawing#USA­2964)1row

Inserted into channel of frame full

perimeter.

Foam filled bulb gasket (see

attacheddrawing#USA­1820)1row

Inserted in channel of leaf full

perimeter.

5.5 Glazing:

Glass

TypeSpacerType

Interior

Lite

Exterior

LiteGlazingMethod

1"IGAluminum

A1­D1

1/4"clear

tempered

1/4"clear

tempered

Exterior tape glazed with 3/8" x

1/8" tape and a cap bead at

interior side and secured at

exterior with glazing bead (See

attached Drawing #60939) and

rubberwedgegasket(seeattached

Drawing#USA­1819B).

Location QuantityDaylightOpening

GlassBitemillimeters inches

Leaf 1 985x2200 38­25/32x86­5/8 1/2"

��������� ����� ��� �������� �� ���� !"#�$�%

TestReportNo.:D6385.01­301­47

ReportDate:10/03/14

TestRecordRetentionEndDate:08/18/18

Page4of8

5.0 TestSpecimenDescription:(Continued)

5.6 Drainage:

DrainageMethod Size Quantity Location

Weep hole 1­3/4"x1/4" 1

Mid­spanof thresholdat exterior face

with weep hole cover inserted into

opening (see attached Drawings

#5520HS­031and5520HS­032)

Weephole 3/4"x1/8" 21" from each end of glazing pocket of

bottomrailofleaf.

5.7 Hardware:

Description Quantity Location

Hoppe Athinai M156/216N

handleassembly1

Located36"fromsillandsecuredtolock

stile with three #10 x 2­1/2" Phillips

ovalheadscrews.

Handle/deadboltstrike 1

Located directly opposite handle

assemblyonlockjambandsecuredwith

three #10 x 1/2" Phillips flat head

screws (seeattachedDrawing#900­40).

Hoppeactivetonguesystem 1

Onetonguelocated12"fromsillandthe

other tongue located 30" from head on

leaf lock stile, system was secured to

stile with #8 x 1" Phillips flat head

screws6"oncenterspacingoffulllength

ofstile.

Tonguestrike 2

Locateddirectlyoppositetongueonlock

jamb and securedwith two#10 x 1/2"

Phillips flat head screws (see attached

drawing#900­42B).

Shootboltstrike 2

Located directly opposite shoot bolt in

cornerofheadandsillat lockjamband

securedtoheadandsillwithtwo#10x

1/2" Phillips flat head screws (see

attacheddrawing#900­43C).

Butthinge 4

Located8­3/4"fromsilland26­1/4"on

center,securedto framejamb with four

#12­24 x 7/8" Phillips flat head screws

and to leaf stile with four #12 x 1"

Phillips pan head screws (see attached

drawing#900­24B).

��������� ����� ��� �������� �� ���� !"#�$�%

TestReportNo.:D6385.01­301­47

ReportDate:10/03/14

TestRecordRetentionEndDate:08/18/18

Page5of8

5.0 TestSpecimenDescription:(Continued)

5.8 Reinforcement:

DrawingNumber Location Material

C­1253Insertedintocornerjointsofleaf

assembly.Aluminum

5.9 ScreenConstruction:Noscreenwasutilized.

6.0 Installation:

ThespecimenwasinstalledintoaPinewoodbuck. Theroughopeningallowedfora

3/8"shimspace. Theexterior andinterior perimetersofthedoorframewere sealed

withstructuralsiliconesealant.

Location AnchorDescription AnchorLocation

Fullperimeter #12x2"Phillipsflatheadscrew6" from corners and 12" on

center.

��������� ����� ��� �������� �� ���� !"#�$�%

TestReportNo.:D6385.01­301­47

ReportDate:10/03/14

TestRecordRetentionEndDate:08/18/18

Page6of8

7.0 Test Results: The temperature during testing was 27°C (81°F). The results are

tabulatedasfollows:

TitleofTest Results Allowed Note

OperatingForce,

Forcetolatchtestprocedure,

perAAMA101

Forcetolatch:

26.7 N(6.0 lbf) ReportOnly

Deadbolt:

4.5 N/m (1.0 lbs/in) ReportOnly

Forcefordeadbolt:

0 N(0.0 lbf) ReportOnly

Forceforsecondary:

80.1 N(18.0 lbf) ReportOnly

AirLeakage,

InfiltrationperASTME283

at300Pa(6.27 psf)

0.2 L/s/m2

(0.03 cfm/ft2)

0.5 L/s/m2

(0.10 cfm/ft2) max. 1

WaterPenetration,

perASTME547andASTME331

at580 Pa(12.11 psf) Pass Noleakage

LifeCycleperAAMA910

DoorLeafCycling,

(Firsthalf)

perAAMA910

12,500cycles Pass Nodamage

LockingHardwareCycling,

(Firsthalf)

perAAMA910

2000cycles Pass Nodamage

MisuseTesting perAAMA910

DoorLeafVerticalLoad

at890 N(200 lbf) Pass Nodamage

DoorLeafCornerBlock

at334 N(75 lbf) Pass Nodamage

LifeCycleperAAMA910

DoorLeafCycling,

(Secondhalf)

perAAMA910

12,500cycles Pass Nodamage

LockingHardwareCycling,

(Secondhalf)

perAAMA910

2000cycles Pass Nodamage

��������� ����� ��� �������� �� ���� !"#�$�%

TestReportNo.:D6385.01­301­47

ReportDate:10/03/14

TestRecordRetentionEndDate:08/18/18

Page7of8

7.0 TestResults:(Continued)

TitleofTest Results Allowed Note

OperatingForce,

Forcetolatchtestprocedure,

perAAMA101

Forcetolatch:

40.0 N(9.0 lbf) ReportOnly

Deadbolt:

4.5 N/m (1.0 lbs/in) ReportOnly

Forcefordeadbolt:

0N(0.0 lbf) ReportOnly

Forceforsecondary:

111.2 N(25.0 lbf) ReportOnly

UniformLoadDeflection,

perASTME330

takenattoprail

+3840 Pa(+80.20 psf)

­3840 Pa(­80.20 psf)

1.3mm(0.05")

3.1mm(0.12")

6.1mm(0.24")max.

6.1mm(0.24")max. 2,3

AirLeakage,

InfiltrationperASTME283

at300Pa(6.27 psf)

0.2 L/s/m2

(0.04 cfm/ft2)

0.5 L/s/m2

(0.10 cfm/ft2)max. 1

WaterPenetration,

perASTME547andASTME331

at580Pa(12.11psf) Pass Noleakage

UniformLoadStructural,

perASTME330

takenattoprail

+5760 Pa(+120.3 psf)

­5760 Pa(­120.3 psf)

0.0mm(0.00")

0.0mm(0.00")

2.3 mm(0.09")max.

2.3mm(0.09")max. 2,3

ForcedEntryResistance,

per AAMA1304 Pass Noentry

Note 1: The tested specimen meets (or exceeds) the performance levels specified in

AAMA/WDMA/CSA101/I.S.2/A440forairleakageresistance.

Note2:Loadswereheldfor10seconds.

Note3:Tapeandfilmwereusedtosealagainstairleakageduringstructuraltesting.In

ouropinion,thetapeandfilmdidnotinfluencetheresultsofthetest.

GeneralNote:Thedoorwastestedinaccordancewiththeventinguseclassification.

��������� ����� ��� �������� �� ���� !"#�$�%

TestReportNo.:D6385.01­301­47

ReportDate:10/03/14

TestRecordRetentionEndDate:08/18/18

Page8of8

TheservicelifeofthisreportwillexpireonthestatedTestRecordRetentionEndDate,at

which timesuchmaterials asdrawings,datasheets, samplesof test specimens, copiesof

this report, and any other pertinent project documentation, shall be discarded without

notice.

If test specimen contains glazing, no conclusions of any kind regarding the adequacy or

inadequacy of the glass in any glazed test specimen can bemade. This report does not

constitutecertificationofthisproductnoranopinionorendorsementbythislaboratory.It

is the exclusivepropertyof the client sonamedherein and relates only to the specimen

tested.Thisreportmaynotbereproduced,exceptinfull,withoutthewrittenapprovalof

ArchitecturalTesting,Inc.

ForARCHITECTURALTESTING,Inc.

___________________________________________ ________________________________________________

JarodS.Hardman KennyC.White

LaboratoryManager LaboratoryManager

JSH:ss

Attachments(pages):Thisreportiscompleteonlywhenallattachmentslistedareincluded.

Appendix­A:AlterationAddendum(1)

Appendix­B:Photographs(2)

Appendix­C:Drawings(26)

ThisreportproducedfromcontrolleddocumenttemplateATI00506 issued04/25/11.

��������� ����� ��� �������� �� ���� !"#�$�%

TestReportNo.:D6385.01­301­47

ReportDate:10/03/14

TestRecordRetentionEndDate:08/18/18

AppendixA

AlterationAddendum

Note:Noalterationswererequired.

��������� ����� ��� �������� �� ���� !"#�$�%

TestReportNo.:D6385.01­301­47

ReportDate:10/03/14

TestRecordRetentionEndDate:08/18/18

AppendixB

Photographs

��������� ����� ��� �������� �� ���� !"#�$�%

TestReportNo.:D6385.01­301­47

ReportDate:10/03/14

TestRecordRetentionEndDate:08/18/18

PhotoNo.1

DoorCyclingSet­up–Interior

PhotoNo.2

DoorCyclingSet­up–Exterior

��������� ����� ��� �������� �� ���� !"#�$�%

TestReportNo.:D6385.01­301­47

ReportDate:10/03/14

TestRecordRetentionEndDate:08/18/18

PhotoNo.3

DoorCycling–CompletionofFirstHalf

PhotoNo.4

DoorCycling–CompletionofSecondHalf

��������� ����� ��� �������� �� ���� !"#�$�%

TestReportNo.:D6385.01­301­47

ReportDate:10/03/14

TestRecordRetentionEndDate:08/18/18

AppendixC

Drawings

��������� ����� ��� �������� �� ���� !"#�$�%