Upload
vuongdang
View
219
Download
1
Embed Size (px)
Citation preview
Date:20.04.2017
In figures In words In
figures
In words
1
INTERIOR DECORATION
AND ANCILLARY WORKS
FOR THE OFFICE SPACE
OF THE SOFTWARE
TECHNOLOGY PARK OF
INDIA AT SALTLAKE,
KOLKATA
BIDDER'S
FINANCIAL OFFER: Rs. (In Figure)
Rupees (In Words)
Note: The rates quoted shall be inclusive of all taxes & duties etc.
Seal & Signature of Bidder
TENDER FOR EXECUTION OF INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE
SPACE OF THE SOFTWARE TECHNOLOGY PARK OF INDIA AT SALTLAKE, KOLKATA.
NIT NO.ERO/MMD/STPI/1072 QUOTING SHEET
SL. No. DESCRIPTION ESTIMATED COST
(IN Rs.)
BIDDER'S PRICE AMOUNT IN Rs. after adding percentage
above, at par or below% QUOTE ABOVE /AT PAR/ BELOW
Rs. 93,98,525.00
Sl No
(I) INTERIOR WORKS 17,39,791.00
(II) CIVIL WORKS 5,09,224.00
(III) MODULAR FURNITURE WORK 31,71,600.00
(IV) CHAIRS 7,08,750.00
(V) ELECTRICAL WORKS 28,35,960.00
(VI) NETWORKING 4,33,200.00
TOTAL 93,98,525.00
NOTE: RATES ARE INCLUSIVE OF ALL TAXES
Abstruct of cost
SUMMARY SHEET
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE
TECHNOLOGY PARK OF INDIA AT SALTLAKE, KOLKATA.
Tender No ERO/MMD/STPI/1072 Dated 20.04.2017
PARTICULARS UNIT Total RATE Amount
1 FALSE CEILING ( Gypboard)
Providing and fixing Gypsum false ceiling as per India Gypsum specification for ceiling
with drops as per drawing including of providing and fixing G.I. Frame work as per
specification of India gypsum at a distance of 2'0" c/c both ways complete with 12.5mm
board and all necessary perimeter channels etc. No extra payment will be made for the
cutting of light points , stain glass,cove lighting etc. The measurement will be taken in
one level , rate should include the drops also, no extra amount will be paid for the drops.
The joints to be properly mended with paper tapes and gypsum compound all complete.
The rate should include the full completion of the ceiling. At the time of handing over the
site all necessary repairing work to be considered if required. The work to be completed
as per specification , approval of the Site in charge.No Drop or design(if any )will be
considered as extra measurement it will be considered flat ceiling.
SQM 646.88 650.15 420569.03
2 FALSE CEILING (24"x24" GRID FALSE CEILING)
24"x24" Grid False Ceiling ( SILHOULTE GRID ): Providing and Fixing False ceiling Grid
using hot dipped Galvonised steel sections, exposed surface chemically cleaned
capping pre-finished in baked polyster paint. Main tee of size 3000 x 32 x 24 mm at
every 1200mm c/c maximum, 1200mm cross Tee of size 1200 x 27 x 24mm at every
600mm intervals and 600 mm cross Tee of size 600 x 25 x 24mm at every 1200mm
max and 3000 x 19 x 19mm wall angle all around the wall to form grid size of 600mm x
600mm . The Main grid to be suspended to the MS frame with 2mm pre-straightened GI
wire and GI adjustable clamp and Laying of fibre wool board having Fire rating of 60 min.
as per BS 476/23 of 1987 , Noise reduction co-eff. ( NRC ) of 0.50, Light reflectance of
83%, Sound atteneuation of 32db, thermal conductivity of k=0.052 W/m, wt of 4kgs/mts
and humidity resistance of RH-95 , with paint finish of 600x600mm x 12mm thick over
the Grid. All as per the design and instructions Site in charges.
SQM 0.00 1400.00 0.00
3 PARTITION WORK
A Full ht. Solid Partition :- Providing and fixing partition framing shall consist of 2" x2" sal
wood finished section frame work @2'-0" c/c both ways Horizontally and Vertically. The
vertical alternate frames to be fixed to the ceiling with necessary fixtures. The framing
shall be finished with 12 mm thk. ply on both side and finished with 1.00 mm thk.
Laminate Should be considered up to two or three color combination. All as per design
suggested at site & intruction of Architect. The shade of laminate finish to be got
approved from EPI / Client. The skirting should be as per approved laminate as per
drawing and direction. Rate shall be inclusive of necessary hardware items, etc.
Complete. The edge beadings with steam beach wood should be finished with melamine
polish if required, frame work above false ceiling done shall not be measured but
contractor may factor it while quoting there rates as measurment up to false ceiling lvl.
All as per the design and instructions by Architects.
SQM 243.19 1500.00 364785.00
B Full ht. Glazed Partition :- Item same as 3A, and 10mm thk. glass with etching design
or one way vision film approved design, glass molding should be provided 35mm x12mm
steam beech with duly melamine polish the glass will be starting from 3'-0" ht. from floor
lvl. All as per the design and instructions by Architects.
SQM 133.26 1200.00 159912.00
C Low Ht /Half Ht Semi Glazed Partitions : Same as Item no 3 A but and above Low ht
or Half height as per design including 10 mm glass with edges polished to be used . All
other specs same as item no 2, Edges of the partition to be covered with 3"x1.5" Steam
beach wood duly mela mine polished moulding. All as per the design and instructions
Architect.
SQM 0 3389.00 0.00
(I) BOQ & ESTIMATE OF INTERIOR & FURNITURE WORKS
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE
TECHNOLOGY PARK OF INDIA AT SALTLAKE, KOLKATA.
SL No:
PARTICULARS UNIT Total RATE Amount
(I) BOQ & ESTIMATE OF INTERIOR & FURNITURE WORKS
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE
TECHNOLOGY PARK OF INDIA AT SALTLAKE, KOLKATA.
SL No:
4 MAIN Entrance Glazing with door
Full Ht. Glass Partition & Door(MEETING ROOM, AGM CABIN, CUSTOMER LOBBY
DOOR, MAIN ENTRANCE): Providing & fixing 12mm thk. toughened glass partly fixed
and openable, with approved patch fittings (ozone) including cost of floor spring , handle
locking arrangement top & bottom etc . The quoted rate should include for fixing frosted
film / one way vision film work, with approved design, PNB Logo, write up in the top two
bands of film (frosted /one way vision film) as directed by the Architects. SS handles of
size up to 450mm long best make, Glass may be fixed in a ss channel on the floor. All
as per the design and instructions by Architects.
SQM 5.35 7504.40 40148.54
5 DOOR
A Semi Glazed Door : Doors All made in 35mm thick Flush door with 1mm lamination
form both sides and 8mm plain glass with Etching / Acid texture border fixed with Steam
beach molding duly melamine polished. 35mmX 12mm steam beach Lipping to be
provided to all the edges of the door . Rate also to include the cost of Door Frame made
Steam beach wood fixed in partition or wall.. Door Frame should be fixed properly to the
Partitions, All Hardware should be of Brass / SS Brush finish with ISI mark. Hardware
includes Concealed Door closer, Cylindrical Lock, Door stopper and other standard
needs. All as per the design and instructions by Architects.
3'-0”x7'-0” NO. 14 8500.00 119000.00
B Solid Doors : Same as above, but the Door Frame should of first class hard wood best
quality steam beech wood of with out Glass. Instead of glass, matching laminate on
plywood to be used for maintaining uniform appearance. All as per the design and
instructions by Architects.
2'-6”x7'-0” NO. 6 8500.00 51000.00
5 Side and Back Unit (BACK SIDE OF OFFICER)
Providing and fixing Side Unit/ Back unit made out of 19mm
comm. board finished with 1.0mm laminate in all exposed areas
The drawers to be made out of 19mm comm. board in the front
cladded with 1.0mm laminate. sides to be made out of 12mm
comm.ply and bottom made out of 6mm comm ply duly painted in
matching tone and it should play on drawer sliding channels . The
shutters to be made out of 19mm comm. board and should play
on drawer sliding castors on powder coated channels. The
necessary locks , handles, etc to be provided . 3" high laminate
skiritng to be provide bottom side of the side and back unit.
Inside of the unit to be enamel painted in
matching tone . All the exposed edeges of the boards/plywoods
be coverd with woden lippings/mouldings duly polished all
complete.The work to be completed as per approval and
specificaion of the Site in charge.(Match to modular furniture) SQM 34.04 2000.00 68080.00
6 SOFT BOARD / NOTICE BOARD Providing and fixing soft board with necessary framework with 12mm thk. commercail
ply on top 12 jolly board to be fixed finished with fabric @Rs80 , with necessary
mouldings duly polished along the periferi.
SQM 4.86 1233.60 5995.30
7 POP
Providing and applying pop on wall & column as per required and to give a smooth
surface as per approval of the Site in charge .SQM 0 123.40 0.00
PARTICULARS UNIT Total RATE Amount
(I) BOQ & ESTIMATE OF INTERIOR & FURNITURE WORKS
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE
TECHNOLOGY PARK OF INDIA AT SALTLAKE, KOLKATA.
SL No:
8 PAINTING
a
Providing and applying Acrylic emulsion paints after removing the damaged plaster ,
replastering with 12mm thk cement morter finished with P.O.P to make the necessary
smoothnes , reparing all damages . Then two coats of Primer of approved make to be
applied finished with two or more coats of acrylic emulsion paints .The work to be
completed as per approval and satisfaction of the Site in charge.
SQM 437.74 100.00 43774.00
9 TEXTURE PAINT
Providing , spraying and applying Texture paint as per approved shade as per approval
of the Site in charge. Bi colour texture paint will be used. The wall surface has to duly
prepared by scraping , removing the damaged plaster and applying P.O.P to give a
smooth surface as per approval of the Site in charge.
SQM 58.36 120.00 7003.20
10SYNTHETIC ENAMEL PAINT : FOR WINDOW GRILL, ROLLING SHUTTER &
COLLAPSEABLE GATESQM 97.27 123.36 11999.23
11 Centre Table
Providing centre table as per drawing &approval of the Site in charge . Nos 2 5600.00 11200.00
12 Side Table
Providing centre table as per drawing &approval of the Site in charge . (22"x22"
avarage)Nos 4 4500.00 18000.00
13 PILLAR and WALL PANELLING
Providing & fixing in position column and wall cladding consisting of 12mm thk solid ply
and 2" X 1" hard wood section finished with 1mm laminate. SQM 0 1989.00 0.00
Providing & fixing in position column and wall cladding consisting of 12mm thk solid ply
and 2" X 1" hard wood section finished with 4mm veneer.SQM 0 2421.00 0.00
14 VERTICAL Blinds
Providing and fixing vertical blinds of approved design and shade by the Site in
charge,incl all std fittings as per manufacturer's specification.SQM 101.65 1542.00 156744.30
15 WALL DISPLAY BEHIND VISITOR AREA
Structure made by 18mm plywood and gypsum board 6" depth boxing ,finish with imm
laminate, splot light,flower vase, abstrac paintings as per drawings.SQM 19.45 31.61 614.81
16 BACK DROP BEHIND RECEPTION AREA
Structure made by 19mm plywood and gypsum board finish with laminate/veneer, and
10mm frosted glass panelling with splot light,flower vase, abstrac paintings as per
drawings.
SQM 6.80 3598.00 24466.40
17Planter box made by 19mm block board with 1mm thk. Laminate finish,Plants as per
approval of the Site in charge and provision to be fix itNos 8 2500.00 20000.00
18 Insulation of existing AC DUCT
Supply, Fixing and testing of nitrile rubber insulation (Closed cell elastometruic nitrile
rubber of class 'O' Insulation - 13 mm thickness ) on existing duct. The joint shall sealed
with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape. Insulation complete in
all respect as per site condition.
Approved make: Armacell / K-flex/ Aeroflex
SQM 366.97 545.00 200000.00
19 Rubberized vinyl FLOORING
Providing and fixing 8.0mm thick Rubberized vinyl FLOORING complete in all respect
as per Site in charge choice in Gym SQM 10.70 1542.00 16499.40
1739791.21
1739791.00
TOTAL
SAY,
Sl.No DESCRIPTION Unit Qnty. Rate Amount
Rs. Rs.
1
FLOORING
i VINYL Flooring
1.5 MM THICK PVC TILE FLOORING AS PER MANUFACTURERS
SPECIFICATION.
Size of Tile 300x300mm Sqmtr. 614.31 763.96 4,69,308.27
ii VERTICAL Ceramic Skirting
Providing and fixing 1st quality ceramic glazed wall tile, cnforiming to I.S
15622 (thickness) to be spexcified by the manufacture) of approved make
in all colors, shades except burgundry, bottle, green, black of any size as
approved - in engineers charges, in skriting, risers of steps and dados.
fixing with cement based high polymer modified quick-set tile adhesive
(water based) conforming to -15477, in average 3mm thickness.
Size of Tile 300x300 mm Sqmtr. 634.84 0 -
2
Providing and laying Vitrified tiles in different sizes (thickness to be
specified by the manufacturer), with water absorption less than 0.08%
and conforming to IS: 15622, of approved brand & manufacturer, in all
colours and shade, in skirting, riser of steps, laid with cement based high
polymer modified quick set tile adhesive (water based) conforming to IS:
15477, in average 6 mm thickness, including grouting of joints
(Paymentfor grouting of joints to be made separately).
Size of Tile 600x600 mm Sqmtr. 20.53 1240.60 25,469.52
3
Providing and fixing 18 mm thick gang saw cut, mirror polished,
premoulded and prepolished, machine cut for kitchen platforms, vanity
counters, window sills , facias and similar locations of required size,
approved shade, colour and texture laid over 20 mm thick base cement
mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement,
mixed with matching pigment, epoxy touch ups, including rubbing,
curing, moulding and polishing to edges to give high gloss finish etc.
complete at all levels.
Area of slab over 0.50 sqm Sqmtr. 4.64 3113.30 14,445.71
5,09,223.50
5,09,224.00
(II) BOQ & ESTIMATE OF CIVIL WORK
TOTAL
SAY,
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE
TECHNOLOGY PARK OF INDIA AT SALTLAKE, KOLKATA.
Sl.
No.Descriptions Unit Qnty. Rate Amount
MODULAR FURNITURE
1 WORKSTATION -LINEAR TYPE (1200L x 600D x 1200H mm)
Manufacture, supply and Installation in position 'Linear' shape unit as directed Modular workstation
comprising of partitions, work surface, gable end with all accessories etc.Nos 37 32,800.00 12,13,600.00
TABLE SIZES
a) (1200 (L) x 600 (D) x 750mm (H)
i) Tile based Partitions
Vertical partition members made of aluminium extrusion alloy of minimum 50x50mm size having
thickness of min 1.2mm for vertical members and that of 1.00mm thick for horizontal members duly
finished with powder coating in desired shade/colour. Both the faces of vertical partition to be fiished with
laminate/fabric panels. Top caps of partition shall be slightly curved/flat shape of aluminium alloy duly
finished with powder coating in desired shade/colour. The partition should have the raceways for carrying
voice and data wire and power cable, which sholuld be separate from each other in the panel. The panel
above the work surface should be on tackable board with fabric panels have fire rating as per NFPA 701
or equivalent fire code. Fabric to be used shall be min. of grade 3. The height of partition shall be of min.
1200mm. All partition should have the provision of level adjuster to adjust the height of + 10mm. All
metal components will be finished with powder coated in desired shalde/colour.100-150mm high metal
skirting
a)1200mm min. high partition with laminate finish below the worktop, fabric above work top towards
Outside of Workstation along corridor / Pasaage
b)1200mm min. high partition with laminate finish below the worktop,1Nos.White Marker writing board and
1Nos. Soft Pinup board above worktop inside of Per workstation.
c)1200mm min. high partition with laminate finish below the worktop, fabric above work top towards Inside
and Outside of Workstation in return partition / handshake Only end to end of workstation.
ii) Work Top
1)Worktop shall be of 25mm thick prelaminated particle board with 2mm thick PVC edge band lipping to all
exposed area.
2) Thickness of lamination will be 0.08mm for work top and 0.06mm for under side of work top.
3)Work top shall have 2mm PVC edging of approved make quality shade and colour on exposed area and
1mm on covered area.
4)
The top shall be supported with suitable M.S. bracket of standard size made of CRCA sheet of minimum
2mm thick Grade D as per IS 513 with power coated finish of approved colour. Suitable size of metal
insert to be provided in worktop for fixing with the partition/gable end. Fixing directly with screws is not
permissible.
5) Powder coating will be in Epoxy powder coating will be minimum 50 micron.
6)Gable Ends shall be of 25mm thick prelaminated particle board with 2mm thick PVC edge band lipping
to all exposed area.
7)Gable end Bracket will be of minmum 2.0mm thick CRCA steel Grade D as per IS 513 with metal insert.
8)Round Wire manager for wire management od dia 60-70mm shall be finished same as per table top.
9)Glass Separator - 8mm thick toughened plain clear glass separator for privacy / separate in between
two workstations in inlane shape (Linear Workstation)
10) "D" Bracket for Glass Separator power coated finish of approved colour
i)Levellers – Each frame is provided with two Nos. 12mm long leveling bolts which allow 10-25mm
adjustment for floor unevenness if any.
ii)Writing Board : Made out of 6mm thick MDF board with 0.80mm glossy highly wear resistant face
laminate with fixing of laminate of 0.80mm thick on the back.
iii)
Tile Specifications- Laminated Tile-Made of 9mm Prelamianted Particle Board ,Edges sealed with black
primer ,Fabric tile made of 9mm Particle board wrapped with fabric,Soft pinup tiles are made up of 4mm
MDF pasted with 4mm thick crosslinked foam with fabric warpped on tile.
iv)All works mentioned/described above required to be completed in all respect as per drawings &
instruction of Engineer-in-Charge.
v) 3 drawer pedestal with levellors
Prelaminated 3Drawer Pedestal (2B+1F) 406Lx450Dx685Ht. Carcass & Facia made up of 18mm thick
Pre-laminated particle board. Back Panel from 9mm PPB. All exposed edges are sealewd with 2mm
thick PVC edge-band & Non-exposed edges with 0.8mm thick PVC edge-band of Rehau. Drawers made
up of 0.8mm thick CRCA sheet. All Metal Parts are powder-cvoated through seven tank process of
powder coating.
vi) Metal Keyboard Pull Out Tray
Key board drawer for work surface shall be totally metallic and shall be mounted on table top. The key
board drawer should move on telescopic channels for smooth operation and shall be fixed to work
surface. Keyboard tray is made up of 0.6-1.0mm thick CRCA sheet duly powder coated 45-60 micron
thickness on metal surface of approved shade. The Key board tray should run below the table for
smooth movement.
vii) CPU Trolley
The Unit shall be of 240mm heigh with adjustable width from 220 to 320mm made of 1.0-2.-mm thick
CRCA steel sheet duly epoxy powder coated of 45-60 micron thickness having high density @ 70-75
Kg/Cum cross linked polyethylene foam spacers of 8mm thick and 2 nos. lockable castors & 2 Nos. non
lockable castors.
2 WORKSTATION -LINEAR TYPE (1350L x 600D x 1200H mm)
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE TECHNOLOGY
PARK OF INDIA AT SALTLAKE, KOLKATA.
(III) BOQ & ESTIMATE MODULAR FURNITURE WORKS
Sl.
No.Descriptions Unit Qnty. Rate Amount
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE TECHNOLOGY
PARK OF INDIA AT SALTLAKE, KOLKATA.
(III) BOQ & ESTIMATE MODULAR FURNITURE WORKS
Manufacture, supply and Installation in position 'Linear' shape unit as directed Modular workstation
comprising of partitions, work surface, gable end with all accessories etc.Nos 0 34,500.00 0.00
TABLE SIZES
a) (1350 (L) x 600 (D) x 750mm (H)
i) Tile based Partitions
Vertical partition members made of aluminium extrusion alloy of minimum 50x50mm size having
thickness of min 1.2mm for vertical members and that of 1.00mm thick for horizontal members duly
finished with powder coating in desired shade/colour. Both the faces of vertical partition to be fiished with
laminate/fabric panels. Top caps of partition shall be slightly curved/flat shape of aluminium alloy duly
finished with powder coating in desired shade/colour. The partition should have the raceways for carrying
voice and data wire and power cable, which sholuld be separate from each other in the panel. The panel
above the work surface should be on tackable board with fabric panels have fire rating as per NFPA 701
or equivalent fire code. Fabric to be used shall be min. of grade 3. The height of partition shall be of min.
1200mm. All partition should have the provision of level adjuster to adjust the height of + 10mm. All
metal components will be finished with powder coated in desired shalde/colour.100-150mm high metal
skirting
a)1200mm min. high partition with laminate finish below the worktop, fabric above work top towards
Outside of Workstation along corridor / Pasaage
b)1200mm min. high partition with laminate finish below the worktop,1Nos.White Marker writing board and
1Nos. Soft Pinup board above worktop inside of Per workstation.
c)1200mm min. high partition with laminate finish below the worktop, fabric above work top towards Inside
and Outside of Workstation in return partition / handshake Only end to end of workstation.
ii) Work Top
1)Worktop shall be of 25mm thick prelaminated particle board with 2mm thick PVC edge band lipping to all
exposed area.
2) Thickness of lamination will be 0.08mm for work top and 0.06mm for under side of work top.
3)Work top shall have 2mm PVC edging of approved make quality shade and colour on exposed area and
1mm on covered area.
4)
The top shall be supported with suitable M.S. bracket of standard size made of CRCA sheet of minimum
2mm thick Grade D as per IS 513 with power coated finish of approved colour. Suitable size of metal
insert to be provided in worktop for fixing with the partition/gable end. Fixing directly with screws is not
permissible.
5) Powder coating will be in Epoxy powder coating will be minimum 50 micron.
6)Gable Ends shall be of 25mm thick prelaminated particle board with 2mm thick PVC edge band lipping
to all exposed area.
7)Gable end Bracket will be of minmum 2.0mm thick CRCA steel Grade D as per IS 513 with metal insert.
8)Round Wire manager for wire management od dia 60-70mm shall be finished same as per table top.
9)Glass Separator - 8mm thick toughened plain clear glass separator for privacy / separate in between
two workstations in inlane shape (Linear Workstation)
10) "D" Bracket for Glass Separator power coated finish of approved colour
i)Levellers – Each frame is provided with two Nos. 12mm long leveling bolts which allow 10-25mm
adjustment for floor unevenness if any.
ii)Writing Board : Made out of 6mm thick MDF board with 0.80mm glossy highly wear resistant face
laminate with fixing of laminate of 0.80mm thick on the back.
iii)
Tile Specifications- Laminated Tile-Made of 9mm Prelamianted Particle Board ,Edges sealed with black
primer ,Fabric tile made of 9mm Particle board wrapped with fabric,Soft pinup tiles are made up of 4mm
MDF pasted with 4mm thick crosslinked foam with fabric warpped on tile.
iv)All works mentioned/described above required to be completed in all respect as per drawings &
instruction of Engineer-in-Charge.
v) 3 drawer pedestal with levellors
Prelaminated 3Drawer Pedestal (2B+1F) 406Lx450Dx685Ht. Carcass & Facia made up of 18mm thick
Pre-laminated particle board. Back Panel from 9mm PPB. All exposed edges are sealewd with 2mm
thick PVC edge-band & Non-exposed edges with 0.8mm thick PVC edge-band of Rehau. Drawers made
up of 0.8mm thick CRCA sheet. All Metal Parts are powder-cvoated through seven tank process of
powder coating.
vi) Metal Keyboard Pull Out Tray
Key board drawer for work surface shall be totally metallic and shall be mounted on table top. The key
board drawer should move on telescopic channels for smooth operation and shall be fixed to work
surface. Keyboard tray is made up of 0.6-1.0mm thick CRCA sheet duly powder coated 45-60 micron
thickness on metal surface of approved shade. The Key board tray should run below the table for
smooth movement.
vii) CPU Trolley
The Unit shall be of 240mm heigh with adjustable width from 220 to 320mm made of 1.0-2.-mm thick
CRCA steel sheet duly epoxy powder coated of 45-60 micron thickness having high density @ 70-75
Kg/Cum cross linked polyethylene foam spacers of 8mm thick and 2 nos. lockable castors & 2 Nos. non
lockable castors.
3 WORKSTATION -CURVELINEAR TYPE (1500L x 1350W x 600D x 1200H mm)
Manufacture, supply and Installation in position 'L' shape unit as directed Modular workstation
comprising of partitions, work surface, gable end with all accessories etc.Nos 9 44,000.00 3,96,000.00
TABLE SIZES
a) (1500 (L) x 1350 (W) x 600 (D) x 750mm (H)
Sl.
No.Descriptions Unit Qnty. Rate Amount
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE TECHNOLOGY
PARK OF INDIA AT SALTLAKE, KOLKATA.
(III) BOQ & ESTIMATE MODULAR FURNITURE WORKS
i) Tile based Partitions
Vertical partition members made of aluminium extrusion alloy of minimum 50x50mm size having
thickness of min 1.2mm for vertical members and that of 1.00mm thick for horizontal members duly
finished with powder coating in desired shade/colour. Both the faces of vertical partition to be fiished with
laminate/fabric panels. Top caps of partition shall be slightly curved/flat shape of aluminium alloy duly
finished with powder coating in desired shade/colour. The partition should have the raceways for carrying
voice and data wire and power cable, which sholuld be separate from each other in the panel. The panel
above the work surface should be on tackable board with fabric panels have fire rating as per NFPA 701
or equivalent fire code. Fabric to be used shall be min. of grade 3. The height of partition shall be of min.
1200mm. All partition should have the provision of level adjuster to adjust the height of + 10mm. All
metal components will be finished with powder coated in desired shalde/colour.100-150mm high metal
skirting
a)1200mm min. high partition with laminate finish below the worktop, fabric above work top towards
Outside of Workstation along corridor / Pasaage
b)1200mm min. high partition with laminate finish below the worktop,1Nos.White Marker writing board and
1Nos. Soft Pinup board above worktop inside of user Per workstation.
c)1200mm min. high partition with laminate finish below the worktop, fabric above work top towards Inside
and Outside of Workstation in return partition / handshake Only end to end of workstation.
ii) Work Top
1)Worktop shall be of 25mm thick prelaminated particle board with 2mm thick PVC edge band lipping to all
exposed area.
2) Thickness of lamination will be 0.08mm for work top and 0.06mm for under side of work top.
3)Work top shall have 2mm PVC edging of approved make quality shade and colour on exposed area and
1mm on covered area.
4)
The top shall be supported with suitable M.S. bracket of standard size made of CRCA sheet of minimum
2mm thick Grade D as per IS 513 with power coated finish of approved colour. Suitable size of metal
insert to be provided in worktop for fixing with the partition/gable end. Fixing directly with screws is not
permissible.
5) Powder coating will be in Epoxy powder coating will be minimum 50 micron.
6)Gable Ends shall be of 25mm thick prelaminated particle board with 2mm thick PVC edge band lipping
to all exposed area.
7)Gable end Bracket will be of minmum 2.0mm thick CRCA steel Grade D as per IS 513 with metal insert.
8)Round Wire manager for wire management od dia 60-70mm shall be finished same as per table top.
9)Glass Separator - 8mm thick toughened plain clear glass separator for privacy / separate in between
two workstations in inlane shape (Curvelinear Workstation)
10) "D" Bracket for Glass Separator power coated finish of approved colour
i)Levellers – Each frame is provided with two Nos. 12mm long leveling bolts which allow 10-25mm
adjustment for floor unevenness if any.
ii)Writing Board : Made out of 6mm thick MDF board with 0.80mm glossy highly wear resistant face
laminate with fixing of laminate of 0.80mm thick on the back.
iii)
Tile Specifications- Laminated Tile-Made of 9mm Prelamianted Particle Board ,Edges sealed with black
primer ,Fabric tile made of 9mm Particle board wrapped with fabric,Soft pinup tiles are made up of 4mm
MDF pasted with 4mm thick crosslinked foam with fabric warpped on tile.
iv)All works mentioned/described above required to be completed in all respect as per drawings &
instruction of Engineer-in-Charge.
v) 3 drawer pedestal with levellors
Prelaminated 3Drawer Pedestal (2B+1F) 406Lx450Dx685Ht. Carcass & Facia made up of 18mm thick
Pre-laminated particle board. Back Panel from 9mm PPB. All exposed edges are sealewd with 2mm
thick PVC edge-band & Non-exposed edges with 0.8mm thick PVC edge-band of Rehau. Drawers made
up of 0.8mm thick CRCA sheet. All Metal Parts are powder-cvoated through seven tank process of
powder coating.
vi) Metal Keyboard Pull Out Tray
Key board drawer for work surface shall be totally metallic and shall be mounted on table top. The key
board drawer should move on telescopic channels for smooth operation and shall be fixed to work
surface. Keyboard tray is made up of 0.6-1.0mm thick CRCA sheet duly powder coated 45-60 micron
thickness on metal surface of approved shade. The Key board tray should run below the table for
smooth movement.
vii) CPU Trolley
The Unit shall be of 240mm heigh with adjustable width from 220 to 320mm made of 1.0-2.-mm thick
CRCA steel sheet duly epoxy powder coated of 45-60 micron thickness having high density @ 70-75
Kg/Cum cross linked polyethylene foam spacers of 8mm thick and 2 nos. lockable castors & 2 Nos. non
lockable castors.
4 DIRECTOR CABIN TABLE (2500L x 2100D x 750H mm)
Manufacture, supply and Installation in position 'L' shape unit as directed Modular workstation , work
surface, Gable end, leteral filing storage units, Back Storage, Book Case and with all accessories etc. Nos 1 1,75,000.00 1,75,000.00
TABLE SIZES
a) (2550 (L) x 900 (W) x 750mm (H)
Sl.
No.Descriptions Unit Qnty. Rate Amount
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE TECHNOLOGY
PARK OF INDIA AT SALTLAKE, KOLKATA.
(III) BOQ & ESTIMATE MODULAR FURNITURE WORKS
i) Work Top
1)
Table Top is made of 29mm (25+4) thick mm MDF PVC folied Melamine Top with soft water fall edges
covered with 4mm thcik painted glass.
2)
Main Table top is supported on gable ends made of 25mm thick MDF pvc foiled with soft water fall edge
Decorated Anodised section at front and back side.
3)
Modesty Panel made of 33mm thick MDF with designer pattern. The table consiist Levellor: It also have
adjustable Leveler with plastic base with height adjustment up to 15mm.
4) The top shall be supported with suitable M.S. bracket of standard size made of CRCA sheet of minimum
2mm thick Grade D as per IS 513 with power coated finish of approved colour. Suitable size of metal
insert to be provided in worktop for fixing with the partition/gable end. Fixing directly with screws is not
permissible.
5) Gable end Bracket will be of minmum 2.0mm thick CRCA steel Grade D as per IS 513 with metal insert.
ii) Lateral Filing Storage (Return)
One lateral filing bin of size 1200(L)x450(D)x670(H)mm. Combo storage with three drawers and One
shutter and one Open with good storage capacity usable as return storage for office storage.
Carcass :- Storage Top 25mm thick with Melamine Finish,and Side Panel, Shutters and Skirting are
made up of 18mm thick PVC foiled MDF. Bottom, Vertical Panel & Shelf are made up of 18mm thick Pre-
laminated Particle board with proper grooving done near to back side edge for fitment of back panel
made up of 9mm thick prelaminated particle board. The Side panel, Bottom and Top panel are to be
assembled with the help of wooden dowel, knock down fittings Drum with screw and corner fittings to
ensure stability of box structure formed. There Is provision for a pedestal structure at Middle (i.e. Two
Book drawer and one file drawer) and two Open able storage placed on two sides with adjustable shelf
within. Drawer :- Provision of two book Drawer of size 321(W) X 400(D) X 80(H) and one File Drawer of
size 321(W) X 400(0) X 225(H) made up of 12mm thick Prelaminated Particle board with bottom panel
of 9mm thickness. The small drawers are mounted on Telescopic slide with 3/4 extension. where Big
Drawer mounted on Telescopic slide with full extension allowing storage of files with the help of file
manager. Drawer facia made up of 18mm thick PVC foiled MDF board. Provision of centralize locking
for all three drawers and Thumb Knob from Stainless Steel of 303 grade as handles. Storage Legs:-
Brown 50x50x1.6 Aluminum Powder Coated Square Legs. Storage Handles:- Square Chrome Finished
Knob.
iii) Low Height Storage Use as Back Storage
Low Height Storage of Size 1200(W)X450(D)X670(H) - 2Nos. Office Table height storage with Three
openable shutters, usable as Back unit. Carcass :- Storage Top 25mm thick with Melamine Finish, Side
Panel and Skirting are made up of 18mm thick PVC foiled MDF. Bottom Panel are made up of 18mm
thick Pre-laminated Partide board with proper grooving done near to back side edge for fitment of back
panel made up of 9mm thick prelaminated particle board.
Shelf and Shutter :- One Fixed shelf made up of 18mm thick Pre-laminated particle board & Three
shutters made up of 18mm thick Pre-laminated MDF mounted on 0 crank hinges with the Provision of
SS Thumb knob as handle. Both the stutters are lockable with the help of multipurpose square
lock.Storage Legs:- Brown 50x50x1.6 Aluminum Powder Coated Square Legs. Storage Handles:-
Square Chrome Finished Knob.
iv) Book Case 1200Lx450Dx1800H
Book Case of Size 1200(W)X450(D)X1800(H) - 2Nos. Full Height Book Case with Six openable
shutters, Carcass :- Storage Top 25mm thick with Melamine Finish, Side Panel and Skirting are made
up of 18mm thick PVC foiled MDF. Bottom Panel are made up of 18mm thick Pre-laminated Partide
board with proper grooving done near to back side edge for fitment of back panel made up of 9mm thick
prelaminated particle board. Three Compartment are open at the middle of the storage. Shelf and
Shutter :- One Fixed shelf made up of 18mm thick Pre-laminated particle board & Six shutters made up
of 18mm thick Pre-laminated MDF mounted on 0 crank hinges with the Provision of SS Thumb knob as
handle. Both the stutters are lockable with the help of multipurpose square lock.Storage Legs:- Brown
50x50x1.6 Aluminum Powder Coated Square Legs. Storage Handles:- Square Chrome Finished Knob.
v)Storage Legs – Each storage is provided with four Nos. 50x50x1.6 Aluminum Powder Coated Square
Legs adjustment for floor unevenness if any.
vi)All works mentioned/described above required to be completed in all respect as per drawings &
instruction of Engineer-in-Charge.
Sl.
No.Descriptions Unit Qnty. Rate Amount
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE TECHNOLOGY
PARK OF INDIA AT SALTLAKE, KOLKATA.
(III) BOQ & ESTIMATE MODULAR FURNITURE WORKS
5 OFFICER CABIN TABLE (1800L x 1800D x 750H mm)
Manufacture, supply and Installation in position 'L' shape unit as directed Modular workstation , work
surface, Gable end, leteral filing storage units, Back Storage, and with all accessories etc.Nos 3 85,000.00 2,55,000.00
TABLE SIZES
a) (1800 (L) x 900 (D) x 750mm (H)
i) Work Top
1)
Table Top is made of 29mm (25+4) thick mm MDF PVC folied Melamine Top with soft water fall edges
covered with 4mm thcik painted glass.
2)
Main Table top is supported on gable ends made of 25mm thick MDF pvc foiled with soft water fall edge
Decorated Anodised section at front and back side.
3)
Modesty Panel made of 33mm thick MDF with designer pattern. The table consiist Levellor: It also have
adjustable Leveler with plastic base with height adjustment up to 15mm.
4) The top shall be supported with suitable M.S. bracket of standard size made of CRCA sheet of minimum
2mm thick Grade D as per IS 513 with power coated finish of approved colour. Suitable size of metal
insert to be provided in worktop for fixing with the partition/gable end. Fixing directly with screws is not
permissible.
5) Gable end Bracket will be of minmum 2.0mm thick CRCA steel Grade D as per IS 513 with metal insert.
ii) Lateral Filing Storage (Return)
One lateral filing bin of size 1200(L)x450(D)x670(H)mm. Combo storage with three drawers and One
shutter and one Open with good storage capacity usable as return storage for office storage.
Carcass :- Storage Top 25mm thick with Melamine Finish,and Side Panel, Shutters and Skirting are
made up of 18mm thick PVC foiled MDF. Bottom, Vertical Panel & Shelf are made up of 18mm thick Pre-
laminated Particle board with proper grooving done near to back side edge for fitment of back panel
made up of 9mm thick prelaminated particle board. The Side panel, Bottom and Top panel are to be
assembled with the help of wooden dowel, knock down fittings Drum with screw and corner fittings to
ensure stability of box structure formed. There Is provision for a pedestal structure at Middle (i.e. Two
Book drawer and one file drawer) and two Open able storage placed on two sides with adjustable shelf
within. Drawer :- Provision of two book Drawer of size 321(W) X 400(D) X 80(H) and one File Drawer of
size 321(W) X 400(0) X 225(H) made up of 12mm thick Prelaminated Particle board with bottom panel
of 9mm thickness. The small drawers are mounted on Telescopic slide with 3/4 extension. where Big
Drawer mounted on Telescopic slide with full extension allowing storage of files with the help of file
manager. Drawer facia made up of 18mm thick PVC foiled MDF board. Provision of centralize locking
for all three drawers and Thumb Knob from Stainless Steel of 303 grade as handles. Storage Legs:-
Brown 50x50x1.6 Aluminum Powder Coated Square Legs. Storage Handles:- Square Chrome Finished
Knob.
iii) Low Height Storage Use as Back Storage
Low Height Storage of Size 1200(W)X450(D)X670(H) - 2Nos. Office Table height storage with Three
openable shutters, usable as Back unit. Carcass :- Storage Top 25mm thick with Melamine Finish, Side
Panel and Skirting are made up of 18mm thick PVC foiled MDF. Bottom Panel are made up of 18mm
thick Pre-laminated Partide board with proper grooving done near to back side edge for fitment of back
panel made up of 9mm thick prelaminated particle board.
Shelf and Shutter :- One Fixed shelf made up of 18mm thick Pre-laminated particle board & Three
shutters made up of 18mm thick Pre-laminated MDF mounted on 0 crank hinges with the Provision of
SS Thumb knob as handle. Both the stutters are lockable with the help of multipurpose square
lock.Storage Legs:- Brown 50x50x1.6 Aluminum Powder Coated Square Legs. Storage Handles:-
Square Chrome Finished Knob.
iv)Storage Legs – Each storage is provided with four Nos. 50x50x1.6 Aluminum Powder Coated Square
Legs adjustment for floor unevenness if any.
v)All works mentioned/described above required to be completed in all respect as per drawings &
instruction of Engineer-in-Charge.
6 OFFICER LOW HEIGHT CABIN TABLE (1650L x 1950D x 750H mm)
Manufacture, supply and Installation in position 'L' shape unit as directed Modular workstation , work
surface, Gable end, leteral filing storage units, and with all accessories etc.Nos 2 37,000.00 74,000.00
TABLE SIZES
a) (1650 (L) x 750 (D) x 750mm (H)
i) Work Top
1)
Table Top :- 30mm thick Table top made up of 18mm thick Pre-laminated Particle board with 12mm
thick thin PVC foil wrapped decorative profile made up of MDF fixed along all the edges from bottom
side which provide decorative waterfall edge profile to top with twin color look the decorative trim to be
connected at the angle ofrt 45Degree with each other.M.S. T-Hat of 0.8mm thickness is provided for
extra support for the Top of length 1200mm and above.
2)LEG :- 25mm thick Leg or Gable End made up of 25mm thick Pre-laminated Particle board with M.S.
Leveler bracket to give floating look.
Sl.
No.Descriptions Unit Qnty. Rate Amount
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE TECHNOLOGY
PARK OF INDIA AT SALTLAKE, KOLKATA.
(III) BOQ & ESTIMATE MODULAR FURNITURE WORKS
3)Work top shall have 2mm PVC edging of approved make quality shade and colour on exposed area and
1mm on covered area.
4)
The top shall be supported with suitable M.S. bracket of standard size made of CRCA sheet of minimum
2mm thick Grade D as per IS 513 with power coated finish of approved colour. Suitable size of metal
insert to be provided in worktop for fixing with the partition/gable end. Fixing directly with screws is not
permissible.
5)
Modesty :- Modesty Panel made up of 18mm thick Pre-laminated Particle board providing stability leg
privacy to user. "D" headed to structure and allow sufficient Decorative aluminum profile fixed on it , the
aluminum profile to be fixed by making grove in panel for better fixing and integrated look.
i)Levellers – Each frame is provided with two Nos. 12mm long leveling bolts which allow 10-25mm
adjustment for floor unevenness if any.
ii)All works mentioned/described above required to be completed in all respect as per drawings &
instruction of Engineer-in-Charge.
iii) Lateral Filing Storage (Return)
One lateral filing bin of size 1200(L)x450(D)x675(H)mm. - 1Nos. Office Table Height Combo storage
with three drawers and Two shutters with good storage capacity usable as return storage for office
storage. Top :-28mm thick top made up of 18mm thick Pre-laminated Particle board with 8mm thick thin
PVC foil wrapped decorative profile made up of MDF fixed along all the edges from bottom side which
provide decorative waterfall edge profile to top with twin color look the decorative trim to be connected at
the angle of 45Degree with each other. Carcass :- Side Panel, Verticals, Bottom, Skirting Panel, Shelf
and Shutters are made up of 18mm thick Pre-laminated Particle board with proper grooving done near
to back side edge of side panel and Bottom for fitment of back panel made up of 9mm thick
prelaminated particle board. There is provision for a pedestal structure (i.e. Two Book drawer and one
file drawer) and two Openable storage place with adjustable shelf within.Drawer :- Provision of two book
Drawer of size 314(W) X 400(D) X 80(H) and one File Drawer of size 314(W) X 400(D) X 225(H) made
up of 12mm thick Prelaminated Particle board with bottom panel of 9mm thickness. The small drawers
are mounted on Telescopic slide with 3/4 extension. where Big Drawer mounted on Telescopic slide with
full extension allowing storage of files with the help of file manager. Drawer facia made up of 18mm thick
prelaminated particle board. Provision of centralize for all three drawers and a separate lock with tower
bolt for two shutters .Flush type pull handles are fitted on Drawer facia and Shutters.
iv)Levellers – Each frame is provided with two Nos. 12mm long leveling bolts which allow 10-25mm
adjustment for floor unevenness if any.
v)All works mentioned/described above required to be completed in all respect as per drawings &
instruction of Engineer-in-Charge.
7 CUBICAL TABLE - LOW HEIGHT CABIN TABLE (1500L x 1650D x 750H mm)
Manufacture, supply and Installation in position 'L' shape unit as directed Modular workstation , work
surface, Gable end, leteral filing storage units, and with all accessories etc.Nos 4 28,000.00 1,12,000.00
TABLE SIZES
a) (1500 (L) x 750 (D) x 750mm (H)
i) Work Top
1)
Table Top :- 30mm thick Table top made up of 18mm thick Pre-laminated Particle board with 12mm
thick thin PVC foil wrapped decorative profile made up of MDF fixed along all the edges from bottom
side which provide decorative waterfall edge profile to top with twin color look the decorative trim to be
connected at the angle ofrt 45Degree with each other.M.S. T-Hat of 0.8mm thickness is provided for
extra support for the Top of length 1200mm and above.
2)LEG :- 25mm thick Leg or Gable End made up of 25mm thick Pre-laminated Particle board with M.S.
Leveler bracket to give floating look.
3)Work top shall have 2mm PVC edging of approved make quality shade and colour on exposed area and
1mm on covered area.
4)
The top shall be supported with suitable M.S. bracket of standard size made of CRCA sheet of minimum
2mm thick Grade D as per IS 513 with power coated finish of approved colour. Suitable size of metal
insert to be provided in worktop for fixing with the partition/gable end. Fixing directly with screws is not
permissible.
5)
Modesty :- Modesty Panel made up of 18mm thick Pre-laminated Particle board providing stability leg
privacy to user. "D" headed to structure and allow sufficient Decorative aluminum profile fixed on it , the
aluminum profile to be fixed by making grove in panel for better fixing and integrated look.
i)Levellers – Each frame is provided with two Nos. 12mm long leveling bolts which allow 10-25mm
adjustment for floor unevenness if any.
ii)All works mentioned/described above required to be completed in all respect as per drawings &
instruction of Engineer-in-Charge.
iii) Lateral Filing Storage (Return)
Sl.
No.Descriptions Unit Qnty. Rate Amount
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE TECHNOLOGY
PARK OF INDIA AT SALTLAKE, KOLKATA.
(III) BOQ & ESTIMATE MODULAR FURNITURE WORKS
One lateral filing bin of size 900(L)x450(D)x675(H)mm. - 1Nos. Office Table Height Combo storage with
three drawers and One shutter with good storage capacity usable as return storage for office storage.
Top :-28mm thick top made up of 18mm thick Pre-laminated Particle board with 8mm thick thin PVC foil
wrapped decorative profile made up of MDF fixed along all the edges from bottom side which provide
decorative waterfall edge profile to top with twin color look the decorative trim to be connected at the
angle of 45Degree with each other. Carcass :- Side Panel, Verticals, Bottom, Skirting Panel, Shelf and
Shutters are made up of 18mm thick Pre-laminated Particle board with proper grooving done near to
back side edge of side panel and Bottom for fitment of back panel made up of 9mm thick prelaminated
particle board. There is provision for a pedestal structure (i.e. Two Book drawer and one file drawer) and
One Openable storage place with adjustable shelf within.
Drawer :- Provision of two book Drawer of size 314(W) X 400(D) X 80(H) and one File Drawer of size
314(W) X 400(D) X 225(H) made up of 12mm thick Prelaminated Particle board with bottom panel of
9mm thickness. The small drawers are mounted on Telescopic slide with 3/4 extension. where Big
Drawer mounted on Telescopic slide with full extension allowing storage of files with the help of file
manager. Drawer facia made up of 18mm thick prelaminated particle board. Provision of centralize for
all three drawers and a separate lock with tower bolt for two shutters .Flush type pull handles are fitted
on Drawer facia and Shutters.
iv)Levellers – Each frame is provided with two Nos. 12mm long leveling bolts which allow 10-25mm
adjustment for floor unevenness if any.
v)All works mentioned/described above required to be completed in all respect as per drawings &
instruction of Engineer-in-Charge.
8 CONFERENCE TABLE (6000L x 1800D x 750H mm)
Manufacture, supply and Installation in position 'Rectangular' shape unit as directed Modular Conference
Table, work surface, gable end, Modesty Panel and with all accessories etc.Nos 1 1,48,000.00 1,48,000.00
TABLE SIZES
a) (6000 (L) x 1800 (W) x 750mm (H)
i) Work Top
1)
Table Top :- 72mm thick Top surface of conference table as the combination of different types of Top
such as Stationary Main Top with provision for Power Dock fixing, Openable Top with provision of Power
Dock placement and Stationary Side top Side Top and Main Top are made up of 18mm PVC foiled MDF
with three batten of same thickness hied arround the edges from bottom side PVC foiling of top is after
fitment of one batten to it and rest two battens are foiled together which gives a look of two solid blocks
of 36mm thickness Kilned together to form a muscular look of 72mm thickness. Side Top are of
Vermont color and Main Top are Maned in matt black color . Central Tops with openable fiture are made
up of 18mm thick pvc foiled MDF act as horizontal box cover to access the wire mangement provision
with piano hinges. Side Top of 600mm width and length as per final size in case of Mal size is more than
2400mm the table top to be splitted in two equal part. Main Top of 600mm X 600mm size and Openable
top of 596mm width and length according to sizes .
2)
Table top is supported on gable ends made of 200mm thick box patern hollow leg made up of 18mm
thick pvc foiled MDF with C shape part made by foil and fold process Is packed with cover panic made
up of 18mm thick Pre laminated Particle board
3)
Modesty:- Made up of Prelaminated 18mm MDF. Provision of support panel below top for easy wire
management across the Conference table length. Provision of wooden stiffners of 100mm width and
18mm thickness made up of PPS fixed below table top inline with Modesty panel
4) The top shall be supported with suitable M.S. bracket of standard size made of CRCA sheet of minimum
2mm thick Grade D as per IS 513 with power coated finish of approved colour. Suitable size of metal
insert to be provided in worktop for fixing with the partition/gable end. Fixing directly with screws is not
permissible.
5) Gable end Bracket will be of minmum 2.0mm thick CRCA steel Grade D as per IS 513 with metal insert.
6) Wire Management :- Provision for wire pasing throughout the structure without mixing data and power
connections. the wires can be pull inside the tabel from floor and placed in the boxes build below
openable shutter. The access point for data and power can be mount on Main top as well as openable
top.
ii)Levellers – Each frame is provided with two Nos. 12mm long leveling bolts which allow 10-25mm
adjustment for floor unevenness if any.
iii)All works mentioned/described above required to be completed in all respect as per drawings &
instruction of Engineer-in-Charge.
9 Open Metal Book Case Without Door 900Lx450Dx2100mmHt. Nos. 0 32,000.00 0.00
Open Book Case Cabinet of size 900(W) X 450(D) X 2100(H) made up of 0.75mm thick CRCA duly
Epoxy powder coated followed by seven tank process of powder coating. Provision of Six compartment.
Open to all side.Suitable for lateral suspension with centalize system & optional lveler for uneven flooring
surface.
10 Medium Height Storage with 450D and 1200mmHt.
STORAGE SIZES
a) (750 (L) x 450 (D) x 1200mm (H) Nos. 10 11,000.00 1,10,000.00
Sl.
No.Descriptions Unit Qnty. Rate Amount
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE TECHNOLOGY
PARK OF INDIA AT SALTLAKE, KOLKATA.
(III) BOQ & ESTIMATE MODULAR FURNITURE WORKS
i)
Metal storages made up of CRCA Of 0.8 mm thickness. Metal storage of duly powser coated with
proper arrange ment for locking system and PVC Flush type handle. Metal storage shall have 2 shelves
making three compartment. Metal storage shall have PVc levellors required for levelling of storages.
including all required hardwarers including locks etc of approved brand and manufacture complete in all
respect as per direction of Engineer - in Charge/Architect.
11 FREE STANDING LOW HEIGHT PARTITION FOR CUBICAL TABLE AND PASSAGE SQMT 80 8,600.00 6,88,000.00
i) Tile based Partitions
Vertical partition members made of aluminium extrusion alloy of minimum 50x50mm size having
thickness of min 1.2mm for vertical members and that of 1.00mm thick for horizontal members duly
finished with powder coating in desired shade/colour. Both the faces of vertical partition to be fiished with
laminate/fabric panels. Top caps of partition shall be slightly curved/flat shape of aluminium alloy duly
finished with powder coating in desired shade/colour. The partition should have the raceways for carrying
voice and data wire and power cable, which sholuld be separate from each other in the panel. The panel
above the work surface should be on tackable board with fabric panels have fire rating as per NFPA 701
or equivalent fire code. Fabric to be used shall be min. of grade 3. The height of partition shall be of min.
1200mm. All partition should have the provision of level adjuster to adjust the height of + 10mm. All
metal components will be finished with powder coated in desired shalde/colour.100-150mm high metal
skirting
a)1200mm min. high partition with laminate finish below the worktop, fabric above work top towards
Outside of Workstation along corridor / Pasaage
b)1200mm min. high partition with laminate finish below the worktop,1Nos.White Marker writing board and
1Nos. Soft Pinup board above worktop inside of user Per workstation.
c)1200mm min. high partition with laminate finish below the worktop, fabric above work top towards Inside
and Outside of Workstation in return partition / handshake Only end to end of workstation.
TOTAL 31,71,600.00
S.No DESCRIPTION Qty Price Amount
1 Chair for all Staff & conference & meeting Room
1.aSetter 02 : Low Back Chair Ring PU Arms, Seat & Back with PVC Lipping, Centre Tilting
Mechanism, PP Stand & Gas Lift
40 4,500.00 1,80,000.00
Chair for Director at Conference Room
1.b
Main Chair
Leo 02 ‐ High Back Revolving Chair
PU foam in Seat & Back , PP Arms & cushion on it. Central tilting
Mech., PP base duly coated, & Gas Lift
1 15,000.00 15,000.00
2 Officers Cabin
2.a
Main Chair
Leo 02 ‐ Medium Back Revolving Chair
PU foam in Seat & Back , PP Arms & cushion on it. Central tilting
Mech., PP base duly coated, & Gas Lift
5 8,000.00 40,000.00
Visitor Chair for all Officer Cabin
2.b
Spirit 02 :Medium Back Revolving Chair With moulded ply of 12mm thk in seat & 12mm+6mm double ply in
back PU moulded foam in seat, "D" Shape PP Arms, Nylon base,
Synchro Mech., & Gas Lift
10 4,200.00 42,000.00
3 Director's Cabin
3.a
Main Chair
Leo 02 ‐ High Back Revolving Chair
PU foam in Seat & Back , PP Arms & cushion on it. Central tilting
Mech., PP base duly coated, & Gas Lift
1 15,000.00 15,000.00
Visitor Chair for Director's Cabin
3.b
Spirit 02 :Medium Back Revolving Chair With moulded ply of 12mm thk in seat & 12mm+6mm double ply in
back PU moulded foam in seat, "D" Shape PP Arms, Nylon base,
Synchro Mech., & Gas Lift
4 5,000.00 20,000.00
3.c
Sofa for director chamber
Comforty : Sofa Teakwood Frame, with Cushion in Seat & Back,
with arms, Wooden Frame at the base duly polished
Three Seater Sofa ‐ 1930mmW x 750mmD x 750mmH
1 30,000.00 30,000.00
3.d
Sofa Comforty : Sofa
Teakwood Frame, with Cushion in Seat & Back, with arms,
Wooden Frame at the base duly polished Three Seater
Sofa ‐ 1930mmW x 750mmD x 750mmH
2 15,000.00 30,000.00
3.e
Sofa for director chamber
Comforty : Sofa Teakwood Frame, with Cushion in Seat & Back,
with arms, Wooden Frame at the base duly polished Two
Seater Sofa ‐ 1350mmW x 750mmD x 750mmH
1 12,000.00 12,000.00
3.f
Sofa Comforty : Sofa
Teakwood Frame, with Cushion in Seat & Back, with arms,
Wooden Frame at the base duly polished Two Seater
Sofa ‐ 1350mmW x 750mmD x 750mmH
1 12,000.00 12,000.00
4 Work Station Chair for all Staff & visitors
4.aSetter 02 : Low Back Chair Ring PU Arms, Seat & Back with PVC Lipping, Centre Tilting
Mechanism, PP Stand & Gas Lift
52 4,500.00 2,34,000.00
6,30,000.00
78,750.00
7,08,750.00
TOTAL
(IV) BOQ & ESTIMATE CHAIRS
TAX @ 12.5 %
G. TOTAL
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE
SOFTWARE TECHNOLOGY PARK OF INDIA AT SALTLAKE, KOLKATA.
A. POINT WIRING Rs. 850900.00
B. CONDUITING FOR TELEPHONE, COMPUTER &
CONDUITING AND WIRING FOR T.V. SYSTEM.
Rs. 72000.00
C. EARTHING SYSTEM Rs. 198480.00
D. SUPPLY & FIXING OF LIGHTING FIXTURES Rs. 831500.00
E. CABLES, MAINS & SUB MAINS Rs. 280130.00
F DISTRIBUTION BOARDS Rs. 204100.00
G SUB DISTRIBUTION PANELS Rs. 2500.00
H CCTV SYSTEM Rs. 154250.00
I FIRE DETECTION SYSTEM (CONVENTIONAL) Rs. 242100.00
TOTAL Rs. 2835960.00
Unit Qty. Rate In Rs. Amount In Rs.
A. POINT WIRING
Note
Point wiring rates are inclusive of 2x2.5+1x1.5 sq
mm FRLS PVC insulated stranded copper
conductor wires for circuit from D.B. Sensor/
Switch Boards and 1x1.5 sq mm FRLS PVC
insulated copper conductor insulated earth wire.
All sockets to be checked with a Check Plug
socket tester for live-neutral reverse, no
earth,neutral fault, live earth reverse, neutral
earth reverse.
All circuit & point wiring shall be colour coded &
shall have ferruling on both end for circuit
identification complete as required etc.
1
Wiring for the following light points with 3x1.5
Sq.mm FRLS PVC insulated stranded copper
conductor wires in concealed MS. conduits in
F.ceiling / walls /ceiling as directed including
providing and fixing of 6 amps flush type switches, 5
sided G.I Boxes for housing switches and earthing
complete as required.
a. First point controlled by one no. 6 amp switch. Nos. 80 1000.00 80000.00
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE
TECHNOLOGY PARK OF INDIA AT SALTLAKE, KOLKATA.
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE
TECHNOLOGY PARK OF INDIA AT SALTLAKE, KOLKATA.
(V) BOQ & ESTIMATE FOR ELECTRICAL WORKS (ABSTRACT SHEET)
Sl.No. Description
BOQ : ELECTRICAL
Unit Qty. Rate In Rs. Amount In Rs.
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE
TECHNOLOGY PARK OF INDIA AT SALTLAKE, KOLKATA.
Sl.No. Description
BOQ : ELECTRICAL
2
Same as item No. 1above but LOOP POINT i.e.
wiring of point looped from first point with 3 x 1.5 sq.
mm FRLS PVC insulated copper conductor wire in
concealed/exposed MS. conduit and earthing .
Nos. 150 600.00 90000.00
3
Wiring for the following light points with 2 x2.5 + 1 x
2.5 Sq.mm FRLS PVC insulated stranded copper
conductor wires in concealed M.S conduits in
F.ceiling/walls/ceiling as directed including
providing and fixing of 16 amps flush type switches, 5
sided G.I Boxes for housing switches and earthing
complete as required.
a. First point controlled by one no. 16 amp switch. Nos. 10 1200.00 12000.00
4
Same as item No. 3 above but LOOP POINT i.e.
wiring of point looped from first point with 2 x 2.5
+1x2.5 sq.mm FRLS.PVC insulated copper
conductor wire in concealed/exposed M.S conduits
and earthing Nos. 50 700.00 35000.00
5
Wiring for the following light points controlled by MCB
in DB (Cost of MCB has been taken elsewhere in the
tender) with 2 x 2.5 + 2.5 sq. mm FRLS PVC
insulated copper conductor wires in
concealed/exposed M.S. conduits as called for and
earthing. (For Emergency)
a. First point controlled by existing MCB in D.B. Nos. 5 1400.00 7000.00
6
Same as item No. 4 above but LOOP POINT i.e.
wiring of point looped from first point with 2 x 2.5
+1x2.5 sq. mm FRLS. insulated copper conductor
wire in concealed/exposed M.S. conduit and
earthing
Nos. 35 800.00 28000.00
7
Wiring of Emergency light point wire 2 x 2.5
+1x1.5 sq. mm FRLS PVC insulated copper
conductor wire in concealed/exposed 25 mm dia
M.S. conduit
RM 350 150.00 52500.00
8
Wiring for 6 amps light plug outlets with 3x1.5
sq.mm FRLS PVC insulated stranded copper
conductor wires in M.S. Conduits in
ceiling/walls/floor as directed including providing
and fixing of 6 amps flush type 5 pin socket and 6
amps switch with cover plate, 5 sided G.I boxes for
housing switches, sockets and earthing complete as
required. (for general areas)
Nos. 20 1050.00 21000.00
Unit Qty. Rate In Rs. Amount In Rs.
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE
TECHNOLOGY PARK OF INDIA AT SALTLAKE, KOLKATA.
Sl.No. Description
BOQ : ELECTRICAL
9
Wiring for inline fan points with 2 x 2.5+1x1.5
sq.mm FRLS PVC insulated stranded copper
conductor wires in concealed M.S. conduits in
F.ceiling/ walls/ Ceiling as directed including
providing and fixing of 16 amps flush type switches
16 amps 3 pin socket near inline fan, 5 sided G.I.
boxes for housing switches and 16 amps 3 pin socket
outlet and earthing and complete as
required.(including body earth for GI boxes)
Nos. 2 1300.00 2600.00
10
Wiring for Ceiling fan points with 3x1.5 Sq.mm
FRLS PVC insulated copper conductor wires in
concealed FRLS PVC conduits in ceiling / walls as
directed including providing and fixing of Hexagonal
fan Box, and electronic fan requlator 6 A switch, 5
sided G.I. Boxes for housing the regulator, switch and
earthing complete as required.
Nos. 0 1100.00 0.00
11
Wiring for projector points with 2 x 4 + 1 x 2.5 sq
mm FRLS PVC insulated stranded copper
conductor wires in concealed M.S. conduits in
F.ceiling/ walls/ Ceiling as directed including
providing and fixing of 16 amps flush type switch
near the white board and 16 amps 5 pin socket near
the projector in ceiling , 5 sided G.I. boxes for
housing switches and 16 amps 3 pin socket outlet
and earthing and complete as required.(including
body earth for GI boxes) ( 1 point per circuits)
Nos. 1 2200.00 2200.00
12
Wiring for VRV/VAV points with 3 x 2.5 sq.mm
FRLS PVC insulated stranded copper conductor
wires in concealed M.S. conduits in F.ceiling/ walls/
Ceiling as directed including providing and fixing of 6
amps flush type switches 6 amps 3 pin socket near
VAV points, 5 sided G.I. boxes for housing switches
and 16 amps 3 pin socket outlet and earthing and
complete as required.(including body earth for GI
boxes) ( 3 to 4 points per circuits)
Nos. 0 1250.00 0.00
13
Wiring for 16 amps power outlet points with
2x4+1x2.5 sq.mm FRLS PVC insulated stranded
copper conductor wires in concealed/recessed M.S.
conduit as directed including providing and fixing of
16 amps flush type switch and 6 pin socket with
cover plate 5 sided G.I. outlet boxes for switches and
socket and earthing the third pin with 1x2.5 sq mm
FRLS PVC stranded copper wire complete as
required (Only one outlet shall be connected on each
circuit) (including body earth for GI boxes)
Nos. 20 2200.00 44000.00
Unit Qty. Rate In Rs. Amount In Rs.
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE
TECHNOLOGY PARK OF INDIA AT SALTLAKE, KOLKATA.
Sl.No. Description
BOQ : ELECTRICAL
14
Wiring for 16 amps power outlet points with
2x4+1x2.5 sq.mm FRLS PVC insulated stranded
copper conductor wires for the first power outlet and
2x4+1x2.5 sq.mm FRLS PVC insulated stranded
copper conductor wires for the second outlet, in
concealed M.S. conduits in F.ceiling/
walls/Ceiling/floor ducts as directed including
providing 16 amps flush type switch and 6 pin socket
with cover plate, 5 sided G.I. outlet boxes for housing
switches and socket, and earthing the third pin with
1x2.5 sq.mm FRLS PVC insulated copper conductor
wires complete as required (Two power outlets shall
be connected on each circuit)(including body earth
for GI boxes)
Set of
Two6 3200.00 19200.00
15
Wiring for A/C outlet points with 4.0 sq mm FRLS
PVC insulated stranded copper conductor wires in
M.S. conduitl/wall/floor ducts as directed including
providing and fixing of 25 A socket with 25 amps SP
MCB ( Tiny Trip) 5 sided GI Outlet Box for housing
and socket and MCB and earthing with 2.5 sq. mm
FRLS PVC insulated stranded Copper Conductor
wires complete as required.
Nos. 5 3000.00 15000.00
16
Wiring for UPS/Raw plug outlets points with three
core, 2.5 sqmm FRLS PVC Insulated and PVC
sheathed flexible cable with bright annealed
electrolytic copper conductor , 1100 volt grade
confirming to IS : 694/1990 with latest amendments,
in existing Channels/ conduit in ceiling/walls/floor
including all cable termination accessories)
(including body earth for GI boxes)
RM 1500 96.00 144000.00
17
Wiring for UPS plug outlets points with three core,
4.0 sqmm FRLS PVC Insulated and PVC sheathed
flexible cable with bright annealed electrolytic copper
conductor , 1100 volt grade confirming to IS :
694/1990 with latest amendments, in existing
Channels/ conduit in ceiling/walls/floor including all
cable termination accessories) Earthing of GI Box to
be included
RM 400 145.00 58000.00
18
Wiring for UPS plug outlets points with three core,
6.0 sqmm FRLS PVC Insulated and PVC sheathed
flexible cable with bright annealed electrolytic copper
conductor , 1100 volt grade confirming to IS :
694/1990 with latest amendments, in existing
Channels/ conduit in ceiling/walls/floor including all
cable termination accessories)
RM 60 185.00 11100.00
The word UPS shall be engraved on all UPS
sockets
The word RAW shall be engraved on all RAW
sockets
The Circuit No. and DB no. label shall be provided
on all UPS ,RAW sockets and switchboards with
label printer.
Unit Qty. Rate In Rs. Amount In Rs.
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE
TECHNOLOGY PARK OF INDIA AT SALTLAKE, KOLKATA.
Sl.No. Description
BOQ : ELECTRICAL
19
Providing and fixing of 1 Nos.6/13 amp flush type 3
pin international socket and 1 No. 16 amps switch
cover plate, 5 sided G.I. Boxes for housing switches
and sockets and earthing complete as required (for
UPS). GI Box to have earth pin for body earthing
Nos. 15 400.00 6000.00
20
Providing and fixing of 2 Nos.6/13 amp flush type 3
pin international socket and 1 No. 16 amps switch
cover plate, 5 sided G.I. Boxes for housing switches
and sockets and earthing complete as required (for
UPS). GI Box to have earth pin for body earthing
Nos. 70 550.00 38500.00
21
Providing and fixing of 3 Nos.6/13 amp flush type 3
pin international socket and 1 No. 16 amps switch
cover plate, 5 sided G.I. Boxes for housing switches
and sockets and earthing complete as required (for
UPS). GI Box to have earth pin for body earthing
Nos. 0 650.00 0.00
22
Providing and fixing of 1 No.6/13 amp flush type 3 pin
international socket and 1 No. 16 amps switch cover
plate, 5 sided G.I. Boxes for housing switches and
sockets and earthing complete as required ( for Raw)
GI Boxes to have earth pin for body earthing
Nos. 70 400.00 28000.00
23
Providing and fixing of 1 No.16 amps flush type 6 pin
socket and 1 No. 16 amps switch with indicator,
cover plate, 5 sided G.I. Boxes for housing switches
and sockets and earthing complete as required (for
UPS) GI Boxes to have earth pin for body earthing
Nos. 15 450.00 6750.00
24
Providing and fixing of 16 amp flush type 6 pin socket
and 16 amp switch, cover plate, 5 sided G.I. Boxes
for housing switches and sockets and earthing
complete as required GI Boxes to have earth pin for
body earthing
Nos. 10 400.00 4000.00
25
Providing and fixing Underfloor Access Outlets (250
x 250 x 60 - mm 75 compartments 1Trap including
providing 2 Nos 6 Amps international sockets and 2
nos 6 Amps switch and space for 4 Nos. RJ-45
data/ voice outlet complete as required.
Nos. 0 8500.00 0.00
26
Providing and fixing in position Legrand Make pop-up
boxes 5+2 modules including 2 nos. 6/13 Amp socket
with 1 No. 16 Amp switch and 2 nos cat 6 RJ45
data/voice outlet. (For Confernce Room)
Nos. 8 4500.00 36000.00
27
Supply and fixing of the following sizes of
thermoplastic moulded plug and socket in PVC Box
of suitable size flush / surface and making
connections complete as required. The box shall be
IP 44.
Unit Qty. Rate In Rs. Amount In Rs.
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE
TECHNOLOGY PARK OF INDIA AT SALTLAKE, KOLKATA.
Sl.No. Description
BOQ : ELECTRICAL
a3 pin 16/20 A 1 phase industrial socket with plug top
Nos. 0 1500.00 0.00
b3 pin 25/32 A 1 phase industrial socket with plug top
Nos. 6 1800.00 10800.00
c3 pin 20 A 1 phase industrial socket with
interlocking switch and plug topNos. 0 2500.00 0.00
28
Supply and fixing of the following sizes of G.I /PVC
Box along with switch and cover plate complete with
all fixing accessories as required. For Emergency
light
a 1-3 Module G.I. box with 1 no. 6 Amps switch and
cover plateNos. 0 93.00 0.00
b.1-3 Module G.I. box with 2 nos. 6 Amps switch and
cover plateNos. 0 125.00 0.00
c.1-3 Module G.I. box with 4 nos. 6 Amps switch and
cover plateNos. 0 196.00 0.00
29
Providing and fixing in position the following M.S.
conduits including all accessories concealed in F.
ceiling/wall/floor as required including 1.6 mm thick
M.S. junction or pull boxes with 3mm thick perspex
sheet cover plate complte with 1.6 mm dia. G.I. pull
wires in the length of conduit.
a. 20 mm dia conduit ( 1.6 mm thick) RM 50 100.00 5000.00
b. 25 mm dia conduit (1.6 mm thick) RM 450 115.00 51750.00
c. 32 mm dia conduit (2.0 mm thick) RM 150 180.00 27000.00
30
The Electrical Contractor shall provide sufficient
temporary lighting for working in the Building total
area 8000 sq. ft (approx) divided in one floor and
maintain the same till completion of the project.It
shall include replacement of all fused/faulty lamps.It
shall include providing 15 A plug sockets (industrial
type with ON/OFF switch/MCB) on 4 sides walls one
plug at every 3 meter distance. The Contractors will
tap off supply from these plugs for his use.
Halogen/tubelights to maintain a lighting level of 150
lux on the floor,.Each 15 A socket and each Light
circuit shall be protected by suitable MCBs.Use three
core PVC Insulated PVC sheathed copper conductor
cables for wiring.The contractor shall salvage the
complete wiring and take it back at the end of the
project.
L.S. 1 15500.00 15500.00
TOTAL CARRIED OVER TO SUMMARY 850900.00
B. CONDUITING FOR TELEPHONE , COMPUTER &
CONDUITING AND WIRING FOR T.V. SYSTEM.
Unit Qty. Rate In Rs. Amount In Rs.
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE
TECHNOLOGY PARK OF INDIA AT SALTLAKE, KOLKATA.
Sl.No. Description
BOQ : ELECTRICAL
1
Providing and fixing in position the following FRLS
PVC conduits including all accessories concealed in
F. ceiling (PVC conduit not to be installed above false
ceiling)/wall/ floor as required including M.S. junction
or pull boxes with 3mm thick perspex sheet cover
plate complete with 1.6 mm dia G.I. pull wires in the
length of conduit.
a. 20 mm dia conduit RM 0 45.00 0.00
b. 25 mm dia conduit RM 0 55.00 0.00
c. 32 mm dia conduit RM 0 70.00 0.00
2
Providing and fixing in position the following M.S.
conduits including all accessories concealed in F.
ceiling/wall/floor as required including 1.6mm thick
M.S. junction or pull boxes with 3mm thick perspex
sheet cover plate complete with 1.6 mm dia G.I. pull
wires in the length of conduit.
a. 20 mm dia conduit ( 1.6 mm wall thickness) RM 0 105.00 0.00
b. 25 mm dia conduit ( 1.6 mm wall thickness) RM 350 135.00 47250.00
c. 32 mm dia conduit (2 mm wall thickness) RM 50 180.00 9000.00
3Providing and fixing in position suitable 1.2 mm
thick G.I./ PVC outlet box for RJ- 45 computer/Voice
outlet with all fixing accessories as required.
Nos. 130 75.00 9750.00
4
Supply and Laying including numbering / ferruling of
wire (8 digit) and the continuity test for each cable
of Cat 6 - Telephone / Data cable in existing G. I.
Channel.
RM 0 40.00 0.00
5Supply and fixing of 1.2 mm thick G.I Box along with
RG 11 TV Co axial socket with Cover PlateNos. 2 300.00 600.00
6
Supply drawing connecting testing and
commissioning of TV Coaxial cable RG 6 in existing
conduit
RM 150 36.00 5400.00
TOTAL CARRIED OVER TO SUMMARY 72000.00
C. EARTHING SYSTEM
1Providing and fixing in position the following copper
strips and wires including providing all fixing
accessories and effecting proper connections
a. G.I. tape 25 mm x 6 mm RM 20 150.00 3000.00
b. Copper tape 25mm x 3 mm RM 15 450.00 6750.00
c. Copper wire 8 SWG RM 350 85.00 29750.00
d. Copper wire 12 SWG RM 100 55.00 5500.00
Unit Qty. Rate In Rs. Amount In Rs.
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE
TECHNOLOGY PARK OF INDIA AT SALTLAKE, KOLKATA.
Sl.No. Description
BOQ : ELECTRICAL
2
Supply & laying, effecting proper connections,
testing & commissioning of the following sizes of 1.1
KV PVC insulated PVC sheathed copper conductor
cables conforming to IS : 694/1990 with latest
amendments laid over MS supports in existing RCC
ducts/ laid in ground /laid on Cable Trays including
clamping the cables to supports in an approved
manner as required complete with all accessories.
a 1c x 35 sq.mm PVC insulated PVC flexible copper
conductor cables (For UPS SDB Earthing )
RM 40 350.00 14000.00
b 1c x 25 sq.mm PVC insulated PVC flexible copper
conductor cables (For Server & UPS SDB Earthing )
RM 150 250.00 37500.00
c
1 x 10 Sq. mm PVC insulated PVC flexible copper
conductor cables (Green Colour for UPS DB Sub-
main Earthing)
RM 50 120.00 6000.00
d1 Nos 10 sqmm PVC insulated copper conductor
wireRM 0 80.00 0.00
e1 x 6 Sq. mm PVC insulated PVC flexible copper
conductor cables (Green Colour) RM 200 50.00 10000.00
3
Supplying and making terminal joints for the following
size of 1.1 KV PVC insulated copper conductor
armoured cables including providing heavy duty
copper terminal crimping lugs, solder, insulation tape,
approved sealing epoxy compound, brass cable
glands, effecting gland connections and effecting
terminal connections to the equipment complete as
required.
a1c x 35 sq.mm PVC insulated PVC flexible copper
conductor cable jointsJt 4 250.00 1000.00
b1c x25 sq.mm PVC insulated PVC flexible copper
conductor cable jointsJt 6 200.00 1200.00
c
1 x 10 Sq. mm PVC insulated PVC flexible copper
conductor cables (Green Colour for UPS DB Sub-
main Earthing)
Jt 4 125.00 500.00
4
Providing earthing station at location as called for
including providing 600 mm x 600 mm x 6.0 mm
thick tinned copper electrode including porviding 2
Nos 25 x 6 mm GI strip up to ground level 20mm dia
medium class GI pipe (India Tube Company make or
approved equal) CI funnel with 20 gauge GI wire
mesh, masonry chamber with concrete base, CI
manhole cover with frame (300mm x 300mm) and
bitumastic paint and packing the fixture of charcoal
and common salt around plate electrode complete as
per I.S. ( Minimum depth shall be 4.2 M ) ( for
Neutral earthing, TF&DG)
Nos. 0 14500.00 0.00
Unit Qty. Rate In Rs. Amount In Rs.
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE
TECHNOLOGY PARK OF INDIA AT SALTLAKE, KOLKATA.
Sl.No. Description
BOQ : ELECTRICAL
5
Supply, Installation, testing and commissioning of
Maintenance Free Earthing of make Electrolytic
Earthing comprising of type 'K' copper 2.4 mm wall
thickness, hollow tube 10 feet long, 2.125 inches
outer diameter completely filled with non hazardous
metallic salts to achieve an earth resistance of less
than 1 ohms. Provide masonry chamber with
concrete base, CI manhole cover (cover to be heavy
duty) with frame (300mm x 300mm) for UPS &
Server
Nos. 3 25000.00 75000.00
6
Supply, installation, testing and commissioning of
sheet metal enclosed 350 x 200 x 150 ( D) mm
insulated earth distribution board with 1 nos. 50 x 6
mm copper tinned earth bars on SMC insulator
suitable for 6/8 nos connections complete with all
fixing accessories as required.
Nos. 2 3000.00 6000.00
7
Supplying and laying of the following sizes of Heavy
duty PVC Pipes below paved area including chase
cutting and back filling.
a. 100 mm dia RM 0 164.00 0.00
b. 80 mm dia RM 20 114.00 2280.00
TOTAL CARRIED OVER TO SUMMARY 198480.00
D. SUPPLY & FIXING OF LIGHTING FIXTURES
1
Supplying ,fixing in position testing and
commissioning of the following Lighting fixtures
including lamps at site. Use all Philips
Trulite/Osram lumilux plus Eco lamps in Fluorescent
lamp fittings.(4000 K) Use Osram CFL lamp - Dulux
L Lumilux in all CFL lamp fixtures (4000 K) (Samples
of all light fixtures to be submitted to the client for
approval prior to procurement of fixtures)
All Bulbsn /any other consumables should be
branded.It should have atleast one year replacement
guarantee.
NoteAll Light Fixture shall be with H.F. electronic
ballast ( THD less than 10% and P.F. 0.995 )
a. 1 x 28 watts T-5 lamp Slim patti light fixture Philips
Cat No. TMS 122/128E HF for cove lightNos 180 800.00 144000.00
b.
1 x14 watts T- 5 lamp cove light as per Philips Cat.
No. TCH 204 - 1 x 14 or Equivalent make for cove
light
Nos 30 650.00 19500.00
c.14 Watts Green LED Light fixture as per Philips Cat
No-BBS1701XDLED or Equivalent makeNos 175 1500.00 262500.00
d.40 watts LED Light fixture as per Wipro Cat No
RC170B or Equivalent makeNos 85 3500.00 297500.00
Unit Qty. Rate In Rs. Amount In Rs.
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE
TECHNOLOGY PARK OF INDIA AT SALTLAKE, KOLKATA.
Sl.No. Description
BOQ : ELECTRICAL
e.4 x 14 watts T5 Light fixture as per Philips Cat No
TBS 869 or Equivalent makeNos 0 4000.00 0.00
f.
2 x 36 watts CFL Light fixture as per Wipro Cat No
WVP 44236 SGW (working Area) or Equivalent
make
Nos 0 3500.00 0.00
g.1 x 20 watts Patti Light fixture as per Wipro Cat No
WDF 9120 or Equivalent makeNos 20 650.00 13000.00
h.Channel light fixture as per architect /Client basic
cost - Rs 5000 (For Conference Room)Nos 0 6000.00 0.00
i.
2 x 18 watts CFL Lamp Light fixture as per Philips
Cat No FBH145 with glass cover (Working Area)or
Equivalent make
Nos 0 1650.00 0.00
j. 1 x 18 watts CFL Lamp Light fixture as per Wipro
Cat No. 36118 with glass cover or Equivalent make
Nos 0 1550.00 0.00
k. 2 x 18 watts CFL Lamp Light fixture as per Wipro
Cat .WVP 17218 with reflector or Equivalent make
Nos 0 2200.00 0.00
l
3 Watts LED Ni Cd Battery backup up to 2 hrs
emergency Exit light Bajaj Make BESL 03 LED
SSD/ DSD WBB Green
Nos 10 5000.00 50000.00
2
SITC 48" dia (1200 sweep) double ball bearing
ceiling fan with all fixing acessories.
Crompton/Usha/ Havels Nos 0 1650.00 0.00
3
SITC 400 mm dia wall fan with three speed push
button control, 90 degree oscillation, vertical
adjustability, with all fixing
acessories.Crompton/Usha/ Havels Nos 20 2250.00 45000.00
TOTAL CARRIED OVER TO SUMMARY 831500.00
E. CABLES ,MAINS & SUBMAINS
1
Supply and laying, effecting proper connections,
testing & commissioning of the following sizes of 1.1
KV XLPE armoured/ unarmoured PVC insulated
PVC sheathed aluminium /copper conductor cables
conforming to IS : 7098 and IS 1554 Part I and IS
694 for Flaxible copper cable with latest
amendments laid over MS supports in existing RCC
ducts/ laid in ground /laid on Cable Trays including
clamping the cables to supports in an approved
manner as required complete with all accessories.
Note : All cables to be glanded and crimped with
suitable sized lugs. All Cable trays to be double
earthed. All raceways and cable glands to be
earthed with brass round earth clips and wires.
Unit Qty. Rate In Rs. Amount In Rs.
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE
TECHNOLOGY PARK OF INDIA AT SALTLAKE, KOLKATA.
Sl.No. Description
BOQ : ELECTRICAL
a.3.5 c x 150 sq.mm XLPE armourd aluminium
conductor cable RM 0 1115.00 0.00
b.3.5 c x 70 sq.mm XLPE armourd aluminium
conductor cable RM 0 575.00 0.00
c.3.5 c x 50 sq.mm XLPE armourd aluminium
conductor cable RM 0 480.00 0.00
d.4 c x 25 sq.mm XLPE armourd aluminium conductor
cable RM 0 300.00 0.00
e. 4 c x 25 sq.mm armoured copper cable RM 0 1250.00 0.00
f. 4 c x 16 sq.mm armoured copper cable RM 50 1063.00 53150.00
g. 4 c x 16 sq.mm armoured aluminium cable RM 150 230.00 34500.00
h. 4 c x 10 sq.mm armoured copper cable RM 0 500.00 0.00
i. 4 c x 6 sq.mm armoured copper cable RM 0 350.00 0.00
j. 4 c x 4 sq.mm armoured copper cable RM 0 300.00 0.00
k. 3 c x 6 sq.mm XLPE copper cable RM 50 350.00 17500.00
l.2 c x 16 sq.mm PVC insulated armoured copper
conductor cables RM 100 596.00 59600.00
m.2 c x 10 sq.mm PVC insulated armoured copper
conductor cablesRM 0 250.00 0.00
n.1c x 35 sq.mm PVC insulated PVC flexible copper
conductor cables RM 0 350.00 0.00
o.1c x 25 sq.mm PVC insulated PVC flexible copper
conductor cables RM 0 250.00 0.00
p1c x 16 sq.mm PVC insulated PVC flexible copper
conductor cables RM 400 260.00 104000.00
2
Supplying and making terminal joints for the following
size of 1.1 KV PVC insulated copper conductor
armoured cables including providing heavy duty
copper terminal crimping lugs, solder, insulation tape,
approved sealing epoxy compound, double
compression brass cable glands, effecting gland
connections and effecting terminal connections to
the equipment complete as required.
a.3.5 c x 150 sq.mm XLPE armourd aluminium
conductor cable for A/C panel Jt 0 1150.00 0.00
b.3.5 c x 50 sq.mm XLPE armourd aluminium
conductor cable for A/C panel Jt 0 750.00 0.00
c.4 c x 25 sq.mm XLPE armourd aluminium conductor
cableJt 0 700.00 0.00
Unit Qty. Rate In Rs. Amount In Rs.
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE
TECHNOLOGY PARK OF INDIA AT SALTLAKE, KOLKATA.
Sl.No. Description
BOQ : ELECTRICAL
d.4 c x 16 sq.mm armoured copper cable for UPS,
DB'sJt 2 800.00 1600.00
e.4 c x 16 sq.mm armoured AL cable for UPS, Light
and power DB'sJt 6 280.00 1680.00
f. 4 c x 10 sq.mm armoured aluminium cable Jt 0 100.00 0.00
g. 4 c x 10 sq.mm armoured copper cable Jt 0 250.00 0.00
h. 4 c x 6 sq.mm armoured copper cable Jt 0 250.00 0.00
i. 4 c x 4 sq.mm armoured copper cable Jt 0 200.00 0.00
j. 3 c x 6 sq.mm armoured copper cable Jt 6 150.00 900.00
k.2 c x 16 sq.mm PVC insulated armoured copper
conductor cables Jt 6 200.00 1200.00
l.2 c x 10 sq.mm PVC insulated armoured copper
conductor cablesJt 0 200.00 0.00
m.1c x 35 sq.mm PVC insulated PVC flexible copper
conductor cables Jt 0 350.00 0.00
n1c x 25 sq.mm PVC insulated PVC flexible copper
conductor cables Jt 30 200.00 6000.00
o1c x 16 sq.mm PVC insulated PVC flexible copper
conductor cables Jt 0 200.00 0.00
TOTAL CARRIED OVER TO SUMMARY 280130.00
F DISTRIBUTION BOARDS
1
Supply,inginstalling ,connecting testing and
commissioning of the following double door 1/4
rows vertical type 1.6 mm thick main frame and
1.4mm thick door sheet steel enclosed fully recessed
type, TPN Miniature Circuit Breakers Distribution
Boards dust proof, vermin proof, with hinged and
lockable doors complete with DP MCB's and inter-
connection with copper wires, or copper tapes, cable
glands/conduit entry bushes, bonding to earth and
painting. Also provide separate neutral busbar for
each phase. Provide separate Earth Links for each
phase.. Use brass thimbles for connections of all
wires. 1 row for single phase and 4 rows for 3 phase.
Provide separate 4 way 63 A main neutral link also.
1 Light & Power Distribution Board
a
8+2 Way TPN DB, each phase consisting of 8 Nos.
10/20 AMP SP MCB’s and controlled by one number
100 mA sensitivity 63 AMPS DP RCCB backed up
with 1 no 63 Amps 4 pole MCB.
Nos.. 0 18500.00 0.00
Unit Qty. Rate In Rs. Amount In Rs.
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE
TECHNOLOGY PARK OF INDIA AT SALTLAKE, KOLKATA.
Sl.No. Description
BOQ : ELECTRICAL
b
10+2 Way TPN DB, each phase consisting of 10
Nos. 10/20 AMP SP MCB’s and controlled by one
number 100 mA sensitivity 63 AMPS DP RCCB
backed up with 1 no 63 Amps 4 pole MCB.
Nos.. 4 18500.00 74000.00
c
8+2 Way TPN DB, each phase consisting of 8 Nos.
10/20 AMP SP MCB’s and controlled by one number
100 mA sensitivity 63 AMPS DP RCCB backed up
with 1 no 63 Amps 4 pole MCB.
Nos.. 0 16000.00 0.00
d
10+4 Way SPN DB, consisting of 10 Nos. 10/20 AMP
SP MCB’s and controlled by one number 100 mA
sensitivity 40 AMPS DP RCCB backed up with 40
Amps DP MCB.
Nos.. 1 7500.00 7500.00
2UPS Distribution Boards (All MCB's in UPS DB's
should be D Curve)
a
8+2 Way TPN DB, each phase consisting of 8 Nos.
10/20 AMP SP MCB’s and controlled by one number
100 mA sensitivity 63 AMPS DP RCCB Hi ( high
immunity) for each phase and 1 no. 63 amps 4 pole
MCB incomer
Nos.. 0 16500.00 0.00
b
10+2 Way TPN DB, each phase consisting of 10
Nos. 10/20 AMP SP MCB’s and controlled by one
number 100 mA sensitivity 63 AMPS DP RCCB Hi (
high immunity) for each phase and 1 no. 63 amps 4
pole MCB incomer
Nos.. 2 18500.00 37000.00
c
16 Way SPN DB, consisting of 12 Nos. 10/16 AMP
SP MCB’s and controlled by one number 100 mA
sensitivity 63 AMPS DP RCCB (high immunity)
backed up with 63 Amps DP MCB.( Bus Bar should
be twin bus bar)
Nos.. 0 6500.00 0.00
d
8+2 Way SPN DB, consisting of 4 Nos. 20/32 AMP
DP MCB’s and controlled by one number backed up
with 63 Amps DP MCB.( Bus Bar should be twin bus
bar)
Nos.. 2 7500.00 15000.00
3
Supply, installation, testing and commissioning of
sheet metal enclosed 63 A TPN MCB ( 10 KA) for
15 KVA UPS.(This shall include cable entry boxes
both for incoming and outgoing cable)
Nos. 4 3500.00 14000.00
4
Supply, installation, testing and commissioning of 1.6
mm sheet metal weather proof encloser with 63 A
TPN MCCB ( 25 KA) for VRV Outdoor Unit.(This
shall include cable entry boxes both for incominitng
and outgoing cable)
Nos. 4 12500.00 50000.00
5
Supply, installation, testing and commissioning of
1.6 mm thickness sheet metal enclosures fitted with
63 A TPN MCB for AHU
Nos. 0 2850.00 0.00
6
Supply, installation, testing and commissioning of
1.6 mm thickness sheet metal weather proof
polycarbonate enclosures fitted with 16/20 A DP
MCB for A.C.
Nos. 4 1650.00 6600.00
Unit Qty. Rate In Rs. Amount In Rs.
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE
TECHNOLOGY PARK OF INDIA AT SALTLAKE, KOLKATA.
Sl.No. Description
BOQ : ELECTRICAL
6
Supply, installation, testing and commissioning of
1.6 mm thickness sheet metal enclosures fitted with
63 A DP MCB for inverter
Nos. 0 1250.00 0.00
TOTAL CARRIED OVER TO SUMMARY 204100.00
G SUB DISTRIBUTION PANELS
1 Sub Distribution Panels
Design, manufacture, supplying at site installing in
position, connecting, testing and commissioning of
the following cubical type, dead front, 2mm thick
sheet steel enclosed, free standing indoor type
extendible Sub Distribution Panel with vermin proof
hinged lockable doors for each compartment provide
bus bar interconnections for incoming and outgoing
including feeders earthing and painting and as per
specifications.
Note
All MCCB in UPS Distribution Panel Shall be TP +
Neutral 200% of rated currrent with isolation link.
There shall be one hole for each cable
termination in the busbar link for both phase and
neutral.
Provide insulated dedicated earth link in all UPS
Panels
All outgoing feeders should have ON/OFF
indication in all the panels
All MCB's shall be D Curve in all UPS Panel
a. The UPS SDB shall consists of :
INCOMER
Main incomer 2 x 63 A TPN MCCB ( 25 kA) terminal
suitable for cable connection on one side and Busbar
connection on the other side.
BUSBARS
150 amps 4 pole busbar chamber of suitable length
with Copper busbars. All busbars and
interconnections shall be of suitable size copper
strips current density of copper shall not be more
than 1.6 Amps/ sq.mm provide 100% capacity for
neutral bus bar.
INDICATING PANEL
3 nos phase indicating lamps each backed up with
MCB and switch shall be provided for incomer.
Unit Qty. Rate In Rs. Amount In Rs.
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE
TECHNOLOGY PARK OF INDIA AT SALTLAKE, KOLKATA.
Sl.No. Description
BOQ : ELECTRICAL
Provide Transient Voltage Surge Suppressor Rating
40 kA. Including all necessary accessories.
Intelligent Panel Meter (96 mm x 96 mm) covering 25
electrical parameters with RS 485 port for incomming
feeder
OUTGOINGS
5 Nos 63 A TPN MCB (10 kA) terminals suitable to
receive Cable on one side and Busbar connection on
the other side.
4 Nos 63 A DP MCB (10 kA) terminals suitable to
receive Cable on one side and Busbar connection on
the other side.
UPS SDB as described above and specifications
complete.Set 0 72000.00 0.00
b. The SDB Light & Power shall consists of :
INCOMER
Main incomer 1 NO. 200 A TPN MCCB ( 35 kA)
terminal suitable for cu cable connection on one side
and Busbar connection on the other side.
BUSBARS
300 amps TPN busbar chamber of suitable length
with AL busbars. All busbars and interconnections
shall be of suitable size AL strips current density of
AL shall not be more than 0.8 Amps/ sq.mm provide
50% capacity for neutral bus bar.
INDICATING PANEL
3 nos phase indicating lamps each backed up with
MCB and switch shall be provided for incomer.
Intelligent Panel Meter (96 mm x 96 mm) covering 25
electrical parameters with RS 485 port for incomming
feeder
OUTGOINGS
5 Nos. 63 A TPN MCCB (25 kA) with terminals
suitable for cable connection on one side and Bus
bar connection on other side.
10 Nos. 63 A TPN MCB ( 10 kA) with terminals
suitable for cable connection on one side and Bus
bar connection on other side.
Unit Qty. Rate In Rs. Amount In Rs.
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE
TECHNOLOGY PARK OF INDIA AT SALTLAKE, KOLKATA.
Sl.No. Description
BOQ : ELECTRICAL
3 Nos. 63 A DP MCB ( 10 kA) with terminals suitable
for cable connection on one side and Bus bar
connection on other side.
5 Nos. 16/20 A DP MCB ( 10 kA) with terminals
suitable for cable connection on one side and Bus
bar connection on other side.
The SDB Light and Power as described above
and specifications completeSet 0 150000.00 0.00
2
Providing & fixing in position 1000 mm wide ,
Electrical Insulating Mats as per IS 15652:2006, 2mm
thick, suitable upto 3.3 KV , fire retardant,no effect of
acids, alkalies and transformer oils, moisture proof,
high tensile strength and texture finish / cloth
impression (Anti slip , marking on top) . Duratuf make
RM 0 3500.00 0.00
3
Supply & fixing in position approved shock treatment
chart written in English Hindi and Local language.
These charts shall be framed in wooden frame &
covered with clear glass
Nos. 1 1500.00 1500.00
4
Supply & fixing in position the best quality danger
notice boards of approved shape & size as reqd. by
the local Electrical Inspecting Authority written in
English, Hindi & local language.
Nos. 1 1000.00 1000.00
5Supply, installation, testing & commissioning of 1.0
KVA, 1 Phase, Pure Sine Wave inverter with 60
Minute. battery back up (EXIDE BATTERY),
complete with battery Cabinet. As per specification
Set 0 25000.00 0.00
TOTAL CARRIED OVER TO SUMMARY 2500.00
H. CCTV SYSTEM
1 Colour Camera with Varifocal lens 2.8mm to 10 mm
,internal syncronisation, 2 inch HAD ,530 HTV
resolution, 0.5 lux, 3.4" Dome Type.
Nos. 6 9000.00 54000.00
2 Colour Camera Box type with fixed lens 3.6 mm, 2
inch HAD ,530 HTV resolution, 0.5 lux, 3.4" Dome
Type ( Day & Night Camera)
Nos. 0 12500.00 0.00
3
8 Channel Digital Video Surveillance System, record
rate 400 FPS – record and viewing shall be 25 FPS
per Camera, with built in Multiplexer, Video motion
detection, smart search with TCP – IP connectivity,
recording on real time , high quality (24 hours, 90
days), HDD suitable for 24 hours and 90 days
recording, Windows 2007 Professional OS, MPEG 4
plus and other options, Resolution – 640 x 480
pixels, suitable for connecting the CCTV’s.
Nos. 1 45000.00 45000.00
Vendor to submit HDD calculations
4 19" TFT CCTV Colour Monitor Nos. 1 10000.00 10000.00
Unit Qty. Rate In Rs. Amount In Rs.
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE
TECHNOLOGY PARK OF INDIA AT SALTLAKE, KOLKATA.
Sl.No. Description
BOQ : ELECTRICAL
5 SMPS Based Power Supplies 2AMP Each ( for
camera power supply)Nos. 8 1500.00 12000.00
6 Supply and laying of following size M.S. conduit
complete with support brackets/clamps, junction
boxes etc. complete.
a 25 mm Dia M.S Conduit 1.6 mm wall thickness RM. 250 70.00 17500.00
b 32 mm Dia M.S Conduit 2 mm wall thickness RM. 0 100.00 0.00
7 Supply and drawing of the RG 6 co-axial cable for
signalRM 300 40.00 12000.00
8 Supply and drawing of the 3 x 1.5 sq. mm PVC
insulated copper conductor cable for camera power
including cable glands.
RM 150 25.00 3750.00
9 AMC Charges for 2nd year LS 0 0.00 0.00
10 AMC Charges for 3rd year LS 0 0.00 0.00
TOTAL CARRIED OVER TO SUMMARY 154250.00
I. FIRE DETECTION SYSTEM (Conventional)
Note
All A.C Unit and Exit door shall be integrated
with fire panel so that in case of fire signal, all
shall be switched OFF.
2 Layer For Ceiling and Above False Ceiling
1
Supply, installation, connecting, testing and
commissioning of photoelectric type Smoke
Detectors with mounting base, blinking LED etc.
complete as required.
Nos 45 1600.00 72000.00
2
Supply,installation, connecting, testing and
commissioning of rate of rise cum fixed temperature
Heat Detectors with mounting base, blinking LED etc.
complete as required.
Nos 5 1550.00 7750.00
3
Supply, installation, connecting, testing and
commissioning of Hooters cum strobe min. 80 db
output
Nos 4 1000.00 4000.00
4
Supply, installation, connecting, testing and
commissioning of Manual Call Box in ABS plastic as
required complete.
Nos 4 650.00 2600.00
5Supply, installation, connecting, testing and
commissioning of Response indicator. Nos 30 200.00 6000.00
6
Supply installation, testing & Commissiong of
Adderessible Monitor Module Including Making etc
as required.
Nos 1 3000.00 3000.00
7Supply installation, testing & Commissiong of Control
Module Including Making etc as required.Nos 5 1850.00 9250.00
8
Supply, installation,connecting, testing and
commissioning of 6 Zone Fire Alarm Panel including
battery backup etc. complete as required. Set 1 32500.00 32500.00
Unit Qty. Rate In Rs. Amount In Rs.
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE
TECHNOLOGY PARK OF INDIA AT SALTLAKE, KOLKATA.
Sl.No. Description
BOQ : ELECTRICAL
9 Providing and fixing in position 1.2mm thick M.S.
outlet boxes for housing smoke detectors/heat
detectors including providing 3 mm thick hylam sheet
cover as required
a. 75mm x 75mm x 75mm Nos 60 125.00 7500.00
10Supply & laying of following grade with copper
conductor armoured FIRE SURVIVAL cable with
(EPR) Ethylene Propylene rubber insulation as per
IEC-60502:2004 Part-1 (Armoured), Retain circuit
integrity as per BS 6387 C.W.Z (armoured), BS-
8491:2008, BS 8434-2: 2009 (armoured),
(Resistance to fire at 950º C for 3 hours), as per
specifications in cable trays, clamped including
anchor fastners to wall with suitable clamps, saddles
fixing bolts,2 cable glands for each detector back
box, complete in all respect as required as per
specifications.(Red Colour)
a. 2 core x 1.5 sq. mm RM 650 150.00 97500.00
TOTAL CARRIED OVER TO SUMMARY 242100.00
DESCRIPTION UoM Qty.
Rate in Rs
Aomunt in
Rs
I. DATA HORIZONTAL COMPONENTS
1 Cat 6 Information Outlets - Blue -Active DATA (User side) Nos 75 300.00 22500.00
2Cat 6 Information Outlets - Green - Redundant DATA (User
Side) Nos 0 300.00 0.00
3 Cat 6 24 Port Jackpanel - loaded- A DATA Nos 4 9000.00 36000.00
4 Cat 6 24 Port Jackpanel - loaded- R DATA Nos 0 9000.00 0.00
5 Faceplate-Dual Nos 80 90.00 7200.00
6 Faceplate-Quad Nos 0 90.00 0.00
7 Cable Boxes - CAT 6 - Gray Boxes 15 6800.00 102000.00
8Patchcords- CAT 6- 7 fts-Blue- ( RJ45-RJ45 ) for Field &
Resource side (Active Data) Nos 75 290.00 21750.00
9Patchcords- CAT 6- 4 fts-Blue- ( RJ45-RJ45 ) for Resource side
(Active Data) Nos 75 280.00 21000.00
10 Blank Inserts Nos 35 20.00 700.00
II. VOICE HORIZONTAL COMPONENTS
1 Cat 6 Information Outlets - Yellow - Voice (User Side) Nos 70 300.00 21000.00
2 Cable Boxes - CAT 6- Blue Boxes 12 6800.00 81600.00
3 Cat 6 24 Port Jackpanel - loaded- A VOICE Nos 4 9000.00 36000.00
4 Cat 6 24 Port Jackpanel - loaded- VOICE Riser Nos 0 9000.00 0.00
5Patchcords- CAT 6- 4 fts-Yellow - ( RJ45-RJ45 ) for Source
side Nos 70 280.00 19600.00
III. VOICE BACKBONE COMPONENTS
1 25 Pair riser cable indoor type Mtrs. 50 200.00 10000.00
2 10 Pair Krone Modules Nos 8 200.00 1600.00
3 100 Pair MDF Boxes with accessories Nos 1 4500.00 4500.00
4 Hookup wire.(1 Roll of 100 metres) Roll 3 450.00 1350.00
5 Multipair cable-Cat3-50 pair( Indoor)-mts Roll 50 150.00 7500.00
6 6 core Multimode Optic Fibre Cable ( indoor) (OM3 Fiber) Roll 60 150.00 9000.00
IV. DATA RACKS ACCESSORIES For Networking Only
1
42 U Networking Rack (800 x1000 mm ) with accessories for
data ( Cisco Make)(2Nos server ra ck and 1No Networking
rack). Nos 0 45000.00 0.00
2 Horizantal wire manager-2U Nos 2 1200.00 2400.00
3 Power Distribution Channel ( 6 Points - 5A Socket) - Vertical Nos 2 1500.00 3000.00
4 Hardware packets Pkts 1 500.00 500.00
5Installation, terminating, crimping, commissioning, testing ,penta
scaning, documentation and certification of voice/data outlet
with all fixing accessories Points 160 150.00 24000.00
Total 433200.00
(VI) BOQ & ESTIAMATE FOR NETWORKING SYSTEM
INTERIOR DECORATION AND ANCILLARY WORKS FOR THE OFFICE SPACE OF THE SOFTWARE
TECHNOLOGY PARK OF INDIA AT SALTLAKE, KOLKATA.