TECHNICAL DATA BOOK OF INDUSTRIAL COATINGSnanophos.pk/downloads/4. NanoPhos Industrial... · TECHNICAL DATA BOOK OF INDUSTRIAL COATINGS 2 MAINTENANCE, REPAIRS AND CLEANING HMD Heavy

www.NanoPhos.comwww.NanoPhos-Marine.com

TECHNICALDATABOOK

OF

INDUSTRIALCOATINGS

2

MAINTENANCE,REPAIRSANDCLEANINGHMDHeavyDutyDegreaser.....................................................................................3HECHeavyDutyElectricCleaner...............................................................................4ARCGelRustRemover..............................................................................................5

EPOXYPRIMERS&TOPCOATSESPEpoxyShopPrimer.............................................................................................6EPREpoxyPrimer......................................................................................................8EZRNanoZincRichEpoxy..........................................................................................10EHBHighBuildEpoxy...............................................................................................12EENEpoxyEnamel.....................................................................................................14FGEFoodGradeEpoxy..............................................................................................162kMTIMetalThermalInsulator................................................................................28CTECoalTarEpoxy....................................................................................................20EPNPhenolic(NovolacType)Epoxy..........................................................................22GFEGlassFlakeEpoxy...............................................................................................24MEFEpoxyFiller........................................................................................................26EENovaAbrasionResistantEpoxy.............................................................................29SKGSeaKingFoulingReleaseEpoxy..........................................................................32

POLYURETHANEPRIMERS&TOPCOATS

CGUCoolGlossyStainResistantPolyurethaneEnamel............................................34

QUICKDRYINGPRIMERS&TOPCOATS

ACQAntiCorrosiveQuickDryAlkydPrimer...............................................................36SUPSurfaMixUniversalAcrylicPrimer.....................................................................38ENMEnamelAlkyd....................................................................................................40ASDAntiSlipCoating.................................................................................................42EZSNanoZincRichEthylSilicatePrimer....................................................................44STOVINGPRIMERS&TOPCOATSHRAAluminiumHeatResistantCoating...................................................................46THINNERSNPTANanoPhosThinnerA........................................................................................48NPTBNanoPhosThinnerB........................................................................................49

3

TECHNICALDATA

HMDHeavyDutyDegreaserPRODUCTDESCRIPTIONBiodegradable water-based cleaner that emulsifies and removes oil, grease andgrime. Cleans and eliminates by dissolving heavy oil residues in engine rooms,motors,machineryanddockorindustrialequipment.RECOMMENDEDUSEIdeal for removing grease, oil and sludge from the engineparts, tools,mechanicalbrakes, clutches, chains, cables,mouldings, components, bearings, generators andcompressors.KEYFEATURES• NotFlammable.Significantlyreducestheriskoffirecausedbyincidentalcontact

withliveelectricalequipmentorsolventstrappedbyinsulatingmaterials.• FastEvaporation.Minimizesdowntimeassociatedwith“clean-in-place”cleaning

methods.• Non-toxicandBiodegradable.APPLICATIONSpray liberally and allow running off. Use extension tube for hard-to-reach areas.Allow cleaned equipment to fully dry and vent before using or turning on. A dry,absorbent cloth can accelerate drying time. Do not use the product on plasticssurfaces such as acrylic, ABS and polycarbonate. If uncertain, check with themanufactureror testona small areabeforeusing.Donotusewhileequipment isenergized/turnedon.AVAILABLEPACKAGING4Land30LplasticcanistersNOTES AND PRECAUTIONS: Storage of closed containers, in controlled dry and enclosed space,away from sources of ignition and temperatures from 5οC to 35οC, for up to 18 months. TheTechnical Data should be read in conjunction with the Safety Data Sheets and Coating TechnicalSpecification. This product is for professional use only. For more information please contactNanoPhos:[email protected]@NanoPhos-Marine.com

4

TECHNICALDATA

HECHeavyDutyElectricCleanerPRODUCTDESCRIPTIONHigh performance cleaner for electric components that dirt has built-up. It candislodgeforeignelementsandcleancomponents.Preventselectriccontactfailure.Itleaves no residues. Quick-drying formulation (medium to fast type). Use on anyexposedsensitiveelectroniccomponentsandcontacts(enginecontrols,datasensorsandwiring).RECOMMENDEDUSEAsanelectricalcontactandpartscleanertoremovegrease,dirt,oil,fluxandothersurfacecontaminantsfromsensitiveelectrical/electronicdevices.Applicabletocleanmotorized instruments, control panels, electrically driven parts,motors, and otherelectronic devices requiring a fast acting, low residue degreasing agents.Recommendedforswitches,ACorDCcontacts,relays,PCboards,electricalmotorsandsensors.KEYFEATURES• FastEvaporation.Minimizesdowntimeassociatedwith“clean-in-place”cleaning

methods.• NoClass Ior IIOzoneDepletingChemicals.Alternative to1,1,1Trichloroethane

productswhilecomplyingwiththeEPAregulationsontheuseofozonedepletingchemicals.

APPLICATIONSpray liberally and allow running off. Do not apply to active equipment orwherethereisaresidualelectricalpotentialfromacomponentsuchasacapacitor.Spraysurface to be cleaned using 15 second bursts. For stubborn residues, repeatapplication.Fordifficultapplications,swabsorlintfreeclothsmaybeused.Allowtodrycompletelybeforere-activatingsystem.AVAILABLEPACKAGING5Land30Lmetaldrums.

NOTES AND PRECAUTIONS: Storage of closed containers, in controlled dry and enclosed space,away from sources of ignition and temperatures from 5οC to 35οC, for up to 18 months. TheTechnical Data should be read in conjunction with the Safety Data Sheets and Coating TechnicalSpecification. This product is for professional use only. For more information please contactNanoPhos:[email protected]@NanoPhos-Marine.com

5

TECHNICALDATA

ARCGelRustRemoverPRODUCTDESCRIPTIONARC is a rust remover in GEL form. Despite its acidic character, it contains nohydrochloricacid.ARCGeleffectively removes the rustoff thesurfaces topreparethemforprotectivecoatingapplication(primerandpaint).Italsocontainsflashrustinhibitorstoprotectearlycorrosioneffects.RECOMMENDEDUSEIdealcleanerforrustandhardwaterdeposits.Applicableevenwithsaltywater.GelformmakesARCGelRustRemovereasytoapplyonvertical,incliningmetalsurfaces,steelbarsorrails.KEYFEATURES• 100%Biodegradable,non-toxic,zeroVOC,non-flammableandwaterbased.• Fastreactionforrustremoval.• Containsnohydrochloricorchlorideingredients.• Multi-purpose:Frommetalsurfacestostainlesssteelboilers,heatexchangersor

pipes.APPLICATIONARCGelcanbeappliedbybrushonaverticalsurfacewithoutsagging.Letstandfor5minutes(longertimeneededforintenseaccumulationofstains),rubwithabrushorcloth if needed, and rinse with fresh water. Once rust or deposits have beenremoved,itisimportanttotreatmetalwithaprotectivecoating.AVAILABLEPACKAGING5Kgand15Kgplasticpails.


6

TECHNICALDATA

ESPEpoxyShopPrimerPRODUCTDESCRIPTION Two-component epoxy shop primer, pigmentedwith rust-inhibiting pigments. It ishighlyrecommendedasathincoatforblastcleanedsteelplateprotectionduringitsstorage and machining period. Easily applicable with both spraying and roller(manual)application.RECOMMENDEDUSE Itisdesignedforautomaticsprayapplicationaswellasmanualapplication.Asathin coat for blast cleaned steel plate protection, other structural during thestorageandbuildingperiod.APPROVALSANDCERTIFICATESApprovedbyLloyd’sRegisterasECPEpoxyConstructionPrimer, foruseasapre-fabricationprimer.Certificatescanbeprovideduponrequest. FILMTHICKNESSPERCOAT Minimum Maximum Recommended DryFilmThickness(μm): 10 50 30

WetFilmThickness(μm): 33 167 100

CoverageRate(m2/L): 30 6 10 Dryingtimesdifferentiateinminimumormaximumvalues.Maintainrecommendedvaluesduringapplication.CoveragerateisTheoreticalanddoesnotincludeanylosses. PROPERTIES

Type▶ ZincPhosphateEpoxyPolyamide TouchDryTime▶ 10min@20oC

Components▶ BaseA&HardenerB DryThroughTime▶ 20min@20oC

Colour▶ RedBrown,Cream Min.RecoatInterval▶ 30min@20oC

Thinner/CleaningMedium▶ NanoPhosThinnerA FullCuring▶ 7d@20oC

MixingRatio(v:v)▶ 4:1 InductionTime▶ 15min@20oC

VOC▶ <450g.L-1 Max.PotLife▶ 6h@20oC

Solids(%vol.)▶ 30±3 WaterResistance▶ Good

ServiceTemperature(Continuous,dry)▶

Max:150oCShort:180oC AbrasionResistance▶ Good

7

TECHNICALDATA

SURFACEPREPARATION Blasting: Sa 2½; with profiles between 30-75 μm, Reference standard: ISO 8501-1:2007. Allsurfacesshouldbeclean,dryandfreefromoil,greaseandotherforeignmattersorcontamination.PreparationaccordingtoISO8502-3:1992Testfortheassessmentofsurfacecleanliness. APPLICATION

ConventionalSpraying▶

Paintpressurepotwithpoweragitator,doubleairregulators,moisturetrap,1/2”IDfluidhose,5/16”IDairhose,DeVilbiss510gun,“E”tipandneedle,74or78aircap.

AirlessSpraying▶ Minimum:30:1pump.Nozzle:0.019”-0.023”

Brush▶ Recommendedapplicationmethodonlyforstripecoatingorsmallareas

Substrate temperature should be minimum 5℃ and at least 3℃ above air dew point. Goodventilationisrequiredtoensureproperdrying.PAINTSYSTEM Preceding:-Subsequent: Epoxy(EHB,EEN,FGE,2kMTI,CTE,EPN,CFE,EENOVA),CGU,ENM.

Avarietyofcombinationsamongprimersandtopcoatscanbeused.HEALTHANDSAFETY (A) Usenormalprecautionssuchasgloves,facemasks.(B) Adequateventilationmustbemaintained.(C) Explosionprooflights&electricalequipment.(D) Non-Sparkingshoes&toolsforworkersinarea.(E) This product contains flammable materials. Forbid all flames, smoking and

weldinginworkarea.(F) Avoid breathing of vapour, contact with skin or eyes. If product comes in

contact with skin or eyes, wash thoroughly with water and obtain medicalattention.

AVAILABLEPACKAGING 5Lunit(Total5Lintwometalcanisters,4:1,A:Bpervolume)20Lunit(Total20Lintwometalcanisters,4:1,A:Bpervolume) NOTES AND PRECAUTIONS: Storage of closed containers, in controlled dry and enclosed space,away from sources of ignition and temperatures from 5οC to 35οC, for up to 18 months. TheTechnical Data should be read in conjunction with the Safety Data Sheets and Coating TechnicalSpecification. This product is for professional use only. For more information please contactNanoPhos:[email protected]@NanoPhos-Marine.com

8

TECHNICALDATA

EPREpoxyPrimerPRODUCTDESCRIPTIONEPR is a universal two-component epoxy primer with anticorrosive long lastingaction. It is suitable for application on fiberglass, or metal surfaces. It containsanticorrosivepigments.Conformslowfirespreadabilityrequirements.RECOMMENDEDUSEAs an excellent quick drying primer for corrosion protection. Ideal for surfacesexposed to corrosive environments. It can be applied to all surfaces which needprimerbeforepainting.Fast-dryingcorrosionprotectivepaintthatsmoothensroughsurfaces.Itcanbecoveredbymostcoatings(epoxyornot).Itcanalsobeusedasasealer/bondinglayeroverexistingepoxyprimers.FILMTHICKNESSPERCOAT Minimum Maximum Recommended DryFilmThickness(μm): 80 150 100


CoverageRate(m2/L): 9.4 5 7.5 Dryingtimesdifferentiateinminimumormaximumvalues.Maintainrecommendedvaluesduringapplication.CoveragerateisTheoreticalanddoesnotincludeanylosses.APPROVALSANDCERTIFICATESApproved byDBI (Danish Institute of Fire and Security Technology), in accordancewiththerequirementsandthestandardsofIMOforlowflame-spread(ReferencetoIMO2010,FTPCode,Part5).Certificatescanbeprovideduponrequest.PROPERTIESType▶ EpoxyPolyamide TouchDryTime▶ 30min@20oC

Components▶ BaseA&HardenerB DryThroughTime▶ 4h@20oC

Colour▶ RedBrown,Cream Min.RecoatInterval▶ 6h@20oC




Solids(%vol.)▶ 75±3 WaterResistance▶ Excellent


Max:150oCShort:180oC AbrasionResistance▶ Excellent

9

TECHNICALDATA

SURFACEPREPARATIONCompatibleCoats:All surfaces shouldbeclean,dryand free fromoil, greaseandotherforeignmattersorcontamination.PreparationaccordingtoISO8502-3:1992TestfortheassessmentofsurfacecleanlinessaccordingtoISO8501-3:2006Visualassessmentofsurfacecleanliness.ImmersedBareSteel:BlastCleaningSa2½;withprofilesbetween30-75μm,oroncompatibleprimercoat.Referencestandard:ISO8501-1:2007.Non-ImmersedBare Steel:Power Tooling St 3, Sa 2where practicable.Referencestandard:ISO8501-1:2007.APPLICATION





Substrate temperature should be minimum 5℃ and at least 3℃ above air dew point. Goodventilationisrequiredtoensureproperdrying.PAINTSYSTEMPreceding:Epoxy(ESP,EPR,EZR),EZS,SUP,HRASubsequent:Epoxy(EHB,EEN,FGE,2kMTI,CTE,EPN,CFE,EENOVA),CGUHEALTHANDSAFETY

(A) Usenormalprecautionssuchasgloves,facemasks.(B) Adequateventilationmustbemaintained.(C) Explosionprooflights&electricalequipment.(D) Non-Sparkingshoes&toolsforworkersinarea.(E) This product contains flammablematerials. Forbid all flames, smoking and


contactwith skin or eyes,wash thoroughlywithwater and obtainmedicalattention.

AVAILABLEPACKAGING5Lunit(Total5Lintwometalcanisters,4:1,A:Bpervolume)20Lunit(Total20Lintwometalcanisters,4:1,A:Bpervolume)


10

TECHNICALDATA

EZRNanoZincRichEpoxyPRODUCTDESCRIPTION Two-component,NanoZincRich,CorrosionPassivatingCoating.Thecombinationofhigh concentration level of the epoxy binder with the high surface area zincnanoparticlesresultsinthehighestanti-corrosionperformance,evenintheharshestcorrosive environments (e.g. Seawater ballast tanks). Ideal primer in combinationwith advanced anticorrosion coating systems, in C5-I or C5-M (ISO 12944)environment.RECOMMENDEDUSE Asazincrich,corrosionprotection,high-performancecoating.Chemical,power&watertreatmentplants,refineries,oil&gaspipes,steampipes,bridges,barges,ships,drillingrigs&papermills. FILMTHICKNESSPERCOAT Minimum Maximum Recommended DryFilmThickness(μm): 60 120 75


CoverageRate(m2/L): 13.8 6.9 11.1 Dryingtimesdifferentiateinminimumormaximumvalues.Maintainrecommendedvaluesduringapplication.CoveragerateisTheoreticalanddoesnotincludeanylosses.APPROVALSANDCERTIFICATESUnderevaluationwithinthePerformanceStandardforProtectiveCoating(PSPC)fordedicated seawaterballast tanksof all typesof shipsof 500gross tonsandaboveandforthedouble-sideskinspacesofbulkcarriersof150minlengthandupwards. PROPERTIESType▶ nanoZincRich

EpoxyPolyamide TouchDryTime▶ 60min@20oC


Colour▶ Grey Min.RecoatInterval▶ 12h@20oC



VOC▶ 460g.L-1 Max.PotLife▶ 6h@20oC




11

TECHNICALDATA

SURFACEPREPARATION CompatibleCoats:All surfaces shouldbeclean,dryand free fromoil, greaseandotherforeignmattersorcontamination.PreparationaccordingtoISO8502-3:1992TestfortheassessmentofsurfacecleanlinessaccordingtoISO8501-3:2006Visualassessmentofsurfacecleanliness. Immersed Bare Steel: Blast Cleaning, Sa 2½; with profiles between 30-75 μm.Referencestandard:ISO 8501-1:2007.Non-ImmersedBareSteel:PowerTooling, St 3, Sa2wherepracticable.Referencestandard:ISO8501-1:2007. APPLICATION ConventionalSpraying▶ NotRecommendedAirlessSpraying▶ Minimum:30:1pump.Nozzle:0.019”-0.023”


Substrate temperature should be minimum 5℃ and at least 3℃ above air dew point. Goodventilationisrequiredtoensureproperdrying. PAINTSYSTEM Preceding:Epoxy(ESP),EZSSubsequent:Epoxy(EHB,EEN,FGE,2kMTI,CTE,EPN,CFE,EENOVA),CGU HEALTHANDSAFETY (A) Usenormalprecautionssuchasgloves,facemasks.(B) Adequateventilationmustbemaintained.(C) Explosionprooflights&electricalequipment.(D) Non-Sparkingshoes&toolsforworkersinarea.(E) This product contains flammable materials. Forbid all flames, smoking and



AVAILABLEPACKAGING5Lunit(Total5Lintwometalcanisters,4:1,A:Bpervolume)20Lunit(Total20Lintwometalcanisters,4:1,A:Bpervolume) NOTES AND PRECAUTIONS: Storage of closed containers, in controlled dry and enclosed space,away from sources of ignition and temperatures from 5οC to 35οC, for up to 18 months. TheTechnical Data should be read in conjunction with the Safety Data Sheets and Coating TechnicalSpecification. This product is for professional use only. For more information please contactNanoPhos:[email protected]@NanoPhos-Marine.com

12

TECHNICALDATA

EHBHighBuildEpoxyPRODUCTDESCRIPTIONAtwocomponenthighsolids,tarfree,epoxytiecoat,withpremiumanti-corrosiveand adhesion properties. Its “High Build” composition can achieve thick coatingswithoutsaggingorapplicationproblems.RECOMMENDEDUSEAs a tie coat, between primer, polyurethane and epoxy top coats, to improvedanticorrosive protection in corrosive environments and in normal atmosphericconditions.FILMTHICKNESSPERCOAT Minimum Maximum Recommended DryFilmThickness(μm): 60 140 80


CoverageRate(m2/L): 14.2 6.1 10.6 Dryingtimesdifferentiateinminimumormaximumvalues.Maintainrecommendedvaluesduringapplication.CoveragerateisTheoreticalanddoesnotincludeanylosses.PROPERTIESType▶ EpoxyPolyamide TouchDryTime▶ 30min@20oC


Colour▶ RedBrown,Cream Min.RecoatInterval▶ Max.RecoatInterval▶

6h@20oC3d@20oC







SURFACEPREPARATIONCompatible Coats:All surfaces should be clean, dry and free fromoil, grease andother foreignmattersor contamination.Preparationaccording to ISO8502-3:1998Testfortheassessmentofsurfacecleanliness.

13

TECHNICALDATA

APPLICATION


Brush▶Recommendedapplicationmethodonlyforstripecoatingorsmallareas

Substratetemperatureshouldbeminimum5℃andatleast3℃aboveairdewpoint.Goodventilationisrequiredtoensureproperdrying.PAINTSYSTEMPreceding:Epoxy(ESP,EPR,EZR),EZSSubsequent:Epoxy(EHB,EEN,FGE,2kMTI,CTE,EPN,CFE,EENOVA),CGUHEALTHANDSAFETY(A) Usenormalprecautionssuchasgloves,facemasks.(B) Adequateventilationmustbemaintained.(C) Explosionprooflights&electricalequipment.(D) Non-Sparkingshoes&toolsforworkersinarea.(E) This product contains flammable materials. Forbid all flames, smoking and



AVAILABLEPACKAGING5Lunit(Total5Lintwometalcanisters,4:1,A:Bpervolume)20Lunit(Total20Lintwometalcanisters,4:1,A:Bpervolume)NOTES AND PRECAUTIONS: Storage of closed containers, in controlled dry and enclosed space,away from sources of ignition and temperatures from 5οC to 35οC, for up to 18 months. TheTechnical Data should be read in conjunction with the Safety Data Sheets and Coating TechnicalSpecification. This product is for professional use only. For more information please contactNanoPhos:[email protected]@NanoPhos-Marine.com

14

TECHNICALDATA

EENEpoxyEnamelPRODUCTDESCRIPTIONEENPolyamideEpoxyEnamelpresents ahigh gloss, excellentweathering resistantandexcellentabrasionresistancecoating.RECOMMENDEDUSEEENcanbeusedasanepoxyfinishcoatinmediumtoseverelycorrosiveatmosphericenvironment.Aquickdrying,hard, chemical resistantcoating.Canbeappliedoverintact existing conventional systems and over suitable primers. Good adhesionpropertiesinwetanddryexposureconditions.APPROVALSANDCERTIFICATESApproved byDBI (Danish Institute of Fire and Security Technology), in accordancewiththerequirementsandthestandardsofIMOforlowflame-spread(ReferencetoIMO2010,FTPCode,Part5).Certificatescanbeprovideduponrequest.

FILMTHICKNESSPERCOAT Minimum Maximum Recommended DryFilmThickness(μm): 50 120 80


CoverageRate(m2/L): 13 5.4 8.1 Dryingtimesdifferentiateinminimumormaximumvalues.Maintainrecommendedvaluesduringapplication.CoveragerateisTheoreticalanddoesnotincludeanylosses.PROPERTIESType▶ EpoxyPolyamide TouchDryTime▶ 1h@20oC


Colour▶ ColourCard Min.RecoatInterval▶ 12h@20oC







15

TECHNICALDATA

SURFACEPREPARATIONCompatibleCoats:All surfaces shouldbeclean,dryand free fromoil, greaseandotherforeignmattersorcontamination.PreparationaccordingtoISO8502-3:1992Testfortheassessmentofsurfacecleanliness.APPLICATION





Substrate temperature should be minimum 5℃ and at least 3℃ above air dew point. Goodventilationisrequiredtoensureproperdrying.PAINTSYSTEMPreceding:Epoxy(ESP,EPR,EZR),EZSSubsequent:-HEALTHANDSAFETY


weldinginworkarea.(F) Avoidbreathingofvapour, contactwith skinoreyes. Ifproductcomes in

contactwithskinoreyes,washthoroughlywithwaterandobtainmedicalattention.


16

TECHNICALDATA

FGE

FoodGradeEpoxy PRODUCTDESCRIPTION Two component 100% solids, high performance, food safe, epoxy coating. Zeromigrationoffoodcontaminants. RECOMMENDEDUSE Asaprotectivelinerfortanksandmachineryincontactwithfoodproducts.FGEcanbeappliedontopofprotectivecoatingsystemtoensurefoodsafetystandards. FILMTHICKNESSPERCOAT Minimum Maximum Recommended DryFilmThickness(μm): 80 140 100


CoverageRate(m2/L): 12.5 7.1 10 Dryingtimesdifferentiateinminimumormaximumvalues.Maintainrecommendedvaluesduringapplication.CoveragerateisTheoreticalanddoesnotincludeanylosses. PROPERTIES Type▶ EpoxyCycloaliphatic

Amine TouchDryTime▶ 30min@20oC


Colour▶ White,Grey,RedBrown Min.RecoatInterval▶ 6h@20oC







SURFACEPREPARATION Compatible Coats:All surfaces should be clean, dry and free fromoil, grease andother foreignmattersor contamination.Preparationaccording to ISO8502-3:1992Testfortheassessmentofsurfacecleanliness. Non-ImmersedBareSteel:PowerTooling, St 3, Sa2wherepracticable.Referencestandard:ISO8501-1:2007.

17

TECHNICALDATA APPLICATION





Substrate temperature should be minimum 5℃ and at least 3℃ above air dew point. Goodventilationisrequiredtoensureproperdrying.PAINTSYSTEM Preceding:-Subsequent:- HEALTHANDSAFETY (A) Usenormalprecautionssuchasgloves,facemasks.(B) Adequateventilationmustbemaintained.(C) Explosionprooflights&electricalequipment.(D) Non-Sparkingshoes&toolsforworkersinarea.(E) This product contains flammable materials. Forbid all flames, smoking and

weldinginworkarea.(F) Avoidbreathingofvapour,contactwithskinoreyes.Ifproductcomesincontact

withskinoreyes,washthoroughlywithwaterandobtainmedicalattention. AVAILABLEPACKAGING5Lunit(Total5Lintwometalcanisters,4:1,A:Bpervolume)20Lunit(Total20Lintwometalcanisters,4:1,A:Bpervolume)


18

TECHNICALDATA

2kMTIMetalThermalInsulatorPRODUCTDESCRIPTION Two-component, thermal insulating coating. An innovative, thermal insulatingcoatingutilizingsphericalparticlesthatimpartexceptionalinsulatingpropertiestoavariety of substrates. Ideal for insulating pipes, valves, tanks, structural steel, orother substrateswhere thermal improvement and protection is desired. Part of adurable, corrosion-resistant coating system that bonds to the substrate, greatlyreducing the issues associatedwith corrosion under insulation (CuI). Replacementsolution for jacket insulation of steam/oil pipes that require thermal insulationcombinedwiththerobustnessofanepoxycoating.RECOMMENDEDUSEAs a thermal insulating coating to prevent heat losses in heat exchangers, heatedtanks and (steam) pipes, and to increase the overall energy efficiency. Ideal forenginerooms,heatexchangersandsteampipestocombineanticorrosiveprotectionwithenergyprofileupgrade.FILMTHICKNESSPERCOAT Minimum Maximum Recommended DryFilmThickness(μm): 150 500 325


CoverageRate(m2/L): 5.7 1.7 2.6 Dryingtimesdifferentiateinminimumormaximumvalues.Maintainrecommendedvaluesduringapplication.CoveragerateisTheoreticalanddoesnotincludeanylosses.PROPERTIESType▶ LowDensity

EpoxyPolyamide TouchDryTime▶ 2h@20oC









19

TECHNICALDATA

SURFACEPREPARATION Compatible Coats:All surfaces should be clean, dry and free fromoil, grease andother foreignmattersor contamination.Preparationaccording to ISO8502-3:1992Testfortheassessmentofsurfacecleanliness. Non-ImmersedBareSteel:PowerTooling, St 3, Sa2wherepracticable.Referencestandard:ISO8501-1:2007.APPLICATIONConventionalSpraying▶ NotrecommendedAirlessSpraying▶ Minimum:30:1pump.Nozzle:0.019”-0.023”


Substrate temperature should be minimum 5℃ and at least 3℃ above air dew point. Goodventilationisrequiredtoensureproperdrying.PAINTSYSTEMPreceding:Epoxy(ESP,EPR,EZR)Subsequent:-HEALTHANDSAFETY(A) Usenormalprecautionssuchasgloves,facemasks.(B) Adequateventilationmustbemaintained.(C) Explosionprooflights&electricalequipment.(D) Non-Sparkingshoes&toolsforworkersinarea.(E) This product contains flammable materials. Forbid all flames, smoking and




20

TECHNICALDATA

CTECoalTarEpoxyPRODUCTDESCRIPTIONTwo-component epoxy coal tar coating. It is a high gloss coating with excellentresistancetoseawater,crudeoil,varioussoilchemicalsandsoilstress.RECOMMENDEDUSEAs final coat onmetallic surfaces, providing long-term anti corrosive protectionand excellent durability especially in constructions exposed to high humidityenvironmentsorintendedtobeplacedintotheground,suchaspipes,tanksetc.FILMTHICKNESSPERCOAT Minimum Maximum Recommended DryFilmThickness(μm): 50 120 80


CoverageRate(m2/L): 15 6.3 9.4 Dryingtimesdifferentiateinminimumormaximumvalues.Maintainrecommendedvaluesduringapplication.CoveragerateisTheoreticalanddoesnotincludeanylosses.PROPERTIESType▶ CoalTarEpoxy TouchDryTime▶ 1h@20oC


Colour▶ Black Min.RecoatInterval▶ 12h@20oC








21

TECHNICALDATA

APPLICATION









22

TECHNICALDATA

EPNPhenolic(NovolacType)EpoxyPRODUCTDESCRIPTIONTwo-component phenolic epoxy (novolac type) coating. It has very good adhesionwithchemicalresistanceagainstcorrosivefactors,suchasseawater,hydrocarbons,crude oil, ketones, esters alcohols, halocarbons, acids (includingsulphated/sulphuratedenvironment)andbases.RECOMMENDEDUSEAsafinalcoatforEngineroomshields, fueltanks(gasoline,crudeoil, jetfuel),oil,hydrocarbonpipingandanysurfacewhereprotectionagainstchemicalsisrequired.

FILMTHICKNESSPERCOAT Minimum Maximum Recommended DryFilmThickness(μm): 50 120 80


CoverageRate(m2/L): 17.4 7.3 10.9 Dryingtimesdifferentiateinminimumormaximumvalues.Maintainrecommendedvaluesduringapplication.CoveragerateisTheoreticalanddoesnotincludeanylosses.PROPERTIESType▶ NovolacEpoxyType TouchDryTime▶ 1h@20oC


Colour▶ GreyColourCard Min.RecoatInterval▶ 12h@20oC







SURFACEPREPARATIONCompatibleCoats:All surfaces shouldbeclean,dryand free fromoil, greaseandotherforeignmattersorcontamination.PreparationaccordingtoISO8502-3:1992Testfortheassessmentofsurfacecleanliness.

23

TECHNICALDATA

APPLICATION









24

TECHNICALDATA

GFEGlassFlakeEpoxyPRODUCTDESCRIPTIONTwo-componentepoxypolyamide,highbuildcoatingreinforcedwithhighcontentofGlassFlakes.GFEpresentsahighimpactandabrasionresistancecoating,combinedwithcorrosionprotectionproperties.RECOMMENDEDUSEAsaself-primed,highbuildcoatingprimarilyforareassubjecttoabrasionand/ortoahighlycorrosiveenvironment.FILMTHICKNESSPERCOAT Minimum Maximum Recommended DryFilmThickness(μm): 60 120 80


CoverageRate(m2/L): 13 6.5 9.8 Dryingtimesdifferentiateinminimumormaximumvalues.Maintainrecommendedvaluesduringapplication.CoveragerateisTheoreticalanddoesnotincludeanylosses.PROPERTIESType▶ GlassFlakeReinforced



Colour▶ GreyColourCard Min.RecoatInterval▶ 12h@20oC








25

TECHNICALDATA

APPLICATION





Substrate temperature should be minimum 5℃ and at least 3℃ above air dew point. Goodventilationisrequiredtoensureproperdrying.PAINTSYSTEMPreceding:Epoxy(ESP,EPR,EZR)Subsequent:Epoxy(EEN)orPolyurethane(CGU)HEALTHANDSAFETY(A) Usenormalprecautionssuchasgloves,facemasks.(B) Adequateventilationmustbemaintained.(C) Explosionprooflights&electricalequipment.(D) Non-Sparkingshoes&toolsforworkersinarea.(E) This product contains flammable materials. Forbid all flames, smoking and




26

TECHNICALDATA

MEFEpoxyFillerPRODUCTDESCRIPTIONMEFChemicalResistant,ThermalInsulatingEpoxyFillerisalowdensity,solventfree,novolac-type,epoxyfillerthatcombinesthermalinsulatingpropertieswithchemicalresistanceagainstcorrosivefactors,suchasseawater,hydrocarbons,ketones,estersalcohols, halocarbons, acids (including sulphated/sulphurated environment) andbases.Itisconsideredahighbuildepoxyfiller,asitisapplicableinthickcoats(upto8mm)withoutsagging.Itcureswithoutvolumetricchange,makingitapplicableasafillingmedium.RECOMMENDEDUSERecommended as a high-performance filler, in cases thermal insulating propertiesand chemical resistance should be combined. Engine room shields, fuel tanks(gasoline,crudeoil,jetfuel),oilandhydrocarbon.APPROVALSANDCERTIFICATESConsidered forapproval testingunder thenew IMOPSPCCOTresolutionMSC288(87).FILMTHICKNESSPERCOAT Minimum Maximum Recommended DryFilmThickness(mm): 1 8 3

WetFilmThickness(mm): 1 8 3

CoverageRate(m2/L): 1 0.1 0.3 Dryingtimesdifferentiateinminimumormaximumvalues.Maintainrecommendedvaluesduringapplication.CoveragerateisTheoreticalanddoesnotincludeanylosses.PROPERTIESType▶ ThermalInsulating

PhenolEpoxyFiller TouchDryTime▶ 10h@20oC


Colour▶ RedBrownOffWhite Min.RecoatInterval▶ 12h@20oC







27

TECHNICALDATA

SURFACEPREPARATIONCompatibleCoats:Allsurfacesshouldbeclean,dryandfreefromoil,greaseandotherforeignmattersorcontamination.PreparationaccordingtoISO8502-3:1998Testfortheassessmentofsurfacecleanliness.APPLICATIONAirlessSpraying▶ NotApplicable.Brush▶ NotApplicable.Trowel▶ Use a good quality trowel to achieve desired thickness and

surfacefinish.Donotexceed8mminthickness.Filling▶ Emptytheactivatedproductinthedesiredform.Donotremove

formbeforefullcuringhasbeenachieved.Substrate temperature shouldbeminimum5℃ andat least 3℃ aboveair dewpoint.Goodventilationisrequiredtoensureproperdrying.PAINTSYSTEMPreceding:Epoxy(ESP,EPR,EZR),EZSSubsequent:Epoxy(EHB,EEN,FGE,2kMTI,CTE,EPN,CFE,EENova)orPolyurethane(CGU)HEALTHANDSAFETY(A) Usenormalprecautionssuchasgloves,facemasks.(B) Adequateventilationmustbemaintained.(C) Explosionprooflights&electricalequipment.(D) Non-Sparkingshoes&toolsforworkersinarea.(E) This product contains flammable materials. Forbid all flames, smoking and



AVAILABLEPACKAGING20Lunit(Total20Lintwometalcanisters,4:1,A:Bpervolume)NOTES AND PRECAUTIONS: Storage of closed containers, in controlled dry and enclosed space,away from sources of ignition and temperatures from 5οC to 35οC, for up to 18 months. TheTechnical Data should be read in conjunction with the Safety Data Sheets and Coating TechnicalSpecification. This product is for professional use only. For more information please contactNanoPhos:[email protected]@NanoPhos-Marine.com

28

TECHNICALDATA

EENovaAbrasionResistantEpoxy PRODUCTDESCRIPTION EENova is unique among epoxy polyamide coatings for incorporating siliconelastomer nanoparticles, i.e. a soft, elastomer core, directly on the epoxy resinbinder. In thisway, impact/abrasion energy elements are introduced in the epoxymatrix without affecting durability. The energy absorbing particles promote theabrasionresistanceandabsorbacuteabrasiveforcesprotectingtheintegrityofboththecoatingandthesubstrate.RECOMENDEDUSEEENovaisapolyamideepoxycoatingforuseonsubstrates,wheresevereimpactorabrasion loads are experienced. Barges, clamshell grabs, cargo hold or twistlockimpactingsurfacesareprominentapplicationareas.FILMTHICKNESSPERCOAT Minimum Maximum Recommended DryFilmThickness(μm): 100 250 150


CoverageRate(m2/L): 8 3.2 5.33 Dryingtimesdifferentiateinminimumormaximumvalues.Maintainrecommendedvaluesduringapplication.CoveragerateisTheoreticalanddoesnotincludeanylosses.PROPERTIESType▶ Abrasion/ImpactAbsorbing



Colour▶ RedBrownColourCard Min.RecoatInterval▶ 10h@20oC







29

TECHNICALDATA

SURFACEPREPARATION Compatible Coats:All surfaces should be clean, dry and free fromoil, grease andother foreignmattersor contamination.Preparationaccording to ISO8502-3:1992Testfortheassessmentofsurfacecleanliness. Non-ImmersedBareSteel:PowerTooling, St 3, Sa2wherepracticable.Referencestandard:ISO8501-1:2007. APPLICATION





Substrate temperature should be minimum 5℃ and at least 3℃ above air dew point. Goodventilationisrequiredtoensureproperdrying.PAINTSYSTEMPreceding:Epoxy(ESP,EPR,EZR)Subsequent:-HEALTHANDSAFETY




AVAILABLEPACKAGING20Lunit(Total20Lintwometalcanisters,4:1,A:Bpervolume) NOTES AND PRECAUTIONS: Storage of closed containers, in controlled dry and enclosed space,away from sources of ignition and temperatures from 5οC to 35οC, for up to 18 months. TheTechnical Data should be read in conjunction with the Safety Data Sheets and Coating TechnicalSpecification. This product is for professional use only. For more information please contactNanoPhos:[email protected]@NanoPhos-Marine.com

30

TECHNICALDATA

SKGSeaKingFoulingReleaseEpoxy PRODUCTDESCRIPTIONTheultimateepoxy foulingreleasecoating,presenting long lasting lowfrictionandsuperiorreleaseproperties,basedonnanotechnology.Containsnobiocides.Basedon a PolyDiMethylSiloxane modified epoxy matrix. SeaKing is No-Self PolishingCoatingapplicableonseawaterimmersedstructures.Eventhoughitdoesn’tpreventfoulinggrowth,theamphiphiliccoatingcharacterallowsthereleaseofaccumulatedfouling by soft removal methods. The resulting surface returns to the originalappearance and roughness, even after prolonged exposure. Ideal for stationary,seawater structures that antifouling coatings will eventually present fadingperformance.RECOMMENDEDUSEAsabiocidefreecoatingforoffshorepillarsandseawaterimmersedstructures.APPROVALSANDCERTIFICATESApprovedbyDNV-GL,inaccordancewiththerequirementsandthestandardsofIMOAntifoulingSystemConvention.Certificatescanbeprovideduponrequest. FILMTHICKNESSPERCOAT Minimum Maximum Recommended DryFilmThickness(μm): 75 125 100


CoverageRate(m2/L): 10 6 7.5 Dryingtimesdifferentiateinminimumormaximumvalues.Maintainrecommendedvaluesduringapplication.CoveragerateisTheoreticalanddoesnotincludeanylosses.PROPERTIESType▶ SiliconModified



Colour▶ RedBrown,BlackColourCard Min.RecoatInterval▶ 24h@20oC







31

TECHNICALDATA






Substrate temperature should be minimum 5℃ and at least 3℃ above air dew point. Goodventilationisrequiredtoensureproperdrying.PAINTSYSTEMPreceding:Epoxy(ESP,EPR,EZR)Subsequent:-HEALTHANDSAFETY





32

TECHNICALDATA

CGUCoolGlossyStainResistantPolyurethaneEnamelPRODUCTDESCRIPTIONCGUisanacrylic(aliphatic)polyurethanecoatingwithoutstandingcolourretentionabilities. This coating has exceptional resistance to weathering, staining andcorrosiveenvironment.Canbeusedinexteriororinteriorapplications,orwherevera superior gloss and colour retention finish is desired. Special Nanostructuredingredients reflect incident heat radiation. CGU presents high durability, colourstability and high yellowing resistance against UV radiation, even after prolongedexposure.RECOMMENDEDUSEIdealfortheexternalprotectionofsteelstructureslikefuel/chemicalstoragetanks,pipelines, refineries,nuclear stationsetc. ExceptionalprotectionagainstUVand IR(heat) radiation. Does not yellow. A highly resistant coating to abrasion andchemicals.FILMTHICKNESSPERCOAT Minimum Maximum Recommended DryFilmThickness(μm): 60 120 80


CoverageRate(m2/L): 10 5 7.5 Dryingtimesdifferentiateinminimumormaximumvalues.Maintainrecommendedvaluesduringapplication.CoveragerateisTheoreticalanddoesnotincludeanylosses.PROPERTIESType▶ AcrylicAliphatic

Polyurethane TouchDryTime▶ 30min@20oC


Colour▶ PureWhiteColourCard Min.RecoatInterval▶ 12h@20oC

Thinner/CleaningMedium▶ NanoPhosThinnerB FullCuring▶ 2d@20oC






33

TECHNICALDATA






Substrate temperature should be minimum 5℃ and at least 3℃ above air dew point. Goodventilationisrequiredtoensureproperdrying.PAINTSYSTEMPreceding:Epoxy(ESP,EPR,EZR),EZSSubsequent:-HEALTHANDSAFETY





34

TECHNICALDATA

ACQ

AntiCorrosiveQuickDryAlkydPrimer

PRODUCTDESCRIPTION One-component,corrosioninhibitive,highqualityalkydprimerforsteelexposedtoasoftormoderatelycorrosiveenvironment.Quickdryingandeasilyapplicable. Itpresentsexcellentadhesion,flexibilityandhighanti-corrosiveprotectionduetoitsspecialpigmentsofzincphosphateandzincoxide.Itcontainsnoleadcompounds.Non-toxic. RECOMMENDEDUSE Asacorrosioninhibitive,highqualityprimerforexposedsteel.Useoveralkydstoupgradesystem.Excellentforprimingstoragetanks,industrialplants,machinery,andothermetalsubjectedtoheavyindustrialuseandexteriorexposure. FILMTHICKNESSPERCOAT Minimum Maximum Recommended DryFilmThickness(μm): 40 80 60


CoverageRate(m2/L): 13.8 6.9 9.2 Dryingtimesdifferentiateinminimumormaximumvalues.Maintainrecommendedvaluesduringapplication.CoveragerateisTheoreticalanddoesnotincludeanylosses.PROPERTIESType▶ AlkydAnticorrosive

Primer TouchDryTime▶ 2h@20oC

Components▶ SingleComponent DryThroughTime▶ 3h@20oC

Colour▶ RedBrown,Grey,White Min.RecoatInterval▶ 3h@20oC

Thinner/CleaningMedium▶ NanoPhosThinnerB FullCuring▶ 24h@20oC

MixingRatio(v:v)▶ SingleComponent InductionTime▶ -

VOC▶ <425g.L-1 Max.PotLife▶ -




35

TECHNICALDATA SURFACEPREPARATION Compatible Coats:All surfaces should be clean, dry and free fromoil, grease andother foreignmattersor contamination.Preparationaccording to ISO8502-3:1992Testfortheassessmentofsurfacecleanliness. Non-ImmersedBareSteel:PowerTooling, St 3, Sa2wherepracticable.Referencestandard:ISO8501-1:2007. APPLICATIONAirlessSpraying▶ Minimum:30:1pump.Nozzle:0.018”-0.020”


Substrate temperature should be minimum 5℃ and at least 3℃ above air dew point. Goodventilationisrequiredtoensureproperdrying.PAINTSYSTEMPreceding:-Subsequent:Alkyd(ENM,ASD)HEALTHANDSAFETY




AVAILABLEPACKAGING5L&20Lmetalcanisters NOTES AND PRECAUTIONS: Storage of closed containers, in controlled dry and enclosed space,away from sources of ignition and temperatures from 5οC to 35οC, for up to 18 months. TheTechnical Data should be read in conjunction with the Safety Data Sheets and Coating TechnicalSpecification. This product is for professional use only. For more information please contactNanoPhos:[email protected]@NanoPhos-Marine.com

36

TECHNICALDATA

SUPSurfaMixUniversalAcrylicPrimerPRODUCTDESCRIPTIONOne-componentacrylicprimer,basedonaspecialengineered,lowviscosityandfast-curing resin that can anchor on themost demanding surfaces: galvanized ferrous,aluminiumsurfacesorvitreous,glazedandlowporositysurfaces.SurfaMixUniversalPrimerexhibitsgoodwettingandlowtouch-dry/curingtime.Extremelyweatheringand UV resistant coating. Its application results in an elastic membrane that canwithstand temperature expansion/contraction and prevent cracking. Provides aperfectsubstrateforfinalcoating.RECOMMENDEDUSE As a corrosion inhibitive high quality Primer for galvanized steel or aluminiumexposed to corrosive environment. Excellent for priming metallic, other thancarbonsteelsubstratessubjectedtoheavyindustrialuseandtoexteriorexposure. FILMTHICKNESSPERCOAT Minimum Maximum Recommended DryFilmThickness(μm): 80 140 110


CoverageRate(m2/L): 8.1 4.6 5.9 Dryingtimesdifferentiateinminimumormaximumvalues.Maintainrecommendedvaluesduringapplication.CoveragerateisTheoreticalanddoesnotincludeanylosses.PROPERTIESType▶ AcrylicPrimerfor

Non-FerrousSubstrates TouchDryTime▶ 45min@20oC


Colour▶ Grey,White Min.RecoatInterval▶ 3h@20oC







37



Substrate temperature should be minimum 5℃ and at least 3℃ above air dew point. Goodventilationisrequiredtoensureproperdrying.PAINTSYSTEMPreceding:-Subsequent:Alkyd(ENM,ASD),SolventbasedAcrylicTopCoats,CGUHEALTHANDSAFETY





38

TECHNICALDATA

ENMEnamelAlkyd

PRODUCTDESCRIPTION ENMEnamelisahighglossalkydfinishcoating,possessingexcellentcolourstabilityandglossretentionforinteriorandexteriorapplications.Engineeredforapplicationover alkyd primers. ENM offers long-lasting performance and anticorrosionprotection.Optimizedrheologymakes iteasytoapplyonverticalsurfaces,even inpresence of high moisture levels. Excellent adhesion to most conventional top-coatings. RECOMMENDEDUSE Asa finishcoat formetallic surfaces.Aquickdrying,hard,water resistant coating.Canbeappliedoverintactexistingconventionalsystemsandoversuitableprimers.Goodadhesionpropertiesinwetanddryexposureconditions. FILMTHICKNESSPERCOAT Minimum Maximum Recommended DryFilmThickness(μm): 50 100 70


CoverageRate(m2/L): 11 5.5 7.9 Dryingtimesdifferentiateinminimumormaximumvalues.Maintainrecommendedvaluesduringapplication.CoveragerateisTheoreticalanddoesnotincludeanylosses.PROPERTIESType▶ AlkydAnticorrosive

EnamelTopCoat TouchDryTime▶ 90min@20oC


Colour▶ RedBrown,Grey,WhiteColourCard Min.RecoatInterval▶ 7h@20oC







39



Substrate temperature should be minimum 5℃ and at least 3℃ above air dew point. Goodventilationisrequiredtoensureproperdrying.PAINTSYSTEMPreceding:AlkydACQ,AcrylicSUPSubsequent:-HEALTHANDSAFETY





40

TECHNICALDATA

ASD

AntiSlipDeckCoating PRODUCTDESCRIPTION One-component self-priming alkyd coating. Exhibits high wearing resistance andnear-zero gloss. Fast drying and low-dirt pickup.Does not yellowor flake, even inharsh weathering conditions. Protects against corrosion. Applicable in adverseenvironmentalconditions.Usedasanabrasionresistantandfinalanti-slipcoatingonmetal,concretesurfacesandindustrialfloors. RECOMMENDEDUSE Asanabrasionresistantandfinalanti-slipcoating. FILMTHICKNESSPERCOAT Minimum Maximum Recommended DryFilmThickness(μm): 80 120 100


CoverageRate(m2/L): 11 5.5 7.9 Dryingtimesdifferentiateinminimumormaximumvalues.Maintainrecommendedvaluesduringapplication.CoveragerateisTheoreticalanddoesnotincludeanylosses.PROPERTIESType▶ Alkyd

AntiSlipTopCoat TouchDryTime▶ 60min@20oC


Colour▶ Blue,Grey,WhiteColourCard Min.RecoatInterval▶ 6h@20oC







41



Substrate temperature should be minimum 5℃ and at least 3℃ above air dew point. Goodventilationisrequiredtoensureproperdrying.PAINTSYSTEMPreceding:AlkydACQSubsequent:-HEALTHANDSAFETY




AVAILABLEPACKAGING20Lmetalcanisters NOTES AND PRECAUTIONS: Storage of closed containers, in controlled dry and enclosed space,away from sources of ignition and temperatures from 5οC to 35οC, for up to 18 months. TheTechnical Data should be read in conjunction with the Safety Data Sheets and Coating TechnicalSpecification. This product is for professional use only. For more information please contactNanoPhos:[email protected]@NanoPhos-Marine.com

42

TECHNICALDATA

EZSNanoZincRichEthylSilicatePrimerPRODUCTDESCRIPTION Two-component, self-healing inorganic zinc ethyl silicate primer. It has excellentchemical resistance. It is heat resistant up to 590oC. Offers cathodic anticorrosionprotectioneveninpaintspotsthathavesufferedabrasivefailure.RECOMMENDEDUSE EZS is recommended for long-term protection inmoderately to severely corrosiveenvironment. Ideal primer in combination with advanced anticorrosion coatingsystems,inC5-IorC5-M(ISO12944)environment. FILMTHICKNESSPERCOAT Minimum Maximum Recommended DryFilmThickness(μm): 75 125 100


CoverageRate(m2/L): 10 6 7.5 Dryingtimesdifferentiateinminimumormaximumvalues.Maintainrecommendedvaluesduringapplication.CoveragerateisTheoreticalanddoesnotincludeanylosses.PROPERTIESType▶ InorganicEthylZincSilicate TouchDryTime▶ 30min@20oC









43

TECHNICALDATA






Substrate temperature should be minimum 5℃ and at least 3℃ above air dew point. Goodventilationisrequiredtoensureproperdrying.PAINTSYSTEMPreceding:-Subsequent:Epoxy,CGUHEALTHANDSAFETY





44

TECHNICALDATA

HRAAluminiumHeatResistantCoating

PRODUCTDESCRIPTION One-componentsiliconeresincoatingwithaluminiumpigments.Itisaheatresistantindustrialcoatingtoofferexcellentresistanceinhightemperatureenvironment(upto600oC),combinedwithanticorrosiveprotection. RECOMMENDEDUSE Asafinishcoatformetallicsurfacessubjecttohightemperaturesupto600oC,suchashotpipelines,exhaustpipes,smokestacks,heatingbodies,stovepipes,boilersetc.FILMTHICKNESSPERCOAT Minimum Maximum Recommended DryFilmThickness(μm): 50 100 70


CoverageRate(m2/L): 15 7.5 10.7 Dryingtimesdifferentiateinminimumormaximumvalues.Maintainrecommendedvaluesduringapplication.CoveragerateisTheoreticalanddoesnotincludeanylosses.PROPERTIESType▶ Aluminiumpigmented

SiliconeResin TouchDryTime▶ 3h@20oC


Colour▶ AluminiumOnly Min.RecoatInterval▶ 6h@20oC


MixingRatio(v:v)▶ - InductionTime▶ -





45

TECHNICALDATA






Substrate temperature should be minimum 5℃ and at least 3℃ above air dew point. Goodventilationisrequiredtoensureproperdrying.PAINTSYSTEMPreceding:EZSSubsequent:-HEALTHANDSAFETY




AVAILABLEPACKAGING20Lmetalcanisters NOTES AND PRECAUTIONS: Storage of closed containers, in controlled dry and enclosed space,away from sources of ignition and temperatures from 5οC to 35οC, for up to 18 months. TheTechnical Data should be read in conjunction with the Safety Data Sheets and Coating TechnicalSpecification. This product is for professional use only. For more information please contactNanoPhos:[email protected]@NanoPhos-Marine.com

46

TECHNICALDATA

NPTANanoPhosThinnerAProductDescriptionOrganic,solventbasedthinnerforepoxypaintsystems.TypicalPropertiesDensity/VOC:0,85±0,02(850-870g.L-1).,Mediumevaporationrate,Flashpoint>23οC.AvailablePackaging5Land20Lmetalcanisters.NOTES AND PRECAUTIONS: Storage of closed containers, in controlled dry and enclosed space,away from sources of ignition and temperatures from 5οC to 35οC, for up to 18 months. TheTechnical Data should be read in conjunction with the Safety Data Sheets and Coating TechnicalSpecification. This product is for professional use only. For more information please contactNanoPhos:[email protected]@NanoPhos-Marine.com

47

TECHNICALDATA

NPTBNanoPhosThinnerBProductDescriptionOrganic,solventbasedthinnerforalkyd/acrylic/zincethylsilicate/PU,paintsystems.TypicalPropertiesDensity/VOC:0,85±0,02(780g.L-1),Mediumevaporationrate,Flashpoint>23οC.AvailablePackaging5Land20Lmetalcanisters.NOTES AND PRECAUTIONS: Storage of closed containers, in controlled dry and enclosed space,away from sources of ignition and temperatures from 5οC to 35οC, for up to 18 months. TheTechnical Data should be read in conjunction with the Safety Data Sheets and Coating TechnicalSpecification. This product is for professional use only. For more information please contactNanoPhos:[email protected]@NanoPhos-Marine.com

48

TECHNICALDATA

GENERALNOTICEPlease observe the precautionary notices displayed on the container of eachproduct.Useunderwellventilatedconditions.Donotbreatheorinhalemist.Avoidskin contact. Spillage on the skin should immediately be removed with suitablecleanser, soar and water. Eyes should be well flushed with water and medicalattention sought immediately. Always ask, read and comprehend health or safetyhazardsandprecautionsforuseofeachproduct,asdescribedintherelevantSafetyDataSheet.LIMITEDWARRANTYINFORMATION-PLEASEREADCAREFULLYThe information contained herein is offered in good faith and is believed to beaccurate. However, because conditions and methods of use of our products arebeyond our control, this information should not be used in substitution forcustomer’s tests to ensure that NanoPhos’ products are safe, effective and fullysatisfactory for intended end use. Suggestions of use shall not be taken asinducements to infringe any patent. NanoPhos specifically disclaims any otherexpressedorimpliedwarrantyoffitnessforaparticularpurposeormerchantability.NanoPhos disclaims liability for any incidental or consequential damages. Theaforementionedproductsareneithertestednorrepresentedassuitableformedicalor pharmaceutical uses. NanoPhos reserves the right to change the given datawithout any prior notice.Minor product variations may be implanted in order tocomplywithlocalrequirements.Ifthereisanyinconsistencyinthetext,theEnglishVersionwillprevail.

Version-011216,December2016

49

NanoPhosS.A.POBOX519Science&TechnologyParkofLavrioLavrio,Greece,19500 Tel:(+30)2292069312Fax:(+30)[email protected] [email protected] www.NanoPhos-Marine.com

Documents

TECHNICAL DATA BOOK OF INDUSTRIAL COATINGSnanophos.pk/downloads/4. NanoPhos Industrial... · TECHNICAL DATA BOOK OF INDUSTRIAL COATINGS 2 MAINTENANCE, REPAIRS AND CLEANING HMD Heavy