Embed Size (px)
DESCRIPTION
Switch Parameters
Citation preview
1/ CS_HHO_ASYNC_CTRL_SWITCH (Asynchronous Reconfigure Switch for CS HHO)
When this switch is turned on, the RNC does not put the activation time information element (IE) in the hard handover configuration message for CS services. After receiving the message, the UE immediately activates the configuration.
When this switch is turned off, the RNC puts the activation time IE in the hard handover configuration message for CS services. After receiving the message, the UE activates the configuration at the specified activation time.
2/ PS_HHO_ASYNC_CTRL_SWITCH (Asynchronous Reconfigure Switch for PS HHO)
When this switch is turned on, the RNC does not put the activation time information element (IE) in the hard handover configuration message for PS services. After receiving the message, the UE immediately activates the configuration.
When this switch is turned off, the RNC puts the activation time IE in the hard handover configuration message for PS services. After receiving the message, the UE activates the configuration at the specified activation time.
SET URRCTRLSWITCH: PROCESSSWITCH4=PHY_RECFG_REEST_SWITCH-1&PHYCHRECFG_ENH_RL_REEST_SWITCH-1;
SET URRCTRLSWITCH: PROCESSSWITCH2=CELLUPT_RLFAILURE_SRBREESTAB_SWITCH-1, PROCESSSWITCH4=RB_SETUP_RL_REEST_SWITCH-1&RB_SETUP_ENHANCE_RL_REEST_SWITCH-1;
SET URRCTRLSWITCH: PROCESSSWITCH4=RBRECFG_ENH_RL_REEST_SWITCH-1, Optimization Switch=RB_RECFG_RL_REEST_SWITCH-1, Improvement Switch=NON_DCCC_RBRECFG_RL_REEST_SWITCH-1;
SET URRCTRLSWITCH: PROCESSSWITCH4=IRATHO_HOCANCEL_RL_REEST_SWITCH-1;
SET URRCTRLSWITCH: OptimizationSwitch4=RB_RLREEST_AM_TRB_RLC_REEST_SWITCH-1&RB_SETUP_UM_TRB_RLREEST_ADJUD_OPT_SWITCH-1;
SET UCONNMODETIMER: T302=D1400, N302=3, T313=3, N313=D20, T314=D12,T315=D10, N315=D20;
Command for 3RA06
Process switch = INVOKE_TRACE_SWITCH::OFF
= SYS_INFO_UPDATE_FOR_IU_RST::OFF
= DRNC_DIRECT_DSCR::ON
= PTUSER_IDENTIFY_ENH_SWITCH::OFF
= RNC_SHARE_SWITCH::ON
= RNCAP_IMSI_HO_SWITCH::OFF
= TERMINAL_VERSION_DEBASE_SWITCH::OFF
= SYS_HO_OUT_CIPHER_SWITCH::OFF
= SYS_HO_CIPHER_CONFIG::ON
= BARRED_CELL_FOR_CSDOMAIN_RST::OFF
= CR2284R1_SWITCH::OFF
= CDT_MSG_FULL_TRACE::ON
= CR2284R1_COMPATIBLE_SWITCH::ON
= COMBINE_OPERATION_DRD_SWITCH::ON
= UL_INTER_PROTECT_SWITCH::OFF
= FAST_DORMANCY_SWITCH::ON
= SYS_HO_IN_CIPHER_SWITCH::OFF
= PTT_EARLY_TRANS_SWITCH_OFF::OFF
= UPLINK_MDC_ENHENCEMENT_SWITCH::OFF
= NODEB_PRIVATE_INTERFACE_SWITCH::ON
= PTT_SPEC_LI_SWITCH_OFF::OFF
= RNC_DF_2_URA_PCH_SWITCH::OFF
= FD_TAC_MATCH_SWITCH::OFF
= NONPTT_L1_FAST_SYNC_SWITCH::OFF
= URAPCH_LAYERED_PAGING_RT_SWITCH::OFF
= URAPCH_LAYERED_PAGING_NRT_SWITCH::OFF
= IDLE_LAYERED_PAGING_NRT_SWITCH::OFF
= IDLE_LAYERED_PAGING_RT_SWITCH::OFF
= INTELLIGENT_WIFI_DETECT_AND_SELECTION::OFF
= INTERRAT_LOAD_REPORT_FOR_LTE_SWITCH::OFF
= PTUSER_IDENTIFY_SWITCH::OFF
Process Control Switch 2 = LOAD_IRAT_HO_RNC_FILL_TL::OFF
= SEND_IDT_JUDGE_IU_RESET::OFF
= RNC_RBRECFG_DRD_FAIL_ROLLBACK_SWITCH::ON
= RNC_CS_QUERY_UE_IMEI_SWITCH::OFF
= RNC_PS_QUERY_UE_IMEI_SWITCH::ON
= FACH_DTCH_CONGEST_P2D::OFF
= RNC_RBSETUP_DRD_FAIL_ROLLBACK_SWITCH::ON
= PS_NOTIFYCN_NOTDOWNSIZE_SWITCH::OFF
= ASU_RSP_TIMEOUT_HANDLE_SWITCH::OFF
= RB_RECFG_USER_INACT_SWITCH::OFF
= RRC_SCRI_NORM_REL_SWITCH::OFF
= CELLUPT_RLFAILURE_SRBREESTAB_SWITCH::OFF
= CU_OVERLAP_DSCR_SWITCH::OFF
= TRB_RST_DSCR_SWITCH::OFF
= RNC_FD_SCRI_FORCE_REL_SWITCH::ON
= USRPLN_PRORATION_SHARED_ALO::OFF
= FP_IUUP_TRACE_SWITCH::ON
= RNC_PCHR_OUTPUT_CTRL_SWITCH::OFF
= DTMF_SWITCH::ON
= FAST_CS_FB_BASEDON_RIM_SWITCH::ON
= L2U_SRVCC_WITH_PS_HO_SWITCH::OFF
= ULTRA_FLASH_CSFB_SWITCH::OFF
= RNC_PS_QUERY_UE_IMEISV_SWITCH::OFF
Process Control Switch 3 = FACH_DCCH_CONG_CTRL_SWITCH::OFF
= RNC_F2D_RLC_SUSPEND_SWITCH::ON
= UM_RRCRELCMP_RLDEL_DELAY_SWITCH::OFF
= RNC_TVM_BASED_P2D_SWITCH::ON
= CS_RLFAIL_RRCSETUP_STAT_SWITCH::OFF
= PS_INACT_NOTREL_FOR_CSPS_SWITCH::OFF
= RAB_DL_BITRATE_MOD_SWITCH::ON
= RAB_WAIT_IUUP_INIT_RESPONSE_SWITCH::OFF
= CS_CALL_DROP_DEFINITION::OFF
= PS_CALL_DROP_DEFINITION::OFF
= CCH_ABNORMOLREL_CAUSE_SWITCH::OFF
= RNC_U2U_SWITCH::OFF
= INTERRAT2U_RESUME_PS_ASAP_SWITCH::OFF
= UE_TRB_RESET_IOT_SWITCH::OFF
= CUC_CMP_NO_ACTIVE_CFN_SWITCH::OFF
= RNC_RDY_FOR_INTERRAT_COMPATIBLE_SWITCH::OFF
Process Control Switch 4 = PS_F2D_OVERLAP_CELLUPT_SWITCH::OFF
= AMR_HHO_FAIL_ROLLBACK_SWITCH::OFF
= PHY_RECFG_REEST_SWITCH::OFF
= IUR_RL_REEST_SWITCH::OFF
= RB_SETUP_RL_REEST_SWITCH::OFF
= RRC_CONN_SETUP_OPT_SWITCH::OFF
= TCP_ACK_ACCELERATOR_SWITCH::OFF
= RRC_CELLFACH_TRB_RESET_TO_F2D_SWITCH::OFF
= SEND_MSG_NULL_SWITCH::OFF
= FD_PCH_IUR_CS_OPT_SWITCH::OFF
= CELLUPT_T314_T315_TIMEOUT_OPT_SWITCH::OFF
= CS_HHO_ASYNC_CTRL_SWITCH::OFF
= PS_HHO_ASYNC_CTRL_SWITCH::OFF
= IUR_HHO_ASYNC_CTRL_SWITCH::OFF
= R8_UE_SEL_DPUE_SWITCH::OFF
= F2P_DATATRANS_OPTIMIZE_SWITCH::OFF
= IRATHO_HOCANCEL_RL_REEST_SWITCH::OFF
= TRB_RESET_RL_REEST_SWITCH::OFF
= RB_REL_RL_REEST_SWITCH::ON
= RB_SETUP_ENHANCE_RL_REEST_SWITCH::OFF
= RAB_SETUPMOD_CNT_FIX_SWITCH::OFF
= PCH_UE_RLC_UNRECOVERABLEERROR_SWITCH::OFF
= FAST_RETURN_LTE_BY_CELL_SELECT_SWITCH::OFF
= UL_DUAL_MODE_UE_D2P_OR_D2I_SWITCH::OFF
= PHYCHRECFG_ENH_RL_REEST_SWITCH::OFF
= RBRECFG_ENH_RL_REEST_SWITCH::OFF
= SMC_STOP_RLC_SWITCH::ON
= GTP_SN_IN_RAB_REL_INIT_BY_UTRAN_SWITCH::OFF
= CMP_IU_QOS_GTP_PDU_SN_SWITCH::OFF
= DL_TRB_RESET_BUFF_SWITCH::OFF
= RRC_CELLFACH_DL_TRB_RESET_TO_F2D_SWITCH::ON
= RAB_ASS_MOD_TNL_ADDR_SUP_SWITCH::ON
Process Control Switch 5 = INTERRAT_LOAD_SINGLE_RPT_FOR_LTE_SWITCH::OFF
= INTERRAT_LOAD_REPORT_FROM_LTE_SWITCH::OFF
= UL_EVQI_SWITCH::OFF
= DL_EVQI_SWITCH::OFF
= VIDEO_RATE_ADAPTION_SWITCH::OFF
= VOIP_MANAGE_SWITCH::OFF
= DIFF_SERVICE_ON_TERMINAL_SWITCH::OFF
= APP_GRP_RES_RSV_SWITCH::ON
= RIM_ON_ECO_SWITCH::OFF
= SRBCHG_DRD_FAST_RB_SETUP_SWITCH::OFF
= SRBNOCHG_DRD_FAST_RB_SETUP_SWITCH::OFF
= FACH_RB_RECFG_FAIL_SPEC_CAUSE_SWITCH::OFF
= WBAMR_HHO_FAIL_ROLLBACK_SWITCH::OFF
Iub Private Interface Switch = RL_OpIndex_INCLUDED::OFF
= PSCRR_OpIndex_INCLUDED::OFF
Optimization Switch = PAGGING_NUM_CTRL_SWITCH::OFF
= ASU_RL_RESET_SWITCH::ON
= MC_RL_RESET_SWITCH::ON
= FD_PCH_REENTERSA_FORCE_RRC_REL_SWITCH::OFF
= UE_CRC_COMPATIBLE_SWITCH::OFF
= RNC_P2D_DRD_SWITCH::OFF
= P2D_SWITCH::ON
= AMR_F2D_OVERLAP_CELLUPT_SWITCH::ON
= SRB_RESET_RL_SETUP_SWITCH::ON
= RLFAIL_RL_SETUP_SWITCH::ON
= CS_RL_SETUP_SWITCH::ON
= PS_RL_SETUP_SWITCH::ON
= UE_SRB_RESET_SWITCH::ON
= RL_RESTORE_SWITCH::OFF
= RNC_EFD_D2F_SWITCH::ON
= RNC_RB_SCRI_NOT_DROP_SWITCH::OFF
= RRC_RECONN_SWITCH::OFF
= RRC_REPEAT_PFM_SWITCH::ON
= F2D_NO_RSP_RRCREL_SWITCH::OFF
= CS_SETUP_P2D_SWITCH::ON
= SYSHO_CIPHER_IE_SWITCH::OFF
= P2P_GTPU_NOT_CFG_SWITCH::OFF
= RB_SETUP_CIPHER_TIME_ADJ_SWITCH::OFF
= CS_PRI_MOD_NOT_INT_SWITCH::OFF
= RAB_SETUP_TMSI_REALLOC_BUF_SWITCH::OFF
= IU_FAULT_REL_PS_RES_SWITCH::OFF
= RB_RECFG_RL_REEST_SWITCH::OFF
= F2P_DT_MSG_BUFFER_SWITCH::OFF
= SCRI_COMPATIBLE_SWITCH::OFF
= GTPU_ERR_IND_DEF_SWITCH::OFF
= IUR_SRV_CELL_CHG_MACHS_RESET_SWITCH::OFF
= UL_INTEG_ALGO_COMPAT_SWITCH::OFF
Optimization Switch2 = DRNC_DCH_RCV_CELL_RESEL_MSG_DSCR_SWITCH::OFF
= MULTIRAB_ATTESTAB_DEF_SWITCH::OFF
= PCH_UE_SRB_RESET_DSCR_SWITCH::OFF
= DRNC_CELL_CODE_CONFLICT_OPT_SWITCH::OFF
= RAB_FAIL_CAUSE_SWITCH::OFF
= PSPS_SETUP_REL_DEF_SWITCH::OFF
= RRC_CON_REQ_TIMES_COMPATIBLE_SWITCH::OFF
= SECU_CU_CROSS_SWITCH::OFF
= HHO_CNT_CORRECT_SWITCH::OFF
= IRATHO_CNT_CORRECT_SWITCH::OFF
= RB_CU_CROSS_COMPATIBLE_SWITCH::OFF
= RNTI_ENH_ALLOC_AlGO_SWITCH::OFF
= DRNC_LOAD_CTRL_SWITCH::ON
= EFACH_CU_COMMON_HRNTI_SWITCH::ON
= PSCS_CALLDROP_FIX_SWITCH::ON
= CSABNREL_DUETO_PSREL_FIX_SWITCH::ON
Function Switch = RRC_CONN_STATE_TO_NODEB_SWITCH::ON
= CS_SECMODE_PRI_CSPS_SWITCH::ON
= AMR_SILENT_DETECT_SWITCH::ON
= IU_FLEX_CONG_DISCARD_SWITCH::OFF
= UL_INTEG_ALGO_FOR_CELLUPDATE_SWITCH::OFF
= AMRWB_SILENT_DETECT_SWITCH::OFF
Maximum Paging Times for UEs in CELL_PCH = 5
Maximum Paging Times for UEs in URA_PCH = 5
Optimization Switch3 = SYS_RELOC_OUT_SUCC_STAT_OPT_SWITCH::OFF
= RL_REEST_PS_ON_FACH_SWITCH::OFF
= CELLUPDATE_MEASUREMENT_OPT_SWITCH::OFF
= D2F_PROCEDURE_OPTIMIZATION_SWITCH::OFF
= F2D_PROCEDURE_OPTIMIZATION_SWITCH::OFF
= FOREVER_PCH_CTRL_PLANE_SHARE_OPT::OFF
= FOREVER_PCH_USER_PLANE_SHARE_OPT::OFF
= RAB_REL_SRV_CELL_CHG_CROSS_SWITCH::OFF
= SCRIWITHCAUSE_OVERLAP_SWITCH::OFF
= P2F_CUC_REPEAT_SWITCH::OFF
= UU_ABN_REL_INFO_NOTIFY_NODEB_SWITCH::OFF
= D2F_AM_PROCEDURE_OPTIMIZATION_SWITCH::OFF
= AM_D2F_F2D_RESTMR_OPTIMIZATION_SWITCH::OFF
= D2P_DT_MSG_BUFFER_SWITCH::OFF
= CM_CODE_CONFLICT_OPT_SWITCH::OFF
= H_SERV_CELL_CHANGE_MSG_OPT_SWITCH::OFF
= FAST_HSDPA_SERV_CELL_CHANGE_SWITCH::OFF
= RLRST_ASU_SUCC_COUNTERS_CORRECT_SWITCH::OFF
= COUNT_STATE_CHG_BY_RAB_EHN_SWITCH::OFF
= RAB_RELATED_COUNTER_OPT_SWITCH::OFF
= CELLUPDATE_PROCEDURE_OPT_SWITCH::OFF
= PTT_PAGING_PRD_CRRCT_SWITCH::OFF
= RRC_REL_STATUS_RSP_RAB_ASS_REQ_SWITCH::OFF
= L2U_UP_DELAY_OPT_SWITCH::ON
= PRI_LDR_SYSHO_OUT_USE_SELECT_OPT_SWITCH::OFF
Rate of NBAMR UEs with Noise Detection in the DL = 0
Rate of WBAMR UEs with Noise Detection in the DL = 0
Improvement Switch = CONVERT_RELOC_FAIL_CAUSE_SWITCH::OFF
= DEAL_SRNS_CONTEXT_REQ_FIRST_SWITCH::OFF
= DELAY_DRNC_CODE_REL_SWITCH::OFF
= ROUT_IDT_BY_ROUTING_PARA_SWITCH::OFF
= COUNT_CS_REC_IU_REL_CMD_SWITCH::OFF
= SEND_UE_CAP_ENQ_RELOC_CCH_SWITCH::ON
= REL_IUR_CCH_BEFORE_DSCR_SWITCH::OFF
= RELOC_CIPHER_PENDING_COMPATI_SWITCH::OFF
= COUNT_SPECIAL_RAB_ATT_SWITCH::OFF
= COUNT_STATE_CHG_BY_RAB_SWITCH::OFF
= DELAY_SEND_MEACTRL_SWITCH::OFF
= TAKE_ACTIVE_TIME_DRD_SWITCH::OFF
= CS_DISCONNECT_OPT_SWITCH::OFF
= NON_DCCC_RBRECFG_RL_REEST_SWITCH::OFF
= SMC_RL_REEST_SWITCH::OFF
= PSHO_CSFB_UE_CAP_ENQ_DELAY_SWITCH::OFF
= PAGING_OM_OPTIMIZE_SWITCH::OFF
= DEACTIVE_CELLHSPA_H2F_SWITCH::OFF
= OMIT_UE_CAP_ENQ_RELOC_DCH_SWITCH::OFF
= RAB_SETUP_CNT_CORRECT_SWITCH::ON
= FACH_DCCH_RRC_REL_NO_RSP_DELAY_USE_URNTI::ON
= FACH_CCCH_RRC_REL_NO_RSP_DELAY_USE_URNTI::OFF
= DCH_DISCARD_CELL_RESEL_CU_MSG_SWITCH::OFF
= SYS_INIT_SPU_STATE_BROADCAST_OPT_SWITCH::ON
= RB_RECFG_F2D_ISR_IC_FAIL_RRC_REL_SWITCH::OFF
= PTT_RAB_SETUP_ATT_CNT_CORRECT_SWITCH::OFF
= P2D_DRD_FAIL_BACK_RESEL_CELL_SWITCH::OFF
= TRB_RST_CU_NOT_REEST_UM_RLC_TRB_SWITCH::OFF
= ONE_CNNODE_SCCP_CONG_SEL_OTHER_SWITCH::OFF
= CSFB_UE_DELAY_RAU_SWITCH::OFF
= CSFB_UE_CS_IMEI_QUERY_DISABLE_SWITCH::OFF
Paging Type 1 Resending Times for PCH UE Release = 3
Optimization Switch4 = RB_RLREEST_AM_TRB_RLC_REEST_SWITCH::OFF
= RB_SETUP_UM_TRB_RLREEST_ADJUD_OPT_SWITCH::OFF
= DRNC_RL_REEST_OPT_SWITCH::OFF
= URA2FACH_OVERLAP_CELLUPT_PROC_SWITCH::OFF
= RB_SETUP_F2D_USE_AM_RLC_SWITCH::ON
= RB_RECFG_D2F_USE_AM_RLC_SWITCH::OFF
= RB_RECFG_F2D_USE_AM_RLC_SWITCH::ON
= RRC_UE_USER_SMOOTH_OPT_SWITCH::OFF
= TRNC_LOAD_CTRL_SWITCH::OFF
= IU_SIG_REL_PCH_PAGING_SWITCH::OFF
= CPC_OPT_FOR_RLSETUP_SWITCH::ON
= D2P_L2DEACT_FAIL_OPT_SWITCH::OFF
= EFACH_RRC_REG_CMP_SWITCH::OFF
= P2D_TSID_ERR_UE_RSP_MSG_DISCD_SWITCH::OFF
= AMRC_ON_122_AMR_HHO_ROLL_BACK_SWITCH::OFF
= RELOC_IN_RG_COMB_INDEX_ALLOC_SWITCH::OFF
= SCM_CU_CROSS_SWITCH::OFF
= DRNC_HSPA_CM_OPT_SWITCH::OFF
= IUB_TRANSID_OPT_SWITCH::OFF
= L2_ENHENCE_RECFG_OPT_SWITCH::OFF
= ASYN_RL_REEST_OPT_SWITCH::OFF
= RNC_IMSI_HO_OPT_SWITCH::OFF
= IUR_PRIQUEUE_INFO_TO_MODIFY_OPT_SWITCH::OFF
= URA_PCH_LAC_RAC_CHG_NO_PAGING_SWITCH::OFF
= PAGING_OVERLAP_CU_OPT_SWITCH::OFF
= SRVCC_RELOC_IN_USE_CS_KEY_SWITCH::ON
= SOCKET_RECEIVE_DATA_CORRECT_SWITCH::OFF
= CU_PRI_OVERLAP_OTHER_PROC_SWITCH::OFF
= INTERRAT2U_INTEG_PROTECT_OPT_SWITCH::OFF
= INTRA_NODEB_RLCC_INIT_CAP_OPT_SWITCH::OFF
= DRNC_RL_PARA_UPT_OPT_SWITCH::ON
Relative Threshold for Allocating R8 UEs to DPUe = 5
Optimization Switch5 = U2L_RELOC_MSG_TAKE_ERAB_SWITCH::OFF
= PS_DOMAIN_REL_RAB_SETUP_SWITCH::OFF
= PCH2FACH_PS_TRAFFIC_PFM_FIX_SWITCH::OFF
= GSM_SYS_HO_IN_NO_UE_CAP_ENQ_SWITCH::OFF
= D2P_TWO_SIDE_RLC_REEST_SWITCH::OFF
= D2F_SRNS_CONTEXT_REQ_OPT_SWITCH::OFF
= DL_SIG_TRS_REQ_REL_UE_PRO_SWITCH::ON
= DSP_CAP_JUDGE_SWITCH::ON
= MPU_FC_USER_PLN_RSR_CHK_SWITCH::ON
= RB_CU_FAIL_RRC_REL_CELL_OPT_SWITCH::ON
= RB_RFG_MSG_USE_NEW_SG_SWITCH::OFF
= SRB3_SRB4_RLC_RST_RRC_REL_SWITCH::OFF
= WEAK_COV_NO_EXT_CS_RAB_SET_ACT_TM_SWITCH::OFF
= PS_0K_STATIC_RELOC_IN_CMP_SWITCH::OFF
= ADD_DRL_PS_0K_TO_8K_SWITCH::OFF
= CU_AL_RES_OPT_SWITCH::OFF
= DRNC_SERV_CELL_CHG_BUGFIX_SWITCH::OFF
= TRNC_TPC_INDEX_ALLOC_SWITCH::OFF
= IUR_ATM_TRAN_OPT_SWITCH::OFF
= RELOC_REQ_CIPHER_COMP_SWITCH::OFF
= STATIC_RELOC_FAIL_DRNC_CLR_RSR_SWITCH::OFF
= RNC_IN_POOL_IU_RESET_SWITCH::ON
= USE_EFD_WITHOUT_EFD_OFF_TAC_SWITCH::OFF
= RAB_MOD_IUPS_ADMIFAIL_GTPU_REEST_SWITCH::OFF
= PS_U2L_USER_PLANE_DELAY_OPT_SWITCH::OFF
= P2F_CU_CAUSE_CHG_OPT_SWITCH::OFF
= P2F_REDIRECT_CELLUPDT_RESEND_OPT_SWITCH::OFF
= RELOC_IN_PROCESS_OPT_SWITCH::OFF
= CU_ROUT_OPT_SWITCH::OFF
DPUe to DPUb Processing Capability Ratio = 200
UL Integrity Protection Fail Tolerance Times = 3
Optimization Switch6 = ASU_RSP_FAIL_REL_UE::OFF
= CELL_PCH_UES_OPT_SWITCH::OFF
= DRNC_NOTICE_NODEB_SRNC_VEST_SWITCH::OFF
(Number of results = 1)
%%/*4837494*/LST UCONNMODETIMER:;%%
RETCODE = 0 Execution succeeded.
List UE Timers and Constants in Connected Mode
----------------------------------------------
Timer 302 = D2000
Constant 302 = 3
Timer 304 = D2000
Constant 304 = 3
Timer 305 = D30
Timer 307 = D30
Timer 308 = D40
Constant 308 = 1
Timer 309 = 5
Timer 312 = 6
Constant 312 = D1
Timer 313 = 3
Constant 313 = D50
Timer 314 = D12
Timer 315 = D30
Constant 315 = D1
Timer 316 = D30
Timer 381 = D600
Constant 381 = D1
Timer 323 = D0
(Number of results = 1
