Embed Size (px)
Citation preview
L S
D sseleri
WEthernet
1 2 3 4 1enohP
2enohP
tenret
nI
rewoP
Wireless on / off
4 32 1
Reset
1 2 < >...
Off / OnO / l
DSL
> Nur auf Anweisung von Swisscom entfernen.> Ôter uniquement sur instructions de Swisscom.> Rimuovere solo su instruzione di Swisscom.> Only remove when instructed by Swisscom 84 3
2 1
Reset
1 2 < >...
Off / OnO / l
DSL
> Nur auf Anweisung von Swisscom entfernen.> Ôter uniquement sur instructions de Swisscom.> Rimuovere solo su instruzione di Swisscom.> Only remove when instructed by Swisscom
4 32 1
Reset
1 2 < >...
Off / OnO / l
DSL
> Nur auf Anweisung von Swisscom entfernen.> Ôter uniquement sur instructions de Swisscom.> Rimuovere solo su instruzione di Swisscom.> Only remove when instructed by Swisscom
1
4
7
R
2
5
8
0
3
6
9
Modem
Note for 4-pole telephone sockets: Connect themicrofi lter using an adapter (available from any Swisscom shop). Do not plug telephones or fax ma-chines into the second connection of the adapter.
4-pole telephone socket
Adapter
Microfi lter
1 Do not begin the installation of the newmodem until after the connection date. You have been notifi ed of this by letter.
2 If you > Already possessed a fast Internet connec-
tion (ADSL, DSL or similar), proceed with Step 3.
> Did not previously possess a fast Internet connection, go directly to Step 4.
3 Remove> The old modem> The old power supply unit (if present)> The old modem cable (violet)> And all old microfi lters
You can return the old units to any Swisscom shop.
4 Switch your computer off .
5 Unplug all telephones.
6 Choose the telephone socket to which you wish to connect your modem.
Observe the following points: If you
> Wish to use Bluewin TV, position themodem by the telephone socket closest to your television.
> Do not wish to use Bluewin TV, position the modem by the telephone socket clos-est to your computer.
7 Connect the units and cables supplied as shown in the illustration on the right.
1. Preparations 2. Connecting units and cables1.1 Checking contents 1.2 Preparing for set-up
Modem (WLAN router) with power supply unit
Ethernet cable (yellow)
Modem cable (violet)
Manuals
2 microfi lters (with Swisscom logo)
The package includes:
SAP 127489 06/09
8 First switch the modem on and then the computer.
9 Wait until at least the following lamps light up on the modem:> «Power»> «Ethernet»
(one of the four lamps)> «Wireless»> «DSL»
L S
D sseleriWEthernet
1 2 3 4 1enohP
2enohP
tenretnI
rewoP
Wireless on / off
Note: You need a microfi lter (with the Swisscom logo) for every telephone in your home.
Mod
em c
able
(vio
let)
Power supply unit
Telephone
Ethernet cable (yellow)
Computer
Note: The telephone sockets can diff er in appearance.
Telephone sockets
Microfi lters
Telephone cable Note: In the event of problems, please refer to the «Troubleshooting» section on the back of this manual.
10 Check whether your telephone is work-ing. Can you hear a dialling tone?
Note: In the event of problems, please refer to the «Troubleshooting» section on the back of this manual.
11 If you > Are a new Swisscom DSL customer
you still need to enable your Inter-net connection (registration). Follow Section «3. Registering DSL by Swiss-com» on the back of this manual.
> Are an existing Swisscom DSLcustomer (DSL customer or Bluewin TV customer), you can now> use the Internet> install Bluewin TV or > set up WLAN in accordance with
the attached manual «Setup WLAN».
WLAN router
analogue
Setting up Internet
Swisscom (Switzerland) AGHardturmstrasse 3PO Box 756CH-8037 Zurich
Freephone number: 0800 800 800www.swisscom.ch
For new Swisscom DSL customers only: 3. Registering DSL by Swisscom1 Start your browser (Internet Explorer , Firefox , Safari , etc.).
2 The DSL registration page appears automatically in your browser. You will be guid-ed through the registration process step by step. Complete all compulsory fi elds.
If a progress bar is displayed, wait until this process has fi nished and then continue with registration.
Note: If neither the registration page nor a progress bar is displayed, access the registra-tion page by entering «www.swisscom.ch» in the address fi eld of your browser and press-ing the Enter key .
Then continue with the registration.
Troubleshooting> Is the «Power» lamp lit on the modem?
No > Check whether your modem is switched on (Step 8). No > Check the power supply unit and mains connection (Step 7).
> Is the «DSL» lamp lit on the modem?
No > The DSL line is faulty or not yet connected.> Check the cabling between the modem and telephone socket (violet cable).> Check the connection date for the DSL connection in one of the letters you have
received from Swisscom.
> Is at least one «Ethernet» lamp lit on the modem?
No > Check whether your computer is switched on (Step 8). No > Check whether your computer is correctly connected to the modem (Step 7).
> Have you used a white microfi lter (with Swisscom logo) for every telephone in your home?
No > Use a white microfi lter (with Swisscom logo) for every telephone.
> Are you using the modem cable (violet) supplied? No > Use the cable supplied.
> Is your Internet access now working? No > Contact us on the freephone number 0800 800 800.
Note: If you run into problems during set-up that you cannot resolve even using these instructions, please contact the freephone number 0800 800 800.
3 At the end of the registration process, print out the datasheet and enter your Swisscom login data here:
Username: __________________________ Password: ___________________________
4 After registration, you can set up a wireless Internet connection (WLAN) on your com-puter. To do this, follow the instructions on the screen or the attached manual «Setup WLAN».
L S
D sseleriWEthernet
1 2 3 4 1enohP
2enohP
tenretnI
rewoP
Wireless on / off
L S
D sseleriWEthernet
1 2 3 4 1enohP
2enohP
tenretnI
L S
D sseleriWEthernet
1 2 3 4 1enohP
2enohP
tenretnI
rewoP
Wireless on / off
tenretnI
sseleriWEthernet
1 2 3 4 1enohP
2enohP
rewoPP
L S
D sseleriWEthernet
1 2 3 4 1enohP
2enohP
tenretnI
rewoP
Wireless on / off
L S
D sseleriW
1enohP
2enohP
tenretnI
rewoPP
