Embed Size (px)
Citation preview
SECTIONDATE
SUPERSEDES
TITLE
CT310KX
-04-16-14A
01-21-14
TABLE OF CONTENTS
20923
SECTION 100 DESCRIPTION & SPECIFICATIONS20553 INTRODUCTION & LIMITS OF USE23054 LOAD CAPACITY CHART20568 CONTROL PENDANT & OVERLOAD SENSING SYSTEM20569 TRUCK SET-UP, SWIVEL LOAD BLOCK USE, & PREPARATION FOR TRAVEL20729 TWO PART LINE CONFIGURATION
SECTION 150 SAFETY - GENERAL20556 CRANE SAFETY20557 ELECTROCUTION HAZARD, CRANE SAFETY NEAR POWER LINES, & MINIMUM CLEARANCE20558 SAFETY WARNINGS - AN EXPLANATION20559 ELECTROCUTION HAZARD DECALS20560 SAFETY SIGNS & DECALS21353 SAFETY DECALS (PAGE 1 OF 2)21384 SAFETY DECALS (PAGE 2 OF 2)21377 DECAL DRAWINGS & LIST (PAGE 1 OF 2)21378 DECAL DRAWINGS & LIST (PAGE 2 OF 2)
SECTION 200 INSTALLATION INSTRUCTIONS20563 INSTALLATION PROCEDURE20564 INSTALLATION DIMENSIONS DRAWING20714 BASE MOUNTING DIMENSIONS20565 BATTERY CABLE INSTALLATION DRAWING20566 FINAL PREPARATION PRIOR TO USE
SECTION 300 MAINTENANCE AND SERVICE20571 PREVENTATIVE MAINTENANCE OVERVIEW & PERIODIC INSPECTION SCHEDULE21982 LUBRICATION SCHEDULE20573 MINIMUM VOLTAGE TEST20574 WIRE ROPE INSTALLATION & REPLACEMENT20575 HYDRAULIC SYSTEM SCHEMATIC
SECTION 400 REPLACEMENT PARTS20851 REPLACEMENT PARTS ILLUSTRATION20852 REPLACEMENT PARTS LIST20924 HYDRAULIC SYSTEM PARTS DRAWING20925 HYDRAULIC SYSTEM PARTS LIST21027 ELECTRICAL SYSTEM PARTS DRAWING21584i SWIVEL TERMINAL ASSY. REPL. PARTS ILLUSTRATION20837 WINCH REPLACEMENT PARTS LIST27041 SLEW DRIVE REPLACEMENT PARTS20582 PENDANT (4 SWITCH) PARTS DRAWING20583 PENDANT (4 SWITCH) PARTS LIST20561 DECAL PLACEMENT20585 FIELD SERVICE LABEL KIT LIST
TABLE OF CONTENTSVENTURO CT310KX OWNER'S MANUAL
®VENCO VENTURO INDUSTRIES LLC
CINCINNATI, OHIO
SECTION 100
DESCRIPTION
&
SPECIFICATIONS
7607100A
SECTIONDATE
SUPERSEDES
TITLE
CT310KX
C10010-24-13B
08-12-13A
INTRODUCTION & LIMITS
20553
®MANUFACTURING, INC.
CINCINNATI, OHIO
NOTESINTRODUCTIONThis manual is prepared for the truck mounted crane Model CT310KX.
The CT310KX crane is an electric / hydraulic powered, continuous rotation
unit manufactured by Venco Venturo Industries LLC of Cincinnati, Ohio.
The boom on this crane extends 32 inches hydraulically with an additional
32 inch manual extension. In the retracted position, the boom is 4 12 feet
long. When fully extended, the boom is 9 12 feet long.
ABOUT THIS MANUALThe sections included in this manual are:
Descriptions & Specifications
The introduction section provides an overview of the use of the crane.
Safety
Safe operating and maintenance procedures are introduced in this
section. Also included is an explanation of the safety warnings and
signs used on the crane.
Installation Instructions
The installation section provides instructions for installing the crane on
your truck.
Maintenance & Service
Preventive maintenance inspections and crane lubrication schedules
are listed in this section. Replacement and adjustment procedures are
provided.
Replacement Parts
Replacement part numbers and ordering procedures are provided in
this section.
LIMITS OF USEThe CT310KX crane is designed to lift loads up to the limits as shown
on the capacity chart (DWG. 23054).
D Lifting of personnel is NEVER permitted.
D Lifting loads exceeding the capacity chart (DWG. 23054) voids
the warranty agreement.
CT310KX DESCRIPTION & SPECIFICATIONS
SECTIONDATE
SUPERSEDES
TITLE
VENTURO CT310KX
C10010-29-13
-
LOAD CAPACITY CHART
23054
®MANUFACTURING, INC.
CINCINNATI, OHIO
2
REACH (FT)HORIZONTAL
VE
RT
ICA
LH
EIG
HT
(FT
)
5
4
3
8 10976543
-1
-2
-3
-4
0
1
210-5
6
7
8
9
11
12
13
14
10
30°
45°
60°
-15°
-30°
-45°
-60°
Weight of load handling devices are part of the load and must be deducted from the gross capacity.
LOAD BLOCK USAGE1-Part line for loads less than 1000 lbs.
2-Part line for loads of 1000 lbs. and greater.Weight of Load Block = 5.2 lbs.
75511001750
900
1250
1850
1000
1250
1900
1000
1250
1900
1000
1250
1900
750
1050
1700
1650
1000
700
650
950
1625
1915
950
650
CT310KX MAXIMUM CAPACITY CHART
15°
0°
SECTIONDATE
SUPERSEDES
TITLE
CT310KX
C10008-12-13A
11-04-02
PNDNT & OVRLD SNSNG
20568
R
MANUFACTURING, INC.
CINCINNATI, OHIO
CT310KX DESCRIPTIONS & SPECIFICATIONS
UP
UP
DOWN
DOWNOUT
IN
W
I
NCH
B
OOM
ROTATION
L R
CONTROL PENDANTThe control pendant is attached to the crane assembly with a 20 foot cord
assembly. This plug-in cord allows for operation in all points of the crane's
reach. The cord is to be removed and stored when the crane is not in use.
Cane Operation Controls - Toggle SwitchesThese switches are spring loaded to the center position (or the OFF
position). By pressing the switch to the desired direction, the operation will
be activated. When the switch is released, it will return to the center (OFF)
position and the operation will stop.
WINCH (Up / Down)
This switch controls the up and down movement of the winch.
BOOM (Up / Down)
This switch controls the up and down position of the boom.
BOOM (Out / In)
This switch controls the extension (length) of the boom.
The manual extension allows the boom to extend to its full length.
To use, pull the pin from the boom, extend pull the manual
extension out to its intermediate or full length. Then insert pin
through the hole in the boom.
ROTATION (Left / Right)
This switch controls the left and right rotation of the crane.
AUTOMATIC CONTROL SYSTEMS
Overload Sensing SystemIf the capacity of the crane is exceeded, the overload system will sound an
alarm. Do not exceed the load capacity. When alarm is activated, reduce
the load before continuing.
WARNINGD Always follow the load chart
when lifting heavy loadsD Failure to follow the load
chart could result in deathor serious injury.
SECTIONDATE
SUPERSEDES
TITLE
CT310KX
C1003-4-14C
10-24-13B
SETUP & TRAVEL PREP
20569
®MANUFACTURING, INC.
CINCINNATI, OHIO
NOTESTRUCK SETUP FOR OPERATION
1. The truck should be parked on firm, level ground when using thecrane.
2. The crane should be positioned close to the job so that it canoperate within its capacity limits.
3. Set the truck parking brake.4. Put the truck's transmission in Neutral (Park if it has an automatic
transmission).5. Remove the pendant from its stowed location and plug it into its
socket.6. Turn on the master disconnect switch.7. Set the stabilizers (when provided) to help stabilize the truck to
prevent rocking or overturning of the truck when using the crane.
USING THE SWIVEL LOAD BLOCKThe swivel load block must be used for loads 1000 pounds and greater. Itmay be used for all loads to prevent twisting and turning of the load.
PREPARATION FOR TRAVEL
1. Return the stabilizers (if used) to the stowed position. Install andsecure all pins.
2. Run the BOOM IN to fully retract the boom.3. Manually retract the boom's manual extension (if used).
3.1. Pull the pin from the boom and push the extension into
the fully retracted position.
3.2. Insert the pin in the hole in the boom.
4. Run the BOOM DOWN to lower the boom to the stowed position.5. Unplug the pendant control cord and stow in a body compartment
or the truck cab.6. Turn off the master disconnect switch.
CT310KX DESCRIPTION & SPECIFICATIONS
TW
O-P
AR
TLIN
EC
ON
FIG
UR
AT
ION
C1
00
CT
31
0K
X
10
-24
-13B
DA
TE
SE
CT
ION
SU
PE
RS
ED
ES
TIT
LE
207
29
08
-12
-13A
®M
AN
UF
AC
TU
RIN
G,IN
C.
CIN
CIN
NA
TI,
OH
IO
TO
EN
AB
LE
TW
O-P
AR
TL
INE
CO
NF
IGU
RA
TIO
N
RE
MO
VE
LY
NC
HP
INF
RO
MB
OO
MH
EA
DP
INA
ND
RE
MO
VE
BO
OM
HE
AD
PIN
FR
OM
BO
OM
ALIG
NW
IRE
RO
PE
HO
OK
AS
SH
OW
NR
EIN
SE
RT
BO
OM
HE
AD
PIN
AN
DL
YN
CH
PIN
INS
TA
LL
LO
AD
BL
OC
KO
NW
IRE
RO
PE
LO
AD
BL
OC
K
BO
OM
HE
AD
PIN
WIR
ER
OP
EH
OO
K
WIR
ER
OP
E
LY
NC
HP
IN
TW
O-P
AR
TLIN
EC
ON
FIG
UR
AT
ION
(US
ING
LO
AD
BLO
CK
)
*T
he
sw
ivello
ad
blo
ck
must
be
used
for
loads
1000
pounds
and
gre
ate
r.
SECTION 150
SAFETY
8604150
SECTIONDATE
SUPERSEDES
TITLE
CT310KX
C15008-12-13A
11-04-02
GENERAL SAFETY
20556
R
MANUFACTURING, INC.
CINCINNATI, OHIO
CT310KX SAFETY - GENERAL
NOTESSAFETY - GENERALWith the proper installation, cranes can be operated and maintained safely.By using common safety practices along with an awareness of potentialhazards, the job can be done safely.
Each time a crane is used, there may be a new and different environment.Each time, there is a need to look at these situations for potential hazards.Where you park your truck is important for the work to be done, and donesafely. Asking others to stop or move their activity away from your truckmay be best. And, of course, there is the need to look for overhead powerlines and other obstacles to avoid during the operation of the crane.Sometimes, the load itself can present a hazard; for example, loads may bedamaged or broken, the load may contain hazardous material, or the loadmay come close to exceeding the maximum capacity of the crane.
Safety awareness is a continuing job. Below is a list of general points forsafe crane operation. Read these points and add your own points. Theremay be unique safety needs for the use of your crane and the product orservice you provide.
CRANE SAFETY
D Always turn off the truck ignition and master disconnect switchbefore performing any maintenance or repairs to the craneequipment.
D Never walk or stand under the boom or a suspended load.D Never operate the crane with a frayed cable (wire rope).D Never allow the crane to be used to lift, support, or otherwise
transport personnel.D Training by a knowledgeable crane operator is required before
operating the crane.D Read and understand this manual before operating the crane.D Always warn others to stand clear of your operating area.D Always inspect the crane each day before use for safe operating
condition.D Always refer to the load capacity chart before before using crane.D Always attach pendant cord support snap to the attachment point
before plugging in the pendant.D Always unplug the pendant when the crane is not in use.D Always turn off the master disconnect switch when the crane is not
in use.D Always place the crane in the stowed position before traveling.
SECTIONDATE
SUPERSEDES
TITLE
CT310KX
C15008-12-13A
11-04-02
HZRDS & CLEARANCES
20557
R
MANUFACTURING, INC.
CINCINNATI, OHIO
CT310KX SAFETY - GENERAL
NOTESELECTROCUTION HAZARD
Cranes are capable of contacting overhead obstructions. Power lines
create a special hazard. In addition to direct contact, just getting close to
these lines is a hazard. The higher the voltage carried by those lines, the
higher the danger. This hazard has its own set of special safety rules.
CRANE SAFETY NEAR POWER LINES
D Always remember, the truck and crane are not insulated!
D Always maintain a safe distance from power lines. Crane must
remain at least 20' away from power lines at full extension
including load and load line. Increased distance may be required
due to boom deflection or windy conditions.
D D If you encroach closer than 20', voltage must be known;
then follow the tables below.
NEVER make a lift under any power line.
D Failure to follow these rules can result in death or serious injury!
Voltage (Nominal,kV,alternating current)
0 - 50Over 50 - 200
Over 200 - 350Over 350 - 500Over 500 - 750
Over 750 - 1000Over 1000
Voltage (Nominal,kV,alternating current)
0 - 0.75Over 0.75 - 50Over 50 - 345
Over 345 - 750Over 750 - 1000
Over 1000
Minimum Clearance Distance(Feet)*
101520253540†
While Traveling - Minimum ClearanceDistance (Feet)*
46
101620†
† As established by theutility owner / operatoror registeredprofessional engineerwho is a qualifiedperson with respect toelectrical powertransmission anddistribution.
* Environmentalconditions such as fog,smoke, or precipitationmay require increasedclearances.
TABLE A - MINIMUM CLEARANCE DISTANCES
TABLE T - MINIMUM CLEARANCE DISTANCES IN TRANSIT
SECTIONDATE
SUPERSEDES
TITLE
CT310KX
C15008-12-13A
11-04-02
WARNING EXPLANATION
20558
R
MANUFACTURING, INC.
CINCINNATI, OHIO
CT310KX SAFETY - GENERAL
NOTESSAFETY WARNINGSSafety warnings have been included in this manual to alert you to the
need for care in specific procedures. These warnings include the use of
three [3] terms; DANGER, WARNING, and CAUTION. Their uses are
defined as follows:
DANGER
WARNING
CAUTION
Any DANGER indicates that failure to follow this safe practice could resultin death or serious injury.
Any WARNING indicates that failure to follow this safe practice couldresult in injury.
Any CAUTION indicates that failure to follow this instruction could result inminor injury or damage to the equipment.
D Always used to warn ofhazards that could result indeath or serious injury.
D Always used to warn ofhazards that could result ininjury.
D Always used to warn ofhazards that could result inequipment damage orserious injury.
SECTIONDATE
SUPERSEDES
TITLE
CT310KX
C15010-24-13B
08-12-13A
ELECT. HAZARD SIGNS
20559
®MANUFACTURING, INC.
CINCINNATI, OHIO
NOTESELECTROCUTION HAZARD SIGNSTwo [2] decals are provided with the crane:
ELECTROCUTION HAZARDKEEP CLEAR OF TRUCK AND LOADDEATH OR SERIOUS INJURY CAN RESULT FROM
CONTACT WITH THE LOAD, THE CRANE, OR THE
VEHICLE IF BOOM OR LOAD LINE SHOULD
BECOME ELECTRICALLY CHARGED.15393-C
! DANGER
This sign is to be placed on all four (4) sides of the truck. Each is to beplaced in a readily visible location for all to see. This sign is provided withthe crane. Additional signs are available from Venco Venturo IndustriesLLC. The sign part number is 15393.
D A N G E R!UNLAWFUL TO OPERATE THIS EQUIPMENT
WITHIN 20 FEET OF HIGH-VOLTAGE LINESOF 350,000 VOLTS OR LESS.
FOR MINIMUM CLEARANCES OF HIGH-VOLTAGE LINES IN EXCESS OF 350,000 VOLTS, REFERENCE OSHA 1926.1408,CRANE'S SAFETY MANUAL, AND CAL-OSHA ARTICLE 37, TITLE 8, HIGH-VOLTAGE ELECTRICAL SAFETY ORDERS.
15401-D
This sign is a reminder of the legal responsibility of any person operatingthe crane near high voltage lines. The sign is placed on the controlpendant side of the crane. This sign is provided with the crane. Additionalsigns are available from Venco Venturo Industries LLC. The sign partnumber is 15401.
Decals and signs have been placed on the crane as reminders of the careand precautions needed for safety. These items are to be inspectedperiodically for readability and need for replacement. The preventivemaintenance information includes an inspection of these decals and signs(Reference DWG 20571). Any unreadable or missing decal or sign mustbe replaced. See Illustrated Parts List for ordering information.
CT310KX SAFETY - GENERAL
SECTIONDATE
SUPERSEDES
TITLE
CT310KX
C15010-24-13B
08-12-13A
SAFETY SIGNS & DECALS
20560
®MANUFACTURING, INC.
CINCINNATI, OHIO
! DANGER ! DANGER
! WARNING
THE LAST FIVE [5]WRAPS OF WIRE ROPEMUST BE LEFT ON THEDRUM TO ASSIST THEWIRE ROPE CLAMP INHOLDING THE LOAD
DO NOT DISENGAGEWINCH UNDER LOAD
WINCHES ARE NOT TOBE USED FOR THELIFTING OR MOVINGOF PERSONS
SAFETY SIGNS & DECALSAll cranes are equipped with warning and informational signs and decals. Each sign and decal is
positioned to provide reminders for safe efficient operating and maintenance procedures for the crane.
Below is a description of the winch safety warnings.
Unreadable or missing signs and decals must be replaced. The next page describes the location and
part number for each. Refer to the Illustrated Parts Catalog section for parts ordering information.
WINCH SAFETYThe use of the crane involves careful use of its winch. Below are three [3] danger reminders of very
important rules.
SEE THE NEXT
PAGE FOR
ADDITIONAL
INFORMATION!
CT310KX SAFETY - GENERAL
SECTIONDATE
SUPERSEDES
TITLE
CRANES
C15010-24-13D
04-02-13C
SAFETY DECALS
21353
®MANUFACTURING, INC.
CINCINNATI, OHIO
PART NO.: 15392
DECAL: DANGER - ELECTROCUTION HAZARD
FUNCTION: To inform the operator that the machine(crane) represents an electrocution hazardshould it come close to or in contact withelectrical voltage source.
QUANTITY: 1
PLACEMENT: Rear cover.
PART NO.: 15391
DECAL: DANGER - NOT PASSENGER LIFT
FUNCTION: To inform the operator not to lift, support ortransport personnel, and to ensure that craneoperator is adequately trained.
QUANTITY: 1
PLACEMENT: Rear cover.
PART NO.: 15390
DECAL: CAUTION - INSPECT VEHICLE & CRANE
FUNCTION: To inform the operator of key operatingrequirements.
QUANTITY: 1
PLACEMENT: Rear cover.
PART NO.: 15401
DECAL: UNLAWFUL TO OPERATE
FUNCTION: To inform the operator of proper operation invicinity of power lines.
QUANTITY: 1
PLACEMENT: Right side of housing.
PART NO.: 15393A
DECAL: DANGER - ELECTROCUTION HAZARD
FUNCTION: Warns of danger from electrically chargedvehicle, crane or lead.
QUANTITY: 4
PLACEMENT: One on each side and each end of vehicle.
DANGER!THIS CRANE IS NOT A PASSENGER LIFTIT IS NOT DESIGNED OR INTENDED TO BE USED TO LIFT,SUPPORT OR OTHERWISE TRANSPORT PERSONNEL.
YOU MUST NOTOPERATE THIS CRANE UNLESS:
1. YOU HAVE BEEN TRAINED IN THE SAFEOPERATION OF THIS CRANE; AND
2. YOU KNOW AND FOLLOW THE SAFETY ANDOPERATING RECOMMENDATIONS CONTAINED INTHE MANUFACTURER'S MANUALS, YOUREMPLOYER'S WORK RULES, AND APPLICABLEGOVERNMENT REGULATIONS.
AN UNTRAINED OPERATOR SUBJECTS HIMSELFAND OTHERS TO DEATH OR SERIOUS INJURY.
15391-D
THIS MACHINE IS NOT INSULATED
ELECTROCUTION HAZARDMAINTAIN SAFE CLEARANCES FROM ELECTRICAL
LINES AND APPARATUS. YOU MUST ALLOW FOR
BOOM SWAY, ROCK OR SAG, AND ELECTRICAL
LINE AND LOAD LINE SWAYING.
THIS LIFTING DEVICE DOES NOT PROVIDE PRO-TECTION FROM CONTACT WITH OR PROXIMITY
TO AN ELECTRICALLY CHARGED CONDUCTOR.
YOU MUST MAINTAIN A CLEARANCE OR AT LEAST 10FEET BETWEEN ANY PART OF THE CRANE, LOAD
LINE OR LOAD, AND ANY ELECTRICAL LINE OR
APPARATUS CARRYING UP TO 50,000 VOLTS. ONE
FOOT ADDITIONAL CLEARANCE IS REQUIRED FOR
EVERY ADDITIONAL 30,000 VOLTS OR LESS.
DEATH OR SERIOUS INJURY WILL RESULT FROMCONTACT OR INADEQUATE CLEARANCE.
15392-E
DANGER
15390-D
! CAUTION1. INSPECT VEHICLE AND CRANE INCLUDING
OPERATION, PRIOR TO USE DAILY.
2. DO NOT USE THIS EQUIPMENT EXCEPT ONSOLID, LEVEL SURFACE WITH CRANE MOUNTEDON FACTORY-RECOMMENDED TRUCK.
3. BEFORE OPERATING THE CRANE, REFER TOMAXIMUM LOAD (CAPACITY) CHART ON CRANEFOR OPERATING (LOAD) LIMITATIONS.
4. DO NOT OPERATE, WALK, OR STAND BENEATHBOOM OR A SUSPENDED LOAD.
5. UNPLUG PENDANT AND SHUT OFF MASTER
DISCONNECT SWITCH WHEN CRANE NOT INUSE.
6. FOR TRAVEL, BOOM MUST BE IN STOWED
POSITION.
D A N G E R!UNLAWFUL TO OPERATE THIS EQUIPMENT
WITHIN 20 FEET OF HIGH-VOLTAGE LINESOF 350,000 VOLTS OR LESS.
FOR MINIMUM CLEARANCES OF HIGH-VOLTAGE LINES IN EXCESS OF 350,000 VOLTS, REFERENCE OSHA 1926.1408,CRANE'S SAFETY MANUAL, AND CAL-OSHA ARTICLE 37, TITLE 8, HIGH-VOLTAGE ELECTRICAL SAFETY ORDERS.
15401-D
ELECTROCUTION HAZARDKEEP CLEAR OF TRUCK AND LOAD
DEATH OR SERIOUS INJURY CAN RESULT FROM
CONTACT WITH THE LOAD, THE CRANE, OR THE
VEHICLE IF BOOM OR LOAD LINE SHOULD BECOME
ELECTRICALLY CHARGED.15393-C
! DANGER
PART NO.: 15513
DECAL: MASTER DISCONNECT SWITCH
FUNCTION: To inform the operator of locationand operation of master disconnectswitch.
QUANTITY: 1
PLACEMENT: On master disconnect switch bracket.
SECTIONDATE
SUPERSEDES
TITLE
CRANES
C15006-06-14C
04-02-13B
SAFETY DECALS
21384
®VENCO VENTURO INDUSTRIES LLC
CINCINNATI, OHIO
PART NO.: 20927
DECAL: CRANE STABILITY
FUNCTION: To inform the operator of the crane's liftingcapacity throughout the entire rotation.
QUANTITY: 1
PLACEMENT: In prominent location, so it is easily seen andreadily identifiable.
%
%
%
%
%%
%
%
%
%
NO LIFTING
S T A B I L I T Y C H A R T
20927
PERMITTED IN THIS AREA
ZONE 1ZONE 10
ZONE 9
ZONE 8
ZONE 2
ZONE 3
ZONE 4
ZONE 5ZONE 6
ZONE 7
D BASED UPON THE FINAL INSTALLED PACKAGE, THIS CRANE MAY NOT BE ABLE TOLIFT TO FULL CAPACITY THROUGHOUT THE ENTIRE CRANE ROTATION. REFER TOTHE DIAGRAM BELOW, ALONG WITH THE CRANE'S LOAD CHART, TO DETERMINE THEMAXIMUM CAPACITY FOR VARIOUS ROTATION ZONES.
FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY OR DEATH
D A N G E R
SECTIONDATE
SUPERSEDES
TITLE
VENTURO CT310KX
C15010-24-13B
08-12-13A
DECAL DRAWING & LIST
21377
®MANUFACTURING, INC.
CINCINNATI, OHIO
PART NO.: 15398
DECAL: UNPLUG REMOTE CONTROL
FUNCTION: To inform the operator to unplugremote control when not in use.
QUANTITY: 1
PLACEMENT: Near pendant socket.
PART NO.: 20470-1 & 20470-2 (OPPOSITE)
DECAL: BOOM ANGLE
FUNCTION: To inform of the boom angle.
QUANTITY: 1 Each.
PLACEMENT: One on each side of boom..
PART NO.: 16719
DECAL: UNLAWFUL TO OPERATE
FUNCTION: To inform the operator of properoperation in vicinity of power lines.
QUANTITY: 1
PLACEMENT: Left side of boom.
PART NO.: 573403
DECAL: WARNING - STOWING
FUNCTION: To inform the operator stay awayfrom the boom when stowing.
QUANTITY: 1
PLACEMENT: Rear cover.
PART NO.: 573402
DECAL: DANGER - TWO BLOCKING HAZARD
FUNCTION: To inform the operator to avoid two-blocking.
QUANTITY: 1
PLACEMENT: Rear cover.
UNPLUGREMOTE CONTROL
PENDANT WHEN
NOT IN USE15398-F
UNLAWFUL TO OPERATE THIS EQUIPMENTWITHIN 10 FEET OF HIGH - VOLTAGE LINES
16719-D
0°
1750
1100
755
20470-1CT310KX
SECTIONDATE
SUPERSEDES
TITLE
CT310KX
C15010-24-13D
08-12-13C
DECAL DRAWING & LIST
21378
®MANUFACTURING, INC.
CINCINNATI, OHIO
PART NO.: 20504
DECAL: MODEL NUMBER
FUNCTION: To show the model of the crane.
QUANTITY: 1
PLACEMENT: Left side of boom..
PART NO.: 13397
DECAL: OIL LEVEL
FUNCTION: To inform the operator of proper oil level to maintain.
QUANTITY: 1
PLACEMENT: Right side of power unit.
PART NO.: 14459
DECAL: OVERLOAD ALARM SYSTEM
FUNCTION: To inform the operator of theoverlaod conditions & remedies.
QUANTITY: 1
PLACEMENT: Rear cover.
13
39
7-E
Retract All CylindersPrior to Servicing
AW46 or DEXRON III ATF
OIL LEVEL
14459-E
THIS CRANE IS EQUIPPED WITH AN OVERLOAD ALARM SYSTEM1. OVERLOAD ALARM HORN SOUNDS IF RATED LOAD IS EXCEEDED AT ANY REACH.2. IF ALARM SOUNDS, RAISE BOOM OR LOWER WINCH TO REMOVE OVERLOAD.
3. ALWAYS RAISE BOOM SLIGHTLY BEFORE LIFTING LOAD. WARNING SYSTEMINOPERATIVE WHEN CYLINDER IS COMPLETELY BOTTOMED.
4. ALARM CAN BE TESTED BY TYING DOWN BOOM WITH WINCH CABLE AND OPERATINGBOOM UP OR BY RAISING BOOM AGAINST UP LIMIT STOP.
NOTICE - WARRANTY VOID IF DISCONNECTED
THIS ALARM SYSTEM HAS BEEN INSTALLED AS A SAFETY FEATURETO PROTECT BOTH THE EQUIPMENT AND THE OPERATOR.
DO NOT DISCONNECT THIS SYSTEM
SECTION 200
INSTALLATION
7607200A
SECTIONDATE
SUPERSEDES
TITLE
CT310KX
C2003-4-14H
2-18-14G
INSTALL INSTRUCTIONS
20563
®MANUFACTURING, INC.
CINCINNATI, OHIO
CT310KX INSTALLATION INSTRUCTIONS
NOTESINSTALLATION PROCEDUREYour new crane is shipped in a ready-to-install condition. Follow theinstructions in this section tp properly install the crane onto your truck.
INSPECT FOR SHIPPING DAMAGEInspect the crane immediately upon receipt, even if installation will notoccur immediately.D Remove packaging materials as neededD Inspect for crushed, bent, or otherwise damaged conditionsD Report any damage found to the carrier
CRANE MOUNTINGRefer to drawing 20564 if your crane has 'Continuous Rotation' or 27410 if
your crane has 'Adjustable Limited Rotation' (340º).
Recommended Mounting Hardware:
The crane base is mounted using four [4] 3/4-10 x 2 34" (bolt length will
vary per mounting application), zinc - plated (GR.5 or greater) hex headcap screw bolts, [8] flat washers, and [4] nylon - insert hex 'Full' lock nuts.
Note: This hardware is NOT supplied due to the varying bolt lengthrequirements per application.
Torque hex nuts to standard toque value of 230 ft.-lbs.
INSTALL BATTERY CABLESRefer to drawing 20565
1. Install #2 gauge wiring1.1. Be sure to install a circuit breaker into the wiring from the battery
(P/N 22946 recommended).2. Install grounding straps
2.1. Install #2 gauge grounding strap from rane base to truck frame.2.2. If truck battery negative terminal is connected to engine, install a
#2 gauge grounding strap from the engine to truck frame.
WIRE ROPE INSTALLATIONRefer to drawing 20574 (MAINTENANCE SECTION) for information onwire rope installation / replacement.
C2
00
DIM
EN
SIO
ND
RA
WIN
G
CT
31
0K
XW
/C
ON
TIN
UO
US
RO
TA
TIO
N
12-4
-14F
DA
TE
SE
CT
ION
SU
PE
RS
ED
ES
TIT
LE
20564
R
MA
NU
FA
CT
UR
ING
,IN
C.
CIN
CIN
NA
TI,
OH
IO
C.G
.(A
PP
RO
X)
32"
32"
117"
85"
53"
9"
9"
ST
OW
ED
PO
SIT
ION
MA
NU
AL
(PO
WE
R)
HY
DR
AU
LIC
64
-3/4
"
40
"
R1
3-1
/8"
SLE
WD
RIV
EM
OT
OR
TU
RN
ING
RA
DIU
S=
13-1
/8"
8"
R1
3-1
/8"
SW
ING
RA
DIU
SW
INC
HA
ND
SLE
WD
RIV
EM
OT
OR
MO
UN
TIN
GP
LA
TE
&H
OLE
CE
NT
ER
-TO
-CE
NT
ER
DIM
'S.
10
" 25
"
10
1 2
10
1 2
3-4
-14E
10
3-1
/2"
13
0-1
/4"
15
6"
SECTIONDATE
SUPERSEDES
TITLE
CT310KX
C2001-15-14C
03-12-13B
BASE MOUNTING DIM
20714
R
MANUFACTURING, INC.
CINCINNATI, OHIO
CT310KX MOUNTING DIMENSION
REFERENCE INSTALLATION DWG 20563 FORMOUNTING BOLT SIZE AND TORQUE SPECIFICATIONS.
BA
TT
ER
YC
AB
LE
INS
TA
LL
AT
ION
C2
00
CT
31
0K
X
10
-24
-13B
DA
TE
SE
CT
ION
SU
PE
RS
ED
ES
TIT
LE
205
65
08
-12
-13A
®M
AN
UF
AC
TU
RIN
G,IN
C.
CIN
CIN
NA
TI,
OH
IO
Import
ant:
Th
ecr
ane
must
make
connectio
nw
ith
the
ne
gative
ofba
ttery
.T
oensu
reth
is:
1.
Inst
all
a#2
gaug
egro
und
ing
stra
pfr
om
the
engin
eto
the
tru
ckfr
am
e(r
equired
ifnegativ
efr
om
battery
isco
nne
cted
toth
eeng
ine).
2.
Inst
all
a#2
gaug
egro
und
ing
stra
pfr
om
the
cra
ne
base
toth
etr
uck
fram
e(incl
uded).
NO
TE
:F
ailu
reto
pe
rfo
rmth
ese
ste
ps
may
resu
ltin
inte
rmitte
nt
ope
ratio
nofele
ctric
crane.
Engin
eto
truck
fram
e
Mast
er
dis
con
nect
sw
itch
necess
ary
for
safe
ty+
12V
FU
SE
BA
TT
ER
Y
Fuse
or
circ
uit
bre
ake
r(P
/N22
946
)re
com
mended.
Loca
teas
clo
seto
sta
rte
ro
rb
att
ery
as
ispra
ctic
al.
Pow
er
unit
cable
Attach
cable
tob
atte
ryte
rmin
al
or
sta
rter
sole
noid
("hot"
sid
e)
SECTIONDATE
SUPERSEDES
TITLE
CT310KX
C20008-12-13A
11-04-02
FINAL PREP FOR USE
20566
R
MANUFACTURING, INC.
CINCINNATI, OHIO
CT310KX INSTALLATION INSTRUCTIONS
NOTESFINAL PREPARATION FOR USE
1. Check all bolts and nuts for tightness.
2. Check all electrical connections for tightness.
3. Inspect the entire crane to be sure that it is ready for use.
4. Verify that the hydraulic reservoir is filled with hydraulic fluid (withboth cylinders fully retracted).
5. Check the crane operation.5.1. Put the truck's transmission in Neutral (Park if it has an
automatic transmission).
5.2. Remove the pendant from its stowed location and plug it
into its socket.
5.3. Check each of the four operations by operating each
switch in both directions:
5.3.1. WINCH down / up
5.3.2. BOOM up / down
5.3.3. BOOM out / in
5.3.4. ROTATION left / right
NOTE: The crane is now ready for operation.
6. After 10 hours of operation, repeat steps 1 through 4.
SECTION 300
MAINTENANCE
&
SERVICE
7607300A
SECTIONDATE
SUPERSEDES
TITLE
CT310KX
C30008-12-13A
11-04-02
PRVNTV MAINTENANCE
20571
R
MANUFACTURING, INC.
CINCINNATI, OHIO
CT310KX MAINTENANCE & SERVICE
NOTESPREVENTIVE MAINTENANCE
OverviewYour preventive maintenance program should include all of the following
inspections and lubricant applications. Additional items can be added to
meet your special needs. New cranes should be fully inspected and have
the hydraulic fluid replaced after the first 10 hours of operation.
Periodic InspectionHaving scheduled inspections helps ensure your crane will stay in a ready
to use condition. As parts become worn, replacement parts can be
ordered in advance to allow timely repair. Downtime for the crane can be
limited.
Table 4-1 suggests a monthly and annual inspection, but a general
inspection should be performed daily and each time the crane is used.
D Are there obvious wear or damage problems?
D Does the crane sound normal? Are there changes in the
sounds of the winch motor or hydraulic pump and motor?
D Is the crane operating smoothly?
Table 4-1 Periodic Inspection Schedule
PERIODIC INSPECTION SCHEDULEInspection Frequency
Monthly
Annually
Inspection
Inspect all moving parts forwear or damage.
Check hydraulic hoses andfittings for leaks.
Check hydraulic cylinders forleaks.
Check all nuts and bolts fortightness.
Check all decals and signs forreadability.
Action
Repair or replace as needed.
Repair or replace as needed.
Repair or replace as needed.
Tighten as needed.
Clean, repair, or replace asneeded. (Refer to the decaldrawing in the safety or partssection(s)).
LU
BR
ICA
TIO
N&
MA
INT
EN
AN
CE
CH
AR
TC
300
CT
31
0K
X
10
-24
-13A
DA
TE
SE
CT
ION
SU
PE
RS
ED
ES
TIT
LE
219
82
08
-21
-13
®M
AN
UF
AC
TU
RIN
G,IN
C.
CIN
CIN
NA
TI,
OH
IO
Tim
eof
Tru
ckS
erv
ice
No
teS
erv
ice
Inte
rval
Gre
ase
fitt
ing
With
Pre
ssure
Gre
ase
Gun
Use
Lith
ium
Base
dG
rease
Fill
Oil
Re
serv
oir
toO
ilL
evelw
ith
Bo
om
Dow
n
A B
Lo
ca
tion
Se
rvic
eR
equired
Tim
eof
Tru
ckS
erv
ice
Tim
eof
Tru
ckS
erv
ice
Bo
lts
sh
ou
ldbe
torq
ued
to230
ft-lbs
DC
he
ck
Wir
eR
op
eand
Hook
Ro
pe
sh
ou
ldbe
fre
eo
fkin
ksand
frayi
ng
CC
he
ck
To
rqu
eofbolts
Use
De
xtr
on
IIIA
TF
or
ISO
Gra
de
AW
46
for
Am
bie
nt
Te
mpera
ture
sB
etw
ee
n-2
2°
Fa
nd
30°F
Use
ISO
Gra
de
68
or
Eq
uiv
ale
nt
for
Am
bie
nt
Te
mp
era
ture
sB
etw
een
10
°F
an
d125°
F
Tim
eof
Tru
ckS
erv
ice
an
da
sre
qu
ried
by
ch
an
ge
sin
the
am
bie
nt
tem
pera
ture
ran
ge
or
Eve
ry6
month
s
DA
NG
ER
!C
AU
TIO
N DA
NG
ER
!
TH
ISC
RA
NE
ISE
QU
IPP
ED
WIT
HA
NO
VE
RLO
AD
ALA
RM
SY
ST
EM
NO
TIC
E-
WA
RR
AN
TY
VO
IDIF
DIS
CO
NN
EC
TE
D
DO
NO
TD
ISC
ON
NE
CT
TH
ISS
YS
TE
M
A
D
C
D
B
A
BA
CK
RIG
HT
LE
FT
AG
RE
AS
E;
1P
LA
CE
INS
IDE
OF
SLE
WD
RIV
ET
HR
OU
GH
AC
CE
SS
PA
NE
L
SECTIONDATE
SUPERSEDES
TITLE
CT310KX
C30010-24-13B
08-12-13A
VOLTAGE TEST
20573
®MANUFACTURING, INC.
CINCINNATI, OHIO
MINIMUM VOLTAGE TESTThis test checks the system voltage when under a full load condition. If a
minimum of nine [9] volts is not read, the battery must be changed.
To check:
1. Start the truck engine.
2. Operate the Boom Up switch until the boom is at full UP position.
3. Pull back the rubber boot which covers the motor terminal.
4. While holding the Boom Up switch on, measure the voltage at the
HOT connection (at the hydraulic pump motor) across to ground (on
the crane housing).
5. Operate the Boom Down switch to lower the boom.
6. Replace the battery if the reading is less than nine [9] volts.
DANGERD Never touch moving partsD Allow only trained personnel to
perform this test.D Failure to follow this could result
in death or serious injury.
Pull back rubber boot and put positivelead of multi-meter (voltmeter) here.
CT310KX MAINTENANCE & SERVICE
SECTIONDATE
SUPERSEDES
TITLE
CT310KX
C30008-12-13A
11-04-02
WIRE ROPE REPLCMNT
20574
R
MANUFACTURING, INC.
CINCINNATI, OHIO
CT310KX MAINTENANCE & SERVICE
WINCH LINE (WIRE ROPE) REPLACEMENT
1. Remove the wedge from the old winch line for use with the new line.
2. Remove the old winch line and clean the winch if needed.
3. Unroll the new winch line to prevent kinking.
4. Thread the new winch line through the slot in the drum.
5. Insert the new line through the slot in the drum.
6. Form a loop and insert the end of the line into the slot.
6.1. Be sure the "live", or load carrying, end of the line is against the drum flange.
6.2. Be sure the end of the rope extends out of the slot.
7. Insert the wedge into the loop.
7.1. Seat the wedge into the slot.
8. Turn the truck engine ON.
9. Wind the line onto the drum by pressing the Winch Up switch.
9.1. Maintain tension on the line at all times.
9.2. Wind the line evenly onto the drum.
M
SECTIONDATE
SUPERSEDES
TITLE
CT310KX
C30008-12-13A
11-04-02
HYDRAULIC SCHEMATIC
20575
R
MANUFACTURING, INC.
CINCINNATI, OHIO
CT310KX MAINTENANCE & SERVICE
"P"
"T"
M
S2
S2
SV
1
S1
S1
S2
S1
SV
3S
V2
P
ELEVATIONCYLINDER
EXTENSIONCYLINDER
SV2
OPERATION
A
B
C
D
E
FT
SV1
ENERGIZE "S2"OPEN FLOW'P' TO 'A''B' TO 'T'ENERGIZE "S1"OPEN FLOW'P' TO 'B''A' TO 'T'
ENERGIZE "S2"OPEN FLOW'P' TO 'C''D' TO 'T'ENERGIZE "S1"OPEN FLOW'P' TO 'D''C' TO 'T'
SV3
ENERGIZE "S2"OPEN FLOW'P' TO 'E''F' TO 'T'ENERGIZE "S1"OPEN FLOW'P' TO 'F''E' TO 'T'
ROTATIONMOTOR
SECTION 400
PARTS
7607400A
RE
PLA
CE
ME
NT
PA
RT
SIL
LU
ST
RA
TIO
NC
400
VE
NT
UR
OC
T3
10
KX
2-1
1-1
4A
DA
TE
SE
CT
ION
SU
PE
RS
ED
ES
TIT
LE
20851
11-2
0-1
3
®M
AN
UF
AC
TU
RIN
G,IN
C.
CIN
CIN
NA
TI,
OH
IO
6
1
21
23
22
29
27
10
13
14
12
9
11
16
15
28
31
33
46
32
34
26
26
25
24
51
5
43
17
18
19
20
2
7
8
RE
PL
AC
EM
EN
TP
AR
TS
LIS
TR
EF
.D
WG
.20852
35
37
36
38
39
38
PR
IMA
RY
BO
OM
SE
CO
ND
AR
YB
OO
M
SE
CT
ION
-B
EA
RIN
G
SE
CT
ION
-B
EA
RIN
G
GU
IDE
PA
DS
GU
IDE
PA
DS
41 4
0
40
43 44
42 39
45
42
30
47 46
47
37
36
48
49
50
10
52
46
47
53
54
56
55
57
58
SECTIONDATE
SUPERSEDES
TITLE
VENTURO CT310KX
C4002-11-14AREPL PARTS LIST
20852
®MANUFACTURING, INC.
CINCINNATI, OHIO
REPLACEMENT PARTS ILLUSTRATION - 20851
REPLACEMENT PARTS LIST CT310
11-20-13
HY
DR
AU
LIC
SY
ST
EM
PA
RT
SD
RA
WIN
GC
400
CT
31
0K
X
3-1
3-1
4C
DA
TE
SE
CT
ION
SU
PE
RS
ED
ES
TIT
LE
209
24
2-2
1-1
4B
®M
AN
UF
AC
TU
RIN
G,IN
C.
CIN
CIN
NA
TI,
OH
IO
RL
BO
BI
BU
RR
RL
PR
ES
SU
RE
HY
DR
AU
LIC
RO
TA
TIO
NM
OT
OR
BD
ELE
VA
TIO
NC
YL
IND
ER
RR
RL
RE
PR
8
HY
DR
AU
LIC
PO
WE
RU
NIT
EX
TE
NS
ION
CY
LIN
DE
R
BI
BO
BD
BU
RR
14
15
14
12
3
13
13
21
15
11
4
BR
EA
TH
ER
CA
P
20973
9
19
RE
TU
RN
RIG
HT
SID
EL
EF
TS
IDE
ER
6 BU 14
BD 14
BO
BI
1316
7
17
25
5
1
2
18
10
13
20
22
23
24
RE
F.
HY
DR
AU
LIC
ILLU
ST
RA
TE
DP
AR
TS
LIS
TD
RA
WIN
G20925
SECTIONDATE
SUPERSEDES
TITLE
CT310KX, CONT. ROT.
C4003-13-14D
2-21-14C
HYD SYS PARTS LIST
20925
®MANUFACTURING, INC.
CINCINNATI, OHIO
NOTE: ITEMS 2 THROUGH 17 ARE INCLUDED IN THE HOSE & FITTING KIT P/N 27098.
REF. HYDRAULIC ILLUSTRATED PARTS BREAKDOWN DRAWING 20924
HYDRAULIC SYSTEM PARTS LIST
ELE
CT
RIC
AL
SY
ST
EM
DR
AW
ING
C4
00
CT
31
0K
X
1-2
0-1
4
DA
TE
SE
CT
ION
SU
PE
RS
ED
ES
TIT
LE
210
27
-
®M
AN
UF
AC
TU
RIN
G,IN
C.
CIN
CIN
NA
TI,
OH
IO01025-2*60INX
134
51
MA
ST
ER
DIS
CO
NN
EC
TS
WIT
CH
15653-60
21584
SW
IVE
LT
ER
MA
SS
Y
TE
RM
INA
L
+B
AT
TE
RY
TO
12
VD
C
45
6
71
3
29
8
DIO
DE
DIO
DE
DIO
DE
DIO
DE
DIO
DE
DIO
DE
17356
OV
ER
LO
AD
ALA
RM
WIR
EH
AR
NE
SS
18/2
x26"
RE
D(P
igta
ilfrom
ala
rm)
BLK
FM
BLK
FM
MF
24"
WH
T
9"
GR
N
9"
GR
N
18"
YE
L
8"
YE
L
18"
OR
G
8"
OR
G
18"
BR
N
8"
BR
N
8"
RE
D
8"
BLK
3"
BLK
12"
PU
R
19
81
5-2
Va
lve
Blo
ck
Ass
y
26
26
4
SO
CK
ET
WD
WU
BO
BD
+1
2V
BU
RL
BI
RR
18"
GR
N
BO
BI
BD
BU
RL
RR
24"
BLU
BA
RR
IER
ST
RIP
5"
BLK
JU
MP
ER
WIR
E
WH
T
RE
D/B
LK
+
4"
BR
N
204
99
CO
NT
AC
TO
R
GR
OU
ND
TO
FR
AM
E
GR
OU
ND
TO
FR
AM
E
24"
GR
EY
8"
GR
EY
RE
D4
3.5
"R
ED
43.5
"R
ED
17"
RE
D
14.0
"B
LA
CK
14.0
"B
LA
CK
RE
LA
Y2
27
39
WIN
CH
GR
ND
HA
RN
ES
S(2
ea)
4-1
/2"
to4
-1/2
"to
6-1
/2"
BLK
-
NO
NC
416
310
CO
NT
AC
TO
R
#2
#1
#1
#2
*R
efe
ren
ceD
WG
#21028
174
60
-220
0-2
OV
ER
LO
AD
PR
ES
SU
RE
SW
ITC
H
--
134
48
-26
OP
TIO
NA
L
194
17
-150
CIR
CU
ITB
RE
AK
ER
20
58
6
2045
6H
YD
PW
RU
NIT
RV
=2
600P
SI
SECTIONDATE
SUPERSEDES
TITLE
ET6/8/12K(X)
C40012-26-13D
08-23-12C
REPLACEMENT PARTS
21584i
®MANUFACTURING, INC.
CINCINNATI, OHIO
1
1
1
1
3
1
1
1
1
1
1
1
**
*
*
**
*
*
*
*
1*1*
21585 REPLACES & IS INTERCHANGEABLE WITH 16772 (EXCEPT*14)
SECURE WITH LOCTITE 242 BLUE
TIGHTEN UNTIL ONE THREAD IS VISIBLE ABOVE THE NUT & ENSURETHAT SPRING IS NOT FULLY COMPRESSED
TORQUE TO 30 FT-LBS, THEN TIGHTEN SET SCREW.
PIGTAIL & STUD ASSYFIBER WASHER
INSULATING BUSHING
FIBER WASHER
1/2" I.D. x 15/16" O.D. x 1/16" THK
1/2" I.D. x 1 1/4" O.D. x 1/16" THK
TEFLON WASHER
BRASS WASHER
BRASS WASHER1/2" I.D. x 1 1/4" O.D. x 5/64" THK
1/2" I.D. x 3/4" O.D. x 1/32" THK
1/2" I.D. x 11/16" O.D. x 1/32" THK
.66" O.D. x .63" W x 5/8" F.L.NYLON INSERT-JAMNUT - 1/2"-13
LOCTITE CAPSULE GRADE 242 BLUE1/2" I.D. x 7/8" O.D. x 14 GA THK
SET SCREW; CONE-PT., 10-34 x 1/4" SS
MACHINERY BUSHING
CANDLESTICK
BRASS JAM NUT - 1/2"-13NC - MODIFIED
15653-6016771-1
13410
16771-2
16770*7
16770*11
16770*10
LC-063HJ-1
!JNUT-05013N12534-4
LOCTITE-24205
21506
21029
19800
SPRING
12
3
45
6
78
9
10
1112
1314
10 11
ITEM PART NO.QTY DESCRIPTION
4
2 3
2
12
1
3
4
5
6
7
8
9
3
1
2
4
17011 RUBBER BOOT - REF
13448-XX SWIVEL PIGTAIL
* ITEMS ARE ONLY AVAILABLE IN A 21585 SERVICE PARTS KIT
1* REPL. PARTS DWG (THIS PAGE)21584i15
14
21584 SWIVEL TERMINAL ASSY
RE
PLA
CE
ME
NT
PA
RT
SD
RA
WIN
G-
CT
31
0K
X&
ET
6K
(X)
12-2
7-1
3C
DA
TE
SE
CT
ION
SU
PE
RS
ED
ES
TIT
LE
20
83
70
9-1
7-0
7B
®M
AN
UF
AC
TU
RIN
G,IN
C.
CIN
CIN
NA
TI,
OH
IO
20
78
8M
OT
OR
RE
PLA
CE
ME
NT
KIT
INC
LU
DE
SE
ND
PIE
CE
20
49
9C
ON
TA
CT
OR
21
21
4C
AB
LE
WE
DG
E
205
86
WIN
CH
RE
PL
AC
EM
EN
TP
AR
TS
SLE
WIN
GS
YS
TE
MR
EP
LA
CE
ME
NT
PA
RT
SC
400
CT
31
0K
X
01
-22
-14
DA
TE
SE
CT
ION
SU
PE
RS
ED
ES
TIT
LE
270
41
-
®M
AN
UF
AC
TU
RIN
G,IN
C.
CIN
CIN
NA
TI,
OH
IO
209
26
MO
TO
R(O
NLY
)
27
24
3S
LE
WIN
GS
YS
TE
MR
EP
LA
CE
ME
NT
PA
RT
S
CO
NT
RO
LP
EN
DA
NT
PA
RT
SD
RA
WIN
GC
400
CT
310
KX
08-1
2-1
3A
DA
TE
SE
CT
ION
SU
PE
RS
ED
ES
TIT
LE
20
58
21
1-0
4-0
2
R
MA
NU
FA
CT
UR
ING
,IN
C.
CIN
CIN
NA
TI,
OH
IO
*R
efe
ren
ce
DW
G#20583
2
3
7
6
54
1
OR
N/B
LK
-B
I
RE
D-
RL
RE
D/B
LK
-R
R
OR
N-
BO
PLU
G-
BA
CK
SID
EV
IEW
YE
L-
WU
GR
N/B
LK
-B
D
GR
N-
BU
YE
L/B
LK
-W
D
BLU
&B
LU
/BLK
-12V
+
NO
TE
:B
LA
CK
WIR
EIS
NO
TU
SE
D
WINCH
BOOM
ROTATION
LR
UP
DOWN
IN
OUT
DOWN
UP
8
7
54
3
6
91
2
201
60
4-S
WIT
CH
PE
ND
AN
T
OR
AN
GE
/BL
KW
IRE
BO
OM
IN
OR
AN
GE
WIR
EB
OO
MO
UT
RE
DW
IRE
RO
TA
TIO
NLE
FT
RE
D/B
LK
WIR
ER
OT
AT
ION
RIG
HT
GR
EE
N/B
LK
WIR
EB
OO
MD
OW
N
YE
L/B
LK
WIR
EW
INC
HD
OW
N
YE
LLO
WW
IRE
WIN
CH
UP
GR
EE
NW
IRE
BO
OM
UP
BLU
E/B
LK
WIR
E1
2V
+
SECTIONDATE
SUPERSEDES
TITLE
CT310KX
C40008-12-13A
11-04-02
CNTRL PNDNT PRTS LIST
20583
R
MANUFACTURING, INC.
CINCINNATI, OHIO
CT310KX REPLACEMENT PARTS
ITEMNUMBER
123456789
10
* Reference DWG #20582
PARTNUMBER
2626326262-20
137631979317363
15913-211557201632016420165
QTY
1144111111
PARTDESCRIPTION
PLUG, 9-HOLECORD ASSEMBLY (20 FT. LONG)SWITCH, TOGGLEBOOT, TOGGLEDECALASSEMBLY, CLAMP & TETHERHOOK, PENDANTCOVER, PENDANT HEADBASE, PENDANT HEADGASKET/CORD RESTRAINT,
PENDANT HEAD
205
04
153
98
573
403
153
90
CA
UT
ION 144
59
OV
ER
LO
AD
ALA
RM
173
89
-4
167
19
204
70
-12
04
70
-2
133
97
153
91
CR
AN
EN
OT
A
153
92
DA
NG
ER
ELE
CT
RO
CU
TIO
NH
AZ
AR
D
573
402
DA
NG
ER
BA
CK
RIG
HT
LE
FT
DE
CA
LL
OC
AT
ION
S150
CT
310
KX
07-3
0-1
2B
01-1
4-1
4C
DA
TE
SE
CT
ION
SU
PE
RS
ED
ES
TIT
LE
20561
MA
NU
FA
CT
UR
ING
,IN
C.
CIN
CIN
NA
TI,
OH
IO
VE
NT
UR
OLO
GO
(11
INC
H)
$&
#"
!%
'
UN
PL
UG
RE
MO
TE
CO
NT
RO
L
PE
ND
AN
TW
HE
N
NO
TIN
US
E1
53
98
-F
BO
OM
AN
GLE
UN
PLU
G
WA
RN
ING
ST
OW
ING
TW
O-B
LO
CK
ING
UN
LA
WF
UL
TO
OP
ER
AT
ET
HIS
EQ
UIP
ME
NT
WIT
HIN
10
FE
ET
OF
HIG
H-
VO
LT
AG
EL
INE
S1
67
19
-D
UN
LA
WF
UL
TO
OP
ER
AT
E
TH
ISM
AC
HIN
EIS
NO
TIN
SU
LA
TE
D
EL
EC
TR
OC
UT
ION
HA
ZA
RD
MA
INT
AIN
SA
FE
CLE
AR
AN
CE
SFR
OM
ELE
CT
RIC
AL
LIN
ES
AN
DA
PP
AR
AT
US
.Y
OU
MU
ST
ALLO
WFO
RB
OO
MS
WA
Y,
RO
CK
OR
SA
G,
AN
DE
LE
CTR
ICA
L
LIN
EA
ND
LO
AD
LIN
ES
WA
YIN
G.
TH
ISLIF
TIN
GD
EV
ICE
DO
ES
NO
TP
RO
VID
EP
RO
-T
EC
TIO
NF
RO
MC
ON
TA
CT
WIT
HO
RP
RO
XIM
ITY
TO
AN
EL
EC
TR
ICA
LL
YC
HA
RG
ED
CO
ND
UC
TO
R.
YO
UM
US
TM
AIN
TA
INA
CLE
AR
AN
CE
OR
AT
LE
AS
T10
FE
ET
BE
TW
EE
NA
NY
PA
RT
OF
TH
EC
RA
NE
,LO
AD
LIN
EO
RL
OA
D,
AN
DA
NY
ELE
CT
RIC
AL
LIN
EO
R
AP
PA
RA
TU
SC
AR
RY
ING
UP
TO
50
,000
VO
LTS
.O
NE
FO
OT
AD
DIT
ION
AL
CLE
AR
AN
CE
ISR
EQ
UIR
ED
FO
R
EV
ER
YA
DD
ITIO
NA
L30
,00
0V
OLT
SO
RL
ES
S.
DE
AT
HO
RS
ER
IOU
SIN
JU
RY
WIL
LR
ES
UL
TFR
OM
CO
NT
AC
TO
RIN
AD
EQ
UA
TE
CLE
AR
AN
CE
.
1539
2-E
DA
NG
ER
EL
EC
TR
OC
UT
ION
HA
ZA
RD
DA
NG
ER
153
90-D
!C
AU
TIO
N1.
INS
PE
CT
VE
HIC
LE
AN
DC
RA
NE
INC
LU
DIN
G
OP
ER
ATIO
N,
PR
IOR
TO
US
ED
AIL
Y.
2.
DO
NO
TU
SE
TH
ISE
QU
IPM
EN
TE
XC
EP
TO
N
SO
LID
,L
EV
EL
SU
RF
AC
EW
ITH
CR
AN
EM
OU
NTE
D
ON
FA
CT
OR
Y-R
EC
OM
ME
ND
ED
TR
UC
K.
3.
BE
FO
RE
OP
ER
AT
ING
TH
EC
RA
NE
,R
EFE
RTO
MA
XIM
UM
LO
AD
(CA
PA
CIT
Y)C
HA
RT
ON
CR
AN
E
FO
RO
PE
RA
TIN
G(L
OA
D)LIM
ITA
TIO
NS
.
4.
DO
NO
TO
PE
RA
TE
,W
AL
K,
OR
STA
ND
BE
NE
ATH
BO
OM
OR
AS
US
PE
ND
ED
LO
AD
.
5.
UN
PL
UG
PE
ND
AN
TA
ND
SH
UT
OFF
MA
STE
R
DIS
CO
NN
EC
TS
WIT
CH
WH
EN
CR
AN
EN
OT
IN
US
E.
6.
FO
RT
RA
VE
L,
BO
OM
MU
ST
BE
INS
TO
WE
D
PO
SIT
ION
.
INS
TR
UC
TIO
NS
!C
AU
TIO
N
DA
NG
ER
!T
HIS
CR
AN
EIS
NO
TA
PA
SS
EN
GE
RL
IFT
ITIS
NO
TD
ES
IGN
ED
OR
INT
EN
DE
DTO
BE
US
ED
TO
LIF
T,
SU
PP
OR
TO
RO
TH
ER
WIS
ET
RA
NS
PO
RT
PE
RS
ON
NE
L.
YO
UM
US
TN
OT
OP
ER
AT
ET
HIS
CR
AN
EU
NL
ES
S:
1.
YO
UH
AV
EB
EE
NT
RA
INE
DIN
TH
ES
AF
E
OP
ER
AT
ION
OF
TH
ISC
RA
NE
;A
ND
2.
YO
UK
NO
WA
ND
FO
LL
OW
TH
ES
AF
ET
YA
ND
OP
ER
AT
ING
RE
CO
MM
EN
DA
TIO
NS
CO
NT
AIN
ED
IN
TH
EM
AN
UF
AC
TU
RE
R'S
MA
NU
AL
S,Y
OU
R
EM
PL
OY
ER
'SW
OR
KR
UL
ES
,A
ND
AP
PL
ICA
BL
E
GO
VE
RN
ME
NT
RE
GU
LA
TIO
NS
.
AN
UN
TR
AIN
ED
OP
ER
AT
OR
SU
BJE
CT
SH
IMS
EL
F
AN
DO
TH
ER
ST
OD
EA
TH
OR
SE
RIO
US
INJU
RY
. 153
91
-D
PA
SS
EN
GE
RLIF
T
DA
NG
ER
!
14
45
9-E
TH
ISC
RA
NE
ISE
QU
IPP
ED
WIT
HA
NO
VE
RL
OA
DA
LA
RM
SY
ST
EM
1.
OV
ER
LO
AD
AL
AR
MH
OR
NS
OU
ND
SIF
RA
TE
DL
OA
DIS
EX
CE
ED
ED
AT
AN
YR
EA
CH
.2
.IF
AL
AR
MS
OU
ND
S,
RA
ISE
BO
OM
OR
LO
WE
RW
INC
HT
OR
EM
OV
EO
VE
RL
OA
D.
3.
AL
WA
YS
RA
ISE
BO
OM
SL
IGH
TL
YB
EF
OR
EL
IFT
ING
LO
AD
.WA
RN
ING
SY
ST
EM
INO
PE
RA
TIV
EW
HE
NC
YL
IND
ER
ISC
OM
PL
ET
EL
YB
OT
TO
ME
D.
4.
AL
AR
MC
AN
BE
TE
ST
ED
BY
TY
ING
DO
WN
BO
OM
WIT
HW
INC
HC
AB
LE
AN
DO
PE
RA
TIN
G
BO
OM
UP
OR
BY
RA
ISIN
GB
OO
MA
GA
INS
TU
PL
IMIT
ST
OP
.
NO
TIC
E-
WA
RR
AN
TY
VO
IDIF
DIS
CO
NN
EC
TE
D
TH
ISA
LA
RM
SY
ST
EM
HA
SB
EE
NIN
ST
AL
LE
DA
SA
SA
FE
TY
FE
AT
UR
ET
OP
RO
TE
CT
BO
TH
TH
EE
QU
IPM
EN
TA
ND
TH
EO
PE
RA
TO
R.
DO
NO
TD
ISC
ON
NE
CT
TH
ISS
YS
TE
M
TH
ISC
RA
NE
ISE
QU
IPP
ED
WIT
HA
NO
VE
RLO
AD
ALA
RM
SY
STE
M
NO
TIC
E-W
ARR
AN
TY
VO
IDIF
DIS
CO
NN
ECTE
D
TH
ISA
LA
RM
SY
ST
EM
HA
SB
EE
NIN
ST
AL
LE
DA
SA
SA
FE
TY
FE
AT
UR
E
TO
PR
OT
EC
TB
OT
HT
HE
EQ
UIP
ME
NT
AN
DT
HE
OP
ER
AT
OR
.
DO
NO
TD
ISC
ON
NE
CT
TH
ISS
YS
TE
M
13397-E
Re
tra
ct
All
Cylin
ders
Pri
or
toS
erv
icin
g
AW
46
or
DE
XR
ON
IIIA
TF
OIL
LE
VE
L
OIL
LE
VE
L(F
RO
NT
)
CT
310
KX
MO
DE
L
14473-2-D
GR
EA
SE
144
73
-2G
RE
AS
E;1
PLA
CE
INS
IDE
OF
SLE
WD
RIV
E
BO
OM
AN
GLE
14473-2-D
GR
EA
SE
0°
17
50
11
00
75
5
20
47
0-2
0°
17
50
11
00
75
5
20
47
0-1
CT3
10
KX
CT3
10
KX
144
73
-2G
RE
AS
E3
PLA
CE
S
TH
RO
UG
HA
CC
ES
SP
AN
EL
SECTIONDATE
SUPERSEDES
TITLE
CT310KX
-01-21-14C
04-17-13B
FIELD SRVC LABEL KIT
20585
R
MANUFACTURING, INC.
CINCINNATI, OHIO
CT310KX20503 FIELD SERVICE LABEL KIT
ITEM PART NUMBER QTY DESCRIPTION
1 20504 1 DECAL; VOLTAGE IDENTIFICATION2 20470 DECAL; BOOM ANGLE
-1 1 LEFT SIDE-2 1 RIGHT SIDE
3 - - -
4 17389-4 1 DECAL; VENTURO LOGO, SMALL5 16719 1 DECAL; UNLAWFUL TO OPERATE SIGN6 14459 1 DECAL; ALARM - OVERLOAD SENSING7 573402 1 DECAL; DANGER - 2 BLOCKING8 573403 1 DECAL; DANGER - STOWING
9 13397 1 DECAL; OIL LEVEL10 14473 3 DECAL; GREASE11 15397 1 KIT; ACCIDENT PREVENTION SIGNS12 20561 1 IDWG; DECAL APPLICATIONS13 17813 1 DECAL; OVERLOAD SENSING SYSTEM
14 - - -15 - - -16 - - -17 - - -18 - - -
19 - - -20 - - -21 - - -22 - - -23 - - -
24 - - -25 - - -26 - - -27 - - -28 - - -
Revised: June 2014
VENTURO CRANES LIMITED WARRANTY POLICY Venturo products are built to last…we guarantee them. As a purchaser of any new Venturo product covered by warranty, you will receive 1 year of the most complete coverage available…and, at no added cost to you.
1-Year Limited Warranty Policy
This limited policy warrants new products of Venturo to be free from defects in material and workmanship for a period
of one (1) year from date of original installation. This warranty covers:
Repair or replacement of product
Labor to repair or replace product
Freight to return and/or replace product
We shall not be liable for any contingent liabilities arising out of the improper function of any products. Warranty shall
become void if the product is improperly installed, modified, damaged, abused or used for application other than
intended use.
Warranty Claims
Venco Venturo Industries LLC will make a good faith effort for prompt correction or other adjustment with respect to any product, which proves to be defective after our inspection and within the warranty period. Before any repairs are attempted or before returning any product, your Venturo Distributor is required to obtain a warranty claim number. This number is necessary for any claim to be considered. To obtain a warranty claim number, Venturo requires the model and serial number. Only authorized Venturo Distributors can perform warranty. For the name and address of your local Venturo Distributor call the Warranty Claim Department - 513-772-8448. WARNING - It is the responsibility of the installer to ensure the installation is completed according to the manufacturer's recommendations, ensure the ultimate user understands how to operate product in a safe manner, and understands the need for regular service and maintenance by an authorized Venturo Distributor. No modifications or alterations may be made to any Venturo product must be done by an authorized Venturo Distributor, to the standards of the industry; including maintenance, service and affixing of all instruction, safety and warning decals. Users should again be instructed as to the safe operation at time of delivery. Maintenance, service, operation and safety warning decals are available on request from Venco Venturo Industries LLC.
VENCO VENTURO INDUSTRIES LLC 12110 BEST PLACE | CINCINNATI, OHIO 45241
P: 800-226-2238 | F: 513-326-5427 www.venturo.com
