Striped Traienslucent Layering Tutorial by Hector Vera

7/30/2019 Striped Traienslucent Layering Tutorial by Hector Vera

1/4

China Girl Image Transfer

Tutorialww.hectorverabellingen.blogspot.com

28 grams (1/2 Block) White Polymer Clay

56 grams (1 Block) Translucent Frost

6 grams Blue Premo Clay

6 grams Yellow Premo Clay

Clay dedicated Pasta Machine

4 Acrylic Brayer

Acrylic Roller

Ceramic tile

Sharp Blade

Striped Translucent Layering

[email protected]

veradesigns.com.au

Materials List


2/4

2

Step 4.

Cut each

sheet

diagonally.

Step 2.

Condition 1/2 TranslucentFrost and add four 2cm/2cm

squares of Blue Clay that has

been rolled on the #1 setting of

the Makins Pasta Machine (the

thickest setting).

Step 1.

Condition 1/2 Translucent

Frost and add four 2cm/2cm

squares of Yellow Clay that

has been rolled on the #1

setting of the Makins Pasta

Machine (the thickest setting).

Step 3.

You will now have

two sheets of

translucent clay

tinted with colour.

Rolled out on the

#1 Setting of theMakins Pasta

Machine (thethickest setting).

Step 8.

Skinner BlendCigar.

[email protected]

veradesigns.com.au

Step 5.

Now stack the

yellow to the yellow

and the blue to the

blue. Make this

into a Skinner

Blend (as shownbelow).

Step 6.

Two partSkinner Blend.

Step 7.

Roll the sheet

up so that you

are rolling upalong all three

colours.


3/4

3

Step 12.

Continue stretching out the

plug and pull it to make it

longer.

Step 10.

This is another view ofthe Skinner Blend Plug.

Now lay the plug down

so that all colours are

touching the tile.

Step 9.

Roll into a Skinner Blend Plug. Reducing

the low thing roll into a short fat one. This

is viewing the plug with the translucent blueat the bottom (on top of the tile).

To shorten the cane, compress it using a

sort of reverse reduction process, workingthe ends of the clay toward the centre.

Step 11.Stretch out the plug and pull

it to make it longer.

Continue pinching and

stretching the piece out to

form a strip approximately

twice the thickness of the

thickest setting of your pastamachine.A 4 Acrylic

Brayer is useful here.

[email protected]

veradesigns.com.au

Step 13.

Roll a sheet of white clay (1

block white clay) through the

medium-thin setting of thepasta machine (#3 on the

Makins).

Leaving a margin all around

the coloured plug of clay.

Step 14.

This is what you get (a

belt of clay) after you

have rolled the clay

through the Makins

Pasta Machine on the

#1 setting (the thickestsetting).

Step 15.

Take a ruler and

measure the length ofthe belt of clay and

cut in half.

Step 16.

Stack thehalves on top

of each other.

Top View

Bottom View


4/4

4

China Girl Image Transfer

Tutorial

Hector Vera

[email protected]

www.veradesigns.com.au

(02) 6655 9170

Step 20.

This is a view of the

Striped Translucent

Skinner Blend cane with

the bits trimmed off.

Step 18.

Cutting in half and

stacking again.

Step 17.

Cut in half and stackagain.

Step 19.

This is a side view of

the stack.

[email protected]

veradesigns.com.au

Documents

Striped Traienslucent Layering Tutorial by Hector Vera