Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
11Tungsten Carbide Catalog
22
Turning Precision into Value
33
Strauss offers highly accurate, One-piece FG tungsten carbide bur:
n Highestqualityrawmaterials:One-piecetungstencarbide: • Zerovibration. • Superiordurability. • Optimalcuttingefficiency. • Abilitytowithstandrepeatedsterilizationwithoutrusting.
n Themostconcentricbureverproduced-consistentinsizeresultingin: • Efficientcutting. • Lesschatter. • Superiorcontrol. • Betterfinish.
n CNC(ComputerNumericalControl)precisionmanufacturingproducesatopqualityrotary instrumentproductthatexceedsindustrystandardsforqualityandprecision.
n Taskandmaterialspecificbladeconfigurationsproduceoptimalcutting,efficientfinishing andoutstandingdurability.
n Sharperblades=moreworkingtimeperbur.
Strauss high precision Carbides
Intro
duct
ion
44
Operative and Surgical FG 6 Blades: •Regular shank Pages 5-8 •Short shank Pages 5-8 •Surgical length Pages 5-8
RA 6 Blades: •Regular shank Pages 5-8 •Surgical length Pages 5-8 •HP 6Blades Pages 5-8Trimming and finishing: •FG 12Blades Pages 9-12 •FG 30Blades Pages 9-12Metal cutting: •FG Barracuda metal cutting Pages 13-15
Special Products: • Zekrya Page 16 • Endo Access Page 16 • Bur Blocks Pages 17-18 • Tissue Trimming Page 19:n Forthesafetyofuserandpatient,itishighlyrecommendedthatonlyqualifieddentistsshouldworkwith dentalburs.n Attentionshouldbepaidtospeedofwork(RPM). UsingaburwithtoohighRPMlevel,couldgenerateundesirableheat.n Donotforceaburintotheturbine.Incaseofdifficultaccess,checkbothturbineandbur. Remember!Strauss&Co.dentalbursareguaranteedandshallbereplacediffoundincompatible. However,specialattentionshouldbepaidtoinstructionsofuseandmaintenanceoftheturbine.
n Strauss&Co.’sdentalbursaredesignedforseveralusesandareautoclavable.n Sterilizethebursbeforeuse.
The Right Instrument for Every Situation
Intro
duct
ion
55
6 Bladed Operative & Surgical
Cat.No. 1/4 1/2 1 2 3 4 5 6 7 8
Headsize(mm) 0.50 0.70 0.80 1.00 1.20 1.40 1.60 1.80 2.10 2.30
FG n n n n n n n n n n
FGSS n n n n
FGOS n n n n n n n n
RA n n n n n n n n n n
RASS n n
RAOS n n n n n n n
HP n n n n n n n n n n
Round Amalgam Prep
Cat.No. 245 246 256 257
Headsize(mm) 0.80 1.20 0.80 1.00
FG n n n n
FGSS n
RA n
Pear
Cat.No. 329 330 331 332
Headsize(mm) 0.60 0.80 1.00 1.20
FG n n n n
FGSS n
RA n n
6 Bl
aded
Ope
rativ
e & S
urgi
cal
66
Cat.No. 1556 1557 1558
Headsize(mm) 1.00 1.20 1.60
FG n n n
FGSS n
FGOS n n
RA n n
Round End Cross Cut Fissure
Round End Fissure
Cat.No. 1155 1156 1157 1158
Headsize(mm) 0.80 0.90 1.00 1.20
FG n n n n
FGOS n
HP n
Inverted Cone
Cat.No. 331/2 34 35 36 37 38 39
Headsize(mm) 0.70 0.80 1.00 1.20 1.40 1.60 1.80
FG n n n n n n n
FGSS n
RA n n n n
RASS n
End Cutting
Cat.No. 956 957
Headsize(mm) 0.80 1.00
FG n n
FGSS n n
6 Bl
aded
Ope
rativ
e & S
urgi
cal
77
Round End Tapered Fissure
Cat.No. 1169 1170 1171 1172
Headsize(mm) 0.90 1.00 1.20 1.60
FG n n n n
Cat.No. 700L 701L 702L
Headsize(mm) 1.00 1.20 1.60
FG n n n
Long Cross Cut Tapered Fissure
Cat.No. 1701 1702
Headsize(mm) 1.20 1.60
FG n n
FGOS n
Round End Cross Cut Tapered Fissure
Cat.No. 55 56 57 58 58L 59
Headsize(mm) 0.80 0.90 1.00 1.20 1.20 1.40
FG n n n n n n
RA n n
Fissure
6 Bl
aded
Ope
rativ
e & S
urgi
cal
88
Long Tapered Fissure
Cat.No. 169L 170L 171L
Headsize(mm) 0.90 1.00 1.70
FG n n n
Cross Cut Fissure
Cat.No. 699 700 701 702 703
Headsize(mm) 0.90 1.00 1.20 1.60 2.10
FG n n n n n
FGOS n n n
RA n n
HP n n
Cross Cut Tapered Fissure
Cat.No. 167 168 169 170 171
Headsize(mm) 0.70 0.80 0.90 1.00 1.20
FG n n n n n
FGOS n
RA n
Tapered Fissure
6 Bl
aded
Ope
rativ
e & S
urgi
cal
Cat.No. 556 557 558 559 560
Headsize(mm) 0.90 1.00 1.20 1.40 1.60
FG n n n n n
FGSS n n
FGOS n n n n
RA n n n
HP n n n n n
99
Trimming and Finishing 12 & 30 Blades
Interproximal
12Flutes 7103 7602
30Flutes 9103 9602
Headsize(mm) 1.20 1.00
12FlutesFG n n
30FlutesFG n n
12Flutes 7303 7304
30Flutes
Headsize(mm) 1.20 1.40
12FlutesFG n n
Long Pear
12Flutes 7002 7003 7004 7006 7008 7009
30Flutes 9004 9006 9008
Headsize(mm) 1.00 1.20 1.40 1.80 2.30 2.70
12FlutesFG n n n n n n
30FlutesFG n n n
12FlutesRA n
Round • 12Bladed:Controlledcontouringandfinishing.• 30Bladed:Finalsurfacerefinementandsatinpolishing. Producesasatinfinishreadyforfinalpolishing. Detailedfinishingandtexturizingofsurfaceanatomy.
Blade Geometry•Straightblades:Advancedbladeconfigurationidealforcompositematerials. Additional control - no spiraling to pull the bur or compositematerial. Producesasuperiorfinishandislongerlastingduetoidealbladecontact points.•Spiraled blades: Standard blade configuration for amalgam, metals, dentin,andcomposites.
Trim
ming
and F
inish
ing 12
& 30
Blad
es
1010
Chamfering
12Flutes 7345
30Flutes
Headsize(mm) 1.50
12FlutesFG n
Parallel Bevel
12Flutes 7283-2 7283-4
30Flutes
Headsize(mm) 1.20 1.40
12FlutesFG n n
Needle
12Flutes 7901 7902 7903
30Flutes 9903
Headsize(mm) 0.90 1.00 1.20
12FlutesFG n n n
30FlutesFG n
12Flutes 7702 7713 7714
30Flutes 9714
Headsize(mm) 1.00 1.20 1.40
12FlutesFG n n n
30FlutesFG n
Tapered
Trim
ming
and F
inish
ing 12
& 30
Blad
es
1111
12 Flutes 7642 7653 7664 7675
30 Flutes 9642
Head size (mm) 1.00 1.20 1.40 1.60
12 Flutes FG n n n n
30 Flutes FG n
Round End Taper
Straight Cylinder
12 Flutes 7572
30 Flutes 9572
Head size (mm) 1.20
12 Flutes FG n
30 Flutes FG n
12 Flutes 7283k6 7282k6
30 Flutes
Head size (mm) 1.60 1.60
12 Flutes FG n n
Currettage
Trim
ming
and F
inish
ing 12
& 30
Blad
esTr
immi
ng an
d Fini
shing
12 &
30 B
lades
12 Flutes 7611 7612
30 Flutes
Head size (mm) 1.00 1.40
12 Flutes FG n n
30 Flutes FG
Tapered
1212
12 Flutes 7404 7406 7408
30 Flutes 9404 9406 9408
Head size (mm) 1.40 1.80 2.30
12 Flutes FG n n n
30 flutes FG n n n
12 Flutes EF3 EF4 EF6 EF9
30 Flutes UF3 UF4 UF6 UF9
Head size (mm) 0.80 1.00 1.40 1.40
12 Flutes FG n n n n
30 Flutes FG n n n n
Composite Trimming
SafeEnd
12 Flutes 7800 7801 7802 7803
30 Flutes 9800 9801 9802 9803
Head size (mm) 0.70 0.90 1.00 1.20
12 Flutes FG n n n n
30 Flutes FG n n n n
Bullet
12 Flutes 7102 7104 7106 7108
30 Flutes
Head size (mm) 1.20 1.40 1.80 2.30
12 Flutes FG n n n n
30 Flutes FG
Flame
Tapered
12 Flutes 7114 7204 7205 7206 7214 7375-4
30 Flutes 9214
Head size (mm) 0.90 1.40 1.60 1.80 1.20 1.40
12 Flutes FG n n n n n n
30 Flutes FG n
SafeEnd
Trim
ming
and F
inish
ing 12
& 30
Blad
es
Egg Shape
1313
Barracuda - Metal Cutting
Barra
cuda
- Me
tal C
uttin
g
One-piece solid carbide Barracuda Super Bur Benefits:
• Maximum Value and performance.
• Crown and Bridge removal design to cut through precious and non-precious metal, sub-structure and
framework.
• Special blade geometry featuring fine cross-cuts and unique neck design produce a bur that quickly
cuts metal with reduced chatter, breakage and improved control.
• Computer aided design created to maximize performance while cutting gold, amalgam, nickel, chrome
and other metal alloys.
• No grabbing, stalling or breaking while cutting through amalgam or metals.
1414
Round End Cross Cut Fissure
Cat. No. B1557 B1558
Head size (mm) 0.80 1.00
FG n n
Cross Cut Tapered Fissure
Cat. No. B701 B702
Head size (mm) 1.20 1.60
FG n n
Round
Cat. No. B2 B4 B6 B8
Head size (mm) 1.00 1.40 1.80 2.30
FG n n n n
Cross Cut Fissure
Cat. No. B556 B557 B558
Head size (mm) 0.90 1.00 1.20
FG n n n
Barra
cuda
- Me
tal C
uttin
g
1515
Cat. No. B34 B35 B37
Head size (mm) 0.80 1.00 0.80
FG n n n
Pear
Cat. No. B330 B331 B245
Head size (mm) 0.80 1.00 0.80
FG n n n
Inverted Cone
Barra
cuda
- Me
tal C
uttin
g
1616
Endo Access
Cat. No. 152EZ
Head length (mm) 14
FG n
Endo Safe End Bur• Specially designed carbide bur with non-cutting safe-ended tip.• Safely widens pulp chamber without perforation and ledging.• Creates funnel shape to allow easier access to root canals.• Safe ended tip prevents penetration of the pulp chamber floor.
A unique bur that has a cutting tip and 6 helical flutes making them ideal for sectioning an impacted wisdom tooth prior to its extraction, separatingroots and removing.
Endo Access
ZekryaZekrya
Spec
ial P
rodu
cts
Cat. No. FGZ23 FGZ28
Head length (mm) 11 11
Total length (mm) 23 28
FG n n
1717
36FG Bur BlockPKBBP36FG1
12FG Bur BlockPKBBP12FG1
72FG Bur BlockPKBBP72FG1
Bur Blocks AutoclaveDurability
Bur Blocks
Spec
ial P
rodu
cts
SKU ProductPKBBP12FG1 Plastick Bur block - 12 FG
PKBBP36FG1 Plastic Bur block - 36 FG
PKBBP72FG1 Plastic Bur block - 72 FG
1818
5RA + 10FG Bur BlockPKBBM10FG5RA1 9RA + 18FG Bur Block
PKBBM18FG9RA1
6HP Bur BlockPKBBM6HP1
Spec
ial P
rodu
cts
SKU ProductPKBBM10FG5RA1 Aluminum Bur block - 10 FG+5 RA
PKBBM18FG9RA1 Aluminum Bur block - 18 FG+9 RA
PKBBM6HP1 Alumium Bur b lock - 6 HP
1919
• Designed for soft-tissue surgery. the ceramic soft tissue trimmer bur is a rotary instrument that can be used as an alternative to using scalpel, electro-surgery and surgical blades.• Using the tissue trimmer provides minimum bleeding.• The biocompatible hard oxide points are made to cut tissue without burning.
Tissue Trimming
Tissue Trimmer
Cat. No. FG-CER FG-CEROS
Head length (mm) 5 8
Total length (mm) 22.5 25
FG n n
Spec
ial P
rodu
cts
20
19, Hayezira St. Industrial ZoneP.O.Box 2521, Raanana, IsraelW e b : w w w. s t r a u s s - c o . c o m
Tungsten Carbide Catalog
ED:0
610 European Representative:
Strauss Industrial Diamonds Deutschland GmbHw w w. s t r a u s s - d e u t s c h l a n d . d e