ROTOFAST.COM Measure and mark the location where panel will be placed and mark the orientation on the back of the panel. Push the scratch awl though the panel at the marked locations, keeping the scratch awl as straight as possible. Place painters tape on the face of the panel at the desired anchor locations. Place panel at marked location and use scratch awl to penetrate panel and mark substrate for anchor locations. (For harder surfaces insert a nail into the hole and tap with a hammer to mark the substrate) STEP 3 STEP 2 STEP 4 Screw Rotofast Standard Anchor to wall at marked location. Make sure the anchor spins on the shaft of the screw but does not wobble. Flip arm and push hex insert ﬁrmly into center of the anchor. STEP 5 STEP 6 Rotofast Standard Anchors are a secure and fast solution for acoustical panel installation. See rotofast.com for the Rotofast Standard Anchor installation video. Step-by-Step Installation (RST3) Rotofast tm Standard Anchor 1B STEP 1A Insert the installation tool through hole in painters tape. Feel and hear the installation tool engage with the insert. Turn the Rotofast anchor counter-clockwise (left) while ﬁrmly pushing the panel toward the wall. Note: fully engage the installation tool with the metal insert before turning. Remove the painters tape. Using the installation tool, lightly rub the weave of the fabric to close the hole. STEP 7 STEP 8 Rotofast Incorporated 70 Milton Street Sydney, Nova Scotia Canada B1P 4L8 Toll Free - USA & Canada 1-888-545-7444 International 00-1-902-578-2534 Fax 1-902-562-8121 Email [email protected] Website www.rotofast.com

Step-by-Step Rotofast Installation Standard AnchorRemove the painters tape. Using the installation tool, lightly rub the weave of the fabric to close the hole. STEP 7 STEP 8 Rotofast

Download PDF Report

Upload
others
View
2
Download
0

Embed Size (px)

Citation preview

Page 1: Step-by-Step Rotofast Installation Standard AnchorRemove the painters tape. Using the installation tool, lightly rub the weave of the fabric to close the hole. STEP 7 STEP 8 Rotofast

R OTO FA ST.CO M

Measure and mark the location where panel will be placed and mark the orientation on the back of the panel.

Push the scratch awl though the panel at the marked locations, keeping the scratch awl as straight as possible.

Place painters tape on the face of the panel at the desiredanchor locations.

Place panel at marked location and use scratch awl to penetrate panel and mark substrate for anchor locations.(For harder surfaces insert a nail into the hole and tap with a hammer to mark the substrate)

STEP 3

STEP 2

STEP 4

Screw Rotofast Standard Anchor to wall at marked location. Make sure the anchor spins on the shaft of the screw but does not wobble.

Flip arm and push hex insert firmly into center of the anchor.

STEP 5 STEP 6

Rotofast Standard Anchors are a secure and fast solution for acoustical panel installation. See rotofast.com for the Rotofast Standard Anchor installation video.

Step-by-Step Installation

(RST3) Rotofasttm Standard Anchor

1BSTEP 1A

Insert the installation tool through hole in painters tape. Feel and hear the installation tool engage with the insert. Turn the Rotofast anchor counter-clockwise (left) while firmly pushing the panel toward the wall.

Note: fully engage the installation tool with the metal insert before turning.

Remove the painters tape. Using the installation tool, lightly rub the weave of the fabric to close the hole.

STEP 7 STEP 8

Rotofast Incorporated

70 Milton StreetSydney, Nova ScotiaCanada B1P 4L8

Toll Free - USA & Canada1-888-545-7444

International00-1-902-578-2534

Fax1-902-562-8121

[email protected]

Websitewww.rotofast.com