Upload
hahuong
View
247
Download
1
Embed Size (px)
Citation preview
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
1
Part No 98TF07MA4001 Revision 100 Station
Product Name Rugged Tablet PC Model Name M700DM4
Product Name:Rugged Tablet PC
Model Name: M700DM4
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
2
Document History
Item Date Revision Page Description
1 2014/11/30 100 N/A New Document Released
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Approved by Revised by Made by
Brain John Justin
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
3
Table of Contents
Block Diagram ........................................................................................................................................ 4
Notes & Tools ......................................................................................................................................... 5
Version Control Table ............................................................................................................................. 6
Panel & Touch Assembly ........................................................................................................................ 7
Panel Assembly ...................................................................................................................................... 8
Middle Plate assembly ........................................................................................................................... 9
Wi‐Fi antenna Assembly ...................................................................................................................... 10
CPU Board Assembly ............................................................................................................................ 11
IO Board Assembly ............................................................................................................................... 12
Back Cover Assembly ........................................................................................................................... 15
LTE Antenna Assembly ......................................................................................................................... 16
LTE Card assembly ................................................................................................................................ 17
Cover Assembly .................................................................................................................................... 18
Battery pack ......................................................................................................................................... 19
Test Flow Chart .................................................................................................................................... 20
LED & Button Test ................................................................................................................................ 21
LCD & I/O Test ...................................................................................................................................... 22
Sensor Test ........................................................................................................................................... 24
GPS Test ................................................................................................................................................ 25
RF Test .................................................................................................................................................. 26
Battery Test .......................................................................................................................................... 27
Camera Test .......................................................................................................................................... 28
Six‐Sided Figure .................................................................................................................................... 29
Packing Assembly ................................................................................................................................. 30
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
4
Model 98TF07MA4001 Revision 100 Station
Operation Name Block Diagram Remark
M700DM4-200 IO Board
90IOM7DT4102
Adapter 5V 15W 2.5ψ 9226015W05V1
MK8-200 CPU Board 90MBMK802000
M7T4IC-110 Camera Bridge 90BB7T4IC100
M7T4IK-100 Key Pad Board 90BB7T4IK000
Camera w/o LED 9B000000000H
P-Cap Touch EP0700MLS3TXCP0700MLS3
Wi-Fi Antenna 39700010000I
Panel 1024*600 500nit 111H0700EG00
4G LTE WWAN Card 9B000000004E
M7T4IM-100 Machine Pin90BB7T4IM000
M7T4IL-100 LED Board 90BB7T4IL000
GPS Antenna 397000000005
94DG12G120A0
94DG12G120B2
Battery 3.7V 5300mAh 320403704005
LED Board for Camera 9B000000000S
LTE MAIN Antenna 39700030001A
LTE AUX Antenna 39700030001B
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
5
Part No 98TF07MA4001 Revision 100 Station
Operation Name Notes & Tools Remark
ATTENTION: Remarks
1. Please put on a pair white ESD glove when working.
2. Please put on the ESD belt when working.
3. Pay attention to the torque of electric screw driver.
4. Make sure all screws are tight without loose.
5. No thread stripped happen.
Tools: Remarks
1. Electric Screwdriver (refer to MIPD015 Electric Screwdriver Torque
Calibration Standard Procedure)
2. White ESD glove
3. ESD belt
4. Hot Glue Gun
Note: Remarks
Please refer to the detailed BOM (include BIOS & Recovery CD) from the
EIP system.
Use Nylon screws or dispensers when assembling.
Use hot glue gun to connect all junctions precisely.
Expendables: Remarks
MIPD015 Electric Screwdriver Torque Calibration Standard Procedure
MIPDXXX Board Gluing Standard Operating Procedure
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
6
Part No 98TF07MA4001 Revision 100 Station
Operation Name Version Control Table Remark
Item Device Part Number Model Name Firmware
Version
HW
CPU Board 90MBMK802000 MK8 V200
IO Board 90IOM7DT4102 M700DM4 V200
Camera Bridge
Board 90BB7T4IC100 M7T4IC V110
Key PAD Board 90BB7T4IK000 M7T4IK V100
LED Board 90BB7T4IL000 M7T4IL V100
Machine Pin Board 90BB7T4IM000 M7T4IM V100
Panel 111H0700EG00 FG07W0DSSWAGL1
Touch TXCP0700MLS3 EP0700MLS3
ME
Front Cover 90ME02000039 V100
Rear Cover 88070T044201 V120
Middle Plate 82W70A11T500 V150
IO Cover 88070T261204 V100
SW
Android Version 4.2.1
Baseband Version SWI9X15C_05.05.16.00 r21040
carmd‐fwbuild1
Kernel Version 3.4.5
Ryan1@SW110 #9
Build number ALPS.W10.24.p0
Custom build
Version M700DM4_SIERRA_HWV1.3_v141125
Accessory
Battery 320403704005
Adapter 9226015W05V1 3A‐182WP05
Adapter 604610606004 Europe Standard
Camera 9B000000000H
LED for Camera 9B000000000S
LTE WWAN Card 9B000000004E MC7304 05.05.16.00 Generic
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
7
Part No 98TF07MA4001 Revision 100 Station
Operation Name Panel & Touch Assembly Remark
Item Material:
A 90ME02000039
B 9117070K8000
C TXCP0700MLS3
Step Assembly Description:
1
Remove paper on the adhesive tape then
unite the Plastic cover (A) onto the Frame
(B)
2 Affixed the Touch(C) onto the Front Cover
carefully.
3 Protect the Touch sensor using insulating
tape.
Item Tools:
1 Insulating tape
Item Note:
1
STEP 3
STEP 1
A B
STEP 2
C
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
8
Part No 98TF07MA4001 Revision 100 Station
Operation Name Panel Assembly Remark
Item Material:
A 111H0700EG00
Steps Assembly Description:
1
Using W2xH0.5mm double sided adhesive
tape stick the Panel (A) around its four
sides.
2 Make sure to protect Panel cable using
insulating tape.
3
On the Panel laminated strip on the back,
measure the outer edge and stick using
W3xH0.5mm double sided foam tape. Do
not stick on the area (Marked in yellow) to
avoid over voltage.
4 Fix the Panel on the Front Cover
Item Tools:
1 Insulating Tape
2 W2xH0.5mm Double sided foam
3 W3xH0.5mm Double sided adhesive tape
Item Note:
1
Make sure to keep the area clean
between Panel and Touch while
attaching them together.
STEP 3
STEP 3, 4
STEP 1, 2
A
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
9
Part No 98TF07MA4001 Revision 100 Station
Operation Name Middle Plate assembly Remark
Item Material:
A 90BB7T4IK000
B 90BB7T4IL000
C 9156070K9F00
D 82W70A11T500
E 9128070K1100
Item Assembly Description:
1 Put on the Dome of the Button(C) into the
Key Pad plate(A)
2 Fix the LED plate (B) use Philips pan
screw M2 x4mm to lock the front frame.
3 Fix the Key Pad switch board into the front
frame
4
Use Philips pan screw M2x4mm(marked in
blue circle) )and Philips pan screw
M2.5x4mm(marked in green circle)and
lock the partition Middle plate(D)
5 Place the water proof O-RING (E) into the
front frame.
Item Tools:
1 Philips Pan Screw M2x4mm
2 Philips Pan Screw M2.5x4mm
Item Note:
1
STEP 1
A C
STEP 2, 3
B
STEP 4, 5
D E
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
10
Part No 98TF07MA4001 Revision 100 Station
Operation Name Wi‐Fi antenna Assembly Remark
Item Material:
A 39700010000I
Steps Assembly Description:
1
Fix the Wi-Fi antenna (A) to the front
frame, the copper foil must affixed into the
middle plate and follow cable alignment
approximately left direction.
2
Use insulating tape to fix Wi-Fi antenna
cable make sure to follow proper alignment
along the line at the back and not interfere
other cable.
Item Tools:
1 Insulating tape
Item Note:
1 Note the antenna outlet and proper
alignment.
STEP 2
STEP 1
A
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
11
Part No 98TF07MA4001 Revision 100 Station
Operation Name CPU Board Assembly Remark
Item Material:
A 60ZZ60500000
B 90MBMK802000
Steps Assembly description:
1 Set up to stick on the back, the Absorbing
material (A) from the CPU Board(B)
2
On the front part of absorbing material,
must temporary not to post on the CPU
Board
Item Tools:
1
Item Note:
1
STEP 2
STEP 1
A
B
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
12
Part No 98TF07MA4001 Revision 100 Station
Operation Name IO Board Assembly Remark
Item Material:
A 90IOM7DT4102
B 9117070K9106
C 94DG12G120A0
D 94DG12G120B2
Steps Assembly Description:
1
Use Philips Screw M1.6x3mm(marked in
green circle) into CPU Board to lock IO
Board(A)
2 Cover up Rubber sponge onto Battery
Connector (marked in yellow)
3 The 12 pin point out FFC(C) connect to
CN1
4 The 12 pin on the other side
FFC(E)connect to CN4
5
IO shown in the figure (marked in red box)
stick W8xH3mm single sided Adhesive
tape(B)
Item Tools:
1 Philips Screw M1.6x3mm
Item Note:
1
STEP 1, 2
A
STEP 5
B B
STEP 3, 4
C
D
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
13
Part No 98TF07MA4001 Revision 100 Station
Operation Name IO Board Assembly (一) Remark
Item Material:
A 前述半成品
B 90BB7T4IC100
C 9163070K9002
Steps Assembly Description:
1 Connect the Touch Cable to the IO board
2 Connect the Panel Cable to the IO board.
3
Use Philip screw M2.5x4mmm (marked in
green circle) at the IO lock the middle
plate, then Connect FFC Cable and secure
with adhesive tape.
4
Connect the Camera Bridge Cable(B) and
use hot melt glue onto the fixed point, then
along the edge of the CPU Board affixed
GPS conductive fabric +Mylar(C)
Items Tools:
1 Philip Screw M2.5x4mm
2 Hot melt Glue
Items Notes:
1
STEP 3
STEP 1, 2
A
STEP 4
C B
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
14
Part No 98TF07MA4001 Revision 100 Station
Operation Name IO Board Assembly (二) Remark
Items Material:
A 397000000005
B 9B000000000H
C 9B000000000S
Steps Assembly Description:
1
Affixed the conductive sponge to
GPS ,then the wifi antenna must connect to
CPU Board, follow antenna alignment as
shown in the figure (marked in red)
2 The Camera(B)Across LED Board(C)must
installed to IO Board
3
The GPS antenna (A) must connected to
CPU Board then fix antenna location,
follow GPS antenna alignment as shown in
the figure.
item Tools:
1 Insulating tape
Item Note:
1
GPS antenna required along the CPU
Board perimeter routing, not above CPU
Board, do not press on top of the CPU steel
when closing the back cover to prevent
over pressure.
2
The GPS antenna position must
approximately between the 2 screw hole in
the middle position.
STEP 1
STEP 3
A
STEP 2
B
C
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
15
Part No 98TF07MA4001 Revision 100 Station
Operation Name Back Cover Assembly Remark
Items Material:
A 61252000000K
B 88070T044201
C 88070T261204
D 90BB7T4IM000
E 916211109101
Steps Assembly Description:
1 Back Cover(B) Paste SPK with water proof
Fabric E) and fix to IP65 SPK(A)
2 Fix IO cover onto the back cover C)
3 Use black Philip screw M2x4mm (marked
in green circle) to put the Machine Pin
4 Use Water proof glue onto the Machine Pin
to secure wiring hole (marked in red)
Items Tools:
1 Black Philip screw M2x4mm
2 Water Proof Plastic
Items Note:
1
STEP 1
A E
B
D
C
STEP 2, 4
STEP 3
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
16
Part No 98TF07MA4001 Revision 100 Station
Operation Name LTE Antenna Assembly Remark
Items Material:
A 39700030001A
B 39700030001B
C 88070T164211
D 9117070K8001
Steps Assembly Description:
1
The LTE Main antenna (A) containing
copper foil and conductive foam sticker
must attached onto the back Cover then
follow illustrated antenna cable alignment
and secured with insulating tape.
2
The LTE AUX antenna(B) must follow
according to the diagram attached to BR
Cover(C)
3
Use adhesive to fix onto Cover (D) the
LTE AUX w/o antenna BR must attach to
the back cover and fix the alignment.
Items Tools:
1 Tape
Items Note:
1
STEP 1
A
STEP 2
B
C
STEP 3
D
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
17
Part No 98TF07MA4001 Revision 100 Station
Operation Name LTE Card assembly Remark
Items Material:
A 9B000000004E
Steps Assembly Description:
1 Use Philip pan Screw M2x4mm(marked in
red circle)to the LTE Card(A)
2
The LTE AUX antenna guide must attach
the conductive foam toward the bottom of
the separator as shown in the figure.
Item Tools:
1 Philip pan screw M2x4mm
Item Note:
1 The conductive foam must contact the
bottom of the separator.
STEP 1
A
STEP 2
STEP 2
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
18
Part No 98TF07MA4001 Revision 100 Station
Operation Name Cover Assembly Remark
Item Material:
A 88070T161311
Steps Assembly description:
1
The wifi antenna must connect to LTE
MAIN (marked in red box) and other wifi
antenna must connect to LTE AUX
(marked in green box)
2 Connect Machine Pin & SPK alignment. do
not block (marked in orange)Vibrator
3 Use PH dome screw M2.5x5mm (marked
in blue) at lock cover.
4
Use I-head screw M2.5x5mm (marked in
Purple and flathead screw M2.5x7mm
(marked in green) lock BR cover
5 Paste camera Lens(A)and safety stickers
etc.
Items Tools:
1 Philip dome screw M2.5x5mm
2 I -head screw M2.5x5mm
3 Flat head screw M2.5x7mm
Items Note:
1
STEP 1
STEP 2
STEP 3, 4, 5
A
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
19
Part No 98TF07MA4001 Revision 100 Station
Operation Name Battery pack Remark
Item Material:
A 320403704005
B 9128070K9100
Items Assembly Description:
1 The Battery Pack(A) affixed the battery
water proof ring(B)
2 After performing the testing process, Load
the Battery pack.
Item Tools:
1
item Note:
1
STEP 2
STEP 1
A B
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
20
Part No 98TF07MA4001 Revision 100 Station
Operation Name Test Flow Chart Remark
M700DM4 Flow Chart
LED & Button
LCD
I/O
Sensor
RF
Battery
Post Burn in Test
Camera
Burn in
Packing
Testing process Test Items
LED & Button
LED
Power Button
Keypad
Volume +/-
LCD Brightness
I/O
Headset
Speaker
Micro SD
Micro USB (OTG)
Touch
Sensor
G-Sensor
Gyroscope
Light Sensor
Vibrator
RF
GPS
LTE WWAN
Wi-Fi
BT
Battery Battery
Camera Camera
Flash
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
21
Part No 98TF07MA4001 Revision 100 Station
Operation Name LED & Button Test Remark
Steps Testing Description:
1 Check Power & Battery LED
2 Check Power Button
3 Check Keypad
4 Check Volume +/-
Items Judgment Standard:
1 Power & Battery LED must function
properly.
2 Power Button must function properly
3 Keypad must respond accurately.
4 Volume +/- Must adjust volume properly.
Items Tools:
1
Item Note:
1
Power Key
Press 2S Turn on
<1 Second Suspend
Resume
Long pressed
<8 second>
Forced to
Shutdown
Led Status
Battery Only Battery + DC in
ON
100%-21%: Not Bright 100% : Green light
20%-11%: Red light on 99%-3%: Orange light
10%-3%: Red light flashes
OFF
100%-21%: Not Bright 100% : Green light
20%-11%: Not Bright 99%-3%: Orange light
10%-3%: Not Bright
Power: Single Color
Battery: Dual Color
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
22
Part No 98TF07MA4001 Revision 100 Station
Operation Name LCD & I/O Test Remark
Steps Test Description:
1 Evaluate the brightness adjustment.
2 Use Micro SD 32GB or more then test if it
functions properly.
3 Insert Micro USB to evaluate into PC test
machine.
4 Use Micro USB OTG cable to connect the
mouse.
5 Using Finger separate capacitive stylus and
Touch accessories.
Item Judgment Standard:
1 required at least 425nit brightness
2 Micro SD must read properly
3 PC must able to recognize and transfer file
to the test machine.
4 OTG must function properly.
5 Touch must function properly <need to
touch the correct position>
Item Tools:
1 Brightness
2 32GB above Micro SD
3 Micro USB Cable
4 Micro USB OTG Cable
5 9B0000000326 Capacitive Touch Stylus
Item Note:
1
STEP 1~5
STEP 1~5
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
23
Part No 98TF07MA4001 Revision 100 Station
Operation Name LCD & I/O Test Remark
Steps Testing Description:
1 Perform Z-Device Test
2 Select Headset Audio and video output for
evaluation.
3 Speaker Handset Inspection
Item Judgment Standard :
1 Headset can detect and use properly.
2 Speaker can be used properly
Item Tools:
1 Z-Device Test
Item Note:
1
STEP 1~3
STEP 1~3
Audio and Video Output
Headset Detection
Earpiece
Press Play Sound
Dual‐Tone –Multi‐Frequency Volume
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
24
Part No 98TF07MA4001 Revision 100 Station
Operation Name Sensor Test Remark
Steps Testing Description:
1 Perform Z-Device Test
2 Test Gravity Sensor <G-Sensor>
3 Gyroscope Measurement Inspection
Item Judgment Standard:
1 XYZ axis and movement information must
correct.
2 XYZ angle information must correct.
Item Tools:
1 Z-Device Test
Item Note:
1
STEP 1~3
STEP 1~3
Gravity Sensor
Gravity X
Gravity Y
Gravity Z
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
25
Part No 98TF07MA4001 Revision 100 Station
Operation Name GPS Test Remark
Steps Testing Description:
1 Perform GPS Test APP
2 Record the number of satellite and signal of
strength.
Item Judgment standard:
1 Position required at least 3 or more
-40dB
2 Must attain at least 6 or more satellite
position.
Item Tools:
1 GPS Test
Item Note:
1
STEP 1~2
STEP 1~2
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
26
Part No 98TF07MA4001 Revision 100 Station
Operation Name RF Test Remark
Steps Testing Description:
1 Select and Evaluate WWAN signal strength
in the system.
2 Open Z-Device Test AP, View Wi-Fi signal
strength within 1 meter away.
3 Use Bluetooth headset to play music file
then test within 10 meters away.
Item Judgment Standard:
1 WWAN signal strength must be greater than
-80dBm
2 Wi-Fi signal strength is greater than -75db
AP test
3 Inspect Bluetooth is normal and not
interrupted.
Item Tools:
1 Z-Device Test
Item Note:
1
STEP 1~3
STEP 1~3
Network:
Telecom name:
TW Mobile
Signal Strength:
‐77 dBm 18 asu
Mobile Network Type:
UMTS
Network Connection Info:
Hot Point Address: 00:21:91:f6:9c:95
Hidden SSID: False
IP Address: 192.168.102.152
Connection speed: 65 Mbps
Physical Address: c8:aa:21:35:23:37
Network Id: 0
Rssi: ‐67 db
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
27
Part No 98TF07MA4001 Revision 100 Station
Operation Name Battery Test Remark
Steps Testing Description:
1 Perform Z-Device Test
2 Battery Inspection
Item Judgment Standard:
1 Battery<must discharge in normal and
correct reading.>
Item Tools:
1 Z-Device Test
Item Note:
1
STEP 1~2
Battery Condition: Good
Battery Charge: 70%
Power Supply: AC
Status: True
Max Battery Power: 100%
Charging Status: Charging
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
28
Part No 98TF07MA4001 Revision 100 Station
Operation Name Camera Test Remark
Steps Testing Description:
1 Perform Z-Device Test
2 Main video Camera lens Inspection.
3 Flash analysis
Item Judgment Standard:
1 Camera <Standard use and in right
direction.>
2 Flash<Can open and Close properly>
Item Tools:
1 Z-Device Test
Item Note:
1
STEP 1~3
STEP 1~3
Main Video Camera
Preview Size
Flash
Press to turn on Flash
Flash Mode
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
29
Part No 98TF07MA4001 Revision 100 Station
Operation Name Six‐Sided Figure Remark
1. Front View
2.Back View
3. Top View
4. Bottom View
5. Left View
6. Right View
STANDARD OPERATION PROCEDURE
(DO NOT COPY OR DISTRIBUTE W ITHOUT PERMISSION) FMRD33B
30
Part No 98TF07MA4001 Revision 100 Station
Operation Name Packing Assembly Remark
Item Material:
A 9111070K2004
B 9142070K1003
C 9143070K1003
D 9226015W05V1
Steps Assembly Description::
1 Accessories: Include Adapter (D) and Power
Plug.
2 Wrap the items in ESD bag , put into EPE
Foam(A)Then Place in the box(B)
3 After fitting into the box, affixed the sticker
on the inner box
4
Fix the inner box then place onto the Outer
box(C). Then Paste stickers and relevant
sealing.
Item Tools:
1 Packaging Tape
Item Note:
1
A
B
STEP 1, 2, 3
D
C
STEP 4