ID32 Motherboard User Manual - Winmatedc.winmate.com.tw/_downloadCenter/2017/SBCManual/ID32 SBC Us… · ID32 Motherboard 3.5” Fanless S with Intel ® Atom D2550 1.86 GHz Processor,

ID32 Motherboard 3.5” Fanless SBC with Intel ® Atom D2550 1.86 GHz Processor,

VGA, LVDS, Dual Giga Ethernet, and Mini-PCIe Interface

V200

User Manual Version 1.2

USER MANUAL PREFACE

ID32 MOTHERBOARD II

PREFACE

Copyright Notice

No part of this document may be reproduced, copied, translated, or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the prior written permission of the original manufacturer.

Trademark Acknowledgement

Brand and product names are trademarks or registered trademarks of their respective owners.

Disclaimer

We reserve the right to make changes, without notice, to any product, including circuits and/or software described or contained in this manual in order to improve design and/or performance. We assume no responsibility or liability for the use of the described product(s), conveys no license or title under any patent, copyright, or masks work rights to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Applications that are described in this manual are for illustration purposes only. We make no representation or warranty that such application will be suitable for the specified use without further testing or modification.

Warranty

We warrant that each of its products will be free from material and workmanship defects for a period of one year from the invoice date. (Standard is one year, extended warranty will need to discuss with our sales representatives. If the customer discovers a defect, we will, at its option, repair or replace the defective product at no charge to the customer, provided it is returned during the warranty period of one year, with transportation charges prepaid. The returned product must be properly packaged in its original packaging to obtain warranty service.

If the serial number and the product shipping data differ by over 30 days, the in-warranty service will be made according to the shipping date. In the serial numbers the third and fourth two digits give the year of manufacture, and the fifth digit means the month (e. g., with A for October, B for November and C for December).

For example, the serial number 1W16Axxxxxxxx means October of year 2016.

USER MANUAL PREFACE

ID32 MOTHERBOARD III

Packing List

Before using this Motherboard, please make sure that all the items listed below are present in your package:

ID32 Motherboard User Manual User’s Manual & Driver CD

If any of these items are missing or damaged, contact your distributor or sales representative immediately.

Customer Service

We provide a service guide as below for any problem by the following steps: First, contact your distributor, sales representative, or our customer service center for technical support if you need additional assistance.

You need to prepare the following information before you call:

Product serial number Peripheral attachments Software (OS, version, application software, etc.) Detailed problem description The exact wording of any error messages In addition, free technical support is available from our engineers every business day. We are always ready to give advice on application requirements or specific information on the installation and operation of any of our products. Please do not hesitate to call or e-mail us.

USER MANUAL PREFACE

ID32 MOTHERBOARD IV

Advisory Conventions

Four types of advisories are used throughout the user manual to provide helpful

information or to alert you to the potential for hardware damage or personal injury.

These are Notes, Important, Cautions, and Warnings. The following is an example of

each type of advisory.

NOTE:

A note is used to emphasize helpful information

IMPORTANT:

An important note indicates information that is important for you to

know.

CAUTION

A Caution alert indicates potential damage to hardware and explains how to

avoid the potential problem.

WARNING!

An Electrical Shock Warning indicates the potential harm from electrical

hazards and how to avoid the potential problem.

USER MANUAL PREFACE

ID32 MOTHERBOARD V

Safety Precautions

CAUTION

Always ground yourself to remove any static charge before touching the

CPU card. Modern electronic devices are very sensitive to static electric

charges. As a safety precaution, use a grounding wrist strap at all times.

Place all electronic components in a static-dissipative surface or

static-shielded bag when they are not in the chassis.

Safety and Warranty

1. Please read these safety instructions carefully.

2. Please keep this user manual for later reference.

3. Please disconnect this equipment from any AC outlet before cleaning. Do not use

liquid or spray detergents for cleaning. Use a damp cloth.

4. For pluggable equipment, the power outlet must be installed near the equipment

and must be easily accessible.

5. Keep this equipment away from humidity.

6. Put this equipment on a reliable surface during installation. Dropping it or letting it

fall could cause damage.

7. Make sure the voltage of the power source is correct before connecting the

equipment to the power outlet.

8. Position the power cord so that people cannot step on it. Do not place anything

over the power cord.

9. All cautions and warnings on the equipment should be noted.

10. If the equipment is not used for a long time, disconnect it from the power source to

avoid damage by transient over-voltage.

11. If any of the following situations arises, get the equipment checked by service

personnel:

A. The power cord or plug is damaged.

B. Liquid has penetrated into the equipment.

C. The equipment has been exposed to moisture.

D. The equipment does not work well, or you cannot get it to work according to

the user’s manual.

E. The equipment has been dropped and damaged.

F. The equipment has obvious signs of breakage.

USER MANUAL ABOUT THIS USER MANUAL

ABOUT THIS USER MANUAL

This User Manual provides information about using the ID32 Motherboard. The

documentation set for the ID32 Motherboard provides information for specific user

needs, and includes:

ID32 Motherboard User Manual – contains detailed description on how to use

the motherboard, its components and features.

NOTE:

Some pictures in this guide are samples and can differ from actual

product.

Document Revision History

Version Date Note

1.0 27-Aug-2012 Initial release

1.1 7-May-2015 Content revision

1.2 21-Mar-2017 Update BIOS settings

USER MANUAL CONTENTS

CONTENTS

PREFACE ....................................................................................................................................................I

ABOUT THIS USER MANUAL ......................................................................................................................I

CHAPTER 1: GENERAL INFORMATION ....................................................................................................... 2

1.1 INTRODUCTION ......................................................................................................................................... 2

1.2 FEATURES ............................................................................................................................................. 2

1.3 MOTHERBOARD SPECIFICATIONS ................................................................................................................... 3

1.4 FUNCTIONAL DESCRIPTION .......................................................................................................................... 5

1.5 PHYSICAL DESCRIPTION ............................................................................................................................... 6

CHAPTER 2: HARDWARE INSTALLATION .................................................................................................... 8

2.1 MOTHERBOARD COMPONENTS ..................................................................................................................... 8

2.1.1 Top ................................................................................................................................................ 8

2.1.2 Bottom .......................................................................................................................................... 9

2.2 MEMORY MODULE (SO-DIMM) INSTALLATION ............................................................................................ 10

2.3 I/O EQUIPMENT INSTALLATION ................................................................................................................... 11

2.3.1 12V DC-IN .................................................................................................................................... 11

2.3.2 Serial COM Ports ......................................................................................................................... 11

2.3.3 External VGA ............................................................................................................................... 11

2.3.4 Ethernet Interface ....................................................................................................................... 11

2.3.5 USB Ports .................................................................................................................................... 11

2.3.6 Audio Function ............................................................................................................................ 12

2.4 JUMPER SETTINGS .................................................................................................................................... 13

2.3.1 Jumper List .................................................................................................................................. 14

2.3.2 Connectors and Pin Assignment .................................................................................................. 17

2.3.3 External Connectors .................................................................................................................... 25

CHAPRTER 3: DRIVER INSTALLATION ....................................................................................................... 28

3.1 CHIPSET DRIVER INSTALLATION ................................................................................................................... 28

3.1.1 Standard CMOS Features ............................................................................................................ 28

3.2 GRAPHIC DRIVER INSTALLATION .................................................................................................................. 31

3.2.1 Standard CMOS Feature.............................................................................................................. 31

3.2.2 Panel Resolution Setting ............................................................................................................. 34

3.3 ETHERNET DRIVER INSTALLATION ................................................................................................................ 37

3.4 AUDIO DRIVER INSTALLATION ..................................................................................................................... 40

3.5 FINTEK COM PORT DRIVER INSTALLATION .................................................................................................... 42

USER MANUAL CONTENTS

ID32 MOTHERBOARD II

CHAPTER 4: AMI BIOS SETUP .................................................................................................................. 46

4.1 HOW AND WHEN TO USE BIOS SETUP ........................................................................................................ 46

4.2 BIOS FUNCTIONS .................................................................................................................................... 48

4.2.1 Main Menu ................................................................................................................................. 48

4.2.2 ADVANCED MENU ................................................................................................................................ 50

4.2.2.1 PCI Subsystem Settings ............................................................................................................ 52

4.2.2.2 ACPI Settings ............................................................................................................................ 54

4.2.2.3 S5 RTC Wake Settings ............................................................................................................... 55

4.2.2.4 CPU Configuration ................................................................................................................... 56

4.2.2.5 IDE Configuration ..................................................................................................................... 57

4.2.2.6 Intel Fast Flash Standby ........................................................................................................... 59

4.2.2.7 USB Configuration .................................................................................................................... 60

4.2.2.8 F81865 Super IO Configuration ................................................................................................ 62

4.2.2.9 F81865 H/W Monitor ............................................................................................................... 64

4.2.2.10 PPM Configuration ................................................................................................................. 65

4.3 CHIPSET ................................................................................................................................................. 66

4.3.1 Memory Frequency Timing ......................................................................................................... 66

4.3.2 Intel IGD Configuration ............................................................................................................... 67

4.4 BOOT .................................................................................................................................................... 68

4.4 SECURITY ............................................................................................................................................... 72

4.5 SAVE & EXIT ........................................................................................................................................... 74

CHAPTER 5: TECHNICAL SUPPORT ........................................................................................................... 77

APPENDIX A: DIGITAL I/O SAMPLE CODE ................................................................................................ 78

APPENDIX B: WATCHDOG SAMPLE CODE ................................................................................................ 81

USER MANUAL CHAPTER 1 GENERAL INFORMATION

ID32 MOTHERBOARD 1

GENERAL INFORMATION This chapter includes the ID32 Motherboard background information.


ID32 MOTHERBOARD 2

CHAPTER 1: GENERAL INFORMATION

This chapter includes the ID32 Motherboard background information.

1.1 Introduction

Thank you for choosing the ID32 Motherboard. The ID32 SBC is integrated with Intel®

NM10 express chipset, 17x17mm, and Atom D2550 Processor. Intel Atom Processor with

32nm low power design enables down to 50% less average power consumption and the

chipset delivers up to 4x improvement in graphics performance and enables up to 50%

higher data transfer bus speed rate.

In peripheral connectivity, ID32 SBC features with Mini-PCIe I/O ports, one Serial ATA

connectors, four Serial Port (One Connector; Three Pin Header ) and Six Hi-Speed USB

2.0 connectors( Two Connector ; Four Pin Header ) .Additionally, ID32 SBC build-in a 12V

DC-IN power adapter.

Thus, the ID32 SBC is designed to satisfy most of the applications in the industrial

computer market, such as Gaming, POS, KIOSK, Industrial Automation, and

Programmable Control System. It is a compact design to meet the demanding

performance requirements of today’s business and industrial applications.

1.2 Features

ID32 Motherboard features:

3.5-inch Form Factor ( 146mm x 102mm)

Supports Intel® Atom D2550 1.86GHz processor

System memory up to 4GB DDR3 800/1066, SO-DIMM

Intel ®NM10 Chipset

Intel® Graphic Accelerator 3650 Integrated Graphics Engine

Dual Broadcom BCM57780 GbE controller

2 x Mini PCIe(one for wireless, one for SATA SSD), 4 X COM, 6 x USB2.0, 1 x SATA, 8 x

GPIO ports, 1 xDVI


ID32 MOTHERBOARD 3

1.3 Motherboard Specifications

Model Name ID32

System

Specifications

CPU Type Intel® Atom™ Dual Core D2550

CPU Speed 2.13 GHz

Chipset Intel® NM10

BIOS AMI 16Mbit Flash

Super I/O

Chipset Fintek F81865

Graphic Intel® Graphic Accelerator 3600 support DX9,

OGL3.0

System

Memory DDR3 800/1066 MHz SO-DIMM Slot, Max. 4GB

USB 6 ports, USB 2.0 (2 x USB Connector, 4 x USB

pin-header )

Display

Specifications

LCD Interface Single-channel 24 bit LVDS Up to 1440 x 900 @

60Hz

Graphic

Resolution

VGA Mode : Up to 1920 x 1200 @ 60Hz

DVI : 1920 x 1200 @ 60Hz

Multiple

Display Dual display

Audio Codec Realtek ALC886 HD Audio Codec

Audio Interface Line-in, Line-out, Mic in

Ethernet

LAN Dual Broadcom BCM57780 GbE controller

Ethernet

Interface 1000 Base-Tx Gigabit Ethernet Compatible

I/O

Connectors

Rear I/O

2 x RJ-45

1 x RS232/422/485

2 x USB 2.0

1 x VGA

1 x DC-in Power Jack (+12V)

Internal I/O

3 x RS-232 by pin-header

4 x USB 2.0 by pin-header

1 x SATA II

1 x Digital I/O ( 8 ports GPIO)

1 x Power-input 2-pin connector

1 x DVI (support DL240D converter board)


ID32 MOTHERBOARD 4

Expansion Slot 1 x Mini PCIe slot (for wireless module)

1 x Mini PCIe slot (for SATA SSD)

Mechanical

Specifications

Dimensions

(W x L) 146 mm x 101 mm (3.5" Form Factor)

Environment

Considerations

Operating

Temp. -20 deg. C to 60 deg. C

Storage Temp. -40 deg .C to 70 deg. C

Operating

Humidity 10~95% RH@400C, non-condensing

Power

Management

Power Input 12V DC-IN Power Jack

Power

Consumption 11.5W (D2550+NM10)

Packing List Standard

ID32 Motherboard

ID32 SBC Use Manual V1.0

ID32 Manual & Driver CD V1.0

OS Support Windows 7 Embedded

Windows XP Embedded


ID32 MOTHERBOARD 5

1.4 Functional Description

Function block (V200)


ID32 MOTHERBOARD 6

1.5 Physical Description

Board Dimensions (V200)

USER MANUAL CHAPTER 2 HARDWARE INSTALLATION

ID32 MOTHERBOARD 7

HARDWARE INSTALLATION This chapter provides information on how to use

jumpers and connectors on the ID32 motherboard.


ID32 MOTHERBOARD 8

CHAPTER 2: HARDWARE INSTALLATION

This chapter provides information on how to use jumpers and connectors on the

IV70 Motherboard. Be cautious while working with these modules. Carefully read the

content of this chapter in order to avoid any damages.

2.1 Motherboard Components

2.1.1 Top


ID32 MOTHERBOARD 9

2.1.2 Bottom


ID32 MOTHERBOARD 10

2.2 Memory Module (SO-DIMM) Installation

The ID32 Motherboard provides one 204-pin SODIMM slot. The socket supports up

to 4GB DDR3 1066 SDRAM.

When installing the –memory unit, please follow the steps below:

1. Firmly insert the SO-DIMM at an angle of about 30-degree into the slot. Align the

SO-DIMM with the slot until it is fully inserted. The notch on the SO-DIMM should

match the break on the slot.

2. Press downwards on SO-DIMM until the retaining clips at both ends fully snap

closed and the SO-DIMM is properly seated.

CAUTION

The SO-DIMM only fits in one correct orientation. It will cause

permanent damage to the development board and the SO-DIMM if the

SO-DIMM is forced into the slot at the incorrect orientation.


ID32 MOTHERBOARD 11

2.3 I/O Equipment Installation

2.3.1 12V DC-IN

The Motherboard allows plugging 12V DC-IN jack on the board without another

power module converter under power consumption by Intel Atom D2550 1.86GHz

Processor in NM10 chipset.

*Without power/reset OSD, you can short circuit pin5 & 6 of the onboard panel

connector to boot up the motherboard.

2.3.2 Serial COM Ports

Two RS-232 connectors build in the rear I/O. One optional COM ports support

RS-422/485. When an optional touch-screen is ordered with PPC, serial com port can

connect to a serial or an optional touch-screen.

2.3.3 External VGA

The Motherboard has one VGA port that can be connected to an external CRT/ LCD

monitor. Use VGA cable to connect to an external CRT / LCD monitor, and connect

the power cable to the outlet. The VGA connector is a standard 15-pin D-SUB

connector.

2.3.4 Ethernet Interface

The Motherboard is equipped with Broadcom BCM57780 chipset which is fully

compliant with the PCI 10/100/1000 Mbps Ethernet protocol compatible. It is

supported by major network operating systems. The Ethernet ports provide two

standard RJ-45 jacks.

2.3.5 USB Ports

Four USB devices (Two with pin headers) may be connected to the system though an

adapter cable. Various adapters may come with USB ports. USB usually connect the

external system to the system. The USB ports support hot plug-in connection.

Whatever, you should install the device driver before you use the device.


ID32 MOTHERBOARD 12

2.3.6 Audio Function

The Audio 7.1 channel capabilities are provided by a Realtek ALC886 chipset

supporting digital audio outputs. The audio interface includes two jacks: line-in and

line-out.


ID32 MOTHERBOARD 13

2.4 Jumper Settings

This section explains how to set jumpers for correct configuration of the

motherboard.

NOTE:

A pair of needle nose pliers may be helpful when working with

jumpers. If you have any doubts about the best hardware

configuration for your application, contact your local distributor or

sales representative before you make any changes. Generally, you

simply need a standard cable to make most connections.

The jumper setting diagram is shown below. When the jumper cap is placed on both

pins, the jumper is SHORT. The illustration below shows a 3-pin jumper; pins 1 and 2

are short. If you remove the jumper cap, the jumper is OPEN.

PIN 1-2 SHORT

PIN 3 OPEN

CAUTION

To avoid damaging the module, always turn off the power supply

before setting jumpers or clearing CMOS.


ID32 MOTHERBOARD 14

2.3.1 Jumper List

The following tables list the function of each of the board's jumpers.

Label Function Note

CON2 LVDS VOLTAGE 2x3 header , pitch 2.0mm

JP2 RS232 / RS422 / RS485 Selector 2x3 header , pitch 2.0mm

JP3 RS232 / RS422 / RS485 Selector 3x4 header , pitch 2.0mm

JP4 Clear CMOS 3x1 header , pitch 2.0mm

JP5 Backlight Power Voltage Selector 3x1 header , pitch 2.0mm

JP6, 8 Backlight Adjust Mode Selector 3x1 header , pitch 2.0mm

JP7 Backlight Brightness Voltage Selector 3x1 header , pitch 2.0mm

JP9 Backlight Power ON/OFF Selector 3x1 header , pitch 2.0mm

2.3.1.1 CON2: LVDS VOLTAGE

2.3.1.2 JP2, JP3: RS232 / RS422 / RS485 Selector

The jumper can be configured to operate COM1 in RS-232/422/485 mode.

Pin № Function

1-2

(Default

RS232

3-4 RS422

5-6 RS485


ID32 MOTHERBOARD 15

2.3.1.3 JP4:Clear CMOS

Remember to set jumper back to Normal before turning on the power supply.

CAUTION

TURN OFF the power supply before setting Clear CMOS.

2.3.1.4 JP5: Backlight Power Voltage Selector

JP5 can be configured to operate in 5Volts / 12Volts mode.

2.3.1.5 JP6, JP8 Backlight Adjust Mode Selector

Location DC mode

(For HW)

PWM mode

(For BIOS)

DC mode

(For BIOS)

JP6 1-2 2-3 2-3

JP8 X X 1-2

2.3.1.6 JP7: Backlight Brightness Voltage Selector

Pin № Function

1-2 Clear CMOS

2-3 (Default) Normal

Pin № Function

1-2 +5V

2-3 (Default) +12V

Pin № Function

1-2 +3.3V

2-3 (Default) +5V


ID32 MOTHERBOARD 16

2.3.1.7 JP9: Backlight Power ON/OFF Selector

2.1.3.8 VRD Select Backlight Adjust Mode

Pin № Function

1-2 +5V

2-3 (Default) +12V

Location VR→PWM OSD→PWM DC mode

JP6 X X 1-2

JP8 2-3 2-3 2-3

JP10 1-2 X X


ID32 MOTHERBOARD 17

2.3.2 Connectors and Pin Assignment

The table below lists the function of each of the board’s connectors.

Label Function Note

AUDIO1 Audio connector 2x6 header

CN10 12V/5V External Power 4x2 header ,pitch 2.54mm

COM2 COM2 for RS232 2x5 header

COM3(Left) COM3 for RS232 2x5 header

COM4(Right) COM4 for RS232 2x5 header

COM Port COM1 for RS232/422/485 DB9

CON3 Digital Panel Backlight

Inverter Power

7x1 header, pitch 2.54mm

CPU_FAN FAN CONNECTOR 3x1 Pin Header

DC JACK2 12V DC Jack 2 Pin Jack

DIDO1 Digital I/O 2x5 Pin header

DVI1 DVI LCD Output Connector 20DP-1.25V

J2/J3 Amplifier 2 Pin header

JP1 Digital Panel Backlight

Brightness Control

3x1 header, pitch 2.54mm

LVDS1 LVDS LCD Output Connector 20DP-1.25V

PANEL1 System Function Connector 5x2 header ,pitch 2.0mm

VGA VGA Output 15pin VGA

USB1 USB PIN HEADER 4x2 Pin Header

USB3 USB PIN HEADER 4x2 Pin Header

12V1 12V External Power 2x1 header, pitch 2.0mm

5V1 5V External Power 2x1 header, pitch 2.0mm


ID32 MOTHERBOARD 18

2.3.2.1 AUDIO: AUDIO Connector

2.3.2.2 CN10: 12V/5V External Power

12V1 5V CN10

2.3.2.3 COM2/3/4: D-SUB Dual Output

The serial port COM, which is option 1 for RS232 (from 11 pin to 20 pin), is the Winbond I/O serial

port.

Pin № Signal Name Pin № Signal Name

1 AZ_FOUT_R 2 AZ_FOUT_L

3 +5VA 4 AUGND

5 LINE1_R 6 LINE1_L

7 MIC1_R 8 MIC1_L

9 AUGND 10 SW_D

11 SW_B 12 SW_C


1 FK NDCD1 2 FK NDSR1

3 FK NSIN1 4 FK NRTS1

5 FK NSOUT1 6 FK NCTS1

7 FK NDTR1 8 FK NRI1

9 GND 10 GND

11 FK NDCD2 12 FK NDSR2

13 FK NSIN2 14 FK NRTS2

15 FK NSOUT2 16 FK NCTS2

17 FK NDTR2 18 FK NRI2

19 GND 20 GND


ID32 MOTHERBOARD 19

2.3.2.4 CON3: Inverter Power Connector

2.3.2.5 CPU _Fan: FAN CONNECTOR

2.3.2.6 DVI1: DVI LCD Output Connector


1 GND 2 TMDS0-

3 TMDS0+ 4 GND

5 DDC_CLK 6 DDC_DATA

7 GND 8 TMDS1-

9 TMDS1+ 10 GND

11 TMDS2- 12 TMDS2+

13 GND 14 CLK+

15 CLK- 16 HPD2

17 DVI_EXT_5V 18 DVI_EXT_5V

Pin № Signal Name

1 +12V

2 +12V

3 +12V

4 GND

5 Backlight Control

6 GND

7 Backlight EN 5V

Pin № Signal Name

1 GND

2 +12V

3 SENSE


ID32 MOTHERBOARD 20

2.3.2.7 J2, J3: Amplifier

2.3.2.8 JP1: Digital Panel Backlight Brightness Control

Pin № Signal Name

1 5V

2 Backlight control

3 GND


ID32 MOTHERBOARD 21

2.3.2.9 LVDS1: LVDS LCD Output Connector


1 LCDVDD 2 LVDS0_TX0_N

3 LCDVDD 4 LVDS0_TX0_P

5 LCDVDD 6 LVDS0_TX1_N

7 GND 8 LVDS0_TX1_P

9 GND 10 LVDS0_TX2_N

11 GND 12 LVDS0_TX2_P

13 GND 14 LVDS0_CLK_N

15 GND 16 LVDS0_CLK_P









33 GND 34 LVDS1_CLK_N

35 GND 36 LVDS1_CLK_P




ID32 MOTHERBOARD 22

2.3.2.10 PANEL1: Front Panel System Function Connector

2.3.2.11 USB1/ USB3: USB PIN HEADER

2.3.2.12 5V1/12V1/CN10: External Power

12V1 5V1 CN10


1 PW_LED+ 2 HD_LED+

3 PW_LED- 4 HD_LED-

5 PW_BT1 6 RT_BT1

7 PW_BT2 8 RT_BT2

9 RSEV 10 5VSB


1 USB 5V 2 USB 5V

3 USB_P7- 4 USB_P6-

5 USB_P7+ 6 USB_P6+

7 GND 8 GND


ID32 MOTHERBOARD 23

2.3.2.13 Mini PCIe slot for SSD


1 PCIE_WAKE# 2 +3.3V

3 NC 4 GND

5 BT_EN 6 +1.5V

7 CLK_OE# 8 USIM_PWR

9 GND 10 USIM_DATA

11 PCIE_CLKM 12 USIM_CLOCK

13 PCIE_CLKP 14 USIM_RESET

15 GND 16 USIM_VPP

17 NC 18 GND

19 NC 20 Wireless_ENABLE

21 GND 22 PCIE_RESET

23 PCIE_RXM 24 +3.3V

25 PCIE_RXP 26 GND

27 GND 28 +1.5V

29 GND 30 SMB_CLK

31 PCIE_TXM 32 SMB_DATA

33 PCIE_TXP 34 GND

35 GND 36 USB_D-

37 GND 38 USB_D+

39 +3.3V 40 GND

41 +3.3V 42 NC

43 GND 44 NC

45 NC 46 NC

47 NC 48 +1.5V

49 NC 50 GND

51 +3.3V 52 +3.3V


ID32 MOTHERBOARD 24

2.3.2.14 Mini PCIe slot for WLAN


1 PCIE_WAKE# 2 +3.3V

3 NC 4 GND

5 BT_EN 6 +1.5V

7 CLK_OE# 8 USIM_PWR

9 GND 10 USIM_DATA

11 PCIE_CLKM 12 USIM_CLOCK

13 PCIE_CLKP 14 USIM_RESET

15 GND 16 USIM_VPP

17 NC 18 GND

19 NC 20 Wireless_ENABLE

21 GND 22 PCIE_RESET

23 PCIE_RXM 24 +3.3V

25 PCIE_RXP 26 GND

27 GND 28 +1.5V

29 GND 30 SMB_CLK

31 PCIE_TXM 32 SMB_DATA

33 PCIE_TXP 34 GND

35 GND 36 USB_D-

37 GND 38 USB_D+

39 +3.3V 40 GND

41 +3.3V 42 NC

43 GND 44 NC

45 NC 46 NC

47 NC 48 +1.5V

49 NC 50 GND

51 +3.3V 52 +3.3V


ID32 MOTHERBOARD 25

2.3.3 External Connectors

The table below lists the function of each of the board’s connectors to connect

external interfaces.

Label Function Note

CN7 Power input 12V DC Jack

COM RS-232/422/485 DB9

USB USB 2.0 USB A Type

RJ-45 Ethernet RJ-45

VGA VGA Output DB15

2.3.3.1 DC Power Input Connector

Power input is a DC jack power connector that accepts 12V DC input.

2.3.3.2 Serial Interface Connector

The ID32 has one serial port connector to connect your device to external devices

such as mouse, modem or printer. You can configure serial port settings

RS-232/422/485 by jumpers.

*Default setting: RS-232

Pin № Signal Name Pin № Name

1 DC_IN 2 GND

Pin № RS-232 RS-422 RS-485

1 DCD TxD- D-

2 RXD TxD+ D+

3 TXD RxD+ NC

4 DTR RxD- NC

5 GND GND GND

6 DSR NC NC

7 RTS NC NC

8 CTS NC NC

9 RI NC NC


ID32 MOTHERBOARD 26

2.3.3.3 USB Connector

ID32 motherboard has two USB 2.0 connectors. Use USB2.0 connector to connect

external devices such as mouse or keyboard to the device.

2.3.3.4 Ethernet Connector

The ID32 has two RJ45 10/100/1000 Mbps Ethernet interfaces for connecting to the

internet.

2.3.3.5 VGA Output Connector

The ID32 has VGA connector (D-Sub 15pin Female). Use VGA cable to connect the

display to the PC system.


1 +5V 2 Data-

3 Data+ 4 GND


1 TX1+ 2 TX1-

3 TX2+ 4 TX2-

5 TX3+ 6 TX3-

7 TX4+ 8 TX4-


1 RED 2 GREEN

3 BLUE 4 ID2/RES

5 GND 6 GND

7 GND 8 GND

9 KEY/PWR 10 GND

11 ID0/RES 12 ID1/SDA

13 HSync 14 VSync

15 ID3/SCL

USER MANUAL CHAPTER 3 DRIVER INSTALLATION

ID32 MOTHERBOARD 27

DRIVER INSTALLATION This chapter contains driver installation

instructions for ID32 motherboard.


ID32 MOTHERBOARD 28

CHAPRTER 3: DRIVER INSTALLATION

This chapter contains driver installation guide. Follow the instructions below to complete the installation. You will quickly complete the installation.

3.1 Chipset Driver Installation

3.1.1 Standard CMOS Features

1. Insert the CD that comes with the motherboard. Open the file document “Chipset Driver”.

2. Click on “infinst_auto.exe“ to install driver.


ID32 MOTHERBOARD 29

3. Click on “Yes “ to agree with the terms of License.

4. Click on “Next“ to install driver.


ID32 MOTHERBOARD 30

5. Click on “Next“ to install driver.

6. Click on “Yes, I want to restart this computer now“, and the click “Finish” completing chipset driver installation.


ID32 MOTHERBOARD 31

3.2 Graphic Driver Installation

3.2.1 Standard CMOS Feature

The computer is equipped with Intel NM10 Companion Device. The Intel Graphic Drivers should be installed first, and it will enable “Video Controller (VGA compatible). Follow the instructions below to complete the installation. You will quickly complete the installation.

1. Insert the CD that comes with the computer. Open the file document “Graphic Driver”.

2. Click on “setup” to execute the setup.


ID32 MOTHERBOARD 32

3. Click on “Next “to install Driver.

4. Click on “Yes “ to agree with the terms of license.


ID32 MOTHERBOARD 33

5. Click on “Next “ to install Driver.

6. Click on “Next “to install Driver.


ID32 MOTHERBOARD 34

7. Click on “Yes, I want to restart this computer now“ to go on.

3.2.2 Panel Resolution Setting

1. Right-click the desktop, and then click Properties. 2. In the Display Properties dialog box, click the Settings tab.


ID32 MOTHERBOARD 35

3. Click on “Monitor”.

4. Click on “Hide modes that this monitor cannot display” to remove this option.


ID32 MOTHERBOARD 36

5. Click on “Setting”, then could choose 32bit color quality.


ID32 MOTHERBOARD 37

3.3 Ethernet Driver Installation

You must make sure which operating system you are using before installing the Ethernet drivers. Follow instruction below to complete the installation of the Broadcom BCM57780 Gigabit Ethernet controller LAN drivers. You will quickly complete the installation.

1. Right-click the desktop, and then click Properties. 2. In the Other device dialog box, click the Settings tab.


ID32 Motherboard 38

3. Click on “Update Driver” to execute the setup.

4. Click on “Browse my computer for driver software“ to install driver.


ID32 MOTHERBOARD 39

5. Choose the path to install driver.

6. Click “Close“ to finish driver installation.


ID32 MOTHERBOARD 40

3.4 Audio Driver Installation

The ALC888 series are high-performance 7.1+2 Channel High Definition Audio Codecs

providing ten DAC channels that simultaneously support 7.1 sound playback, plus 2

channels of independent stereo sound output (multiple streaming) through the front

panel stereo outputs. The series integrates two stereo ADCs that can support a

stereo microphone, and feature Acoustic Echo Cancellation (AEC), Beam Forming (BF),

and Noise Suppression (NS) technology.

You must confirm which operating system you are using before installing the Audio

drivers.

Follow the steps below to complete the installation of the Realtek ALC655 Audio

drivers.

1. Insert the CD that comes with the motherboard. Open the file document

“alc655_driver” and click on “Vista_Win7_R260.exe” to execute the setup.

2. Click on “Yes“ to install driver.

3. Click on “Yes, I want to restart my computer now” to finish installation.


ID32 MOTHERBOARD 41


ID32 MOTHERBOARD 42

3.5 Fintek COM Port Driver Installation

1. If the system is WIN7 please first close UAC(Refer to “Disabling User Account Control

(UAC) in Windows 7”).

2. Extract the Patch_0408.zip to a folder.

3. Double-click batch file(patch.bat) will install driver.

4. Check driver install success.

Before the update or update fail.

After the update and update success.


ID32 MOTHERBOARD 43

5. You will need to restart your computer for driver install success. Type in this

command from the Run menu:

C:\Windows\System32\UserAccountControlSettings.exe or uac

To turn off UAC, move the slider to the Never notify position, and then click OK. If

you're prompted for an administrator password or confirmation, type the password

or provide confirmation.

To turn UAC back on, move the slider to choose when you want to be notified, and

then click OK. If you're prompted for an administrator password or confirmation,


ID32 MOTHERBOARD 44

type the password or provide confirmation.

You will need to restart your computer for UAC to be turned off.

USER MANUAL CHAPTER 4 AMI BIOS SETUP

ID32 MOTHERBOARD 45

AMI BIOS SETUP This chapter describes the different settings

available in the AMI BIOS that comes with the

board. This chapter offers information on the

Award BIOS installation utility.


ID32 MOTHERBOARD 46

CHAPTER 4: AMI BIOS SETUP

Your computer comes with a hardware configuration program which called BIOS

Setup that allows you to view and set up the system parameters.

The BIOS (Basic Input / Output System) is a layer of the software called ‘firmware’

which translates instructions from software (such as the operating system) into

instructions that allow the computer hardware to understand the software programs.

The BIOS settings also identify installed devices and establish many special features.

4.1 How and When to Use BIOS Setup

To enter the BIOS setup, you need to connect an external USB keyboard, press Del

key when the prompt appears on the screen during start up. The prompt screen

shows only few seconds so need press Del key quickly.

IMPORTANT:

Updated BIOS version may be published after the manual released.

Check the latest version of BIOS on the website.

You may need to run BIOS setup utility for reasons listed below:

1. Error message on screen indicates to check BIOS setup

2. Restoring the factory default settings

3. Modifying the specific hardware specifications

4. Necessity to optimize specifications

BIOS Navigation Keys

The following keys are enabled during POST:

Key Function

Del Enters the BIOS setup menu.

F7

Display the boot menu. Lists all bootable devices that are connected

to the system. With cursor ↑and cursor ↓and by pressing <ENTER>,

select the device used for the boot.

Pause Pressing the [Pause] key stops the POST. Press any other key to

resume the POST.


ID32 MOTHERBOARD 47

The following Keys can be used after entering the BIOS Setup.

Key Function

F1 General Help

F2 Previous Values

F3 Optimized Defaults

F4 Save & Exit

Esc Exit

+/- Change Opt.

Enter Select or execute command

Cursor ↑ Moves to the previous item

Cursor ↓ Goes to the next item

Cursor ← Moves to the previous item

Cursor → Goes to the next item

NOTE:

You can press the F1, F2, F3, F4, –/+, and Esc keys by connecting a

USB keyboard to your computer.

For items marked ► press <Enter> for more options.


ID32 MOTHERBOARD 48

4.2 BIOS Functions

This computer has AMI BIOS built-in and a CMOS SETUP utility that allow users to

configure required settings or to activate certain system features. The follwoing

sections describe the configuration options found in the menu items.

4.2.1 Main Menu

When you enter BIOS setup, the first menu that appears on the screen is the main

menu. It contains the system information including BIOS version, processor RC

version, system language, time, and date.

The Main BIOS setup image has two main frames. The left frame displays all the

options that can be configured. Grayed-out options cannot be configured. On the

contrary, options in blue can be configured. The right frame displays the key legend.

Above the key legend is an area reserved for a text message. When an option is

selected in the left frame, it is highlighted in white. Often a text message will

accompany it.

Immediately after the [DEL] key is pressed during startup, the main BIOS setup menu

appears:


ID32 MOTHERBOARD 49

BIOS Setting Description Setting Option Effect

System Language Displays the

system language.

[English] is set up

by default.

Adjustment of the

language

Set the language in

other language.

The

language in this

device is English.

System Date/Time This is current date

setting. The time is

maintained by the

battery when the

device is turned

off.

Date and time

changes.

Set the date in the

format

[mm/dd/yyyy];

The time in the

format:

[hh/mm/ss]

Access Level The current user

access settings

Changes to the

level of access

Administrator is

set up by the

default


ID32 MOTHERBOARD 50

4.2.2 Advanced Menu

The advanced menu also uses to set configuration of the CPU and other system

devices. There are sub menus on the left frame of the screen.

CAUTION

Handle advanced BIOS settings page with caution. Any changes can

affect the operation of your computer.

Advanced Configuration and Power Interface (ACPI) settings allow to control how the

power switch operates. The power supply can be adjusted for power requirements.

You can use the screen to select options of ACPI configuration. A description of the

selected items will appear on the right side of the screen.


ID32 MOTHERBOARD 51

BIOS Setting Description Setting

Option

Effect

Launch PXE

OpROM

Control Launch PXE

OpROM parameters.

To limit the PXE support

to particular devices, use

the function Use device

for PXE.

Enabled Load PXE Option

ROMs.

*Disabled Ignore all PXE

Option ROMs.

Launch Storage

OpROM

Control Launch Storage

OpROM parameters.

To limit the Storage

support to particular

devices, use the function

Use device for Storage.

Enabled Load Storage

Option ROMs

*Disabled Ignore all Storage

Option ROMs

PCI Subsystem

Settings

Configures PCI Subsystem

settings

Enter Opens submenu

ACPI Settings Configures ACPI settings Enter Opens submenu

S5 RTC Wake

Settings

Configures RTC Wake

parameters

Enter Opens submenu

CPU Configuration Configures CPU settings Enter Opens submenu

IDE Configuration Configures IDE

Parameters

Enter Opens submenu

Intel Fast Flash

Standy

Configures Intel Fast

Flash Standy Parameters

Enter Opens submenu

USB Configuration Configures USB Settings Enter Opens submenu

F81865 Super IO

Configuration

Configures IO settings Enter Opens submenu

F81865 H/W

Monitor

Configures Hardware

Monitor settings

Enter Opens submenu

PPM Configuration Configures PPM settings Enter Opens submenu

*Default


ID32 MOTHERBOARD 52

4.2.2.1 PCI Subsystem Settings

Selects the PCI Option ROM to launch in case Multiple Option ROMs (Legacy ROM

and EFI Compatible ROM) are present.


ID32 MOTHERBOARD 53

*Default


PCI ROM Priority Selects the PCI Option ROM

to launch in case Multiple

Option ROMs

Legacy ROM Launches

Legacy ROM

EFI Compatible

ROM

Launches

EFI

Compatible

ROM

PCI Latency

Timer

Use this function to select

the number of PCI bus clocks

to be used for the PCI latency

timer.

*32/64/96/12

8/160/

192/224/248

Program the

PCI latency

timer to X PCI

bus clocks.

VGA Palette

Snoop

Controls the ability of a

primary PCI VGA controller to

share a common palette

(when a snoop writes cycles)

with an ISA video card.

Enabled

*Disabled

Enables or

Disables this

function

PERR#

Generation

Configure PERR# Generation

Settings

Enabled

*Disabled

Enables or

Disables this

function

SERR#

Generation

Configure SERR# Generation

Settings

Enabled

*Disabled

Enables or

Disables this

function


ID32 MOTHERBOARD 54

4.2.2.2 ACPI Settings

*Default


Option

Effect

Enable ACPI

Auto

Configuration

BIOS ACPI Auto

Configuration

Enable/

*Disable

Enables or Disables

this function

Enable

Hibernation

Control hibernation.

This option may be not

effective with some OS.

Enable/

Disable

Enables or Disables

this function

ACPI Sleep

State

Control ACPI Sleep

State parameters

Suspend

Disable

System ability to

Hibernate (OS/S3

Sleep State)

S1 CPU Stop Clock

*S3 Suspend to RAM

Lock Legacy

Resources

Control Lock Legacy

Resources parameters

Enable/

*Disable

Enables or Disable

Lock of Legacy

Resource.

S3 Video

Repost

Control S3 Video Repost

parameters

Enable/

*Disable

Enables or Disable

S3 Video Repost


ID32 MOTHERBOARD 55

4.2.2.3 S5 RTC Wake Settings

You can use the screen to select options for Super IO Configuration, and change the

value of the option selected. A description of the selected item appears on the right

side of the screen.


Wake system with

Fixed Time

Control System

wake on alarm

event settings

Enable/ *Disable System wake on

alarm event.

When enabled,

System will wake

on the

HR:MIN:SEC

specified

Wake system with

Dynamic Time

Set the system to

wake on the

current time +

increase minute (s)

Enabled/ Set the system

to wake on the

current time +

increase minute

(s).


ID32 MOTHERBOARD 56

4.2.2.4 CPU Configuration


Hyper-Threading Enables for

Windows XP and

Linux (optimized for

Hyper-Threading

Technology) and

Disabled for other

OS (not optimized

for

Hyper-Threading

Technology)

Enable/

Disable

Enables or

disables

Hyper-Threadin

g Technology

Execute Disable Bit Configure Execute

Disable Bit Settings

Enable/

Disable

Enables or

disables Disable

Bit Execution

Limit CPUID

Maximum

Configure Limit

CPUID Maximum

Settings

Enable/

Disable

Enables or

disables Limit

CPUID

Maximum


ID32 MOTHERBOARD 57

4.2.2.5 IDE Configuration

Configure SATA as

Determines how SATA controllers(s) operate. The options are IDE and AHCI.


ID32 MOTHERBOARD 58

4.2.2.5.1 SATA Configuration


SATA Controller (s) SATA Ports (0-3)

Device Names if

Present and

Enabled

Enable/

Disable

Enables or

Disables SATA

Ports

(0-3)

Configure SATA as Allows users to

select mode of

SATA controller(s).

ACHI Work in AHCI

mode of SATA

controller(s)

Port0 Speed Limit Allow users to set

Port0 Speed Limit

No Limit No speed limit

Port1 Speed Limit Allow users to set

Port1 Speed Limit

No Limit No speed limit

SATA Port 0 Allows users to

enable or disable

the SATA Port 0.

Enabled/ Disabled Enable or disable

this function

SATA Port 0 Hot

Plug

Allows users to

enable or disable

the Port 0 Hot


this function


ID32 MOTHERBOARD 59

4.2.2.6 Intel Fast Flash Standby

Plug.

SATA Port 1 Allows users to

enable or disable

the SATA Port 1.


this function

SATA Port 1 Hot

Plug

Allows users to

enable or disable

Port 0 Hot Plug


this function


iFFS Support Control iFFS

Support parameters

Enable/

Disable

Enables or

Disables this

function


ID32 MOTHERBOARD 60

4.2.2.7 USB Configuration


ID32 MOTHERBOARD 61


Legacy USB Support User can enable or

disable USB port.

Disable Will keep USB

devices available

only for EFI

applications.

Enable Enable all the USB

devices

EMCI Hand‐off This is a

workaround for OSs

without ECHI hand‐

off support.

Disable Disables this

function

Enable Enables this

function

USB mass storage

driver support

User can Enable or

disable USB mass

storage driver

support.

Disable Disables this

function

Enable Enables this

function

USB Transfer time‐

out

The time‐out value

for control, bulk,

and interrupt

transfers.

1 Sec

5 Sec

10 Sec

20 Sec

Depends on the

time‐out value

Device Reset time‐

out

USB mass storage

device start unit

command time‐

out.

10 Sec

20 Sec

30 Sec

40 Sec

Depends on the

time‐out value

Device power‐up

delay

Maximum time the

device will take

before it properly

reports itself to the

host controller.

Auto Uses default value:

for a root port it is

100 ms, for a Hub

port the delay is

taken from Hub

descriptor


ID32 MOTHERBOARD 62

4.2.2.8 F81865 Super IO Configuration


ID32 MOTHERBOARD 63


Serial Port 1,2,3

,4,5 Configuration

Set Parameters of

Serial Ports. User

can

Enable/Disable the

serial port and

select optimal

settings for the

super IO Device.

Enabled/ Disabled

Enable or disable

Serial Port (COM)

IO GPI0

Configuration

You can use the

screen to select

options for IO GPI0

Configuration.

A description of

the selected item

appears on the

right side of the

screen. For items

marked with ►,

please press

<Enter> for more

options.

Change the

value of the option

selected.

Watch Dog Time

Select

This watchdog

timer can be used

to monitor system

software

operation

and take

corrective action if

the software fails

to function after

the programmed

period.

1~10 min/

Disabled

Set the time 1~10

min or disable this

function


ID32 MOTHERBOARD 64

4.2.2.9 F81865 H/W Monitor

You can see System temperature, fan speed and other PC Health Status parameters.


ID32 MOTHERBOARD 65

4.2.2.10 PPM Configuration

BIOS

Setting

Description Setting Option Effect

EIST Configure Intel Speed

Step (EIST) parameters

Enabled/

Disabled

Enable or disable Intel

Speed Step (EIST)


ID32 MOTHERBOARD 66

4.3 Chipset

4.3.1 Memory Frequency Timing


ID32 MOTHERBOARD 67

4.3.2 Intel IGD Configuration


ID32 MOTHERBOARD 68

4.4 Boot


Option

Effect

Setup Prompt

Timeout

Number of seconds to

wait for setup activation

key

1~X Set the number of

seconds

Bootup Numlock

State

Select the keyboard

NumLock state

On/

Off

Set the keyboard

NumLock state

parameters

Quiet Boot Configure Quiet Boot

Settings

Enabled/

Disabled

Enables or

disables Quiet

Boot option

Fast Boot

Enables or disables boot

with initialization of a

minimal set of devices

required to launch

active boot option. Has

no effect for BBS boot

options

Enabled/

Disabled

Enables or

disables Fast Boot

option


ID32 MOTHERBOARD 69

VGA Support Configures VGA Support

settings

Auto

Only install Legacy

OpRom with

Legacy OS and

logo would NOT

be shown during

post. Efi driver will

still be installed

with EFi OS.

EFI Driver

USB Support Configures USB Support

settings

Disabled All USB devices

will NOT be

available until

after OS boot

Full Initial All USB devices

will be available in

OS and POST

Partial Initial Specific USB

port/device will

not be available

before OS boot

PS2 Device

Support

Configures PS2 Device

Support settings

Enable/

Disable

If Disabled, PS2

devices will be

skipped

Network Stack

Driver Support

Configures Network

Stack Driver Support

settings

Enable/

Disable

If Disabled,

NetWork Stack

Driver will be

skipped

Gate A20 Active Configures Gate A20

Active settings

Upon

Request

GA20 can be

disabled using

BIOS services

Always

Active

Do not allow

disabling GA20;

this option is

useful when any

RT code is

executed above

1MB

Option ROM

Messages

Set display mode for

Option ROM

Force BIOS/

Keep Current

Set display mode

for Option ROM


ID32 MOTHERBOARD 70

Interrupt 19

Capture

Configures Interrupt 19

Capture settings

Disable Disable this

function

Enable Allows Option

ROMs to trap Int

19

Boot Option 1~3 Set the system Boot

order

UEFI: Built-in

EFI Shell

Set the parameter

for each Boot

Option 1~3

SATA SM:

ADATA XM15

32Gb

Set the parameter

for each Boot

Option 1~3

UEFI: ADATA

USB Flash

Drive 1.00

Set the parameter

for each Boot

Option 1~3

Disabled Disable this

function

Hard Drive BBS

Priorities

Hard Drive BBS

Parameters

Enter Opens sub-menu


ID32 MOTHERBOARD 71

Boot Option

This option shows the priorities of the boot options. User can change the priorities

by selecting the particular boot option. The boot option selected in Boot option #1

will be the first priority, followed by second, third and so on.

Network/Hard Device BBS Priorities

It will list all the Boot options that are configured as Network/Hard Drive. User can

change the priority as similar to the main boot option priorities. The first boot option

will be having top boot priority and will appear at the boot option priorities and boot

order.


ID32 MOTHERBOARD 72

4.4 Security

This section allows you to configure and improve your system and allows you to set

up some system features according to your preference.


Adminisrator

Password

Displays whether

or not an

administrator

password has

been set.

Enter password.

Length 3~20

If only

Administrator’s

password is set,

then this only

limits access to

Setup and is only

asked for when

entering Setup/

User Password

Display whether or

not a user

password has

been set.

Enter password.

Length 3~20

If only User’s

password is set.

Then this is a

power on

password and

must be entered


ID32 MOTHERBOARD 73

to boot or enter

setup. In Setup the

User will have

Administrator

rights

HDD 0: ADATA

XM15 3

Set HDD Security

Configuration

HDD Password Allows Access to

Set, Modify and

Clear Hard Disk

User and Master

Passwords. User

password need to

be installed for

Enabling Security.

Master Password

can be Modified

only when

successfully

unlocked with

Master Password

in POST.


ID32 MOTHERBOARD 74

4.5 Save & Exit


ID32 MOTHERBOARD 75


Save Changes and

Exit

This saves the

changes to the CMOS

and exits the BIOS

Setup program.

<YES> Save changes

Discard Changes

and Exit

This exits the BIOS

Setup without saving

the changes made in

BIOS Setup to the

CMOS.

<YES> Saves the changes

<NO> Return to the BIOS

Setup Main Menu

Save Changes and

Reset

Reset the system after

saving the changes.



Setup Main Menu

Discard Changes

and Reset

Reset system setup

without saving any

changes



Setup Main Menu

Save Changes Save changes done so

far to any of the setup

options.



Setup Main Menu

Discard Changes Discard changes done

so far to any of the

setup options.



Setup Main Menu

Restore Defaults Restore/load default

values for all the

setup options.



Setup Main Menu

Save as User

Defaults

Save the changes

done so far as User

defaults.



Setup Main Menu

Restore User

Defaults

Restore the User

Defaults to all the

setup options.



Setup Main Menu

USER MANUAL CHAPTER 5 TECHNICAL SUPPORT

ID32 MOTHERBOARD 76

TECHNICAL SUPPORT This chapter contains directory to technical

support.

USER MANUAL CHAPTER 5 TECHNICAL SUPPORT

ID32 MOTHERBOARD 77

CHAPTER 5: TECHNICAL SUPPORT

This chapter includes the directory for technical support. Free technical support is

available from our engineers every business day. We are always ready to give advice

on application requirements or specific information on the installation and operation

of any of our products. If any problem occurs immediately contact us.

To find the Drivers and SDK, please refer to the Driver CD that comes in the package

or contact us.

The list of SDK available for ID32 Motherboard:

Item File Type Description

1 SDK Watchdog SDK

2 SDK Digital I/O SDK

USER MANUAL APPENDIX A DIGITAL I/O SAMPLE CODE

ID32 MOTHERBOARD 78

APPENDIX A: DIGITAL I/O SAMPLE CODE

//File of the Main.cpp //=========================================================== //This code is for test IA30 Super I/O. //=========================================================== #include <dos.h> #include <conio.h> #include <stdio.h> #include <stdlib.h> //============================================================ #define W83627EHG_INDEX_PORT 0x2E #define W83627EHG_DATA_PORT 0x2F //============================================================ #define W83627EHG_REG_LD 0x07 //============================================================ #define W83627EHG_UNLOCK 0x87 #define W83627EHG_LOCK 0xAA //============================================================ void ClrKbBuf(void); void Unlock_W83627EHG(void); void Lock_W83627EHG(void); void Set_W83627EHG_Reg(unsigned char,unsigned char); unsigned char Get_W83627EHG_Reg(unsigned char); int main (); //============================================================ int main () { unsigned char ucDO = 0; //data for digital output unsigned char ucDI; //data for digital input unsigned char ucBuf; Set_W83627EHG_Reg(0x07,0x07);//switch to logic device 7 // PIN 121~128 function select // Bit0 = 0 -> Game Port. // = 1 -> GPIO1.


ID32 MOTHERBOARD 79

ucBuf = Get_W83627EHG_Reg(0x29); Set_W83627EHG_Reg(0x29,ucBuf|0x01); // Bit0 = 0 -> GPIO1 is inactive. // Bit1 = 1 -> Activate GPIO1. ucBuf = Get_W83627EHG_Reg(0x30); Set_W83627EHG_Reg(0x30,ucBuf|0x01);//Activate GPIO1 Set_W83627EHG_Reg(0xF0,0x0F);//switch GPIO Input(1)/Output(0) port Set_W83627EHG_Reg(0xF1, 0x00); //clear ucDI = Get_W83627EHG_Reg(0xF1) & 0x0F; ClrKbBuf(); while(1) { ucDO++; Set_W83627EHG_Reg(0xF1, ((ucDO & 0x0F) << 4)); ucBuf = Get_W83627EHG_Reg(0xF1) & 0x0F; if (ucBuf != ucDI) { ucDI = ucBuf; printf("Digital I/O Input Changed. Current Data is 0x%X\n",ucDI); } if (kbhit()) { getch(); break; } delay(500); } return 0; } //============================================================ void ClrKbBuf(void) { while(kbhit()) { getch(); } }


ID32 MOTHERBOARD 80

//---------------------------------------------------------------------------

void Unlock_W83627EHG (void)

{

outportb(W83627EHG_INDEX_PORT, W83627EHG_UNLOCK);

outportb(W83627EHG_INDEX_PORT, W83627EHG_UNLOCK);

}

//============================================================

void Lock_W83627EHG (void)

{

outportb(W83627EHG_INDEX_PORT, W83627EHG_LOCK);

}

//============================================================

void Set_W83627EHG_Reg( unsigned char REG, unsigned char DATA)

{

Unlock_W83627EHG(); outportb(W83627EHG_INDEX_PORT, REG);

outportb(W83627EHG_DATA_PORT, DATA); Lock_W83627EHG();

}

//============================================================

unsigned char Get_W83627EHG_Reg( unsigned char REG)

{

unsigned char Result; Unlock_W83627EHG();

outportb(W83627EHG_INDEX_PORT, REG);

Result = inportb(W83627EHG_DATA_PORT); Lock_W83627EHG();

return Result;

}

//============================================================

USER MANUAL APPENDIX B WATCHDOG SAMPLE CODE

ID32 MOTHERBOARD 81

APPENDIX B: WATCHDOG SAMPLE CODE

//File of the Watchdog.cpp //============================================================ //This Sample code is for Watchdog timer configuration //============================================================ //============================================================ #include <dos.h> #include <conio.h> #include <stdio.h> #include <stdlib.h> //============================================================ #define W83627_INDEX_PORT 0x2E #define W83627_DATA_PORT 0x2F #define W83627_UNLOCK 0x87 #define W83627_LOCK 0xAA //#define Watchdog_timeout 10 //============================================================ void Unlock_W83627(void); void Lock_W83627(void); void Set_W83627_Reg(unsigned char,unsigned char); unsigned char Get_W83627_Reg(unsigned char); //============================================================ int main () { int Watchdog_timeout = 10; printf("Input Watchdog Timer time-out value [0-255] : "); scanf("%d",&Watchdog_timeout); if(Watchdog_timeout <= 0 || Watchdog_timeout > 255) { printf("Time-out value out of range!!\n\n"); printf("Input Watchdog Timer time-out value [0-255] : "); scanf("%d",&Watchdog_timeout);


ID32 MOTHERBOARD 82

} Set_W83627_Reg(0x07,0x08);//switch to logic device 8 Set_W83627_Reg(0x30,0x01);//Activate watchdog Set_W83627_Reg(0xF5,0x06);//Select WDTO# count mode.Second Mode. Set_W83627_Reg(0xF6,Watchdog_timeout); //Set Watch Dog Timer Time-out value //Set_W83627_Reg(0xF7,0xC0); //Clear Watchdog timer event int i = Watchdog_timeout; while(1) { if (kbhit()) { if(getch()==0x1B) //Esc break; else{ i=Watchdog_timeout; //Reset Watchdog timer Set_W83627_Reg(0xF6,Watchdog_timeout); //Set Watch Dog Timer Time-out value } } clrscr(); if(i>0){ i--; printf("After %2d sec reset computer!\n",i); printf("Press any key to reset watchdog timer!\n"); printf("Press [Esc] to exit!\n"); } else

printf("Watchdog timer fail!");

delay(1000); }


ID32 MOTHERBOARD 83

Set_W83627_Reg(0xF6,0); //Disable Watchdog timer

return 0;

}

//---------------------------------------------------------------------------

void Unlock_W83627 (void)

{

outportb(W83627_INDEX_PORT, W83627_UNLOCK); outportb(W83627_INDEX_PORT,

W83627_UNLOCK);

}

//============================================================

void Lock_W83627 (void)

{

outportb(W83627_INDEX_PORT, W83627_LOCK);

}

//============================================================

void Set_W83627_Reg( unsigned char REG, unsigned char DATA)

{

Unlock_W83627(); outportb(W83627_INDEX_PORT, REG);

outportb(W83627_DATA_PORT, DATA); Lock_W83627();

}

//============================================================

unsigned char Get_W83627_Reg( unsigned char REG)

{

unsigned char Result; Unlock_W83627();

outportb(W83627_INDEX_PORT, REG); Result = inportb(W83627_DATA_PORT);

Lock_W83627();

return Result;

}

//============================================================

Documents

ID32 Motherboard User Manual - Winmatedc.winmate.com.tw/_downloadCenter/2017/SBCManual/ID32 SBC Us… · ID32 Motherboard 3.5” Fanless S with Intel ® Atom D2550 1.86 GHz Processor,