Upload
vunguyet
View
235
Download
1
Embed Size (px)
Citation preview
www.amnitec.nl
STAINLESS STEEL EXPANSION JOINT, TYPE ABS
APPLICATIONS
An expansion joint with steel welding ends for applications in mainly heating systems, where a thermal expansion of the piping has to be absorbed. The expansion joint will be delivered pre-stressed, which allows a maximum movement.
TECHNICAL DESCRIPTION
Bellow (1) : AISI 316Ti
Welding ends (2) : Carbon Steel
Outer sleeve (3) : AISI 304
Inner sleeve (4) : AISI 304
DATA TABLE
DN Type
NL Pre-stressed Length
AxialCompression D d
Max.Pressure
Max.Pressure
mm (in.) mm mm mm mm bar/20°C bar/100°C
15(1/2) ABS 151630 210 -30 32 21,3 16 10
20(3/4) ABS 201630 200 -30 38 26,9 16 10
25(1) ABS 251630 215 -30 45 33,7 16 10
32(1.1/4) ABS 321630 225 -30 52 42,8 16 10
40(1.1/2) ABS 401630 220 -30 63 48,3 16 10
50(2) ABS 501644 267 -44 76 60,3 16 10
65(2.1/2”) ABS 651644 247 -44 102 76,1 16 10
*NL = Pre-stressed Length.
NL
23
4
1
d D
All information in this document is without any obligation, specifications subject to change without any notice.
www.amnitec.nl
STAINLESS STEEL EXPANSION JOINT, TYPE ABFT
APPLICATIONS
An expansion joint with female thread socks which guarantee fast and smooth tightening. For applications in mainly heating systems, where a thermal expansion of the piping has to be absorbed. Due to its aesthehic appearance, this expansion joint is widely used in livingrooms, hotelchambers, offices etc. With the help of the limiting-pin, minimum and maximum limits and pretension are observed easily.
TECHNICAL DESCRIPTION
Bellow (1) : AISI 316Ti
Sockets (2) : Carbon Steel
Outer sleeve (3) : Carbon Steel
Inner sleeve (4) : AISI 304
Pin (5) : Carbon Steel
DATA TABLE
DN Type
NLNeutral Length
AxialCompression
AxialExtension D d
Max.Pressure
Max.Pressure
mm (in.) mm mm mm mm R bar/70°C bar/100°C
15(1/2) ABFT 151650 260 -13 +12 35 1/2” 16 10
20(3/4) ABFT 201650 260 -13 +12 42 3/4” 16 10
25(1) ABFT 251650 260 -13 +12 51 1” 16 10
32(1.1/4) ABFT 321650 260 -13 +12 60 1.1/4” 16 10
40(1.1/2) ABFT 401650 260 -13 +12 63 1.1/2” 16 10
50(2) ABFT 501650 260 -13 +12 70 2” 16 10
D
NL
2 314 5
All information in this document is without any obligation, specifications subject to change without any notice.
www.amnitec.nl
STAINLESS STEEL EXPANSION JOINT, TYPE ABSM
APPLICATIONS
An expansion joint with stainless steel press fittings, e.g. Mapress, Xpress, Profipress, Bonfix etc., which guarantee very fast and smooth tightening. For applications in mainly heating systems, where a thermal expansion of the piping has to be absorbed. The expansion joint will be delivered pre-stressed, which allows a maximum movement.
TECHNICAL DESCRIPTION
Bellow (1) : AISI 316Ti
Welding ends (2) : Carbon Steel
Mapress fitting (3) : AISI 316 L
Outer sleeve (4) : AISI 304
Inner sleeve (5) : AISI 304
DATA TABLE
DN Type
NL Pre-stressed Length
AxialCompression D d
Max.Pressure
Max.Pressure
mm (in.) mm mm mm mm bar/20°C bar/100°C
15(1/2) ABSM 151630 280 -30 32 18 16 10
20(3/4) ABSM 201630 284 -30 38 22 16 10
25(1) ABSM 251630 306 -30 45 28 16 10
32(1.1/4) ABSM 321630 327 -30 52 35 16 10
40(1.1/2) ABSM 401630 340 -30 63 42 16 10
50(2) ABSM 501644 387 -44 76 54 16 10
*NL = Pre-stressed Length.
D d
5
1
NL
42 3
All information in this document is without any obligation, specifications subject to change without any notice.
www.amnitec.nl
STAINLESS STEEL EXPANSION JOINT, TYPE ABFTM
APPLICATIONS
An expansion joint with female thread socks and prefab stainless steel press fittings, e.g. Mapress, Xpress, Profipress, Bonfix etc., which guarantee very fast and smooth tightening. For applications in mainly heating systems, where a thermal expansion of the piping has to be absorbed. Due to its aesthehic appearance, this expansion joint is widely used in livingrooms, hotelchambers, offices etc. With the help of the limiting-pin, minimum and maximum limits and pretension are observed easily.
TECHNICAL DESCRIPTION
Bellow (1) : AISI 316Ti
Sockets (2) : Carbon Steel
Outer sleeve (3) : Carbon Steel
Inner sleeve (4) : AISI 304
Pin (5) : Carbon Steel
Mapress-fitting (6) : AISI 316L
DATA TABLE
DN Type
NL Neutral Length
AxialCompression
AxialExtension D d
Max.Pressure
Max.Pressure
mm (in.) mm mm mm mm mm bar/70°C bar/100°C
15(1/2) ABFTM 151650 260 -13 +12 35 18 16 10
20(3/4) ABFTM 201650 260 -13 +12 42 22 16 10
25(1) ABFTM 251650 260 -13 +12 51 28 16 10
32(1.1/4) ABFTM 321650 260 -13 +12 60 35 16 10
40(1.1/2) ABFTM 401650 260 -13 +12 63 42 16 10
50(2) ABFTM 501650 260 -13 +12 70 54 16 10
Dd
NL "A"
TL=NL+2X ’’A’’
"A"2 314 5
6
All information in this document is without any obligation, specifications subject to change without any notice.
’’A’’: Is dependable of the brand Press fitting.
www.amnitec.nl
STAINLESS STEEL EXPANSION JOINT, TYPE ANW
APPLICATIONS
An expansion joint with steel welding ends for applications in mainly heating systems, where a thermal expansion of the piping has to be absorbed. This type of expansion joint has to be welded into the piping system and it is basically meant for axial movements.
TECHNICAL DESCRIPTION
Bellow (1) : AISI 316TiWelding ends (2+3) : Carbon SteelInner sleeve (4, Option) : AISI 304
DATA TABLE
DN Type
NLNeutral Length
AxialCompression
AxialExtension D E
Max.Pressure
Max.Pressure
mm (in.) mm mm mm mm mm bar/20°C bar/100°C
15(1/2) ANW 151620 148 -10 +10 21,3x2,75 27 16 10
20(3/4) ANW 201622 151 -11 +11 26,9x2,75 32 16 10
25(1) ANW 25-16-26 152 -13 +13 33,7x3,25 39 16 10
32(1.1/4) ANW 32-16-26 186 -13 +13 42,4x3,25 46 16 10
40(1.1/2) ANW 40-16-36 202 -18 +18 48,3x3,5 58 16 10
50(2) ANW 50-16-46 224 -23 +23 60,3x4 69 16 10
65(2.1/2) ANW 65-16-48 236 -24 +24 76,1x3,6 87 16 10
80(3) ANW 80-16-40 205 -20 +20 88,9x6,4 104 16 10
100(4) ANW 100-16-40 205 -20 +20 114,3 x4,0 127 16 10
125(5) ANW 125-16-50 210 -25 +25 139,7x4,0 155 16 10
150(6) ANW 150-16-50 265 -25 +25 168,3x4,5 184 16 10
200(8) ANW 200-16-50 276 -25 +25 219,1x6,3 235 16 10
250(10) ANW 250-16-50 305 -25 +25 273x6,3 285 16 10
300(12) ANW 300-16-50 335 -25 +25 323,9x8,0 337 16 10
*For combined movements, consult AmniTec BV.
NL
3 4
12
DE
All information in this document is without any obligation, specifications subject to change without any notice.
www.amnitec.nl
STAINLESS STEEL EXPANSION JOINT, WITH FIXED FLANGES, TYPE ANF
APPLICATIONS
An expansion joint with steel welding ends with steel fixed flanges according to PN10/PN16 (see table) For applications in mainly heating systems, where a thermal expansion of the piping has to be absorbed. This type of expansion joint is basically meant for axial movements. Flanges are mounted in line.
TECHNICAL DESCRIPTION
Bellow (1) : AISI 316TiWelding ends (2) : Carbon SteelFlanges (3) : Carbon SteelInner sleeve (4, Option) : AISI 304
FLANGES
Fixed, PN 16(DN 200 up to DN 300-PN 10), carbon steel. Other flanges (ANSI) on request.
NL
2 4
13
DATA TABLE
DN Type
NLNeutral Length
AxialCompression
AxialExtension
Flangeconnection
Max.Pressure
Max.Pressure
mm (in.) mm mm mm mm bar/20°C bar/100°C
15(1/2) ANF 151620 160 -10 +10 PN 16 16 10
20(3/4) ANF 201622 161 -11 +11 PN 16 16 10
25(1) ANF 251626 162 -13 +13 PN 16 16 10
32(1.1/4) ANF 321626 196 -13 +13 PN 16 16 10
40(1.1/2) ANF 401636 212 -18 +18 PN 16 16 10
50(2) ANF 501646 234 -23 +23 PN 16 16 10
65(2.1/2) ANF 651648 246 -24 +24 PN 16 16 10
80(3) ANF 801640 215 -20 +20 PN 16 16 10
100(4) ANF 1001640 215 -20 +20 PN 16 16 10
125(5) ANF 1251650 220 -25 +25 PN 16 16 10
150(6) ANF 1501650 275 -25 +25 PN 16 16 10
200(8) ANF 2001650 286 -25 +25 PN 10 16 10
250(10) ANF 2501650 315 -25 +25 PN 10 16 10
300(12) ANF 3001650 345 -25 +25 PN 10 16 10
*For combined movements, consult AmniTec BV.
All information in this document is without any obligation, specifications subject to change without any notice.
www.amnitec.nl
STAINLESS STEEL EXPANSION JOINT,WITH SWIVEL FLANGES, TYPE ANL
APPLICATIONS
An expansion joint with stainless steel collars with steel swivel flanges according to PN10/PN16 (see table) For applications in mainly heating systems, where a thermal expansion of the piping has to be absorbed. This type of expansion joint is basically meant for axial movements and where a short overall length is required.
TECHNICAL DESCRIPTION
Bellow (1) : AISI 316TiCollars (2) : AISI 321Flanges (3) : Carbon Steel
FLANGES
Swivel flanges, PN 16(DN 200 PN 10), carbon steel.
3
1
NL
2
DATA TABLE
DN Type
NLNeutral Length
AxialCompression
AxialExtension
Flangeconnection
Max.Pressure
Max.Pressure
mm (in.) mm mm mm mm bar/20°C bar/100°C
15(1/2) ANL 151620 130 -10 +10 PN 16 16 10
20(3/4) ANL 201622 130 -11 +11 PN 16 16 10
25(1) ANL 251630 130 -15 +15 PN 16 16 10
32(1.1/4) ANL 321630 130 -15 +15 PN 16 16 10
40(1.1/2) ANL 401638 130 -19 +19 PN 16 16 10
50(2) ANL 501634 130 -17 +17 PN 16 16 10
65(2.1/2) ANL 651630 130 -15 +15 PN 16 16 10
80(3) ANL 801636 130 -18 +18 PN 16 16 10
100(4) ANL 1001636 130 -18 +18 PN 16 16 10
125(5) ANL 1251636 130 -18 +18 PN 16 16 10
150(6) ANL 1501636 130 -18 +18 PN 16 16 10
200(8) ANL 2001630 130 -15 +15 PN 10 16 10
*For combined movements, consult AmniTec BV.
All information in this document is without any obligation, specifications subject to change without any notice.
www.amnitec.nl
STAINLESS STEEL EXPANSION JOINT, TYPE ALG
APPLICATIONS
An expansion joint with steel grooved ends for use within grooved end pipe systems, e.g. Grinnell, Victaulic, etc. Using these couplings and fittings, combines a number of advantages. The ease and swiftness of installation reduces the actual time needed “on site”. For applications in mainly heating systems, where a thermal expansion of the piping has to be absorbed. This type of expansion joint is basically meant for axial movements. The shown type is recommended for mounting with Grinnell Rigid couplings.
TECHNICAL DESCRIPTION
Bellow (1) : AISI 316TiGrooved ends (2) : Carbon steelInner sleeve(3) : AISI 304
DATA TABLE
DN Type
NLNeutral Length
AxialCompression
AxialExtension D E
Max.Pressure
Max.Pressure
mm (in.) mm mm mm mm mm bar/20°C bar/100°C
25(1) ALG 25-16-40 200 -20 +20 33,7x5,0 39 16 10
32(1.1/4) ALG 32-16-40 205 -20 +20 42,4x4,5 46 16 10
40(1.1/2) ALG 40-16-50 234 -25 +25 48,3x5 58 16 10
50(2) ALG 50-16-60 276 -30 +30 60,3x5 69 16 10
65(2.1/2) ALG 65-16-60 261 -30 +30 76,1x5 87 16 10
*For combined movements, consult AmniTec BV.
NL
1
E D
2 3
All information in this document is without any obligation, specifications subject to change without any notice.
www.amnitec.nl
STAINLESS STEEL EXPANSION JOINT, TYPE ANS
APPLICATIONS
An expansion joint with steel grooved ends for use within grooved end pipe systems, e.g. Grinnell, Victaulic, etc. Using these couplings and fittings, combines a number of advantages. The ease and swiftness of installation reduces the actual time needed “on site”. For applications in mainly heating systems, where a thermal expansion of the piping has to be absorbed. This type of expansion joint is basically meant for axial movements. The shown type is recommended for mounting with Grinnell Rigid couplings.
TECHNICAL DESCRIPTION
Bellow (1) : AISI 316TiGrooved ends (2) : Carbon steel
DATA TABLE
DN Type
NLNeutral Length
AxialCompression
AxialExtension D E
Max.Pressure
Max.Pressure
mm (in.) mm mm mm mm mm bar/20°C bar/100°C
80(3) ANS 80-16-40 205 -20 +20 88,9x6,3 104 16 10
100(4) ANS 100-16-40 200 -20 +20 114,3 x6,3 127 16 10
125(5) ANS 125-16-50 210 -25 +25 139,7x6,3 155 16 10
150(6) ANS 150-16-50 245 -25 +25 168,3x8 184 16 10
200(8) ANS 200-16-50 275 -25 +25 219,1x8 235 16 10
*For combined movements, consult AmniTec BV.
NL
1
E D
2
All information in this document is without any obligation, specifications subject to change without any notice.
www.amnitec.nl
STAINLESS STEEL EXPANSION JOINT, TYPE RXAG
APPLICATIONS
An expansion joint with steel grooved ends for use within grooved end pipe systems, e.g. Grinnell, Victaulic, etc. Using these couplings and fittings, combines a number of advantages. The ease and swiftness of installation reduces the actual time needed “on site”. For applications in mainly heating systems, where a thermal expansion of the piping has to be absorbed. This type of expansion joint is basically meant for axial movements, and has an outer protection sleeve. The shown type is recommended for mounting with Grinnell Rigid couplings.
TECHNICAL DESCRIPTION
Bellow (1) Grooved ends (2) End/Guide Ring (3) Outer protection sleeve (4)
DATA TABLE
DN Type
NLNeutral Length
AxialCompression
AxialExtension D E
Max.Pressure
Max.Pressure
mm (in.) mm mm mm mm mm bar/20°C bar/200°C
25(1) RXAG025 525 -70 +10 33,7x5,0 88,9 16 10
32(1.1/4) RXAG032 525 -70 +10 42,4x4,5 101,6 16 10
40(1.1/2) RXAG040 525 -70 +10 48,3x5 114,3 16 10
50(2) RXAG050 525 -70 +10 60,3x5 115 16 10
65(2.1/2) RXAG065 525 -70 +10 76,1x5 127 16 10
80(3) RXAG080 525 -70 +10 88,9x6,3 166 16 10
100(4) RXAG100 525 -70 +10 114,3 x6,3 178 16 10
125(5) RXAG125 525 -70 +10 139,7x6,3 219 16 10
150(6) RXAG150 525 -70 +10 168,3x8 273 16 10
200(8) RXAG200 525 -70 +10 219,1x8 324 16 10
250(10) RXAG250 525 -70 +10 273x8 400 16 10
300(12) RXAG300 525 -70 +10 323,9x8,0 457 16 10
*For combined movements, consult AmniTec BV.
4
3
2
1
ED
NL
: AISI 316Ti: Carbon Steel: Carbon Steel: AISI 304
All information in this document is without any obligation, specifications subject to change without any notice.