Embed Size (px)
Citation preview
SPIRA® Power Sections Specifications Handbook
SPIRA® Power Sections
Why SPIRA® ?
SPIRA® SPIRA® TNT
2
ARTEMIS Kautschuk- und Kunststoff - Technik GmbH | Rothwiese 4 | 30559 Hannover | Germany Ph. +49 (0)511/ 9 59 28-0 | Fax +49 (0)511/ 9 59 28-55 | [email protected] | www. artemis-kautschuk.de
Higher ROP by increased motor differential pressureHigher operating temperatureHigh performance, high temperature NBR & HNBR rubber compoundsIncreased longevity / less tripping / to depth drillingLends itself to low speed / high torque motor designsHigher torque at same length of conventional power sectionsShorter power sections at same torque of conventional power sectionsLess swelling & stator profile distortion by aggressive drilling fluidsUniform swelling around stator contourUniform heat expansion around stator contourMinimal stator profile distortion by heat expansionExcellent thermal conductivity through thin uniform rubber layer and contoured steel tubeMinimal internal heat-build-up no hysteresisHigh precision, consistent quality stators and rotors „Made in Germany“
3
Benefits of pre-contoured uniform rubber thickness SPIRA® stators
SPIRA® Power Sections
SPIRA® Power Sections
Table of Contents
Type Motor Output Motor Input Physical Motor DataBit Speed Torque Power Out Flow Range Motor Pressure No. of Stages No. of Lobes Displacement
rpm ft-lbs ( Nm) HP (kw) gqm (lpm) psi (bar) rev/gal (rev/l)
2.875“ 5/6 3.5 SPIRA 181-362 510 (694) 48 (36) 60-120 (227-454) 761 (53) 3.5 5/6 3.333 (0.888)
4.75“ 5/6 3.4 SPIRA 75-152 4,521 (6,149) 78 (57) 150-300 (568-1,136) 740 (51) 3.4 5/6 0.506 (0.134)
4.75“ 7/8 3.8 SPIRA TNT 78-156 4,410 (5,998) 110 (83) 150-300 (568-1,136) 827 (57) 3.8 7/8 0.521 (0.138)
5.00“ 5/6 8.3 SPIRA 105-280 6,900 (9,355) 297 (221) 100-275 (378-1041) 2140 (148) 8.3 5/6 1.015 (0.268)
6.75“ 5/6 3.9 SPIRA 61-182 8,622 (11,692) 240 (178) 200-600 (757-2,271) 856 (59) 3.9 5/6 0.304 (0.080)
6.75“ 5/6 5.3 SPIRA 61-182 11,618 (15,754) 327 (240) 200-600 (757-2,271) 1146 (79) 5.3 5/6 0.304 (0.080)
6.75“ 7/8 5.0 SPIRA TNT 58-173 11,576 (15,698) 310 (227) 200-600 (757-2,271) 1088 (75) 5.0 7/8 0.288 (0.076)
6.75“ 7/8 5.9 SPIRA TNT 58-173 13,660 (18,523) 365 (268) 200-600 (757-2,271) 1276 (88) 5.9 7/8 0.288 (0.076)
8.00“ 5/6 3.3 SPIRA 75-170 11,670 (15,871) 324 (243) 400-900 (1,514-3,407) 725 (50) 3.3 5/6 0.190 (0.050)
8.00“ 7/8 3.3 SPIRA TNT 65-145 21,000 (28,472) 460 (343) 400-900 (1514-3407) 1018 (70) 4.0 7/8 0.158 (0.042)
rev. 02/2019
4
ARTEMIS Kautschuk- und Kunststoff - Technik GmbH | Rothwiese 4 | 30559 Hannover | Germany Ph. +49 (0)511/ 9 59 28-0 | Fax +49 (0)511/ 9 59 28-55 | [email protected] | www. artemis-kautschuk.de
Power Section Fit ChangeSPIRA® Power Sections
0,00
0,05
0,10
0,15
0,20
0,25
0,30
0,35
0,40
0,00
0,05
0,10
0,15
0,20
0,25
0,30
0,35
0,40
0,45
0,50
0 50 100 150 200 250 300
Fit
Chan
ge in
Rad
ius
(inc
h)
Fit
Chan
ge in
Rad
ius
(mm
)
Temperature Change (°F)
28 56 83Temperature Change (°C)
111 13910 38 66 93 121
s = rubber thickness
5
SPIRA® Power Sections
Artemis 2.875“ 5/6 3.5 SPIRA®
No. of Stages 3.5No. of Lobes Rotor/Stator 5/6Overall Length 98.4 (2,500) inch (mm)Rubber Cutback 6.89 (175) inch (mm)Max. OD 2.875 (73) inch (mm)Connections to customer´s specificationRubber Types NBR, HNBR
Bit Speed 181-362 rpmFlow Range 60-120 (227-454) gqm (lpm)Displacement 3.333 (0.888) rev/gal (rev/l)Motor Pressure 761 (53) psi (bar)Torque 510 (694) ft-lbs (Nm)Power Out 48 (36) HP (Kw)
6 Performance curves are for reference only (@ 175 °F). Actual power section performance may vary depending on operating conditions (e.g. chosen rotor/stator interference fit, possible rubber swelling by drilling fluid, actual downhole temperature, actual stator temperature, physical properties of the drilling fluid). Data subject to change without notice.
ARTEMIS Kautschuk- und Kunststoff - Technik GmbH | Rothwiese 4 | 30559 Hannover | Germany Ph. +49 (0)511/ 9 59 28-0 | Fax +49 (0)511/ 9 59 28-55 | [email protected] | www. artemis-kautschuk.de
0
100
200
300
400
500
600
700
800
900
0
50
100
150
200
250
300
350
400
450
0 100 200 300 400 500 600 700 800 900 1000
Torq
ue (f
t-lbs
)
Bit
Spee
d (r
pm)
Motor Differential Pressure (psi)
ARTEMIS 2.75" 5/6 3.5 SPIRA© rev. 10/2011 (based on dynometer test)
120 gpm
90 gpm
60 gpm
Rated
7
SPIRA® Power Sections
Artemis 4.75“ 5/6 3.4 SPIRA®
No. of Stages 3.4No. of Lobes Rotor/Stator 5/6Overall Length 196 (4,978) inch (mm)Rubber Cutback 9.0 (229) inch (mm)Max. OD 4.8 (122) inch (mm)Connections to customer´s specificationRubber Types NBR, HNBROptions also with 5“ terminals available
Bit Speed 75-152 rpmFlow Range 150-300 (568-1,136) gqm (lpm)Displacement 0.506 (0.134) rev/gal (rev/l)Motor Pressure 740 (51) psi (bar)Torque 4,521 (6,149) ft-lbs (Nm)Power Out 78 (57) HP (Kw)
8 Performance curves are for reference only (@ 175 °F). Actual power section performance may vary depending on operating conditions (e.g. chosen rotor/stator interference fit, possible rubber swelling by drilling fluid, actual downhole temperature, actual stator temperature, physical properties of the drilling fluid). Data subject to change without notice.
ARTEMIS Kautschuk- und Kunststoff - Technik GmbH | Rothwiese 4 | 30559 Hannover | Germany Ph. +49 (0)511/ 9 59 28-0 | Fax +49 (0)511/ 9 59 28-55 | [email protected] | www. artemis-kautschuk.de
0
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
5500
6000
0
20
40
60
80
100
120
140
160
180
0 100 200 300 400 500 600 700 800 900
Torq
ue (f
t-lbs
)
Bit
Spee
d (r
pm)
Motor Differential Pressure (psi)
300 gpm
225 gpm
150 gpm
ARTEMIS 4.75" 5/6 3.4 SPIRA© rev. 10/2011 Rated
9
SPIRA® Power Sections
Artemis 4.75“ 7/8 3.8 SPIRA® TNTNo. of Stages 3.8No. of Lobes Rotor/Stator 7/8Overall Length 200 (5,080) inch (mm)Rubber Cutback 10.0 (254) inch (mm)Max. OD 4.8 (122) inch (mm)Connections to customer´s specificationRubber Types NBR, HNBROptions also with 5“ terminals available
Bit Speed 78-156 rpmFlow Range 150-300 (568-1,136) gqm (lpm)Displacement 0.521 (0.138) rev/gal (rev/l)Motor Pressure 827 (57) psi (bar)Torque 4,410 (5,998) ft-lbs (Nm)Power Out 110 (83) HP (Kw)
10 Performance curves are for reference only (@ 175 °F). Actual power section performance may vary depending on operating conditions (e.g. chosen rotor/stator interference fit, possible rubber swelling by drilling fluid, actual downhole temperature, actual stator temperature, physical properties of the drilling fluid). Data subject to change without notice.
ARTEMIS Kautschuk- und Kunststoff - Technik GmbH | Rothwiese 4 | 30559 Hannover | Germany Ph. +49 (0)511/ 9 59 28-0 | Fax +49 (0)511/ 9 59 28-55 | [email protected] | www. artemis-kautschuk.de
0
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
5500
6000
0
20
40
60
80
100
120
140
160
180
0 100 200 300 400 500 600 700 800 900
Torq
ue (f
t-lbs
)
Bit
Spee
d (r
pm)
Motor Differential Pressure (psi)
ARTEMIS 4.75" 7/8 3.9 SPIRA© TNT rev. 10/2011
300 gpm
225 gpm
150 gpm
Rated8
11
SPIRA® Power Sections
Artemis 5.00“ 5/6 8.3 SPIRA®
No. of Stages 8.3No. of Lobes Rotor/Stator 5/6Overall Length 245 (6,223) inch (mm)Rubber Cutback 8 (203,2) inch (mm)Max. OD 5.0 (127) inch (mm)Connections to customer´s specificationRubber Types NBR, HNBR
Bit Speed 105-280 rpmFlow Range 100-275 (378-1041) gqm (lpm)Displacement 1.015 (0.268) rev/gal (rev/l)Motor Pressure 2140 (148) psi (bar)Torque 6,900 (9355) ft-lbs (Nm)Power Out 297 (221) HP (Kw)
12 Performance curves are for reference only (@ 175 °F). Actual power section performance may vary depending on operating conditions (e.g. chosen rotor/stator interference fit, possible rubber swelling by drilling fluid, actual downhole temperature, actual stator temperature, physical properties of the drilling fluid). Data subject to change without notice.
ARTEMIS Kautschuk- und Kunststoff - Technik GmbH | Rothwiese 4 | 30559 Hannover | Germany Ph. +49 (0)511/ 9 59 28-0 | Fax +49 (0)511/ 9 59 28-55 | [email protected] | www. artemis-kautschuk.de
275 gpm
190 gpm
100 gpm
0
1000
2000
3000
4000
5000
6000
7000
8000
9000
0
50
100
150
200
250
300
0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800
Torq
ue (f
t-lbs
)
Bit
Spee
d (r
pm)
Motor Differential Pressure (psi)
ARTEMIS 5.00" 5/6 8.3 SPIRA© rev. 02.2019 Rated
13
SPIRA® Power Sections
Artemis 6.75“ 5/6 3.9 SPIRA®
No. of Stages 3.9No. of Lobes Rotor/Stator 5/6Overall Length 177.5 (4,508) inch (mm)Rubber Cutback 10.0 (254) inch (mm)Max. OD 6.93 (176) inch (mm)Connections to customer´s specificationRubber Types NBR, HNBROptions also with 7“ terminals available
Bit Speed 61-182 rpmFlow Range 200-600 (757-2,271) gqm (lpm)Displacement 0.304 (0.080) rev/gal (rev/l)Motor Pressure 856 (59) psi (bar)Torque 8,622 (11,692) ft-lbs (Nm)Power Out 240 (178) HP (Kw)
14 Performance curves are for reference only (@ 175 °F). Actual power section performance may vary depending on operating conditions (e.g. chosen rotor/stator interference fit, possible rubber swelling by drilling fluid, actual downhole temperature, actual stator temperature, physical properties of the drilling fluid). Data subject to change without notice.
ARTEMIS Kautschuk- und Kunststoff - Technik GmbH | Rothwiese 4 | 30559 Hannover | Germany Ph. +49 (0)511/ 9 59 28-0 | Fax +49 (0)511/ 9 59 28-55 | [email protected] | www. artemis-kautschuk.de
0
1000
2000
3000
4000
5000
6000
7000
8000
9000
10000
0
20
40
60
80
100
120
140
160
180
200
0 100 200 300 400 500 600 700 800 900 1000
Torq
ue (f
t-lbs
)
Bit
Spee
d (r
pm)
Motor Differential Pressure (psi)
ARTEMIS 6.75" 5/6 5.0 SPIRA© rev. 10/2011 (based on dynometer test)
600 gpm
400 gpm
200 gpm
Rated
15
SPIRA® Power Sections
Artemis 6.75“ 5/6 5.3 SPIRA®
No. of Stages 5.3No. of Lobes Rotor/Stator 5/6Overall Length 235.8 (5,990) inch (mm)Rubber Cutback 10.0 (254) inch (mm)Max. OD 6.93 (176) inch (mm)Connections to customer´s specificationRubber Types NBR, HNBROptions also with 7“ terminals available
Bit Speed 61-182 rpmFlow Range 200-600 (757-2,271) gqm (lpm)Displacement 0.304 (0.080) rev/gal (rev/l)Motor Pressure 1146 (79) psi (bar)Torque 11,618 (15,754) ft-lbs (Nm)Power Out 327 (240) HP (Kw)
16 Performance curves are for reference only (@ 175 °F). Actual power section performance may vary depending on operating conditions (e.g. chosen rotor/stator interference fit, possible rubber swelling by drilling fluid, actual downhole temperature, actual stator temperature, physical properties of the drilling fluid). Data subject to change without notice.
ARTEMIS Kautschuk- und Kunststoff - Technik GmbH | Rothwiese 4 | 30559 Hannover | Germany Ph. +49 (0)511/ 9 59 28-0 | Fax +49 (0)511/ 9 59 28-55 | [email protected] | www. artemis-kautschuk.de
0
2000
4000
6000
8000
10000
12000
14000
16000
18000
20000
0
20
40
60
80
100
120
140
160
180
200
0 200 400 600 800 1000 1200 1400 1600
Torq
ue (f
t-lbs
)
Bit
Spee
d (r
pm)
Motor Differential Pressure (psi)
ARTEMIS 6.75" 5/6 5.3 SPIRA© rev. 10/2012 (based on dynometer test)
600 gpm
400 gpm
200 gpm
Rated
17
SPIRA® Power Sections
Artemis 6.75“ 7/8 5.0 SPIRA® TNTNo. of Stages 5.0No. of Lobes Rotor/Stator 7/8Overall Length 200 (5,080) inch (mm)Rubber Cutback 10.0 (259) inch (mm)Max. OD 6.89 (173) inch (mm)Connections to customer´s specificationRubber Types NBR, HNBROptions also with 7“ terminals available
Bit Speed 58-173 rpmFlow Range 200-600 (757-2,271) gqm (lpm)Displacement 0.288 (0.076) rev/gal (rev/l)Motor Pressure 1088 (75) psi (bar)Torque 11,576 (15,698) ft-lbs (Nm)Power Out 310 (227) HP (Kw)
18 Performance curves are for reference only (@ 175 °F). Actual power section performance may vary depending on operating conditions (e.g. chosen rotor/stator interference fit, possible rubber swelling by drilling fluid, actual downhole temperature, actual stator temperature, physical properties of the drilling fluid). Data subject to change without notice.
ARTEMIS Kautschuk- und Kunststoff - Technik GmbH | Rothwiese 4 | 30559 Hannover | Germany Ph. +49 (0)511/ 9 59 28-0 | Fax +49 (0)511/ 9 59 28-55 | [email protected] | www. artemis-kautschuk.de
0
2000
4000
6000
8000
10000
12000
14000
16000
18000
0
20
40
60
80
100
120
140
160
180
0 200 400 600 800 1000 1200 1400
Torq
ue (f
t-lbs
)
Bit
Spee
d (r
pm)
Motor Differential Pressure (psi)
ARTEMIS 6.75" 7/8 5.0 SPIRA© TNT rev. 10/2011 (based on dynometer test)
600 gpm
400 gpm
200 gpm
Rated
19
SPIRA® Power Sections
Artemis 6.75“ 7/8 5.9 SPIRA® TNTNo. of Stages 5.9No. of Lobes Rotor/Stator 7/8Overall Length 235.8 (5,990) inch (mm)Rubber Cutback 10.0 (259) inch (mm)Max. OD 6.89 (175) inch (mm)Connections to customer´s specificationRubber Types NBR, HNBROptions also with 7“ terminals available
Bit Speed 58-173 rpmFlow Range 200-600 (757-2,271) gqm (lpm)Displacement 0.288 (0.076) rev/gal (rev/l)Motor Pressure 1276 (88) psi (bar)Torque 13,660 (18,523) ft-lbs (Nm)Power Out 365 (268) HP (Kw)
20 Performance curves are for reference only (@ 175 °F). Actual power section performance may vary depending on operating conditions (e.g. chosen rotor/stator interference fit, possible rubber swelling by drilling fluid, actual downhole temperature, actual stator temperature, physical properties of the drilling fluid). Data subject to change without notice.
ARTEMIS Kautschuk- und Kunststoff - Technik GmbH | Rothwiese 4 | 30559 Hannover | Germany Ph. +49 (0)511/ 9 59 28-0 | Fax +49 (0)511/ 9 59 28-55 | [email protected] | www. artemis-kautschuk.de
0
2000
4000
6000
8000
10000
12000
14000
16000
18000
20000
0
20
40
60
80
100
120
140
160
180
200
0 200 400 600 800 1.000 1.200 1.400 1.600 1.800
Torq
ue (f
t-lbs
)
Bit
Spee
d (r
pm)
Motor Differential Pressure (psi)
ARTEMIS 6.75" 7/8 5.9 SPIRA© TNT rev. 10/2012 (based on dynometer test)
600 gpm
400 gpm
200 gpm
Rated
21
SPIRA® Power Sections
Artemis 8.00“ 5/6 3.3 SPIRA®
No. of Stages 3.3No. of Lobes Rotor/Stator 5/6Overall Length 177.5 (4,508) inch (mm)Rubber Cutback 9 (229) inch (mm)Max. OD 8.25 (210) inch (mm)Connections to customer´s specificationRubber Types NBR, HNBROptions Terminal for 9 5/8“ Lower Section avail.
Bit Speed 75-170 rpmFlow Range 400-900 (1,514-3,407) gqm (lpm)Displacement 0.190 (0.050) rev/gal (rev/l)Motor Pressure 725 (50) psi (bar)Torque 11,670 (15,871) ft-lbs (Nm)Power Out 324 (243) HP (Kw)
22 Performance curves are for reference only (@ 175 °F). Actual power section performance may vary depending on operating conditions (e.g. chosen rotor/stator interference fit, possible rubber swelling by drilling fluid, actual downhole temperature, actual stator temperature, physical properties of the drilling fluid). Data subject to change without notice.
ARTEMIS Kautschuk- und Kunststoff - Technik GmbH | Rothwiese 4 | 30559 Hannover | Germany Ph. +49 (0)511/ 9 59 28-0 | Fax +49 (0)511/ 9 59 28-55 | [email protected] | www. artemis-kautschuk.de
0
2000
4000
6000
8000
10000
12000
14000
16000
18000
20000
0
20
40
60
80
100
120
140
160
180
200
0 100 200 300 400 500 600 700 800 900 1000
Torq
ue (f
t-lbs
)
Bit
Spee
d (r
pm)
Motor Differential Pressure (psi)
ARTEMIS 8.00" 5/6 3.3 SPIRA© rev. 10/2011
900 gpm
650 gpm
400 gpm
Rated
23
SPIRA® Power Sections
Artemis 8.00“ 7/8 4.0 SPIRA® TNTNo. of Stages 4.0No. of Lobes Rotor/Stator 7/8Overall Length 223.5 (5676,9) inch (mm)Rubber Cutback 18 (457,2) inch (mm)Max. OD 8.125 (206,4) inch (mm)Connections to customer´s specificationRubber Types NBR, HNBR
Bit Speed 65-145 rpmFlow Range 400-900 (1,514-3,407) gqm (lpm)Displacement 0.158 (0.042) rev/gal (rev/l)Motor Pressure 1018 (70) psi (bar)Torque 21,000 (28.472) ft-lbs (Nm)Power Out 460 (343) HP (Kw)
24 Performance curves are for reference only (@ 175 °F). Actual power section performance may vary depending on operating conditions (e.g. chosen rotor/stator interference fit, possible rubber swelling by drilling fluid, actual downhole temperature, actual stator temperature, physical properties of the drilling fluid). Data subject to change without notice.
ARTEMIS Kautschuk- und Kunststoff - Technik GmbH | Rothwiese 4 | 30559 Hannover | Germany Ph. +49 (0)511/ 9 59 28-0 | Fax +49 (0)511/ 9 59 28-55 | [email protected] | www. artemis-kautschuk.de
900 gpm
650 gpm
400 gpm
0
2500
5000
7500
10000
12500
15000
17500
20000
22500
25000
27500
30000
0
25
50
75
100
125
150
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400
Torq
ue (f
t-lbs
)
Bit
Spee
d (r
pm)
Motor Differential Pressure (psi)
ARTEMIS 8.00" 7/8 4.0 SPIRA© TNT rev. 02.2019 Rated
25
ARTEMIS Kautschuk- und Kunststoff- Technik GmbHRothwiese 430559 HannoverGermany +49 511 959 280
+49 511 959 2855 [email protected] www.artemis-kautschuk.de
Disclaimer
We exclude any liability for the information and product presentations provided. Contents of technical character are based on the date of publication. Existing copyrights and rights to the use of names remain unaffected.
![Artigo kautschuk-boden-prospekt-prospekt[1]](https://img.dokumen.tips/doc/110x75/55ae02c81a28abf9198b46cf/artigo-kautschuk-boden-prospekt-prospekt1.jpg)
