Embed Size (px)
DESCRIPTION
Technical Data
Citation preview
SpEC
ENGINEERED SOLUTIONS
SpECtop CPD UVR
DESCRIPTION
SpECtop CPD UVR is a solvent free high build
polyurethane floor seal for concrete, grano and
asphalt. With excellent resistances to abrasion,
chemical attack and other physical aggression
including flexing/minor movement. With a high order
of UV resistance.
TYPICAL USES
SpECtop CPD UVR is ideally suited for use as a
final finish coat with a high order of UV resistance.
ADVANTAGES
. Excellent adhesion
. Durable and hard wearing
. UV stable and weather resistant
. Protection from carbonation
. Anti-graffiti properties
. Hygienic sterile finish
. Resistant to a wide range of chemicals
. Available in gloss, silk or matt finish
TECHNICAL DATA
Elongation at break (BS 2782) 70%
Hardness Shore ‘D’ 62
Tensile strength (BS 2782) 7N/mm²
Tear strength (BS 903) die ‘C’ 33N/mm²
Compressive strength (BS 6319) 90N/mm²
no failure (85% recovery)
Taber abrasion
dry CS10/1000 cycles/1kg 80mg
dry H18/1000 cycles/1kg 400mg
Curing Schedule @ 20°C
Pot life 15-20 mins
Initial film set time 4 hrs
Resistant to light traffic 16 hrs
Full cure/chemical resistance 4-5 days
CHEMICAL RESISTANCE
Excellent resistances to organic and inorganic acids,
alkalis, fuel and hydraulic oils, aromatic and aliphat-
ic hydrocarbon solvents and ester solvents. Limited
resistances to ketones and alcohols.
APPLICATION
Substrate preparation
Surfaces to be treated must be sound, free from
oil or other contaminants, loosely adhering coatings,
laitance and dust.
If the maximum overcoating time is missed please
contact SpEC’s Technical Department for advice.
Mixing
Pour and fully drain the contents of the clear hard-
ener component into the pigmented resin compo-
nent and mix thoroughly for a minimum of three
minutes or until a homogeneous mix is obtained pay-
ing special attention to scrape the sides and base of
container.
Application
The mixed product should then be applied to the pre-
pared substrate by brush, roller or spray. Care should
be taken to avoid over application.The application of
excessive volumes of product should be avoided as
this will result in solvent entrapment affecting both
surface finish and the subsequent performances of
the coating.
EQUIPMENT CLEANING
Clean all tools and equipment immediately before
and after use with SpECtop PU Cleaning Solvent.
APPLICATION TEMPERATURE RANGE
Minimum 10°C
Maximum 30°C
PACKAGING & YIELD
SpECtop CPD UVR is supplied in 10kg pack size
with a coverage rate of 0.35 - 0.70kg/m².
CCAARR PPAARRKK DDEECCKKIINNGG UUVV SSTTAABBLLEE TTOOPP CCOOAATT
A BARDAWIL INTERNATIONAL COMPANY
STORAGE & SHELF LIFE
When stored in a cool environment, in original
unopened containers, the material has a shelf life
of 12 months.
HEALTH & SAFETY
Contact with skin and eyes should be avoided. It is
essential that adequate ventilation is provided and
all personnel should avoid inhaling the vapours
produced. If working is necessary in a confined area
it is strongly recommended that sealed respiratory
equipment is utilised.
Eye Contact rinse with copious
amounts of clean water
and seek medical
attention.
Skin Contact rinse with copious
amounts of clean water
followed by thorough
cleaning with soap and
water.
DO NOT USE SOLVENTS
Ingestion seek immediate medical
attention.
DO NOT INDUCE VOMITING
FLAMMABILITY
SpECtop PU Cleaning Solvent is flammable. Do
not expose to naked flame or other ignition
sources.
FLASHPOINT
SpECtop PU Cleaning Solvent 34°C
SPECIALITY ENGINEERING CHEMICALSPO Box 61347, Dubai, United Arab Emirates. Telephone: +971 4 883 6662, Fax: +971 4 883 7696
E-mail: [email protected]
Whilst the information and/or specifications given are, to the best of our knowledge, true and accurate, no warranty is given or implied in any connection with anyrecommendations or suggestions made by us, our representatives, agents or distributors as the conditions of use and labour involved are beyond our control.
Issue 2 : 05/2004
