Upload
others
View
6
Download
0
Embed Size (px)
Citation preview
Louisiana State UniversityLSU Digital Commons
LSU Historical Dissertations and Theses Graduate School
1998
Spatial Variability of Coastal Organic SoilCharacteristics.L. Cecil DharmasriLouisiana State University and Agricultural & Mechanical College
Follow this and additional works at: https://digitalcommons.lsu.edu/gradschool_disstheses
This Dissertation is brought to you for free and open access by the Graduate School at LSU Digital Commons. It has been accepted for inclusion inLSU Historical Dissertations and Theses by an authorized administrator of LSU Digital Commons. For more information, please [email protected].
Recommended CitationDharmasri, L. Cecil, "Spatial Variability of Coastal Organic Soil Characteristics." (1998). LSU Historical Dissertations and Theses. 6824.https://digitalcommons.lsu.edu/gradschool_disstheses/6824
INFORMATION TO USERS
This manuscript has been reproduced from the microfilm master. U M I
films the text directly from the original or copy submitted. Thus, some
thesis and dissertation copies are in typewriter face, while others may be
from any type of computer printer.
The quality of this reproduction is dependent upon the quality of the
copy submitted. Broken or indistinct print, colored or poor quality
illustrations and photographs, print bleedthrough, substandard margins,
and improper alignment can adversely affect reproduction.
In the unlikely event that the author did not send U M I a complete
manuscript and there are missing pages, these will be noted. Also, if
unauthorized copyright material had to be removed, a note will indicate
the deletion.
Oversize materials (e.g., maps, drawings, charts) are reproduced by
sectioning the original, beginning at the upper left-hand comer and
continuing from left to right in equal sections with small overlaps. Each
original is also photographed in one exposure and is included in reduced
form at the back of the book.
Photographs included in the original manuscript have been reproduced
xerographically in this copy. Higher quality 6” x 9” black and white
photographic prints are available for any photographs or illustrations
appearing in this copy for an additional charge. Contact U M I directly to
order.
UMIA Bell & Howell Information Company
300 North Zeeb Road, Ann Arbor MI 48106-1346 USA 313/761-4700 800/521-0600
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
SPATIAL VARIABILITY O F COASTAL ORGANIC SOIL CHARACTERISTICS
A Dissertation
Submitted to the Graduate Faculty of the Louisiana State University and
Agricultural and Mechanical College in partial fulfillment of the
requirements for the degree of Doctor of Philosophy
in
The Department of Agronomy
byL. Cecil Dharmasri
B.S., University of Peradeniya, 1984 M.S., University of Saskatchewan, 1995
December 1998
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
UMI Number: 9922073
UMI Microform 9922073 Copyright 1999, by UMI Company. All rights reserved.
This microform edition is protected against unauthorized copying under Title 17, United States Code.
UMI300 North Zeeh Road Ann Arbor, MI 48103
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
ACKNOWLEDGEMNTS
I am very much grateful and express my sincere thanks to my major
advisor, Dr. W ayne H. Hud nail for his valuable guidance, advice, and constant
help during my study program. I thank Dr. Nina Lam, Dr. R. D. DeLaune, Dr.
Ray E. Ferrell Jr., Dr. Ramona Travis, Dr. Gary A. Breitenbeck and Dr. Jeff Hoy
for their advice while serving in my graduate committee. The NASA/EPSCoR
program supported the research, under cooperative agreement NCCW -0059
and the Louisiana Board of Regents/LEQSF under the contract NASA/LEQSF
(1994-97)-IM P-03. I am thankful to Dr. Ken Holladay and the members of the
project. I am very much thankful to Joaney Haigler for ICP-AES analysis and
W anda LeBlanc and Xiaogang Xie for mineralogical investigations. My thanks
are also due for my friend Asfaw Bekele who was with me when in need. I am
thankful to the student assistants and the EPSCoR summer intern, Ms. Betty A.
Odom who helped me in the laboratory. I thank my colleagues. Lamine Coly,
Rodney Young, Salena Agra va I, Lois West, Bill Patterson, and Clint Waddell
who shared the resources with me during this period. I express my gratitude
and commitment to the Department of Agriculture, Sri Lanka for releasing me to
pursue higher studies. I am grateful to Anura and Venika, Asoka and Upuli, and
Gumar (Gala) and Usha for their unreserved care and help for our family during
our stay in Baton Rouge. The constant encouragement and patient
understanding of my wife, Ayesha, through out my graduate studies for over six
years, is remembered most affectionately. I dedicate this dissertation to my
dearest sons, Poorna and Chamara, who were unaware of their sacrifice.
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
TABLE OF CONTENTS
ACKNOWLEDGMENTS..................................................................................... ii
LIST OF TABLES................................................................................................. vi
LIST OF FIGURES............................................................................................. vii
ABSTRACT......................................................................................................... xii
CHAPTER 1: INTRODUCTION........................................................................ 11.1 References...................................................................................... 9
CHAPTER 2: ESTIMATE SALINITY PARAMETERS ANDELEMENTAL RATIOS FOR THE ESTUARINEWATER SYSTEM OF BARATARIA BAY BASIN .................. 13
2.1 Summary and Introduction............................................................. 132.2 Literature Review......................................................................... 15
2.2.1 Barataria Bay Basin Water System .............................. 152.2.2 Seawater Salinity, the Major Elements, and Salinity
Parameters................................................................. 182.3 Materials and M ethods............................................................. 19
2.3.1 Sample Collection and Preparation.............................. 192.3.2 Chemical Analysis......................................................... 212.3.3 Measurement of T D S ..................................................... 21
2.4 Results and Discussion............................................................. 222.4.1 Elemental Composition.................................................. 222.4.2 Electrical Conductivity and Elemental Concentrations.. 242.4.3 Elemental Ratios............................................................. 262.4.4 Electrical Conductivity and Salin ity.............................. 32
2.5 Conclusions................................................................................. 362.6 References................................................................................. 36
CHAPTER 3:USE OF ION-EXCHANGE RESIN STRIPS FORELEMENTAL ANALYSIS OF ESTUARINE WATERAND COASTAL ORGANIC SOILS.......................................... 39
3.1 Summary and Introduction............................................................. 393.2 Literature Review ..................................................................... 43
3.2.1 Multi-Elemental Analysis in Soil Using Ion-Exchange Resins......................................................................... 43
3.2.2 Effect of Soluble Salts on Membrane Extractable Elements......................................................................... 45
3.2.3 Estimation of Membrane Exchangeable S ...................453.2.4 Methodology Adopted in Resin Extraction of S 46
3.3 Materials and M ethods..................................................................... 473.3.1 Salinity and Chloride Effect........................................ 49
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
3.3.2 Multi-Elemental Analysis of Estuarine W ater.............. 493.3.3 Resin-Extractable S Analysis for Coastal Organic
S o ils ................................................................................. 503.3.3.1 Equilibration and Elution Time Experiment... 503.3.3.2 Soil/Water Ratio Experiment.................. 513.3.3.3 Resin-Extractable and Water Soluble S
Analys is ............................................. 513.3.3.4 Pyritic and Non-pyritic S Analysis 52
3.3.4 Data Analysis................................................................. 533.4 Results and Discussion................................................................ 54
3.4.1 Salinity and Chloride E ffect........................................... 543.4.2 Multi-Elemental Analysis of Estuarine W ater............... 583.4.3 Resin Extractable S in Coastal Organic S o ils ............... 69
3.4.3.1 Equilibration and Elution T im e ........................ 693.4.3.2 Soil/Water R a tio ................................................ 693.4.3.3 Resin Extractable S .......................................... 73
3.5 Conclusions................................................................................. 803.6 References.................................................................................... 81
CHAPTER 4: INFLUENCE OF SALINITY AND LANDSCAPEPOSITION ON ACCUMULATION OF PYRITE AND NON-PYRITIC Fe AND S WITHIN COASTAL ORGANIC SOILS OF BARATARIA BAY BASIN, LOUISIANA............... 86
4.1 Summary and Introduction............................................................. 864.2 Literature Review..................................................................... 89
4.2.1 Marsh Loss around Barataria Bay Basin, Louisiana ... 894.2.2 Seawater Intrusion, Salinity and Marsh Types 904.2.3 Pyrite Formation and Accumulation.............................. 924.2.4 Sulfur Dynamics within the M arsh............................... 954.2.5 Pore Water Dynamics and Mineral Formation............. 994.2.6 Pyrite Crystal Formation................................................. 994.2.7 Spatial Variability of Pedogenic Processes.............. 1004.2.8 Soil Classification and Soil Taxonomy...................... 1024.2.9 Pyrite Determination........................................................ 104
4.3 Materials and Methods................................................................. 1064.3.1 Site Description and Sampling Procedure.................. 1064.3.2 Measurement of EC and T D S ...................................... 1084.3.3 Pyrite and Non-pyritic Fe and S Determination 1084.3.4 Measurement of Soil p H ............................................... 1104.3.5 Microanalysis of Marsh S o ils ........................................ 1104.3.6 Data Analysis................................................................. I l l
4.4 Results and Discussion............................................................. 1124.4.1 Soil Horizon Thickness and Bulk Density.................. 1124.4.2 Soil Salin ity..................................................................... 1184.4.3 Pyrite Accumulation and Pyrite Profiles...................... 1274.4.4 Non-pyritic F e ................................................................. 136
IV
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
4.4.5 Non-pyritic S ................................................................. 1444.4.6 Soil p H ............................................................................. 1514.4.7 Microanalysis of Soils for Pyrite .................................. 1544.4.8 Soil Classification.......................................................... 162
4.5 Summary and Future Research Needs.................................. 1664.6 References................................................................................. 173
CHAPTER 5: SPATIAL VARIABILITY OF COASTAL ORGANICSOIL CHARACTERISTICS WITHIN THE BARATARIABAY BASIN, LOUISIANA........................................................ 180
5.1 Summary and Introduction......................................................... 1805.2 Literature Review ..................................................................... 184
5.2.1 Barataria Bay Coastal M arsh...................................... 1845.2.2 Soil Morphology and Classification.............................. 1885.2.3 Spatial Variability of Marsh Soil Characteristics............1895.2.4 Spatial Interpolation Methods...................................... 190
5.3 Materials and M ethods............................................................. 1955.3.1 Site Description............................................................. 1955.3.2 Data Collection.................................................................. 1975.3.3 Data Analysis................................................................. 200
5.4 Results and Discussion............................................................. 2025.4.1 Thickness of Organic Subhorizons.............................. 202
5.4.1.1 Exploratory Data Analysis...................... 2025.4.1.2 Spatial Data Analysis.............................. 204
5.4.2 Depth to Mineral Layer (DML) and Soil Subgroup Delineation.......................................................................2105.4.2.1 Exploratory Data Analysis.......................... 2105.4.2.2 Spatial Data Analysis............................... 2135.4.2.3 Spatial Distribution of Soil Subgroups .... 216
5.4.2 pH for Ditferent Subhorizons.................................. 2165.4.2.1 Exploratory Data Analysis.......................... 2165.4.2.2 Spatial Data Analysis.................................. 219
5.4.3 Organic/Mineral Ratio (OMR) for Different Subhorizons................................................................. 2245.4.3.1 Exploratory Data Analysis.......................... 2245.4.3.2 Spatial Data Analysis............................... 227
5.5 Conclusions................................................................................. 2305.7 References................................................................................. 235
CHAPTER 6:C0NCLUSI0NS......................................................... 239
VITA.................................................................................................... 248
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
LIST OF TABLES
2.1 Sample locations and EC measurements.................................................. 20
2.2 Electrical conductivity, pH and elemental concentrationranges of water samples................................................................................. 23
2.3 Element/Chloride ratios of water samples..................................................... 30
3.1 Electrical conductivity, pH and elemental concentration rangesof water samples used in the experiment................................................... 59
3.2 Regression model for different elements to predict elementsin the water using resin extracted elements.......................................... 67
3.3 Regression models to predict different sulfur fractionsfrom RES for organic and mineral soil layers.......................................... 79
4.1 Sulfur species (ppm) variation in 0-50 cm depth for differentmarshes in the Barataria Bay, Louisiana.................................................. 98
4 .2 Average thickness of different subhorizons of soil profilesat different landscape positions............................................................... 113
5.1 The variables used for spatial analysis for each marsh type 201
5.2 Modal parameters and regression coefficients, for the semivariograms for the thickness of organic subhorizonsat both sites....................................................................................................... 204
5.3 Modal parameters and regression coefficients of thesemivariograms for the DML at both sites.............................................. 213
5.4 Semivariogram model parameters for pH of soil subhorizonsat both s ite s ................................................................................................... 2 2 2
5.5 Modal parameters and regression coefficients for thesemivariograms for OMR for organic soil horizons at both sites ... 227
VI
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
LIST OF FIGURES
1.1 Schematic representation of the linkage between differentchapters of the dissertation........................................................................ 6
2.1 A map showing different marsh types within the BaratariaBay Basin............................................................................................................ 16
2.2 Electrical conductivity and the major cations of water samples ... 25
2.3 Upper and lower confidence intervals (95% ) for Clconcentration at different EC levels....................................................... 27
2.4 Upper and lower confidence intervals for SO 4
concentration at different EC levels....................................................... 28
2.5 Relationship between C I/S 04 ratio and EC of water samples 31
2.6 Chloride/sulfate ratio data for different marsh types............................. 33
2.7 The relationship between EC and T D S ................................................. 34
2.8 The relationship between EC and T D S ............................................... 35
3.1 Schematic presentation of the general procedurefor resin extraction.......................................................................................... 48
3.2 Effect of salinity and sulfate level on resin extractable sulfate 55
3.3 Effect of chloride concentration on resin extractable sulfateat 600 mg S L" ........................................................................................... 56
3.4 Response surface for resin extractable S as affected bysulfate and chloride levels......................................................................... 57
3.5 Potassium and sulfur concentration as influenced by electricalconductivity in water samples..................................................................... 60
3.6 Resin extracted K at different K levels in water.......................................... 62
3.7 Relationship between electrical conductivity and resin extracted-K... 63
3.8 Resin extracted milliequivalent percentages of major cations............... 64
3.9 Sulfate milliequivalents exchanged onto the resin atdifferent EC levels of water samples..................................................... 65
VII
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
3.10 Effect of equilibration time on resin extractable S from organic soils.. 70
3.11 Effect of elution time on resin extractable S ............................................... 71
3.12 Effect of soil/water ratio on resin extractable S ....................................... 72
3.13 Boxplots showing data for different S fractions for organicand mineral horizons............................................................................... 74
3.14 Relationship between RES and W SS for organic horizons 76
3.15 Relationship between RES and NFS for organic horizons 77
3.16 Relationship between RES and NFS for mineral horizons 78
4.1 A map showing different marsh types within theBarataria Bay Basin...................................................................................... 107
4 .2 Variation in soil bulk density for saline and brackish m arshes 119
4 .3 Salinity profiles for streamside (SSS) and inland (SIL)for the saline marsh...................................................................................... 1 2 1
4 .4 Salinity profiles for streamside (BSS) and inland (BIL)for the brackish marsh................................................................................ 123
4 .5 Salinity profiles for streamside (ISS) and inland (ML)for the intermediate m arsh ......................................................................... 124
4.6 Salinity profiles for streamside (FSS) and inland (FIL)for the fresh marsh......................................................................................... 125
4.7 Weighted average of salinity for the profile up to 150 cm................. 126
4.8 Fyrite profiles for streamside (SSS) and inland (SIL)for the saline m arsh ............................................................................. 130
4.9 Fyrite profiles for streamside (BSS) and inland (BIL)for the brackish m arsh .................................................................................. 132
4.10 Fyrite profiles for streamside (ISS) and inland (ML)for the intermediate m arsh ......................................................................... 133
4.11 Fyrite profiles for streamside (FSS) and inland (FIL)for the fresh m arsh ...................................................................................... 134
VIII
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
4.12 Weighted average of pyrite content for the soil profileup to a depth of 150 c m ................................................................. 135
4.13 Non-pyritic Fe profiles for streamside (SSS) andinland (SIL) for the saline m arsh ........................................................ 137
4.14 Non-pyritic Fe profiles for streamside (BSS) andinland (BIL) for the brackish m arsh ........................................................ 138
4.15 Non-pyritic Fe profiles for streamside (ISS) andinland (ML) for the intermediate m arsh ................................................ 139
4.16 Non-pyritic Fe profiles for streamside (FSS) andinland (FIL) for the fresh m arsh ............................................................ 140
4.17 Weighted average non-pyritic Fe for the soil profileto a depth of 150 c m .................................................................................. 142
4.18 Non-pyritic S profiles for streamside (SSS) and inland (SIL)for the saline m arsh .................................................................................. 145
4 .19 Non-pyritic S profiles for streamside (BSS) and inland (BIL)for the brackish m arsh ............................................................................ 146
4.20 Non-pyritic S profiles for streamside (ISS) and inland (ML)for the intermediate m arsh ..................................................................... 147
4.21 Non-pyritic S profiles for streamside (FSS) and inland (FIL)for the fresh m arsh .................................................................................. 149
4.22 Weighted average of non-pyritic S for the soil profileto a depth of 150 c m .................................................................................. 150
4.23 The pH profiles for streamside of all marsh types............................. 152
4.24 The pH profiles for inland of all marsh types..................................... 153
4.25 Scanning electron micrograph showing microstructureof coastal marsh sediments...................................................................... 156
4.26 Scanning electron micrograph showing pyrite framboids within organic material of saline marsh sediments from the O a l horizon... 157
4.27 A close up of pyrite framboids within saline marshsediments from the O a l horizon........................................................... 158
IX
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
4.28 A single pyrite framboid within saline marshsediments from the Oa1 horizon............................................................. 159
4.29 The XRD patterns of saline marsh sediments (<2 pm)from the O a l horizon.............................................................................. 160
4.30 The XRD patterns of saline marsh sediments (<20 pm)from the O a l horizon..................................................................................... 161
4.31 The XRD patterns of brackish marsh sediments (<2 pm)from the O a l horizon.................................................................................. 163
4.32 The XRD patterns of brackish marsh sediments (<20 pm)from the O a l horizon.................................................................................. 164
4.33 Differential XRD patterns between 2 and 20 pm fractionsfrom the O a l horizons at saline and brackish m arshes.................... 165
5.1 An idealized coastal organic soil profile with subhorizons................. 188
5.2 Major features of an ideal semivariogram............................................... 193
5.3 Site locations for the saline marsh (8 ) and the brackish marsh (B)shown on a satellite image for southern Louisiana............................. 196
5.4 Maps showing dominant open water areas (W) and waterwayswithin the sites at saline (A) and brackish (B) marsh ty p e s .............. 198
5.5 Sampling plan for both sites, showing the sampling pointson the grid......................................................................................................... 199
5.6 Boxplots showing the data for organic subhorizon thicknessat both sites.................................................................................................. 203
5.7 Semivariograms for S0A 1TH , S 0A 2TH , and SOA3TH d a ta 206
5.8 Semivariograms for B0A1TH, B0A 2TH , and BOA3TH d a ta 207
5.9 Spatial variability of O a l , Qa2, and Ga3 horizon thicknessfor the saline marsh..................................................................................... 208
5.10 Spatial variability of O a l , Oa2, and Oa3 horizon thicknessfor the brackish marsh................................................................................. 209
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
5.11 Boxplots showing the data for depth to mineral layer (DML)for both sites.................................................................................................. 2 1 2
5.12 Semivariograms for the SDML and BDML d a ta ..................................... 214
5.13 Spatial variability of depth to mineral layer for the saline marsh (A)and brackish marsh ( B ) ............................................................................... 215
5.14 Spatial variability of the soils for the saline and brackishmarsh types...................................................................................................... 217
5.15 Boxplots showing the data for pH of soil subhorizons andweighted average pH for the organic layer for both sites................ 218
5.16 Semivariograms for S0A1 PH, S0A 2PH , S 0A 3P H , andSCGPH d a ta .................................................................................................. 220
5.17 Semivariograms for B0A1PH, BOA2PH, BOA3PH, andBCGPH data.................................................................................................... 221
5.18 Spatial variability of soil pH for O a l (A), Ga2 (B), Ga3 (C),and Cg (D) horizons for the saline marsh.............................................. 223
5.19 Spatial variability of soil pH for G a l (A), Ga2 (B), Ga3 (C),and Cg (D) horizons for the brackish marsh.......................................... 225
5.20 Boxplots showing the data for organic/mineral ratio (GMR) for different organic subhorizons and weighted average GMRfor the organic layer for both sites............................................................. 226
5.21 Semivariograms for SGA1GMR, SGA2GMR, and SGA3GMR data 228
5.22 Semivariograms for BGA1GMR, BGA2GMR, and BGA3GMR data 229
5.23 Grganic/mineral ratio for the G a l (A), Ga2 (B), and Ga3 (0 )horizons at the saline marsh....................................................................... 231
5.24 Grganic/mineral ratio for the G a l (A), Ga2 (B), and Ga3 (C) horizons at the brackish marsh................................................................. 232
XI
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
ABSTRACT
This dissertation is a part of the Louisiana NASA/EPSCoR (Experimental
Program to Stimulate Competitive Research) global change research, which
studied the fate of carbon and sediments within the Barataria Bay Basin,
Louisiana. It studied water composition to assess seawater influence within the
marsh. Ion exchange resin strips were used to study the effect of salinity and
Chloride (Cl) on sulfate (SO 4 ) reduction and their potential for water and soil
analysis. Chloride dominated the water system and the CI/SO 4 ratio can be
used to assess the seawater influence. Resin extractable sulfur (S) predicted
non-pyritic S fraction for the marsh soils. High salinity reduced the affinity of
target ions onto the resin. Limited affinity of SO 4 to resin indicates SO 4
accumulation within root zone, which promotes sulfate reduction and pyrite
formation.
This project mainly studied landscape position and salinity effects on
pyrite accumulation and the spatial variability of soil characteristics within a
saline and a brackish marsh. Salinity, pyrite, and non-pyritic iron (Fe) and 8
varied between streamside and inland. Depressions in mineral layer, accretion
variations and associated hydrology caused the field-scale variability. When
the inland site is landlocked, salinity and pyrite content within the surface
horizon varied. Non-pyritic 8 , pH, and pyrite profiles were different in different
marsh types. Mineralogical evidence also found for presence of pyrite
framboids. These soils should be reclassified to indicate accumulations of
reduced sulfur.
XII
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Thickness of subsurface horizons was highly spatially variable. Variation
in depth to mineral layer (DML) can be due to the presence of depressions in
the mineral layer surface. Typic Medisaprists occurred mostly toward inland
areas and away from waterways at the saline marsh. The DML was shallower
for the degrading marsh within the saline marsh type. Typic Medisaprists within
the brackish marsh had thick organic layers due to presence of thick
subhorizons. Spatial variability is evident for pH and organic/mineral ratio
(OMR) within organic subhorizons. The OMR data varied widely for the
brackish marsh compared to saline marsh. Organic soil characteristics vary
spatially due to variations in associated processes, therefore, spatial variability
should be considered for soil sampling schemes.
XIII
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CHAPTER 1: INTRODUCTION
A multidisciplinary research team was formed to study the fate of carbon
and sediments within the Barataria Bay Basin, Louisiana under the Louisiana
NASA/EPSCoR (Experimental Program to Stimulate Competitive Research)
global change research cluster (Miller et al., 1995). The research team
comprised of focus groups for hydrology, vegetation, biogeochemistry, soil
science, remote sensing and CIS. This dissertation is part of the soil science
investigations, which also includes studies required by the collaborations with
the hydrology and remote sensing groups.
Relationship between electrical conductivity (EC) and total dissolved
solids (TDS) is required for ground truthing the Airborne Electromagnetic
Profiler (AEM) data. The AEM data can be used to obtain material conductivity
and depth (Bergeron et al., 1989; Travis, 1994) The relationship between EC
and the elemental ratios may indicate the seawater influence and deviation of
the ratios may be used to determine flow direction within marsh for the
hydrology work.
Ion-exchange resin strips are used as a tool to analyze a large number
of samples quickly. Resin strips are very useful, if feasible, to use for water
samples as required by the hydrology studies and soil samples for sulfur (S)
estimations for the spatial variability studies. Currently available S fractionation
methods are complicated, laborious and time consuming (Begheijn, 1978; Lord
III, 1982; Raiswell et al., 1994). Resin extractable S needs to be calibrated for
different sulfur fractions of organic soil samples.
1
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Seawater brings in 8 as sulfate that is chemically reduced within the
anaerobic environment within the organic soils. This process is called sulfate
reduction that forms pyrite as an end product (Ponnamperuma, 1972; Patrick
and Jugsujinda, 1992; Rabenhorst and James, 1992). Coastal marsh provides
a suitable environment for pyrite formation because of the presence of
anaerobic environment, continuous S supply by seawater intrusion and the
availability of reduced iron (Pons et al., 1982). During the sulfate reduction
process, microorganisms utilize labile carbon as the energy source (Connell
and Patrick, 1969; Rabenhorst and James, 1992). The amount of pyrite
indirectly estimates the quantity of carbon utilized for the sulfate reduction.
Existence of the favorable conditions for the pyrite formation leads to
pyrite accumulation within the soil profile. However, the availability of easily
decomposable organic matter limits the sulfate reduction (Devai et al., 1996).
Reduction of ferric to ferrous, conversion of sulfate to different forms of reduced
sulfur and pyrite formation, occur in consequent steps. Therefore,
accumulations of pyrite, ferrous and sulfidic material within the soil profile reflect
the biogeochemical status of a marsh, which can be spatially variable. The
accumulation of sulfide is toxic to plants, but the presence of mineral material
buffers sulfide toxicity by soil iron (Koch and Mendelssohn, 1989; Nyman and
DeLaune, 1991). The accumulation of ferrous and sulfide reflects limited
pyritization due to the unavailability of labile carbon.
Previous 8 dynamics studies within these marshes have confined
sampling within close proximity to avoid spatial variability (Feijtel et al., 1988;
2
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Krairapanond et al., 1991a, 1991b, 1992). However, DeLaune et ai. (1983)
reported the existence of a sulfide concentration gradient associated with slight
elevation changes that resulted in plant productivity and mortality variations.
The elevation variations are controlled by the accretion rate. The vertical
accretion rates vary between levee areas and backmarshes (Hatton et al.,
1983). As the previous studies indicated the biogeochemical status of the soils
vary between landscape positions. Therefore, a detailed study is needed to
understand the spatial variability for profile distribution of S fractions between
landscape positions within different marsh types.
High net primary production of coastal marsh in terms of the above and
below ground biomass is the main contribution to the fixed carbon pool within
the marsh soil environment. The organic soil profile is comprised of mainly two
layers; the organic layer and the mineral layer. The organic layer can be
divided into different sub horizons based on the color and the composition. The
organic matter accumulation (organic accretion) and sedimentation (inorganic
accretion) are the main processes that form the organic sub horizons (Hatton et
al., 1983; Chmura et al., 1992;Nyman et al., 1993). Thickness of the organic
subhorizons varies due to the variations in the organic and the inorganic
accretions and disturbances to the marsh, which reflects the historical signature
of the marsh soil formation. Organic accretions vary due to the changes in the
productivity of the vegetation and inorganic accretions vary depending on the
changes in the sedimentation rate within the marsh.
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Marsh loss to open water is a severe problem in the marshes of northern
Gulf of Mexico (Boesch et al., 1983; Salinas et al., 1986; Turner, 1990).
Degradation and catastrophic events are the main disturbances to the marsh.
Two mechanisms, vegetation die back and subsurface erosion cause marsh
degradation. Vegetation die back is associated with plant stress due to sulfide
toxicity and flooding (Webb et al., 1995). Inability of the marsh to counter the
submergence level has been reported as the main cause of marsh loss (Turner,
1990; DeLaune et al., 1994). Subsurface erosion causes loss of organic
subhorizons and collapse of the surface organic layer (DeLaune et al., 1983;
DeLaune et al., 1994; Nyman et al., 1994). Salinity intrusion also causes
dispersion of sediments within the degrading marshes. In the submerging
marsh the organic matter is either buried within the profile or lost to the open
water areas (Nyman et al., 1995). Catastrophic events influence the Louisiana
marshes frequently. Hurricanes bring salt water and sediments inland and may
also erode lands due to physical action of flooding (Childers et al., 1990;
Turner, 1990; Jackson et al., 1995). Sedimentation due to hurricanes is highly
variably within the marsh (Nyman et al., 1995).
Information on spatial variability of coastal marsh characteristics is
limited at field scale. Soil sampling is very difficult within the marsh and spatial
variability data will help plan soil sampling schemes to be more representative
and minimize the number of sampling points as appropriate. Remotely sensed
data are often used in coastal marsh studies and the spatial variability
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
information also helps a researcher decide the appropriate pixel size of the
remotely sensed data for a particular study.
The thickness of the organic subhorizons is a direct estimate of fixed
carbon. The organic/mineral ratio and pH reflect the compositional and
biogeochemical status of the marsh. Understanding of the spatial variability of
these characteristics more accurately estimates the carbon pool within the
marsh.
Four studies are reported in this dissertation with the following
objectives. The linkage of the different studies is presented in Figure 1.1.
1. To estimate salinity parameters and elemental ratios for the estuarine water.
2. To study the feasibility of the ion-exchange resin strips for water analysis and
to estimate sulfur status.
3. To determine the effect of landscape position and marsh type on pyrite
accumulation.
4. To study the spatial variability of the coastal organic soil characteristics.
Study 1 establishes the relationships between the EC and the TDS and
the elemental ratios for the water system within the Barataria Bay, which is
mainly collaboration with the remote sensing and the hydrology groups. The
elemental ratios that are characteristic to the water system are identified and
their relationship with the EG is established. Based on this information any
deviation of water samples from their original composition is identified. This
scenario can be used to assess the influence of seawater intrusion and to
determine the flow direction of water within the marsh. The information on
5
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
:x)CD■oOQ.CgQ.
■oCD
C/)(/)o'=5
8 5c q '
3CD
C
CD■oOQ.CaO3■oO
&
oc■oCD
Chapter 1: Introduction
1
o>
Chapter 6: Conclusions
Chapter 2; Estimate salinity parameters and elemental ratios for the estuarine water (study 1 )
Chapter 5: Study the spatial variability of coastal organic soil characteristics (study 4)
Chapter 3: Study the feasibility of ion-exchange resin strips for water analysis and to estimate soil S status (study 2)
Chapter 4: Determination of the effect of landscape position and marsh type on pyrite accumulation (study 3)
C/)(/)o'3
Figure 1.1. Schematic representation of the linkage between different chapters of the dissertation
salinity and dominant ions is used as a guideline for testing resin strips for
water and soil analysis in study 2 and to select salinity levels for study 3.
Feasibility of resin strips is tested for the estuarine water and coastal
marshes in study 2. Several constraints for soil and water analysis can be
avoided using resin strips. Saline water samples can not be analyzed by
instruments such as Inductively Coupled Plasma (ICP-AES) and Ion
Chromatography (1C) because of the interference of high concentrations of
soluble salts. Dilution of samples reduces the target ions beiow the detection
limits of the instruments. Resin extractions enable one to use these
instruments despite the high salinity of the samples. Multi-elemental analysis
can be performed quickly using resin strips.
Bulk density of the marshes varies widely. Therefore, the elemental
concentration estimates can not be compared unless they are corrected for
bulk density of the soils. Resin strips mimic plant roots and resin extracted
elemental concentrations are independent from bulk density variations. It is
advantageous if we use resins for S analysis of coastal organic soils, especially
for spatial variability studies. Resin strips have never been tested for these
soils. W ater samples collected for study 1 were used to study the resin
performance for water analysis. The effect of salinity and Chloride (01) on the
affinity of target ions on to the resin is presented. Data on resin extracted S are
calibrated with water-soluble S and the pyritic and non-pyritic S data collected
for study 3.
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
The influence of the landscape position and marsh type on pyrite
accumulation, and non-pyritc Fe and S profiles is presented in the study 3.
The currently available pyrite determination methods are complicated, laborious
and time consuming (Begheijn, 1978; Lord III, 1982; Willett and Beech, 1987;
Leventhal and Taylor, 1990; Raiswell et al., 1994). A modified technique was
used to determine pyrite content indirectly (Schneider and Schneider, 1990). A
quick and easy method is necessary for spatial variability studies because of
the large number of samples needs to be tested. Moreover, the spatial
variability pattern is independent of the analytical technique used. Profile
distribution of pyrite and non-pyritic Fe and S were studied to determine
differences between landscape positions and marsh types.
The spatial variability of selected soil characteristics is presented in
study 4. Two sites representing a saline and a brackish marsh were intensively
sampled on a grid within a one-square mile area. Soil morphological data such
as sub horizon thickness, depth to mineral layer, pH and organic/mineral ratio
for different horizons were collected. Geostatistical analysis was conducted to
identify the spatial variability of the soil variables. The semivariograms are
presented for the soil variables and future marsh sampling schemes can be
planned on the spatial variability data. Data are interpolated within a one-
square mile area on a finer grid using appropriate interpolation methods to
identify associated landscape patterns of these soil characteristics.
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
1.1 ReferencesBegheijn, L. Th., N. van Breemen, and E. J. Velthorst. 1978. Analysis of sulfur
compounds in acid sulfate soils and other recent marine soils. Commun, in Soil Soi. Plant Anal. 9(9):873-882.
Bergeron, Jr., C. J., J. W. loup, and G. A. Michel, II. 1989. Interpretation of airborneelectromagnetic data using the modified image method. Geophysics. 54(8):1023-1030.
Boesch, D. P., Levin, D., Nummedal, D., and Bowles, K. 1983. Subsidence in coastal Louisiana: Causes, Rates, and Effects on Wetlands. U. S. Fish and Wildlife Service FWS/OBS-83/26, Washington, D. 0., 30pp.
Childers, D. L., J. W. Day, and R. A. Muller. 1990. Relating climatological forcing to coastal water levels in Louisiana estuaries and the potential importance of El Nino-Southern oscillation events. Climate Research 1:31-42.
Chmura, G. L., R. Costanza, and E. Kosters. 1992. Modelling coastal marsh stability in response to sea level rise: a case study in coastal Louisiana, USA. Ecological Modelling, 64:47-64.
Connell, W. E., and W. H. Patrick, Jr. 1969. Reduction of sulfate to sulfide in waterlogged soil. Soil Soi. Soc. Am. Proc. 33:711-715.
DeLaune, R. D., R. H. Baumann, and J. G. Gosselink. 1983. Relationships among vertical accretion, coastal submergence, and erosion in a Louisiana gulf coast marsh. Journal of Sedimentary Petrology 53(1 ): 147- 157.
DeLaune, R. D., C. J. Smith., and W. H. Patrick. 1983. Relationship of marsh elevation, redox potential, and sulfide to Spartina a Item if I ora productivity. Soil Sci. Soc. Am. J. 47:930-935.
DeLaune, R. D., J. A. Nyman, and W. H. Patrick, Jr. 1994. Peat Collapse, ponding and wetland loss in a rapidly submerging coastal marsh. J. Coastal Res. 10:1021-1030.
Devai, I., K. R. Reddy, R. D. DeLaune, and D. A. Graetz. 1996. Sulfatereduction and organic matter decomposition in a wetland soil and lake sediment. Acta Biol. Debr. Oecol. Hung. 6:13-23.
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Feijtel, T. C., R. D. Delaune, and W. H. Patrick, JR. 1988. Seasonal pore water dynamics In marshes of Baratarla Basin, Louisiana, Soli Sol. Soc. Am. J. 52:59-67.
Hatton, R. S., R. D. DeLaune, and W. H. Patrick, Jr. 1983. Sedimentation accretion, and subsidence In marshes of Baratarla Basin, Louisiana. Limnology and Oceanography 28:494-502.
Jackson, L. L., A. Lee Foote, and L. S. Ballstrlerl. 1995. Hydrological,geomorphologlcal, and chemical effects of hurricane Andrew on coastal marshes of Louisiana. Journal of Coastal Research SI(21):306-323.
Koch, M. S. and I. A. Mendelssohn. 1989. Sulphide as a soil phytotoxin: Differential response In two marsh species. J. Ecol. 77:565-578.
Kralrapanond, N., R. D. DeLaune, and W. H. Patrick, JR. 1991a. Sulfur dynamics In Louisiana coastal freshwater marsh soils. Soil Sol. 151(4):261-273.
Kralrapanond, N., R. D. DeLaune, and W. H. Patrick, JR. 1991b. Seasonal distribution of sulfur fractions In Louisiana salt marsh soils. Estuaries 14:17-28.
Kralrapanond, N., R. D. DeLaune, and W. H. Patrick, JR. 1992. Distribution of organic and reduced sulfur forms In marsh soils of coastal Louisiana,Org. Geochem. 18:489-500.
Leventhal, J., and C. Taylor. 1990. Comparison of methods to determinedegree of pyrltlzatlon. Geochlmica et Cosmochlmica Acta 54:2621-2625.
Lord III, C. J. 1982. A selective and precise method for pyrite determination In sedimentary materials. Journal of Sedimentary Petrology 52:664-666.
Miller, R. L., M. Glardino, B. A. McKee, J. F. Cruise, G. Booth, R. Rovansek, D. Mulrhead, W . CIbula, K. Holladay, R. E. Pelletier, W . Hudnall, C. Bergeron,J. loup, G. loup, and G. Love. 1995. Processes and fate of sediments and carbon In Baratarla Bay, LA. Proceedings from the Third Thematic Conference on Remote Sensing for Marine and Coastal Environments. Seatle, Washington. Vol. l:233-244pp.
Nyman, J. A. and R. D. DeLaune. 1991. Mineral and organic matteraccumulation rates In deltaic coastal marshes and their Importance to landscape stability. GCSSEPM Foundation Twelfth Annual Research Conference Program and Abstracts, 166-170.
10
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Nyman, J. A., M. Carlose, R. D. DeLaune, and W . H. Patrick, Jr. 1994.Erosion rather than plant dieback as the mechanism of marsh loss in an estuarine marsh. Earth Surface Processes and Landforms 19:69-84.
Nyman, J. A., J. C. Callaway, and R. D. DeLaune. 1993. Case study of a rapidly submerging coastal environment: relationships among vertical accretion, carbon cycling and marsh loss in the terrebone basin, Louisiana. Proceedings of the Hilton Head Island South Carolina USA International Coastal Symposium, June 6-9, 1993. vol 2. 452-457p.
Nyman, J. A., R. D. D elaune, S. R. Pezeshki, and W. H. Patrick, Jr. 1995. Organic matter fluxes and marsh stability in a rapidly submerging estuarine marsh. Estuaries 18:207-218.
Patrick, W. H. Jr., and A. Jugsujinda. 1992. Sequential reduction and oxidation of inorganic Nitrogen, Manganese, and Iron in flooded soil. Soil Soi. Soc. Am. J. 56:1071-1073.
Ponnamperuma, F. N. 1972. The chemistry of submerged soils. Adv. Agron. 24:29-96.
Pons, L. J., N. van Breemen, and P. M. Driesses. 1982. Physiography ofcoastal sediments and development of potential soil acidity, pp. 1-18. In J. A. Kittrick, D. S. Fanning, and L. R. Hossner (Eds.) Acid sulfate weathering. Soil Sci. Soc. Am. Spec. Pub. No. 10, Soil Sci. Soc. Am., Madison, Wisconsin.
Rabenhorst, M. C., and B. R. James. 1992. Iron sulfidization in tidal marsh soils. In H. C. W. Skinner and R. W. Fitzpatrick (Eds.) Biomineralization processes. Iron, Manganese: modern and ancient environments. Catena supplement 21:203-217.
Raiswell, R., and D. E. Canfield, and R. A. Berner. 1994. A comparison of iron extraction for determination of degree of pyritisation and the recognition of iron-limited pyrite formation. Chemical Geology 111:101-110.
Salinas, L. M., R. D. D elaune, and W . H. Patrick, Jr. 1986. Changes occuring along a rapidly submerging coastal area: Louisiana, USA. Journal of Coastal Research 2(3):269-284.
Schneider, J. W ., and K. Schneider. 1990. Indirect method for thedetermination of pyrite in clays and shales after selective extraction with acid solutions. Ceramic Bulletin 69(1): 107-109.
11
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Travis, R. E. P. 1994. Utility of remote sensing technology in wetland soil and gas flux studies. A Dissertation submitted to Louisiana State University, La.
Turner, R. E. 1990. Landscape development and coastal wetland losses in the northern Gulf of Mexico. Amer. Zool. 30:89-105.
Webb, E. C., I. A. Mendelssohn, and B. J. Wilsey. 1995. Causes for vegetation dieback in a Louisiana salt marsh: A bioassay approach. Aquatic Botany 51:281-289.
Willett, I. R., and T. A. Beech. 1987. Determination of organic carbon in pyritic and acid sulfate soils. Commun, in Soil Sci. Plant Anal. 18(7):715-724.
12
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CHAPTER 2: ESTIMATE SALINITY PARAMETERS AND ELEMENTAL RATIOS FOR THE ESTUARINE WATER SYSTEM OF BARATARIA BAY
BASIN2.1 Summary and Introduction
This study establishes the relationships between the electrical
conductivity (EC) and the total dissolved solids (TDS) and the elemental ratios
for the water system within the Barataria Bay Basin. Water samples from the
Baratarla Bay Estuary were analyzed for chemical properties. Salinity and the
elemental ratios were studied. Barataria Bay estuary has a chloride dominant
water system with a wide range of salinity. The elemental composition and the
ionic ratios indicate that the water characteristics of this estuary are extensively
under the influence of seawater intrusion. Salinity change is due to the mixing
of seawater with fresh water, because the ratios of major elements are similar
to that of seawater. The chloride/sulfate ratios indicate that seawater intrusion
controls the salinity within the brackish and saline marshes while the fresh
marsh is free from seawater salinity. The deviation in elemental ratios of water
samples from the seawater ratios can be used to assess the influence of
seawater intrusion and to determine the flow direction of water within the
marsh. Chloride/sulfate ratio is proposed to determine the extent of seawater
intrusion within the basin. The information on salinity and dominant ions is
used as a guideline for testing resin strips for water and soil analysis in study 2
in this dissertation.
13
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
A multidisciplinary research team was formed to study the fate of carbon
and sediments within the Barataria Bay Basin, Louisiana under the Louisiana
NASA/EPSCoR (Experimental Program to Stimulate Competitive Research)
global change research cluster (Miller et al., 1995). The research team
comprised of focus groups for hydrology, vegetation, biogeochemistry, soil
science, remote sensing and GIS. This study is required by the collaborations
with the hydrology and remote sensing groups. Airborne electromagnetic
profiler (AEM) is used to remotely collect data on salinity and organic layer
thickness within the marsh. The AEM data can be used to obtain material
conductivity and depth (Bergeron et al., 1989; Travis, 1994). Relationship
between EC and TDS is required for ground truthing the AEM data. The
relationship between EC and the elemental ratios may indicate the seawater
influence within the marsh.
Characterization of the chemical properties of the estuarine water
system helps to compare the data with other estuarine systems as well as to
use the knowledge generated from other estuaries. Seawater is considered as
the main source of sulfur in to the marsh ecosystem. Sulfate reduction is a
major biogeochemical process within the marsh, which is mainly responsible for
S transformations within the soils and sediments. Biological S assimilation
converts the inorganic S in to organic S forms. Plants respond to high soluble
salt concentrations within the root zone through different mechanisms such as
ion exclusion, secretion and accumulation. Overall salinity controls these
mechanisms within the plants and the species responses are different (Bradley
14
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
and Morris, 1991; Latham et al., 1994). Ionic ratios may be changed in water
due to these biological and geochemical processes.
Deviation of elemental ratio may indicate lack of seawater influence or
domination of another process. Hydrological studies need flow rate
measurements along the flow path to determine the direction of water flow.
Within the seawater influenced areas the deviation of the elemental ratios may
be used to determine flow direction within marsh for the hydrology work. This
study was planned mainly to provide information for the collaborative work
within the NASA/EPSCoR project. Therefore, it will measure the elemental
composition of the estuarine water at different salinity levels and establish the
relationship between EC and TD S for this water system.
2.2 Literature Review
2.2.1 Barataria Bay Basin Water System
The study was carried out in Barataria Bay Basin, which is a shallow
coastal estuary in Louisiana. The natural levees of the Mississippi River
constitute its northern and eastern boundaries while the abandoned Bayou
Lafourche distributory marks the western boundary. The Gulf of Mexico forms
the southern boundary (Figure 2.1). The basin is triangular in shape, about 110
km long and 50 km wide at the southern boundary (Conner and Day, 1987).
The total area of 628,000 ha is divided into three sub basins; upper freshwater
lake (Lac Des Allemands), middle brackish lakes, and lower saline bays
(Barataria Bay and Caminada Bay), lakes and marshes (Madden et al., 1988).
15
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD■ D
OQ.C
sQ.
■DCD
C/)C/)
8■D
oi«oo' 90 * 30 ' 90 * 00 ' 89 * 30 '
3.3 "CD
CD■DOQ.C
aO3"Oo
CDQ.
■DCD
C /)C /)
30 * 00 ' ____
G)
29 * 30 ' -
BARATARIA BASINLoulsiena
\Barataria Rasln
VegetationNolural lovaet(Urban, Agricultural Areoi
end Bollomlond Hardwood Pareil)
I Foreiled Welland (Swomp)
freih Morih
^ .1 Inlermediola Morih
I \ 1 Brockiih Morih
I Solina Morih
Figure 2.1 A map showing different marsh types within the Barataria Bay Basin (after Kralrapanond et al., 1992)
Salinity varies within the Barataria Bay Basin and this spatial variability has
established a well-defined salinity and vegetation association. Salinity
determines the vegetation type and influences pedogenic processes. Marshes
are delineated into saline, brackish, intermediate, and fresh water marshes
based on the salinity levels. Salinity ranges from below 0.5 to above 20.0 ppt
within the Barataria Bay marshes. Fresh and intermediate marshes occur
below 5 ppt. Brackish marshes occur between 5 and 10 ppt while salt marsh is
found at salinity above 10 ppt (Feijtel et al., 1988; Soil Conservation Service,
1989). Seawater is considered as the main source of salt into the system. The
presence of channels and streams brings seawater into the inland marshes.
Channel construction has changed the natural hydrology and affected the water
characteristics. Even though the magnitude of salinity change is not well
estimated, studies have shown a gradual increase of salinity in this region (U.
S. Army Corp Engineers, 1984). Seasonal variations in salinity and sediment
concentrations were associated with short and long term weather changes.
Fresh water floods lowered salinity within the lower basin. Lake Salvador and
Barataria Waterway transfer sediments and water in both directions with the
influence of weather events (Garrepally, 1994). Hydrology information for this
basin are reported elsewhere (Garrepally, 1994; Rovansek, 1997).
17
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
2.2.2 Seawater Salinity, the Major Elements, and Salinity Parameters
The major ions of seawater are those that significantly contribute to the
measured salinity. In practice, the elements that are present at concentrations
greater than 1 mg L' are considered as major ions except silicon (Si) which is
conventionally excluded because of its atypical ionic behavior. The major
cations are Na. K, Mg, Ca, and Sr while the major anions include Cl, SO4, Br, F,
and B. The major ions are referred to as conservative because their
concentrations in seawater maintain a constant ratio, one to another. This
constancy of composition of seawater permits the use of salinity to describe the
salt in a seawater sample. This uniqueness is so important that the ratios can
be used to compare compositional differences in sea salt from various parts of
the world (Wilson, 1975). The most important water quality parameter in
relation to salinity is the total salt content that is expressed as TDS. The TDS
can be determined gravimetrically. Measuring TDS is more tedious than
measuring EC, which is the currently preferred measure of salinity (Bresler et
al., 1982). Gravimetric estimates may not be accurate due to the volatility of
some inorganic constituents and possible retention of water of crystallization
(Wilson, 1975; Bresler et al., 1982). However, the gravimetric method is used
when an empirical relationship needs to be defined. The relationship
developed by Forch and others (Wilson, 1975), Salinity (ppt) = 1.805 Cl (ppt) +
0.030, was later replaced by Salinity (ppt) = 1.80655 Cl (ppt) due to
improvements in instrumentation and considering the variability of different
18
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
seawaters. The EC can be converted to TDS through the approximate
relationship proposed by the U. S. Salinity Laboratory Staff (within the EC
range of 3 to 30 dS m'^) (Bresler at al., 1982); TDS (mg L'^) = 0.64 * 10^ EC
(dS m'^). Seawater salinity is commonly considered as 35 ppt. The ratios of
cations (ppt) to chloride (ppt) were reported by Wilson (1975); Na, 0.5555; K,
0.0206; Mg, 0.06625; Ca, 0.02126; and Sr, 0.00041. The ratio of SO 4 to
chloride is 0.14. Average B content is about 4 .5 mg L' at sea water salinity of
35 ppt and its chloride concentration is about 19.354 g kg‘ (Wilson, 1975).
These chemical ratios can be used as a scheme to characterize the estuarine
water.
2.3 Materials and Methods
2.3.1 Sample Collection and Preparation
W ater samples were collected from different water bodies within brackish
and saline marsh areas of the Barataria Bay Basin during the summers of
1995, 1996, and 1997. Geographic locations were registered using a Global
Positioning System (G PS) for most of the sample locations. Table 2.1 provides
several sample locations with their coordinates and their electrical conductivity.
W ater samples were also collected from small streams or broken marsh areas
within the inland marshes. W ater samples were brought to the laboratory in an
ice-filled cooler and filtered (Whatman No. 42). These samples were used to
measure EC, pH and elemental composition.
19
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD■ D
OQ.C
gQ.
■DCD
C/)C/)
8■D
■DCD
C /)C /)
Table 2.1. Sample locations and EC measurements.
3.3 "CD
^ ëOQ.C
a.O3"OO
CDQ.
Sample Latitude / Longitude EC (dS m" ) Sample Latitude / Longitude EC (dS m-1)
1 29 24.308 / 90 04.024 06.11 25 29 3 1 .2 5 2 /9 0 01.977 05.372 29 2 4 .2 1 0 /9 0 03.962 05.39 26 29 2 9 .6 9 7 /9 0 01.173 07.193 29 23.889 / 90 03.976 05.05 27 29 1 4 .7 4 9 /9 0 07.270 38.614 29 22.245 / 90 03.879 11.28 28 29 1 4 .7 4 9 /9 0 07.270 38.905 29 2 1 .1 3 8 /9 0 04.228 14.77 29 29 1 6 .5 8 7 /9 0 08.182 34.906 29 20.428 / 90 03.968 14.81 30 29 1 6 .5 8 7 /9 0 08.182 38.507 29 1 9 .2 4 4 /9 0 02.020 18.58 31 29 1 6 .5 8 3 /9 0 08.167 26.308 29 1 8 .8 0 2 /9 0 04.381 21.40 32 29 1 6 .5 8 3 /9 0 08.167 27.809 29 2 0 .0 1 8 /9 0 06.282 24.86 33 29 1 6 .5 8 3 /9 0 08.167 29.501 0 29 20.558 / 90 05.272 19.68 34 29 1 6 .5 8 3 /9 0 08.167 27.201 1 29 1 9 .9 8 7 /9 0 07.254 28.02 35 29 24.204 / 90 03.306 19.381 2 29 20.857 / 90 08.370 22.54 36 29 24.204 / 90 03.306 20.6013 29 23.495 / 90 06.628 16.59 37 29 2 4 .2 1 0 /9 0 04.024 19.2414 29 23.245 / 90 01.737 09.87 38 29 2 4 .2 1 0 /9 0 04.024 17.8615 29 24.308 / 90 04.024 06.56 39 29 23.560 / 89 56.500 48.3916 29 24.558 / 90 03.177 06.73 40 29 23.700 / 89 58.700 40.6017 29 2 4 .1 5 2 /9 0 01.684 10.60 41 29 2 4 .1 7 4 /9 0 03.930 42.1018 29 2 3 .7 7 5 /9 0 01.710 10.73 42 29 24.038 / 90 03.382 45.0019 29 23.885 / 90 02.921 06.71 43 29 4 1 .3 0 0 /9 0 12.090 06.822 0 29 23.869 / 90 03.894 05.80 44 29 45.101 /9 0 21.500 0.1932 1 29 2 4 .1 7 4 /9 0 03.930 06.08 45 29 45.101 /9 0 21.500 0.5892 2 29 24.305 / 90 04.067 05.60 46 29 45.101 /9 0 21.500 0.78723 29 24.305 / 90 04.067 09.71 47 29 45.101 /9 0 21.500 0.15624 29 24.204 / 90 03.306 10.08 48 29 45.101 /9 0 21.500 0.144
2.3.2 Chemical Analysis
The EC of the water samples was measured using a Corning M90
conductivity sensor (Corning Inc., Corning New York 14831, USA). The pH
was measured in the laboratory using a combination pH electrode, and chloride
was measured using a chloride ion selective electrode with pH/m V meter (Orion
Research model 701A/digital lONALYZER). Chloride concentration data were
obtained from a linear calibration using 1 0 to 1 0 0 0 0 ppm chloride
concentrations. W ater samples were analyzed using ICP-AES (PERKIN
ELMER model OPTIMA 3000 (Perkin-Elmer Corporation, Norwalk, CT 06859,
USA). Chloride can be estimated from charge balance calculations when
sulfate content is known (Wilson, 1975; Bresler et al., 1982). This uses two
assumptions that are very feasible; total halides are replaced by chloride and all
the sulfur is in an inorganic form.
2.3.3 Measurement of TDS
A volume of 30 - 60 mL from each water sample was weighed and slowly
evaporated in a centrifuge tube at a temperature between 55 - 65 °C in an
oven, cooled in a desiccator and weighed. The TDS was estimated on a dry
weight basis for each sample in triplicate. Total solids in solution were also
estimated based on chemical composition, by adding all the major cations and
anions.
21
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
2.4 Results and Discussion
2.4.1 Elemental Composition
Concentrations of major cations and anions and their relationship with
electrical conductivity are presented. Elemental concentrations changed
drastically between fresh water and saline water marshes. Descriptive statistics
for elemental composition of water samples are presented in Table 2.2. More
attention is given to the ranges than the mean values because the low
concentrations of fresh water lowered the means. W ater samples were not
collected systematically so that they may or may not have included any
temporal variability in addition to the spatial variability.
EC of water samples ranged from 0.144 to 48.39 dSm'^ (Table 2.2). EC
of water samples from fresh marsh ranged from 0.144 to 0.787 d S m '\ higher
values were obtained for standing water (i.e., 0.787) within the marsh while the
EC of the water in the bayou was less than 0.2 dSm "\ W ater samples from
brackish and saline areas always had greater EC values than water samples
from the fresh marsh. The pH of the water samples ranged between 6.69 and
8.29; pH increased with increasing EC.
Chloride concentrations increased about 300 times from fresh to saline
marshes (Table 2.2). Within the fresh marshes, Cl concentration ranged from
42 to 227 mg L ' \ the bayou water had lower concentrations (42 to 44 mg L'^)
while standing water within the marsh had Cl concentrations ranging from 179
to 227 mg L ' \ Brackish and saline areas had chloride concentrations ranging
22
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD■ D
OQ.C
gQ.
■DCD
(/)Wo"303CD
8■D( O '3"
13CD
3.3 "CD
CD■DOQ.C
aO3
■DO
CDQ.
"DCD
roco
Table 2.2 Electrical conductivity, pH and elemental concentration ranges of water samples.
Descriptive
Statistics
EC pH Cl
Element concentration^
--------------------- (mg L ' ) --------------
SO4 B Na Mg Ca K Sr
Mean 20.39 7.66 6319 888.28 1.72 3501.3 412.25 144.95 126.71 2.271
80+ 12.79 0.385 3867 570.51 1.086 2160.5 252.97 81.1 76.46 1.530
Minimum 0.144 6.69 41.9 3.86 0.0323 7.04 3.83 10.46 1.78 0.051
Median 21.15 7.715 6285.5 884.03 1.5372 3491.6 409.76 143.87 121.34 2.226
Maximum 48.39 8.29 13356.9 2232.1 6.3135 7423.7 878.18 293.5 267.5 5.098
50 samples: Standard Deviation
3(/)o'
from 1919 to 13357 mg L ' \ Sulfate concentration In fresh water ranged from
about 4 to 14 mg L' whiles In saline and brackish areas sulfate concentrations
ranged 223 to 2232 mg L ' \
Sodium was the dominant cation. Its concentration ranged from 797 to
7424 mg L' In brackish and saline waters. The samples contained more Mg
than Ca and K, and Mg concentration ranged from 4 to 878 mg L ' \ with
concentrations less than 16 mg L' for the fresh water. Concentration of Ca
and K were similar but Ca was always higher. Boron concentrations ranged
from 0.7 to 6.3 mg L' while Sr concentrations ranged from 0.7 to 5.1 mg L" In
brackish and saline water (Table 2.2).
2.4.2 Electrical Conductivity and Elemental Concentrations
The relationships between EC and cations are presented In Figure 2.2.
Cation concentrations Increased linearly with Increasing EC. Sodium Is the
dominant cation In water samples. Calcium and K were found In equal
concentrations but Mg concentration was higher than Ca and K. The following
regression equations were obtained between the EC (dSm'^) and the cation
concentrations In mg L '\
Na = 1 6 5 * E C + 136.50 (R^ = 0.954) [1]
Mg = 19.342 * EC + 17.82 (R^ = 0.956) [2]
Ca = 6 . 1 4 * E C + 19.75 (R^ = 0.937) [3]
K = 5.742 * EC + 9.62 (R" = 0.922) [4]
24
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD■ D
OQ.C
gQ.
■DCD
C/)C/)
8■D
3.3 "CD
CD■DOQ.C
aO3"OO
CDQ.
■DCD
N)en
gc01'c8coüco%o
8000
7000
6000
5000
4000
3000
2000
1000
0
ONa
+ Mg
o Ca
A K
OO
° ° ° oo _c%o
+ + + + + +
0 10 20 30 40 50
Electrical Conductivity (dS m’ )
Figure 2.2. Electrical conductivity and the major cations of water samples.
C /)C /)
The relationship for EC and 01 concentration is presented in Figure 2 .3 and EC
and SO4 concentration is presented in Figure 2.4. Both Cl and SO4
concentration increased linearly with increasing EC and can be predicted from
following regression equations.
Cl = 2 9 5 * E C + 303 (R" = 0.952) [5]
SO 4 = 43.35 * EC + 4.21 (R" = 0.944) [6 ]
Chlorinity (Cl (%o)) is highly related with salinity, the relationship produced the
following equation that is very similar to that of seawater.
S (%o) = 1.81057 * Cl (%o) - 0 .045176 (R" = 0.999) [7]
The 95% confidence interval is indicated for equation [5] for Cl (Figure 2.3) and
for equation [6 ] for SO4 (Figure 2.4). At a particular EC value if the elemental
concentration (for Cl or SO4) is out of the confidence inten/al, the elemental
concentration that sample is significantly different from the common sample.
This indicates the water samples is not under the influence of seawater
intrusion. This can happen due to concentration of or depletion of the element
within more saline water system. In less saline areas this deviation can simply
indicate lack of seawater intrusion and influence of freshwater system.
2.4.3 Elemental Ratios
Elemental ratios have been used to characterize seawater. These ratios
may also be appropriate indicators for estuarine water characterization.
Relative concentration of other major elements to chloride concentration is
widely used. Element/chloride ratios for the water samples are presented in
26
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD■ D
OQ.C
gQ.
■DCD
C/)C/)
8■D
3.3 "CD
CD■DOQ.C
aO3"OO
CDQ.
S
16000
14000
12000
g 10000c° 8000 co 6000
8ü 4000
d & o
(D) < 0 0
2000
20 3010 40 50
Electrical Conductivity (dS m )
■DCD
C /)C /)
Figure 2.3. Upper and lower confidence intervals (95%) for Cl concentration at different EClevels.
CD■ D
OQ.C
gQ.
■DCD
C/)C/)
8
ci'
33 "CD
CD■DOQ.C
aO3"OO
CDQ.
■DCD
ro00
3000
g 2000CO
Isc8 1000
ow
10 20 30 40 50
Electrical Conductivity (dS m’ )
Figure 2.4. Upper and lower confidence intervals for SO4 concentration at different EC levels.
C /)C /)
Table 2.3, together with ratios for standard seawater at 35%o (SO 4 /Cl, 0.14;
Na/CI, 0.5555; Mg/Cl, 0.06625; Ca/CI, 0.02126; K/CI, 0.0206). Mean SO 4 /CI
ratio was 0.1342, which is close to the ratio for seawater. This measured ratio
was unchanged within the brackish and saline waters. However the S 04 /C I
ratio decreased within the fresh water to 0.0631, suggesting depletion of sulfate
once the water gets into the fresh marsh. Other elemental ratios were also
found close to those of seawater values; mean ratios for Na, 0.5283; Mg,
0.0664; Ca, 0.0394; and K, 0.0228 (Table 2.3).
Figure 2.5 presents the relationship between EC and CI/SO4 ratio. For
seawater at 35%o this ratio is about 7.0. For the water samples from brackish
and saline areas this ratio ranged between 6 and 8 while for the fresh marsh
this ratio was higher and ranged between 9 and 16. Higher Cl content
associated with standing water samples may be due to the concentration effect.
However, it should be noted that the total salts in the fresh water samples are
very low. Chloride was dominant and contributed 56.0% of salinity compared to
SO4 that contributed 7.5 % and the balance (36.5% ) were major cations.
Considering the salt composition data, it may be inferred that the seawater
influence within the Barataria Basin is very extensive because about 50 water
samples collected randomly over a three-year period had the similar salt
composition.
When CI/SO4 ratio data were separated to represent different marsh
types based on their EC, it is evident that the ratios are always higher for the
29
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD■ D
OQ.C
8Q.
■DCD
C/)Wo"303CD
8■D( O '3"
13CD
3.3 "CD
CD■DOQ.C
aO3
"D
O
CDQ.
■DCD
Table 2.3 Element/chloride ratios of water samples.
03o
Descriptive
Statistics
SO4 /CI B/CI
Elemental Ratio”
Na/CI Mg/Cl Ca/CI K/CI Sr/Cl
Mean 0.1343 0.000281 0.52827 0.06644 0.03940 0.02284 0.000473
SD^ 0.0198 0.000099 0.08251 0.00633 0.05390 0.01090 0.000224
Minimum 0.0631 0.000175 0.1681 0.05046 0.02143 0.00785 0.000377
Median 0.1398 0.000245 0.5524 0.06536 0.02292 0.02032 0.000396
Maximum 0.1804 0.000771 0.5710 0.09138 0.27830 0.07772 0.001330
Seawater^ 0.14 N/A 0.5555 0.06625 0.02126 0.0206
3(/)Wo'
^50 samples; Standard Deviation; ^Seawater at 35%o (Wilson, 1975)
8 )
oLO
o
oco
oCM
coS
■I3TJC0 üs
1 (D
CM 00 O "
O Ü B jj l 'o s /1 0
0Q .Em(/)
10LUT3Cco
1o0s1coC01
lOc\iÿ.3.5)u_
31
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
fresh marsh (Figure 2.5). The mean CI/SO4 ratio values for different marsh
types are presented in Figure 2.6, the ratio for the fresh marsh is significantly
different from other marsh types. This can simply indicate that seawater mixing
does not extend in to the fresh marsh area because the seawater is highly
diluted. Lower S concentrations may be a result of S assimilation by plants and
S transformations within the soil. Sulfur use may be promoted within the fresh
marsh due to very low ionic competition. Rainwater can deposit considerable
amounts of Cl within the coastal areas (Berner and Berner, 1996). The 01
deposition by the rainwater may considerable change the CI/SO4 ratio at the
lower salinity levels within the fresh marsh. Both these mechanisms can result
higher CI/SO4 ratio. The ratio between SO4 and 01 can be used to determine
the extent of seawater intrusion within the basin and also to identify dominant
processes within the marsh. Therefore, OI/SO4 ratio in pore water and standing
water within the marsh may be different from the bay water.
2.4.4 Electrical Conductivity and Salinity
The relationship between electrical conductivity in dSm'^ and total
dissolved solids in ppt, was constructed based on the gravimetric method
(Figure 2.7) and on the elemental analysis data (Figure 2.8). Chlorine was
estimated based on charge balance calculations. The following relationships
were identified using the regression analysis.
Gravimetric method:
TD S = 0.669 * EC - 0.6208 (R" = 0.960) [8 ]
32
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD■ D
OQ.C
gQ.
■DCD
C/)(/)
8■D
3.3 "CD
CD■DOQ.C
ao3T3O
(DQ .
T3(D
(/)(/)
COCO
a:
oü
14
12
10
8
6
4
2
0FM IM BM SM
Marsh Type
Figure2.6. Chloride/sulfate ratio data for different marsh types (differnet letters indicatesignificant difference at a=.05).
in
CO
COo8 _ O CO I O)
oo to o o toto inCO CO CM CM
bdd) SP!|0S P0AIOSS1Q |B}01
COs
I3■oco0
81 (ULU
COQI -T3CmÜLU
(D
COco%20)jC
r-CM
23O)
34
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD■ D
OQ.C
gQ.
■DCD
C/)C/)
8■D
3.3 "CD
CD■DOQ.C
aO3"Oo
CDQ.
■DCD
Ü1
Q .
(/>;d■5CO"O>8
I
30
Y= 0.524X + 0.664225
[r = 0.9453]
200 0
15
10
5
00 10 20 30 40 50
Electrical Conductivity (dS m" )
Figure 2.8. The relationship between EC and JDS.
C /)C /)
Elemental composition:
TDS = 0.524 * EC + 0.6642 (R== = 0.945) [9]
However, the gravimetric method based relationship seems to be similar to the
relationships reported by the U. S. Salinity Laboratory Staff. It should be
cautioned when these relationships are used for lower EC levels such as below
3 dS m' (B reslereta l., 1982).
2.5 Conclusions
Barataria Bay estuary has a chloride dominant water system with a wide
range of salinity. The elemental composition and the ionic ratios indicate that
the water characteristics of this estuary are extensively under the influence of
seawater intrusion. Salinity changes are due to the dilution effect because the
ratios of major elements and chloride were similar to that of seawater.
Seawater intrusion widely controls the salinity within the brackish and saline
marshes but not in the fresh marsh. Sulfate/Chloride ratio is proposed to
estimate the extent of seawater intrusion within the basin and the water flow
within the marsh.
2.6 ReferencesBerner, E. K. and R. A. Berner. 1996. Global Environment: water, air, and
geochemical cycles. Prentice Hall Press, Upper Saddle River, New Jersey. 68-85p.
Bradley, P. M. and J. T. Morris. 1991. Relative importance of ion exclusion, secretion and accumulation in Spartina altem iflora Loisel. J. Expl. Bot. 42(245): 1525-1532.
36
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Bresler, E., B. L. McNeal, and D. L. Carter. 1982. Saline and sodic soils: principles-dynamics-modeling. Adv. Ser. Agric. Sci. 10: 1-27.Spring- Verlag, Ne\w York.
Conner, W . H., and Day, Jr., J. W. 1987. The ecology of Barataria Bay Basin: An estuarine profile. Biological Report 85:1-7.
Feijtel, T. C., R. D. DeLaune, and W. H. Patrick, JR. 1988. Seasonal porewater dynamics in marshes of Barataria Basin, Louisiana, Soil Sci. Soc. Am. J. 52:59-67.
Garrepally, R. R. 1994. Spatial and temporal variability in flow, salinity and sediment concentrations in Barataria Bay basin, Louisiana. A masters project report submitted to Louisiana State University and A and M College. 60pp.
Krairapanond, N., R. D. DeLaune, and W. H. Patrick, JR. 1992. Distribution of organic and reduced sulfur forms in marsh soils of coastal Louisiana, Org. Geochem. 18(4):489-500.
Latham, P. J., L. G. Pearlstine, and Wiley M. Kitchens. 1994. Speciesassociation changes across a gradient of freshwater, oligohaline, and mesohaline tidal marshes along the lower savannah river. Wetlands. 14(3):174-183.
Madden, C. J., J. W. Day Jr., and J. M. Randall. 1988. Freshwater and marine coupling in estuaries of the Mississippi River deltaic plain. Amer. Soc. Limnol. And Oceanogr. 33:982-1004.
Rovansek, R. J. 1997. Waterborne materials exchange between marshes and open water of the Barataria Bay estuary of Louisiana, U. S. A. A dissertation submitted to Louisiana State University and A and M College. 158pp.
Soil Conservation Service (SCS). 1989. East Central Barataria cooperative river basin study, Jefferson, Orleans, Plaquemines and St. Charles Parishes, Louisiana. Rev. May 1989. United States. Soil Conservation Service. National Cartographic Center (U.S.). Ft. Worth, TX : USDA-SCS-National Cartographic Center ; [Alexandria, La. State Conservationist, distributor].
U. S. Army Corp Engineer District, New Orleans. 1984. Louisiana coastal area study. New Orleans, La.
37
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Wilson, T. R. S. 1975. Salinity and the major elements of sea water, In J. P. Riley and G. Skirrow (eds.) Chemical Oceanography. 365-408p.
38
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CHAPTER 3: USE OF ION-EXCHANGE RESIN STIRPS FOR ELEMENTAL ANALYSIS OF ESTUARINE WATER AND COASTAL ORGANIC SOILS
3.1 Summary and Introduction
The potential of using resin strips for analysis of wetland soils, especially
in coastal wetlands, needs to be investigated because of the high soluble salt
concentrations present within coastal organic soils. Salinity and biogeochemical
status influence sulfur levels within the coastal marshes. Inorganic sulfur
fraction may indicate the spatial variability of pedological processes within the
marsh. Sulfur fractionation for marsh soils involves complicated procedures
therefore, resin extractable 8 may be used when large number of samples
need to be analyzed.
A laboratory experiment was conducted to study the influence of salinity
and chloride on resin extractable S using anion-exchange resin strips. Anion
exchange (AE) and cation exchange (CE) resin strips of 10 X 40 mm, were
equilibrated with ionic solutions having different levels of SO 4 and 0 1
concentrations. Bicarbonate, chloride (Cl), and phosphate were tested for
terminal ions. All three anionic forms equally extracted sulfate. Salinity and Cl
significantly reduced the resin extractable sulfate. Ionic strength and competing
ions can limit the affinity of the target ions for the resin.
The potential of using AE and CE resin strips was tested for water
samples collected from brackish and saline marsh types within the Barataria
Bay Basin, Louisiana. Major cations and sulfate in water samples were well
predicted from resin extractions. Inclusion of Electrical Conductivity (EC) into
39
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
the regression equations improved R , especially for divalent ions. The 0.5M
HCI can preferably be used for elution of both resins. Salinity and the ionic
competition need to be considered when predicting elements for estuarine
w ater samples using resin strips.
The performance of different eluents, effects of equilibration time and
elution time, and soil/water ratio on resin extractable S were studied. An
equilibration time of 16 h was adequate. A soil/water ratio of 1/10 can be used,
but for high sulfur conditions, either lower ratios or more resin strips may be
used. Over 16 h elution levels off the resin extractable 8 , therefore, A 16-h
elution time period can be used.
Resin extractable 8 was compared with water soluble, pyritic and non-
pyritic 8 in coastal organic soils. Resin extractable 8 predicted water soluble 8
for organic soils and non-pyritic 8 for organic and mineral soils. Adding Cl and
pH of soil suspensions to the regression model improved the predictability.
Mineralization of sulfur may limit the predictability similarly in agricultural soils.
However, using more resin strips for equilibration may alleviate this limitation.
This procedure is proposed as an alternative to the traditional analytical
methods, especially for studying spatial variability within the coastal marshes.
Prediction models presented in this paper are recommended for the Barataria
Bay Basin water system and similar estuarine systems.
Marsh types within the Barataria Bay are affected by seawater intrusion.
The marsh is delineated as saline, brackish, intermediate, and freshwater
marshes depending on the salinity levels (Feijtel et al., 1988; 8 oil Conservation
40
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Service, 1989). Seawater provides salts to this environment. Sulfur plays an
important role in this environment. It contributes to salinity, is a major plant
nutrient, and is an electron acceptor for the reduced soil and undergoes sulfate
reduction. Excessive sulfate can cause adverse effects on plants (Carlson and
Forrest, 1982; Mayland and Robbins, 1994; Ewing et al., 1995). Plants adapt
through different mechanisms to tolerate high salt concentrations in their root
zone (Carlson and Forrest, 1982; Bradley and Morris, 1991). Composition of
pore water may be different resulting different ionic ratios, due to differences in
ion uptake by the plants (Bradley and Morris, 1991; Latham et al., 1994). Sulfur
uptake may be limited due to high concentration of Cl in saline marshes. Ionic
competition and Cl effects on affinity of S for roots can be studied using resin
strips.
Nutrient phytoavailability can be evaluated using ion-exchange resin
membranes and resin strips have given promising results for upland soils
(Searle, 1988; Schoenau and Huang, 1991; Qian et al., 1992; Searle, 1992;
Lee and Zheng, 1993; McLaughlin et al., 1993; Qian et al., 1994). Resin strips
need to be tested for marsh soils because use of resins will alleviate problems
of complicated soil sampling and preparation processes. Resins will enable a
direct comparison of nutrient status of soils with varying bulk density.
Hydrology within the Barataria Bay basin was monitored as part of the
Louisiana NASA/EPSCoR global change cluster project (Miller et al., 1995). It
was planned to identify indicator elements to monitor temporal changes in
water flow direction because water flow into or out of the marsh can be
41
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
determined from water composition data. This requires analysis of a large
number of samples. W ater samples within the project area are highly saline.
Salinity ranges from 5 to above 20 ppt within intermediate, brackish, and saline
marshes of Barataria Bay Basin (Soil Conservation Service, 1989).
Inductively Coupled Plasma (ICR) and the Ion Chromatography (1C) are
mostly used for water analysis and require less sample preparation. Estuarine
waters are highly saline and have very high concentrations of soluble salts.
These excessive ionic concentrations interfere with the target ions when 1C and
ICR are used for elemental analysis. Sample dilution to avoid this problem can
dilute the target elements below the detection limits of the instruments. This
problem could be overcome if element concentrations in the water sample can
be predicted from the extractable elements from resin strips. Another
advantage is the possibility to concentrate the elements that are in trace
concentrations in the sample (Edwards et al., 1993).
Ion-exchange resin strips could also be used in soil testing since they
give a quick assessment of elemental concentrations within the soil (Lee and
Zeng, 1993; McLaughlin et al., 1993). Ionic competition due to high salinity in
coastal wetland soils may limit the affinity of target ions on resin (Amer et al.,
1955). This potential limitation must be identified before using them for these
soils. In this study, resin strips were tested for multi-elemental analysis of
estuarine water and coastal organic soils.
42
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
3.2 Literature Review
3.2.1 Multi-Elemental Analysis in Soil Using Ion-Exchange Resins
Ion exchange resins can extract plant available elements from soil (van
Raij et al., 1986). A mesh bag filled with resin beads was used for multi-
elemental soil extraction (Sibbesen, 1977; Somasiri and Edwards, 1992).
Skogley et al. (1990) proposed a phytoavailability soil test. It is a simplified soil-
extraction methodology based on ion-exchange resin extraction of nutrients
from saturated pastes of soil samples. Somasiri and Edwards (1992)
suggested a multi-elemental analytical technique using a mixed resin system
with ICP for element detection. Use of resins eliminates soil sample
preparations procedures (Sibbesen, 1977; Skogley et al., 1990) and overcomes
several changes caused to the soil samples during conventional soil analysis
(Searle, 1988, 1992). Soil phosphate was tested using anion exchange resins
in the form of beads ( Amer et al., 1955; Vaidyanathan and Talibudeen, 1970;
Barrow and Shaw, 1977) and strips (Schoenau and Huang, 1991).
Resin membrane strips have replaced the use of beads (Qian et al.,
1992) and have overcome problems affiliated with beads, especially cleaning
and separation from the soil (Schoenau and Huang, 1991; Somasiri and
Edwards, 1992). These membranes are available in the form of AE and CE
membranes. The AE strips have been used to estimate plant available
phosphate (Schoenau and Huang, 1991), sulfate (Searle, 1988, 1992), and
nitrate (Qian et al., 1994). Phytoavailable Ca, K, Mg, and Cd have been
satisfactorily estimated using CE strips (Qian et al., 1992; Lee and Zheng,
43
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
1993; McLaughlin et al., 1993). Resin strips were used in trace metal analysis
(Jing and Logan, 1991, 1992; Liang e ta l., 1994; Tejowulan et al., 1994) and
elemental toxicity assessment in saline soils (Greer and Schoenau, 1994).
Szmigielska and Schoenau (1994) used resin strips to estimate 2,4-D amine
retention in soil. The exchangeable nutrient levels estimated with resin strips
correlated well with commonly-used analytical extractions (McLaughlin et al.,
1993) and with plant uptake (Schoenau and Huang, 1991) and were
reproducible for a wide range of soils (Qian e ta l., 1992; Searle, 1992). The
tested plant uptake correlations included P uptake by cotton and flooded rice
(Van Raij et al., 1986);N and S uptake by canola and wheat (Qian et al., 1992).
Sulfate extracted from soil using strips of phosphated AE strips were well
correlated with sulfate extracted by monocalciumphosphate (MCP),
(Ca(H2P04)2), therefore, one can avoid several problems associated with the
MCP extraction method (Searle, 1992). Cation and anion exchange
membranes can be used in multi-elemental analysis (Qian et al., 1992;
McLaughlin et al., 1993). Recent studies have shown that field burial of
membrane strips successfully estimated available nutrients in arable soils
(Schoenau et al., 1994).
Resin strips are simple to use and have been used in simulating cation
or anion sinks (Robinson and Syers, 1990), soil testing (Qian et al., 1992),
mineralization studies (Searle, 1992; Parfittet al., 1994), and soil fertility
assessment (McLaughlin et al., 1993).
44
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
3.2.2 Effect of Soluble Salts on Membrane Extractable Elements
Soluble salts provide competing anions that may decrease the
concentration gradient of phosphate across the solution film surrounding the
resin (Amer, 1955). A concentration of 20 ppm NaCI reduced the resin's P
adsorption by 1%, but this effect was minor for arable soils (Amer at al., 1955).
However, consideration should be given to the soluble salt effects in resin
performance using coastal marsh soils. Resin extractions under saline field
conditions may represent the phytoavailability for field conditions. Absorption of
P was significantly reduced by low pH (pH 4.0 vs. 5.5) due to reduced diffusion
coefficient of P. Adsorption of P by the resin is independent from resin to soil
ratio and the rate and method of continuous shaking (Amer et al., 1955). Ionic
strength and charge balancing for divalent cations improved P adsorption from
soil (Curtin et al., 1987). Charge balancing may not be important in sulfate
adsorption, but ion competition may influence sulfate adsorption from soil.
3.2.3 Estimation of Membrane Exchangeable S
Sulfate can be estimated using AE strips (Searle, 1988, 1991; Qian et al,
1992). An AE strips (BDH cat. no. 55164) of 40 mm X 4 mm, absorbed
approximately 16,000 |ag g"' S from 0.5 M KgSO^ solution (pH 5.8). The
presence of high concentrations of phosphate did not interfere with sulfate
absorption. This indicates the high affinity of the phosphated-membrane for the
sulfate ion (Searle, 1988). Yang et al. (1990) and McLaughlin et ai. (1993)
indicated that mineralization of sulfur could limit sulfate measurements due to
45
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
high variability. Searle (1988) estimated resin exchangeable sulfate in New
Zealand soils where carbon content ranged from 2.2 to 39.0 %, including a
Histosol. Mineralizable 8 estimates had a higher degree of variation than
membrane extractable sulfate (Searle, 1992). Reported sulfate estimates with
membrane strips covered a wide range; 2 to 108 pg g' in New Zealand soils
(Searle, 1988, 1992) and 2 .2 to 1195 pg g"" in western Canadian soils (Qian et
al., 1992). These estimates indicate that the exchange capacity of AE strips is
well above the sulfate levels for arable soils however, its capacity for coastal
marsh soils must be tested.
3.2.4 Methodology Adopted in Resin Extraction of S
Searle (1988, 1992) used phosphated AE strips while Qian et al. (1992)
used bicarbonated AE strips to estimate phytoavailable S following a similar
procedure. Resin strips are first converted into an ionic form suitable for
exchanging the target ion by shaking in an ionic solution. Next, the membrane
is shaken in a soiliwater suspension overnight to equilibrate. It is rinsed with
deionized water and shaken in eluent solution to extract the target ion from the
membrane. The eluent solution is analyzed for the target element. Sulfate in
the eluent can be analyzed turbidimetrically as barium sulfate (Searle, 1988,
1992), manually using a spectrophotometer (Searle, 1991), or using ICP (Qian
et al., 1992). The membrane can be regenerated for reuse.
There are limited reports that indicate the use of resin membranes for
estuarine water and sediment analysis. Edwards et al. (1993) proposed the
46
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
ability of using resin strips for monitoring river water composition. Resin strips
can be placed in water for a time period and then exchanged ions can be
estimated. Relationship between resin extractable elements and sample
concentrations need to be established to use this method. Soluble salts
provide competing anions that may decrease the affinity of the target ion to the
resin strip (Amer, 1955).
The primary objective was to study the effect of salinity and chloride
concentration on resin-extractable 8 to indicate possible 8 accumulation within
the root zone. The secondary objective was to study the feasibility of using ion-
exchange resin strips for elemental analysis for estuarine water and 8
estimation for coastal organic soils.
3.3 Materials and Methods
Anion- and cation-exchange resin membranes (BDH cat. no. 55164-2
and 55165-2, respectively) were used. Resin membranes were cut into 10 X
40 mm strips. The AE strips were kept in 0.5 M NaNCO j (pH = 8.5) for 48 h to
convert into bicarbonate form while CE strips were converted into H form by
keeping them in 0.5M HCI for 48 h. Resin strips were rinsed thoroughly and
stored in deionized (Dl) water to avoid drying.
The general procedure for resin extraction is presented in Figure 3.1.
Resin strips are shaken in soil:water suspensions or water samples overnight
(16 h) for ion exchange. The strips are rinsed with Dl water and transferred into
the eluent (25 to 50 mL of 0.5M HCI). The elements exchanged on to the resin
are eluted after shaking in the eluent for 24 h. The eluent solution is analyzed
47
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD■ D
OQ.C
gQ.
■DCD
C/)C/)
8■D
CD
3.3 "CD
CD■DOQ.C
aO3"OO
CDQ.
■DCD
C /)C /)
Resin Strips
H C 03-water sample (50 mL)
or soil suspension
40 m m X 10 mm
(Regeneration)> <
00
— \ (Shake 24 h)
(Rinsed with Dl water)
(Analysis by ICP)
50 m l of eluent 5 M HCI)
(Shake 24 h)
Figure 3.1. Schematic presentation of the general procedure for resin extraction.
for the target element using Inductively Coupled Plasma (ICP-AES). Resin
extractable elements can be expressed in concentration units or based on unit
resin area or unit soil weight, for data analysis. The resin strips are regenerated
for reuse.
3.3.1 Salinity and Chloride Effect
The AE strips were used in three ionic forms, bicarbonate, chloride, and
phosphate separately. Five sulfate levels, 300, 600, 1500, 2400, and 3600 mg
were obtained using KgSO^. Salinity levels were adjusted to approximately
5 ,1 0 , 15, 20, 25, and 30 dS m' by adding KOI to each sulfate level. Each
sulfate level had its lowest salinity level without chloride. Different salinity levels
were obtained based on the relationships reported by the U. 8 . Salinity
Laboratory Staff (Bresler et al., 1982) as given in equation 3.1. Salinity is
expressed as total dissolved solids (TDS).
TDS (mg L'^) = 0.64 * 10^ EC (dS m'"') [3.1]
The general procedure was followed for resin extraction with 24 h equilibration
and 24 h elution times.
3.3.2 Multi-Elemental Analysis of Estuarine Water
W ater samples were collected from different water bodies within the
brackish and saline marsh types of the Barataria Bay Basin, Louisiana. W ater
samples used for the experiment were brought to the laboratory in containers
placed in an ice-filled cooler. W ater samples were filtered with Whatman No.
42 filter paper. The EC of the water samples was measured using the
49
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
conductivity sensor of a M 90 pH, conductivity and dissolved oxygen meter
(Corning Inc., Corning New York 14831, USA). Water samples were analyzed
using ICP-AES (PERKIN ELMER model OPTIMA 3000 (Perkin-Elmer
Corporation, Norwalk, CT 06859, USA) and pH was measured with a pH meter
(Orion Research model 701A/digital lONALYZER).
Twenty-seven water samples having a wide range of ECs were used for
this experiment. A 50-mL water sample was used for resin extraction following
the general procedure (Figure 3.1) with 24 h for shaking and elution times, in
four replicates. The AE and CE strips were eluted separately. The CE strips
were eluted with 25 mL of 0.5M HCI. Two replicates of AE strips were eluted
with 25 mL of 0.5M HCI while the other two were eluted with 25 mL of 0.5M
NaHCOg to compare the performance of the two eluents, HCI and NaHCO j for
AE strips. The NaHCO^ eluent can interfere with low sulfur detection by the
ICP-AES.
3.3.3 Resin-Extractable 3 Analysis for Coastal Organic Soils
Three preliminary experiments were conducted to study the effects of
equilibration time, elution time and soil/water ratios on resin extractable S for
organic coastal soils.
3.3.3.1 Equilibration and Elution Time Experiment
Time periods, 1, 3, 6 , 10 ,16 , and 24 h were tested to determine the
effect of equilibration time on resin extractable S. Soil collected from a saline
marsh surface organic layer was used for the study. Soil/water ratio of 1 ; 10
was used mixing a 5-mL scoop of soil with 50 mL of Dl water in triplicate.
50
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
General procedure (Figure 3.1) was followed for resin extractions changing the
shaking time for different samples. In separate sets of three replicates, elution
times of 2, 3, 6 , 10, 16, and 24 h were tested using the same 1/10 soil/water
ratio.
3.3.3.2 Soil/Water Ratio Experiment
Surface organic soil at different ratios of soil/water, 1/5, 1/10, 1/20, and
1/40 were used for resin extractions. Shaking time and elution time was 24 h.
The A E strips were eluted separately with 0.5M HCI.
3.3.3 3 Resin-Extractable and Water Soluble S Analysis
Soil samples were collected from the organic subhorizones and the
mineral horizon of saline and brackish marsh soil profiles of Barataria Bay,
Louisiana. Soil suspensions obtained by mixing 5 mL of soil and 50 mL of Dl
water (1/10, soil/water) were shaken for 24 h following the general procedure
(Figure 3.1) with three replicates for each sample. The AE strips were shaken
for 24 h and the eluted for 24 h in 50 mL of 0.5M HCI. Similar soil/water
suspensions were shaken for 24 h without resins to estimate water soluble S,
EC, chloride concentration and pH of the soil suspension. The EC of the soil
suspensions was measured with the conductivity sensor of M90 pH,
conductivity meter (Corning Inc., Corning New York 14831, USA). The filtrate
was analyzed using ICP-AES (PERKIN ELMER model OPTIMA 3000 (Perkin-
Elmer Corporation, Norwalk, CT 06859, USA), and pH was measured with a pH
meter. Cl was measured using a Cl specific electrode with a pH/mV meter
51
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
(Orion Research model 701A/digital lONALYZER). Resin extractions were
compared with water soluble S, non-pyritic S and pyritic S for organic soils.
3.3.3.4 Pyritic and Non-Pyritic S Analysis
A method used for pyrite estimation in coal and ceramics was modified
for the analysis of extractions for Fe and S by the ICP-AES. Pyritic 8 was
estimated indirectly from the pyrite content (Schneider and Schneider, 1990).
One scoop (1/8 tsp.) of soil was measured into a digestion tube. Six tubes that
were calibrated to 50 or 75-mL volume, were used for one soil sample. Tubes
were separated into two batches. One was for non-pyritic (NP) and the other
set was for pyritic (P) and non-pyritic (NP) Fe digestion. The 50-mL tubes
were used for non-pyritic Fe, while the 75-mL tubes were used for pyritic and
non-pyritic Fe. A sample was placed at the bottom of the tube. Six mL of
concentrated HCI were added into each tube with soil, under a fume hood and
the tube was covered with a small glass ("reflex") funnel. The soil was stirred
within the acid to make a suspension and left over night, covered with "reflex"
funnels. The next morning, 23 mL of Dl water was added to each tube. The
digestion procedure was different for "NP" and “NP+P" sets, therefore they
were digested separately. To digest the NP set, the sample was placed onto
the digestion block, and the block heater was turned on. It took about 15 to 20
min for the mixture to start boiling. The samples were kept boiling for one hour
and were removed and allowed to cool. The tubes were filled to the 50 mL
level with 1:10 HCI then mixed well and filtered through #5 (or #42) Whatman
52
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
filter paper. The filtrate was highly acidic; therefore, it was diluted six times to
reduce the acidity and to increase the detection levels by the ICP.
For the “NP+P” set, after adding 23 mL of water, the sample was boiled
for 30 min and then 25 mL of 3N HNO 3 was added to each tube while they were
on the digestion block. The acid was slowly added through the funnel. It took
another 10 to 15 min for the mixture to start boiling. Samples were boiled for
another 30 min and cooled. The tubes were filled to the 75-mL level with 2N
HNO 3 then mixed well and filtered through #5 (or #42) Whatman filter paper.
The filtrate was highly acidic; therefore, it was diluted six times before analysis
by the ICP. The pyritic Fe content was determined based on the difference
between Fe content of “NP+P” and “NP” digestions. The pyritic Fe content was
estimated using equation 3.2.
Pyritic Fe (rng L ') * 1.1487 = Pyritic 8 (mg L ') [3.2]
The S content from the “NP” digestion was the non-pyritic 8 content (Schneider
and Schneider, 1990).
3.3.4 Data Analysis
Regression analysis was performed for the data using the general linear
model procedure (PROC GLM) in Statistical Analysis System (SAS Institute
Inc., 1989) to identify the relationships between the amount of resin-extracted
elements and the elements in water. Single and multiple linear regression
models were fitted for different elements. The EC of water sample was included
as an additional variable. Mean comparison was obtained using the PROC
GLM procedure for different eluents. Regression analysis and analysis of
53
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
variance (ANOVA) were performed to identify the effects of equilibration time,
elution time, soil/water ratios on resin extractable S. Correlation and regression
analyses were conducted to study the relationship between resin extractable S,
water soluble S and pyritic and non-pyritic S.
3.4 Results and Discussion
3.4.1 Salinity and Chloride Effect
Resin extracted sulfate content was expressed as mg SO 4 cm'^.
Maximum sulfate extracted on the resin strip was 0.59 mg SO 4 cm that is
equivalent to 8287 pg SO 4 g ^soil. Figure 3.2 presents the effect of salinity and
sulfate levels on resin extractable sulfate. Salinity reduced the amount up to
0.007 mg SO 4 cm'^, which is a drop from 100% to 5 %. Statistical analysis
indicated that salinity significantly reduced (p=.0 0 1 ) resin extractable sulfate
content at each sulfate level. Both salinity and chloride concentrations were
highly correlated with resin extractable sulfate. Figure 3.3 presents the
competition by Cl ions with sulfate on resin exchange. The maximum resin
extractable sulfate is limited by the resin’s exchange capacity. The competing
individual ions and the total soluble ionic concentrations affect the affinity of the
target ions to the resin. The interactive effect of 01 and sulfate on resin
extractable sulfate is presented in Figure 3.4. A linear relationship is noted for
both Cl and sulfate levels on resin extractable sulfate.
54
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD■ D
OQ.C
8Q.
■DCD
C/)C/)
8■D
CD
3.3 "CD
CD"OOQ.CQ
■DO
CDQ.
■DCD
enen
0.60
-0-3O O ppm
-B -6 0 0 p p m
-z^ 1500p p m
-* -2 4 0 0 p p m
—h"SBOOppm
0.50
I- 0.40co^ c f "
■G o 0.30 2
SC
I 0.20
0.10
0.0010 200 5 15 25 30
-1 ,Electrical Conductivity (dSm )
Figure 3.2. Effect of salinity and sulfate level on resin extractable sulfate.C /)C /)
CD■ D
OQ .C
gQ .
■DCD
C/)C/)
CD
8■D( O '
3.3"CD
CD■DOQ .C
ao3T3O
(DQ .
Ü1O)
0.50
E 0.40 u
ê0)g 0.303
W0)SI
50.20
SI 0.10CH
0.001000 2000 3000 40000 5000 6000 7000
T3(D
Chloride (mgL’ )Figure 3.3 Effect of chloride concentration on resin extractable sulfate at 600 mg S L-1
(/)(/)
O'
' I AQq.
I.:I
Figure — "
3.4.2 Multi-Elemental Analysis of Estuarine Water
Elemental concentrations, EC, and pH ranges of water samples used in
the experiment are presented in Table 3.1. Descriptive statistics for different
elements, EC and pH were obtained by SAS PROC UNIVARIATE procedure
(SAS Institute Inc., 1989). The EC, pH and major elements were normally
distributed. Sodium, Mg, Ca, and K were the major cations and chloride and
sulfate were the major anions in the water samples. Major cations maintained
the same proportions within the EC range used for the study. For example, out
of the major cations on weight basis, Na was dominant and was 83.5% (SD ±
0.7), with much less proportions of Mg 10 (±0.1)% , Ca 3.6 (±0.5)% , and K 3.0
(±0.1)% . Major cations and sulfur concentrations were highly related to the
electrical conductivity of the water samples; this indicates seawater is the main
source of the elements. Figure 3.5 presents the relationship between electrical
conductivity and concentration for sulfur and potassium. Element
concentrations were linearly related to EC; linear regression accounted for 96%
of the variation for S and 97% of the variation for K. Similar relationship was
observed for the other elements.
Statistical analysis indicated that the use of both resins together did not
make a significant difference in resin extracted elements; this was true for both
anions and cations. Means of different eluents used for anionic resins were
not significantly different. This suggests that 0.5M HCI can be used as the
eluent for anionic resins. This avoids the variability due to dilution of NaHCOg
58
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD■ D
OQ.C
gQ.
■DCD
C/)Wo"303CD
8■D( O '3"
13CD
"nc3.3 "CD
CD Ü 1■D COOQ.C
aO3
■DO
CDQ.
■DCD
(/)(/)
Table 3.1. Electrical conductivity, pH and elemental concentration ranges of water samples used in the experiment.
Descriptive
Statistics
EC pH
Element concentration^
Ba Ca Cu K Mg Na S Sr Zn
Mean 25.04 7.91 0.173 162.72 0.043 139.87 473.22 3996 327.41 2.816 0.097
SD^ 12.97 0.19 0.051 73.49 0.041 70.58 236.98 2038 167.19 1.338 0.078
Minimum 5.37 7.54 0.074 46.93 0.003 31.36 99.24 797 73.14 0.691 0 . 0 0 2
Median 22.80 7.92 0.181 148.15 0.029 124.96 436.03 3623 301.98 2.610 0.072
Maximum 52.70 8.29 0.330 293.51 0.171 267.53 878.18 7423 636.33 5.098 0 . 2 2 1
27 samples: Standard Deviation
CD■ D
OQ.C
gQ.
■DCD
C/)C/)
CD
8■D( O '
3.3"CD
CD■DOQ.Cao3
T3O
CDQ.
O)o
800
A Potassium (K)
Y = 12.66X+ 10.52 [r2 = 0.96]O Sulfur (8 )600 -
O)Eco
5 400 -
§8
E 200 - 0}
111Y = 5.35X + 5.87
[r2 = 0.97]
5 10 150 20 25 30 35 40 45 50
T3CD
(/)(/)
Electrical conductivity (dS m' )
Figure 3.5. Potassium and sulfur concentration as influenced by electrical conductivity in water samples.
eluent for ICP analysis. Therefore, only the data from HCI eluent were used for
regression analysis of resin extracted sulfate.
Resin extracted elements exhibited curvilinear relationships with
elements in water samples, as well as with the EC. Resin extracted-K
increased linearly (r = 0.87) with the increasing amounts of K in water (Figure
3.6) but decreased exponentially (r = 0.94) with increasing EC (Figure 3.7).
Total major cations extracted by the resin at all EC levels were similar
and were about 0.1 meq. However, the percentage of different cations
exchanged on to the resin changed with EC. More Ca and Mg were exchanged
at lower EC levels than Na and K. When the EC increases, monovalents (Na
and K) dominated the system and exchange to the resin was greater. Figure
3.8 shows the resin-extracted proportions of major cations in milliequivalents.
However, the milliequivalent percentages in water were similar at all EC levels;
Na 78% , Mg 17%, Ca 3.5% and K 1.5%. Skogley et al. (1990) proposed a
phytoavailability soil test because resins are known to mimic plant roots. Based
on this information it seems at high salinity, plants may absorb excess Na but at
lower salinity Mg and Ca are in excess. Affinity of sulfate also was dramatically
reduced with the increase in salinity (Figure 3.9). Chloride can be the major
competitor with sulfate, similar to cations at high salinity monovalents dominate
the system.
The following abbreviations are used: amount of element in the water
sample (W(g)) and the quantity eluted by the anionic resin strips (ARE^g,) and
61
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD■ D
OQ.C
gQ.
■DCD
C/)
o'3O
8
ci'
33 "CD
CD■DOQ.C
aO3
■DO
CDQ.
■DCD
C /)C /)
S
0.10
Y = 0.0039X + 0.0334
[r = 0.87]0.08 -
O)
& 0.06 - bdXJd)o2
0.02 -
0.000.00 2.00 4.00 6.00 8.00 10.00
K in water (mg)
Figure 3.6. Resin extracted K at different K levels in water.
12.00 14.00
CD■ D
OQ .C
gQ .
■DCD
C/)C/)
8■D
3CD
3.3 "CD
CD■DOQ .C
aO3
■DO
CDQ .
■DCD
C /)C /)
G )W
0.025
Y = 0.0565 X-0.574
[r = 0.94]0.020
O)E^ 0.015 - •o 0)c32
Iç 0.010 - tnK
0.005 -
0.00010 20 300 40 50
Electrical Conductivity (dS m’ )Figure 3.7. Relationship between electrical conductivity and resinextracted-K.
m O) mZ Üo □ < O
in
o
o0 0
oCN
o
ooCN
oo
en
.>o=3
X Jcoo
s(U
LU
go
!■§'E
mO )
IS0)Q .
I53O"0)
T3
E
C
'%0 :0000
E3O)
(baui p %) p e u i8 | 3 papejpcg ujsay
64
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD■ D
OQ .C
gQ .
■DCD
C/)
o"3O
8■D
3.3 "CD
CD■DOQ .C
aO3
■DO
CDQ .
■DCD
C /)C /)
O)Ol
0.02
Y = 0.082 X-1.0821
[r = 0.99]0.01 -
cr0)Ed)
3w
0.00 -
0.005 10 15 20 25 30 350 4540 50
-1 ,Electrical conductivity (dS m )Figure 3.9. Sulfate milliequivalents exchanged onto the resin at different EC levels of
water samples
the cationic resin strips (CRE^g)), where e stands for element. Linear and
quadratic regression models were fitted between resin extracted-elements RE^g,
and W(e). The EC was included as a second variable with first, second and third
powers of RE^g,. The best regression models and the statistics for each
element are presented in Table 3.2. Addition of the electrical conductivity of
the water sample (EC) as a second variable improved the R values. Major
cations did not achieve much improvement, but in some cases, addition of EC
accounted for 30 to 70% of additional variability compared to that of ARE^g, or
CRE(g, alone. A linear regression of CREj^g) alone accounted for 91 % of the
variation in W,Na). For Na and K, quadratic relationships barely improved
predictions. Adding EC increased R^ by another 6 % for Wj^a) and 10% for W^^).
Adding EC increased the R for other models considerably. Addition of EC
increased the R by 35% (R^ 0.62 vs. 0.97) for and explained 96% of the
variation in W(ca>- Much larger improvement was observed for Sr when EC was
included in the model (R^; 0.22 vs. 0.96). This points out the importance of
including EC to predict minor elements in the system. The best models only
accounted for about 30 % of the variation in \N^zn) and 25 % of the variation in
W(Ba)- This may be due to the presence of very low concentrations of these
elements. However, prediction of V^cu) was better (R = 0.66) than V^^n) and
W(Ba) and this may be due to the better detection of Cu by ICP-AES. Anionic
66
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD■ D
OO.C
gQ .
■DCD
C/)
o"3O
8■D
( O '3"
i3CD
"nc3.3 "CD
CD■DOQ .C
aO3
■DO
CDQ .
O)
Table 3.2. Regression model for different elements to predict elements in the water using resin extracted elements.
Element Regression Model'*’ R p-value
Ca W(ca) = 1.9284 -1.4331 * CRE(ca) + 0.2676 * EC 0.96 0 . 0 0 0 1
Mg W(Mg) = 4.5162 - 5.0493 * CRE(Wg) + 0.8676 * EC 0.96 0 . 0 0 0 1
Na W(Na) = -26.04 + 91.994 * CRE(Na) + 6.0834 * EC 0.97 0 . 0 0 0 1
K W(K) = -0.7685 + 32.2 * CRE(K) + 0.2321 * EC 0.97 0 . 0 0 0 1
Sr W(sr) = 15.658 - 0.0733 * CRE(Sr) +5.0208 * EC 0.96 0 . 0 0 0 1
SO4 W(so4) = 7.4964 -12.8661 * ARE(so4) + 1 7463 * EC 0.96 0 . 0 0 0 1
Zn W(zn) = -6.9058 + 40.3568 * CRE(zn) - 26.3448 * [CRE<zn)] 0 . 2 2 0 . 0 0 0 1
Ba W(Ba) = 4.49 + 8.82 * CRE(Ba) - 3.91 * [CRE<Ba)f + 0.46 * [CRE(Ba)f 0.29 0 . 0 0 0 1
Cu W(cu) = 2.25 - 5.0523 * CRE(Cu) + 5.4185 * [CRE(Cu)]^ 0 . 6 6 0 . 0 0 0 1
W(e) = element in water; CRE(e) = cationic resin extracted amount;
m ARE(e) = anionic resin extracted amount; weights in mg for Na, Mg, Ca, K and SO4 , g for others)
U)'w EC = Electrical Conductivity of water sample (dS/m)
resin extracted-sulfate explained 65% of the variation in W(so4), and addition of
EC into the model increased the to 0.96. The models are indicative of the
affinity of individual ions for the resin. Improved with additional variable of
EC indicates to what extent their affinity is influenced by ionic competition.
Factors contributing to ionic activity such as ionic strength, and ion pairing may
be responsibly controlling the affinity of individual ions onto the resin. These
models emphasize the role of EC in predicting elements using resin extractions.
Other elements that were not present in adequate amounts in this study need
to be calibrated separately and may be predicted with resin extraction. The
water system in Barataria Bay Basin is dominated by Cl and Na* ions. High Cl
concentration interferes with the detection by Ion Chromatograph (1C) because
it’s peak spreads over the range of other target anions, such as SO 4 , PO 4 and
NO 3 . High Na in the matrix interferes with the target ions during ICP analysis.
This will give proper estimates as well as protect the instrument from damage
due to high salt concentrations. As indicated by the models presented in Table
3.2, the use of resins can be a suitable alternative for estuarine water analysis.
Mean comparison indicated no significant difference between eluents;
therefore, 0.5M HCI can preferably be used for elution of anionic resins. Major
cations and sulfate were well predicted by resin extractions. Inclusion of EC
into the regression equations improved the R . Addition of EC as a second
variable increased the R considerably for the divalent ions Mg, Ca and Sr. The
regression models emphasize the role of EC in predicting elements using resin
extractions in high saline conditions.
68
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
3.4.3 Resin Extractable S in Coastal Organic Soils
In the following experiments sub samples taken from a bulk soil sample
collected from the saline marsh type surface organic layer were used for
different treatments. Therefore, micro-site variation can be expected within the
soil sample used for the following experiments.
3.4.3.1 Equilibration and Elution Time
Effect of equilibration time on resin extractable S (RES) is presented in
Figure 3.10. The RES increased linearly within the equilibration times tested.
The overall effect of equilibration time on RES was significant (p=.001). The
equilibration periods less than 16 h, were significantly different from 16 h. The
24 h period extracted significantly higher RES than the 16 h equilibration.
However, considering the possible limitation of resin’s capacity, a 16 h
(overnight) equilibration time is recommended for coastal organic soils.
The overall elution time effect was significant on RES (p=.032). This
may be due to the micro-site variation within the soil sample used for the test
because no relationship was observed within the different elution times tested
and RES (Figure 3.11). However, it shows that the RES levels off after 16 h.
Therefore, 16 h can be a suitable time period as elution time.
3.4.3.2 Soil/Water Ratio
Soil/water ratio significantly influenced the amount of RES (p=.002). The
RES at different soil/water ratios is presented in Figure 3.12. Soil/water ratio of
0.2 (1 :5) was significantly lower than other ratios. Dilution of the soil
69
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
GGDoinCOooo
(O I
in
OOD
OOO
CO
CM
0)Ei -O)cm
CO
ooCM
oin oo oin
( 1 6 lu ) s a iq e p B jp c g u is e y
70
JO’5too'cmg0E
CO
JO§
1Ç
mc o 0)
CO ™
co
*5cr0 )
Ü
Ê
CO23O)
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD■ D
OQ .C
gQ .
■DCD
C/)C/)
8■D
CD
3.3 "CD
CD■DOQ .C
aO3"OO
CDQ .
■DCD
C /)C /)
300
250
|) 200
cooro 150t j2Sç 1 0 0
I
8 12 164 20 240
Elution Time (h)
Figure 3.11. Effect of elution time on resin extractable S.
om
oCMO O
oin
oo
oino
OOO
oo-* o o ooooin
omoooo
(0cr
I
</>Ç)
I2Co01
Ig 8
ü
iCNi
co2=3O)
co CNJ CNJ ^ ^
H 6 lu) s aiqepBjpcg uisay
72
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
suspensions decreased the EC and that increased RES due to low ionic
competition. At a ratio of 0.025 (1 ;40) the RES was more than two folds
compared to 0.2 ratio. Further dilution may limit the resin strip’s exchange
capacity for the RES. For saline marsh soils, the ratio of 0.1 may be suitable,
but at lower salinity levels, it may be advisable to use lower ratios.
3 4.3.3 Resin Extractable S
There were 112 soil samples used for the analysis, 92 of them were from
organic subhorizons (Oa horizon), and 20 samples were from mineral horizon
(Cg horizon). Resin extractable S (RES), water soluble S (WSS), pyritic S
(PYS), and non-pyritic S (NFS) were measured in triplicate for each sample.
The EC of the 1:10 soil/water suspensions ranged between 0.07 to 1.37 dS m'
which is approximately equivalent to field salinity ranging from 0.77 to 15.07 dS
m '\ The 1:10, soihwater suspensions diluted the salinity effect that limits the
affinity of target ions on to the resin. This may create problems with resins
capacity for exchangeable ions.
Some variables followed a distinct bimodel distribution, therefore, it was
decided to separate data for organic and mineral soil layers for regression
analysis. Figure 3.13 presents the ranges of different S fractions of organic and
mineral soils. The S content is expressed based on soil volume as mg S L' of
soil. The following ranges were observed: RES 69 to 790 mg S L' for the
organic horizons, 64 to 1038 for the mineral horizons, W SS between 142 and
4307 mg S L' for the organic horizons and 813 and 5015 mg S L' for the
73
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD■ D
OQ .C
gQ .
■DCD
C/)C/)
8■D
CD
3.3 "CD
CD■DOQ .C
aO3"OO
CDQ .
S (mg r )
5000
4000
3000
2000
1000
ORES OW SS OPYS GNPS
MRES M W SS MPYS MNPS
S Fraction and Soil Horizon 0 = organic, M= minerai horizon
■DCD Figure 3.13. Boxplots showing data for different S fractions for organic and minerai horizons.
C /)C /)
mineral horizons, PYS between 81 and 5731 mg 8 L' for the organic horizons,
and 121 and 3853 mg 8 L‘ for the mineral horizons, NP 8 between 276 and
1307 mg 8 L' for the organic horizons, and 245 and 969 mg 8 L' for the
mineral horizons. The W 8 8 indicate high variation compared to R E 8 and NP 8 ,
this may be due to 8 mineralization during the measuring procedure. Chloride
concentrations ranged from 5.6 to 865 mg L' in soil/water suspensions, which
is equivalent to 61.6 to 9515 mg L' in the field. The pH ranges differed
between organic and mineral horizons, it ranged from 3.99 to 7.45 for the
organic horizon while for the mineral horizon ranged from 5.67 to 8.51.
Figure 3.14 presents the relationship between RE 8 and W 8 8 for the
organic horizons. The RE 8 increased with increasing W 8 8 . Figure 3.15
presents the relationship between RE 8 and NP8 for the organic horizons.
Figure 3.16 presents the relationship between RE 8 and NP 8 for the mineral
horizons. 8 eparation of mineral and organic horizons improved the regression
coefficients for individual models compared to the models used for all the soil
samples (R^ < 0.5). Different models to predict NP 8 and W 8 8 are presented in
Table 3.3 for organic and mineral horizons. Better prediction can be achieved
using different models for different soil horizons. Introducing pH and 01
concentration of the soil suspensions improved R^ for the organic horizon
models compared to mineral horizons. The W 8 8 had high variation, therefore,
none of the models predicted W 8 8 well except the model with logarithmic
75
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD■ D
OQ .C
gQ .
■DCD
C/)C/)
CD
8■D( O '
3.3"CD
CD■DOQ .C
aO3"OO
CDQ .
•n JO)
4000
3000O )EW _0)
I 2000w
iO o1000 Oo
2000 100 300 400 500 600 700 800
■ DCD
(/)o"3
-1 vResin Extractable S (mg L )
Figure 3.14, Relationship between RES and WSS for organic horizons.
CD■ D
OQ .C
gQ .
■ DCD
C/)
o"3O
8■D
3.3 "CD
CD■DOQ .C
aO3
■DO
CDQ .
1 4 0 0
1200
1000o O
O )
& 8 0 0 wü
O oi , 6 0 0Q.c o Z
o O
4 0 0
200
3 0 0 5 0 0100 200 4 0 0 6 0 00 7 0 0 8 0 0
T3(D
(/)(/)
Resin Extractable S (mg L’ )
Figure 3.15. Relationship between RES and NFS for organic horizons.
CD■ D
OQ .C
gQ .
■DCD
C/)C/)
8
3.3 "CD
CD■DOQ .CaO3"OO
CDQ .
N00
O)Ewü
èz
1200
1000
800
600
400
200
0200 400 600 800 1000
T3(D
(/)(/)
Resin Extractable S (mg L' )
Figure 3.16. Relationship between RES and NFS for mineral horizons.
CD■ D
OQ.C
gQ.
■DCD
C/)Wo"303CD
8■D
( O '3"
13CD
"nc3.3 "CD
CD■DOQ.C
aO3
■DO
CDQ.
■DCD
Table 3.3. Regression models to predict different sulfur fractions'* from RES for organic and mineral soils layers.
CD
Soil Layer Regression Model RZ p-value
Organic WSS = 2 .1 6 9 5 + 0 .8 2 2 2 * Log (RES) + 0 .0 3 5 3 * Log (Cl) 0 .6 2 0 .0 0 0 1
Organic NFS = 3 3 0 + 1 .0 5 6 1 * (RES) 0 .4 8 0 .0 0 0 1
Organic Log (NFS) = 5 .9 2 3 1 + 0 .0 0 1 7 * (RES) 0 .5 5 0 .0 0 0 1
Organic NFS = 1 .0 1 7 5 * (RES) + 9 0 .7 9 4 4 * pH - 1 6 2 .8 3 0 .5 8 0 .0 0 0 1
Organic Log (NFS) = 5 .1 9 5 1 + 0 .0 0 1 5 5 * (RES) + 0 . 1 3 4 0 4 * pH 0 .6 5 0 .0 0 0 1
Organic Log (NFS) = 3 .0 9 6 1 + 0 .4 9 2 3 * Log (RES) + 0 .1 0 3 5 * pH 0 .6 5 0 .0 0 0 1
Organic Log (NFS) = 4 .2 0 4 4 + 0 .3 2 7 9 * Log (RES) + 0 .0 6 7 5 * Log (01) 0 .7 1 0 .0 0 0 1
Organic NFS = 4 .2 8 3 1 + 0 .3 0 2 3 * Log (RES) + 0 .1 0 6 1 8 * Log (01) 0 .71 0 .0 0 0 1
Mineral NFS = 2 7 9 .7 + 0 .6 5 6 5 * (RES) 0 .7 3 0 .0 0 0 1
Mineral Log (NFS) = 3 .9 6 3 3 + 0 .3 9 7 7 * Log (RES) 0 .7 3 0 .0 0 0 1
Mineral Log (NFS) = 4 .5 8 3 7 + 0 .4 6 4 1 * Log (RES) - 0 .1 3 5 4 * pH 0 .7 7 0 .0 0 0 1
* W SS = water soluble S; RES = resin extractable S; NFS = Non-pyritic S.
(/)(/)
conversion of RES and Cl. Sulfur mineralization is a limitation reported in other
studies, for resin use (Searle, 1988). Sulfur mineralization may be the main
cause of low for W SS. Coastal organic soils are rich in other reduced S
compounds, in addition to the organic sulfur fraction that can be mineralized
during shaking for W SS and RES measurements. However, the models are
able to predict over 70 % of the variation despite the variations in marsh types,
salinity, chloride, organic/mineral ratio and pH. Resin extractable S can be
suggested to estimate non-pyritic 8 and water soluble S for spatial variability
studies.
3.5 Conclusions
Resin strips can be used to analyze the cation and anion concentrations
in water accurately, overcoming the high salt concentrations in the saline water
samples. Salinity and the ionic competition need to be considered when
predicting elements for estuarine water samples using resin strips. The models
predicted elemental concentrations in water samples while demonstrating the
ionic competition effect on individual ions. Salinity significantly reduces the
resin extractable sulfate. Either Cl concentration or EC can be added to the
model to predict elements in water from resin extractable elements.
Bicarbonate, Cl or phosphate can be used as a terminal anion for the AE strips.
The procedure and prediction models can be recommended for the Barataria
Bay Basin water system and similar estuarine systems.
80
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Both AE and CE strips can be used together for one sample and 0.5 HCI
can be used as the eluent for both resins if the ICP-AES is used for elemental
analysis. This procedure can be proposed as an alternative to the traditional
analytical methods. Equilibration time, elution time and the soil/water ratio
needs to be adjusted depending on the resin strips’ capacity, 8 levels and
salinity of the samples.
The RES maintained a linear realtionship with W SS and N FS in both
mineral and organic soils. Separation of mineral soils and organic soils
improved the regression coefficients, for individual models compared to the
overall model. Therefore, better prediction can be achieved using different
models for different soil types. Including pH or Cl concentration and
transforming data helped to obtain better prediction models for N FS and W SS,
especially for organic soils. Sulfur mineralization is a limitation, reported in
other studies, for resin use for S estimates (Searle, 1988). Sulfur mineralization
may be the main cause of low for models predicting W SS. However, the
models predicted over 70 % of the variation in NFS and W SS, despite the
variations in marsh types, salinity. Cl, organic/mineral ratio and pH. Resin
extractable S can be used to estimate non-pyritic S and water soluble S for
spatial variability studies.
3.6 References
Amer, P., Bouldin, D. R., Black, C. A. and Duke, F. R. (1955). Characterization of soil phosphorus by anion exchange resin adsorption and F32- equilibration. Fiant Soil 6:391-408.
81
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Barrow, N. J., and T. C. Shaw. 1977. Factors affecting the amount ofphosphate extracted from soil by anion exchange resin. Geoderma 18:309-323.
Bradley, P. M., and J. T. Morris. 1991. Relative importance of ion exclusion, secretion and accumulation in Spartina alterniflora Loisel.. J. Expt. Bot. 42:1525-1532.
Bresler, E., B. L. McNeal, and D. L. Carter. 1982. Saline and sodic soils: principles-dynamics-modeling. Adv. Ser. Agric. Sci. 10:1-27.Spring- Verlag, New York, New York.
Carlson, Jr., P. R., and J. Forrest. 1982. Uptake of dissolved sulfide bySpartina alterniflora: Evidence from natural sulfur isotope abundance ratios. Science 216:633-635.
Curtin, D., J. K. Syers, and G. W. Smillie. 1987. The importance ofexchangeable cations and resin-sink characteristics in the release of soil phosphorus. J. Soil Sci., 38:711-716.
Edwards, T., B. Ferrier, and R. Harriman. 1993. Preliminary investigation on the use of ion-exchange resins for monitoring river water composition. The Science of the Total Environment 135:27-36.
Ewing, K, K. McKee, I. Mendelssohn, and M. Hester. 1995. A comparison of indicators of sublethal salinity stress in the salt marsh grass, Spartina patens (Ait.) Muhl. Aquatic Botany 52:59-74.
Greer, K. J., and J. J. Schoenau. 1994. Salinity and salt contaminationassessment using anion exchange resin membranes. Proceedings of Soils and Crops Workshop, 1994, Univ. of Saskatchewan, Saskatoon, Sask., Canada. p44-48.
Jing, J. and T. J. Logan. 1992. Effects of sewage sludge cadmiumconcentration on chemical extractability and plant uptake. J. Environ. Qual. 21:73-81.
Jing, J., and T. J. Logan. 1991. Chelating resin method for estimation ofsludge-cadmium bioavailability. Commun. Soil Sci. Plant Anal., 22:2029- 2035.
Latham, P. J., L. G. Pearlstine, and Wiley M. Kitchens. 1994. Speciesassociation changes across a gradient of freshwater, oligohaline, and mesohaline tidal marshes along the lower savannah river. Wetlands. 14(3):174-183.
82
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Lee, D., and Zeng, H. 1993. Chelating resin membrane method for estimation of soi! cadmium phytoavailability. Commun. Soil Sci. Plant Anal. 24:685- 700.
Liang, J., and J. J. Schoenau. 1994. Determination of heavy metalcontamination in the soil environment using ion exchange membranes. Proceedings of Soils and Crops Workshop,Univ. of Saskatchewan, Saskatoon, Sask., Canada. p268-273.
Mayiand, H. F., and C. W. Robbins. 1994. Sulfate uptake by salinity-tolerant plant species. Commun. Soil Sci. Plant Anal., 25 (13&14):2523-2541.
McLaughlin, M. J., P. A. Lancaster, P. W. G. Salin, N. C. Uren, and K. I.Peverill. 1993. Use of cation/anion exchange membranes for multielement testing of acidic soils. Plant and Soil 155/156:223-226.
Miller, R. L., M. Giardino, B. A. McKee, J. P. Cruise, G. Booth, R. Rovansek, D. Muirhead, W. Cibula, K. Holladay, R. E. Pelletier, W . Hudnall, C. Bergeron,J. loup, G. loup, and G. Love. 1995. Processes and fate of sediments and carbon in Barataria Bay, LA. Proceedings from the Third Thematic Conference on Remote Sensing for Marine and Coastal Environments. Seatle, Washington. Vol. l:233-244pp.
Parfitt, R. L., K. R. Tate, and R. 8 . McKercher. 1994. Measurement of phosphorus mineralization using an anion exchange membrane. Commun. Soil Sci. Plant Anal., 25:3209-3219.
Qian, P., J. J. Schoenau, L. E. Cowell, and L. Dennis. 1 9 9 4 . Assessing nutrient availability variations in landscapes. Proceedings of Soils and Crops Workshop, 1 9 9 4 , Univ. of Saskatchewan, Saskatoon, Sask., Canada. P 2 7 4 -2 7 9 .
Robinson, J. S., and J. K. Syers. 1990. A critical evaluation of the factorsinfluencing the dissolution of Gafsa phosphate rock. J. Soil Sci., 41: 597- 605.
SAS Institute Inc. 1989. SAS/STAT User's Guide, Version 6 , Fourth Edition, Volume 2, Cary, NC: SAS Institute Inc., 846 pp.
Schneider, J. W ., and K. Schneider. 1990. Indirect method for thedetermination of pyrite in clays and shales after selective extraction with acid solutions. Ceramic Bulletin 69(1):107-109.
83
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Schoenau J. J., and W . Z. Huang. 1991. Anion-exchange membrane, water, and sodium bicarbonate extractions as soi! tests for phosphorus. Commun. Soi! Sci. Plant Anal., 22:465-492.
Schoenau, J., P. Qian, W. Z. Huang. 1993. Assessing sulphur availability in soil using ion exchange membranes. Sulphur in Agriculture 17:13-17.
Searle, P. L. 1988. The determination of phosphate-extractable sulphate in soil with an anion-exchange membrane. Commun. Soil Sci. Plant Anal. 19:1477-1493.
Searle, P. L. 1992. The extraction of sulphate and mineralisable sulphur from soil with an anion exchange membrane. Commun. Soil Sci. Plant Anal. 23:2087-2095.
Searle. P. L. 1991. A simple manual method for the determination ofphosphate-extractable (ion-exchange membrane) sulphate in soils. Commun. Soil Sci. Plant Anal., 22:1347-1354.
Sibbesen, E. 1977. A simple ion-exchange resin procedure for extracting plant- available elements from soil. Plant Soil 46:665-669.
Skogley, E. O., S. J. Georgitis, J. E. Yang, and B. E. Schaff. 1990. Thephytoavailability soil test - PST. Commun. Soil Sci. Plant Anal., 21:1229- 1243.
Soil Conservation Service (SCS). 1989. East Central Barataria cooperative river basin study, Jefferson, Orleans, Plaquemines and St. Charles Parishes, Louisiana. Rev. May 1989. United States. Soil Conservation Service. National Cartographic Center (U.S.). Ft. Worth, TX : USDA-SCS- National Cartographic Center ; [Alexandria, La. State Conservationist, distributor].
Somasiri, L. L. W., and A. C. Edwards. 1992. An ion exchange resin methodfor nutrient extraction of agricultural advisory soil samples. Commun. Soil Sci. Plant Anal., 23:645-657.
Szmigielska, A. M., and J. Schoenau. 1 9 9 4 . Determination of 2 ,4 -D amine in soils using anion exchange membranes. Proceedings of Soils and Crops Workshop, 1 9 9 4 , Univ. of Saskatchewan, Saskatoon, Sask., Canada. P 2 3 4 -2 4 3 .
8 4
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Tejowulan, R. S., J. J. Schoenau, and J. R. Bettany. 1994. Use of exchange resins in soil and plant testing for micronutrient availability. Proceedings of Soils and Crops Workshop, 1994, Univ. of Saskatchewan, Saskatoon, Sask., Canada. p255-267.
Vaidyanathan, L. V., and O. Talibudeen. 1970. Rate processes in thedesorption of phosphate from soils by ion-exchange resins. J. Soil Soi., 21:173-183.
van Raij, B., J. A. Quaggio, and N. M. da Silva. 1986. Extraction ofphosphorus, potassium, calcium, and magnesium from soils by an ion- exchange resin procedure. Commun. Soil Sci. Plant Anal., 17:547-566.
Yang, J. E., E. O. Skogley, and B. E. Schaff. 1990. Microwave radiation and incubation effects on resin-extractable nutrients: 1. Nitrate, Ammonium, and Sulfur. Soil Sci. Am. J. 54:1639-1645.
85
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CHAPTER 4: INFLUENCE OF SALINITY AND LANDSCAPE POSITION ON ACCUMULATION OF PYRITE AND NON-PYRITIC Fe AND S WITHIN
COASTAL ORGANIC SOILS OF BARATARIA BAY BASIN, LOUISIANA
4.1 Summary and Introduction
Coastal marsh favors pyrite formation because of the highly reduced
environment and the availability of 8 , Fe, and organic 0 within the marsh.
Pyrite accumulation represents the balance between pyrite formation and
oxidation. Pyrite accumulation can be variable due to variations in redox
potential, and availability of reduced 8 , and Fe, and labile 0 within the soil.
Information on pyrite content and non-pyritic Fe and 8 indicates the
biogeochemical status under which a particular soil horizon was formed. This
study examines the influence of landscape position on pyrite accumulation for
different marsh types. 8 alinity, pyrite and non-pyritic Fe and 8 were measured
for soil profiles at a streamside (8 8 ) and inland (IL) landscape position, within
the saline (8 ), brackish (B), intermediate (I) and fresh (F) marshes.
The organic layer was comprised of a variable number of subhorizons
and their thickness varied widely within a degrading marsh. Accretion
differences between 8 8 and IL are the main source of spatial variability, which
forms more subhorizons at 8 8 than at IL. Deposltional differences that
occurred during formation of the mineral horizon may have left depressions
within the marsh. The organic layer is thicker and the mineral layer is found
deeper within these depressions. 8 oil bulk density (BD) was lower in the
brackish marsh compared to the saline marsh. 8 alinity profiles differed widely
between landscape positions within the inland landlocked site. Influence of
86
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
salinity on pyrite accumulation was variable within the profile. Pyrite content
within the surface horizon was spatially variable. Salinity effect on pyrite
accumulation was dominant for subsurface horizons. More pyrite accumulated
within the profiles of the saline marsh. A thin layer of dark organic material that
occurred immediately above the mineral layer contained the highest pyrite
content within the soil profiles. Non-pyritic Fe contents were significantly
different between the landscape positions within the more saline marshes. The
non-pyritic Fe content could be used as an indicator to assess marsh status.
The landlocked inland sites retained more non-pyritic Fe within sub surface
organic layers due to limited pyritization. Non-pyritic S content within the
organic subhorizons differs significantly between marshes due to the changes
in salinity. The saline marsh contains more non-pyritic S. Soil pH differences
are more pronounced between marshes. The pH for the organic subhorizons
does not vary within the profile. The mineral layer pH was always higher than
that of the organic subhorizons.
Pyrite framboids detected only within the saline marsh organic
sediments, were 6 to 8 pm in diameter. The sediments at both saline and
brackish marshes exhibited a mixed mineralogy with smectite, illite, and
kaolinite clays. Pyrite also was detected from XRD patterns for the sediments
at both marshes, while the coarser fraction ( < 2 0 pm) contains more pyrite.
These organic soils should be reclassified to indicate sulfidic materials within
87
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
the profile. The pyrite determination technique used in this study can be used
to characterize sulfidic material within the soils.
Coastal marshes provide a favorable condition for pyrite formation
because of their characteristically highly chemically reduced environment.
Sulfate is reduced to sulfide, and with the availability of ferrous ions, pyrite is
formed. Acid sulfate soil conditions can be formed if the soils with pyrite are
drained (Fanning and Fanning, 1989; Dent, 1993), which would be a highly
unlikely event for these lands. However, dredging occurs in this region
associated with the oil and gas industry. This activity can expose the pyritic
material that could be oxidized and eventually produce acidity. Therefore,
information on the amount of pyrite within the soil profile is important when
making land management decisions because of the potential acidity from the
dredged material. Acidity in combination with salinity (Fanning, 1993) can
adversely affect plant productivity and eventually may contribute to marsh loss.
The adverse effects of these soils could extend into the adjacent aquatic
ecosystems and limit the alternate use of these lands. Outbreaks offish
disease and massive fish kills in the water bodies were reported when they
were polluted by water draining from the acid sulfate soils (Lin and Melville,
1994).
Pyrite is the most stable and prevalent sulfide phase occurring within
coastal marsh soils (Berner, 1964; Lord and Church, 1983; Rabenhorst and
James, 1992). Pyrite remains inactive if it is kept submerged and reduced
within the marsh. Pyrite formation can be spatially and temporally variable
88
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
within the marsh due to variations of sulfate, reactive ferrous, organic matter
content and microbial activity. Sulfate supply can be variable, but closely
related to salinity within the marsh because seawater carries sulfate into the
ecosystem. Marsh types are delineated based on salinity levels (Feijtel et al.,
1988; Soil Conservation Service, 1989). Seawater intrusion, when extended
into the marsh due to sea level rise, enhances the sulfate supply into the
marsh. Sulfur dynamics also are important for the energy flow within this
coastal environment (Whitcomb et al., 1989).
This study evaluated the influence of salinity on pyrite accumulation and
to compare the accumulation of pyrite and non-pyritic Fe and S between two
landscape positions; namely streamside and inland areas within the marsh.
Mineralogical evidence also was sought to detect pyrite within these soils.
4.2 Literature Review
4.2.1 Marsh Loss around Baraterie Bay Basin, Louisiana
Marsh loss has occurs in the northern Gulf of Mexico at a high rate
(Turner, 1990). Marshes undergo rapid submergence that is associated with
the relatively high rate of apparent sea level rise. Conversion of brackish
marsh to saline marsh due to seawater intrusion is common in southeast
Louisiana. Marsh longevity depends partly on the deposition of mineral and
organic matter. Mineral matter accumulation is critical and directly proportional
to biomass production. Salinity influences mineral and organic matter
accumulation (Nyman and DeLaune, 1991; Chmura et al., 1992; DeLaune et
al., 1993; DeLaune et al., 1994; Nyman et al., 1994a). The sulfate content
89
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
increases with increased salinity, and marshes become more liable to sulfide
toxicity (Nyman et al., 1993b).
Two major mechanisms shown to cause marsh loss are peat collapse
and erosion below the living root zone (Nyman et al., 1994a). Peat collapse
occurs following a “hotspot” pattern (DeLaune et al., 1994); a hotspot is an area
within the marsh that experiences rapid loss (Nyman et al., 1993c). Peat
collapses because of the disintegration of the living root network resulting from
root mortality. This is associated with salinity increase and water logging.
Reduced surface elevation of peat forms ponds within the marsh. Hotspots are
common within brackish areas that are converting to saline marsh. Less
frequent occurrence of sedimentation events by winter storms results in
inadequate vertical accretion, and soil bulk density is too low to support
Spartina a ltem iflora. The most common marsh loss pattern, the scattered
broken marsh interior, is less severe than the less common concentrated
hotspot pattern. Marsh loss mechanisms are spatially variable within a
relatively small region (Nyman et al., 1993a, 1994b).
4.2.2 Seawater Intrusion, Salinity and Marsh Types
The isohaline data for the east and central Barataria Bay ranges from
over 20 ppt to less than 0.5 ppt (Soil Conservation Service, 1989). The
marshes around the Barataria Bay have been delineated into saline, brackish,
intermediate, and fresh water marshes based on salinity. Fresh and
intermediate marshes occur below 5 ppt. Brackish marshes occur between 5
and 10 ppt while salt marsh is found at salinity above 10 ppt (Feijtel et al., 1988;
90
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Soil Conservation Service, 1989). The species diversity increases with
decreasing salt concentration (Darmody and Foss, 1979). Typha spp. (cattail),
Spartina cynosuro ides (big cord grass), and Pontederia cordata (pickerel weed)
occupies the low salinity areas of the marsh while Scirpus o iney i (three square),
Spartina pa tens and Spartina a ltem iflora are found within high salinity areas
(Darmody and Foss, 1979). Increasing salinity decreases growth of Spartina
a ltem iflo ra and decreases transpiration and plant biomass. Ion exclusion,
secretion, and accumulation are three major salt tolerant mechanisms.
Inhibition of K uptake at high Na concentrations adversely affects plant growth.
Salt glands are an additional mechanism that enabled plants to secrete excess
internal salts. S. a ltem iflora selectively secretes Na relative to K (Bradley and
Morris, 1991). Spartina a ltem iflora grows optimally in the salinity range of 0-20
ppt, but salinity above 40 ppt adversely affects survival (Bradley and Morris,
1991). Increasing salinity above 10 ppt reduces growth of brackish marsh
species, Spartina o ineyi and Spartina patens, while Spartina o iney i is
drastically affected (Broome et al., 1995). The mechanisms adopted are
species dependent. Spartina pa tens tolerates high Na concentrations by ion
secretion while ion accumulation is the dominant salt-tolerance mechanism for
Spartina o iney i (Broome et al., 1995). Presence of toxic levels of elements and
gases is another stress for plants growing within these soils. Resistant plants
contain high concentrations of elements within their roots compared to the
shoots (Rozema et al., 1985). Spartina a ltem iflora tolerates sulfide uptake over
a long growing season through an internal oxidation or detoxification
91
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
mechanism (Carlson and Forrest, 1982). Sulfide concentration gradient
associated with slight elevation changes results in plant productivity and
mortality variations (DeLaune et al., 1983).
4.2.3 Pyrite Formation and Accumulation
Increased oxygen consumption in submerged organic soil and restricted
oxygen supply due to flooding creates a low oxidation-reduction potential within
the soil. With the disappearance of oxygen in the system, alternate electron
acceptors become active. Sulfate reduction becomes prominent after depletion
of nitrate, manganic and ferric compounds in the system (Ponnamperuma,
1972; Patrick and Jugsujinda, 1992; Rabenhorst and James, 1992). Labile
organic carbon sources are the major regulator of the soil reduction process
(Connell and Patrick, 1969; Rabenhorst and James, 1992). Ferric is reduced to
ferrous, which is readily mobile within the system as it diffuses along the
concentration gradient. Sulfate also diffuses into the reduced zone along the
concentration gradient supported by thermal mixing. This sulfate reduction
process is called sulfidization (Eq. 4.1 to 4.3), and pyrite is a byproduct of
sulfidization (Fanning and Fanning, 1989; Rabenhorst and James, 1992):
2 CH3-CHOH-CHOH + SO4- ===> 2 CH3COOH + HCO3 +HS + H3O [4.1]
F e " +H S +OH ==> FeS + HjO [4.2]
Fez03 + 4 SO4- + 8 CH2O + 1/2 Oz==> 2FeSz + 8HC03' + 4 H2O [4.3]
Pyrite forms by various processes (Rickard, 1970):
92
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
1.0 Homogeneous ionic reactions
Fe% „) + S"-(3q, ===> FeSz;,) [4.4]
2.0 Solid-Fe reactions
2.1 Mackinawite-polysulfide exchange
Fe%q) + S fp * ===> FeS,„ [4.5]
FeS(c) +S'-(3q) ===> FeS;;,) [4.6]
2.2 Goethite sulfidation
2FeOOH(c, + 3 H 2S ,3q) ===> 2FeS(„ + S“ + OH ^q, + SH^O [4.7]
3. 0 Homogeneous solid-solid reactions
An irreversible conversion of marcasite to pyrite.
4. 0 Heterogeneous solid-vapor reactions
Sulfur oxidation of pyrrohtite can result in the formation of pyrite.
Coastal marshes favor soil pyrite formation because tidal water provides
sulfate to the highly reduced marshes where soluble ferrous is apparently
abundant. Organic matter accumulation, existence of highly reduced
conditions, availability of excess sulfate, 8 reducing bacteria, ferrous ion
concentration, and fluctuation of redox potential (partial reoxidation of S")
promote sulfate reduction and pyrite accumulation (Pons et al., 1982). The rate
of pyrite formation varies depending on the availability of ferrous ions and 8,
and anaerobic conditions. Pyrite may not be formed despite the abundance of
sources if the organic carbon source is limited. Removal of HCOq" from the
system promotes pyrite formation (Fanning and Fanning, 1989). 8 u If ate
reduction produces carbonates that can be precipitated as CaCOg (Ogata and
93
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Bower, 1965). Dissolved S concentration of less than 320 ppm limits pyrite
formation (Goldhaberand Kaplan, 1982). Depending on the pH, sulfate
reduction could occur within the Eh range o f +110 and -500 m V (Baas Becking
and Moore, 1961).
Marsh sediments contain both Fe sulfide (FeSg-Fe) and Fe oxide (free
Fe) phases, depending on the redox potential (Griffin et al., 1989).
Noncrystalline Fe oxides rather than crystalline Fe oxides become reduced by
bacterial activity (Munch and Ottow, 1980). Munch and Ottow (1980)
suggested that the Eh drop and change in pH should be regarded as a
consequence, rather than the cause of Fe reduction by bacteria. The degree to
which the reactive Fe has been used for pyrite formation is termed as degree of
pyritization (Py).
Py = FeSg-Fe / (FeSg-Fe + free Fe) [4.8]
Ferrous-Fe precipitates as siderite (FeCOg) unless pyrite is formed (Rickards,
1973). The reactive ferric minerals in the solid phase are important in the
formation of the reactive ferrous portion. Crystalline Ferric minerals are present
at depth within the salt marsh at Lewes, Delaware (Kostka and Luther, 1994).
Mineral precipitation varies within the marsh due to variable ionic concentration
of porewater (Giblin and Howarth, 1984; Feijtel et al., 1988). This produces
micro site variability within the marsh soils (Rabenhorst and James, 1992).
Possible mineral formation can be evaluated from ion activity products of the
porewaters (Giblin and Howarth, 1984). All porewaters are supersaturated with
respect to pyrite (FeSg) and hauerite (MnSg) for the Barataria Bay marshes.
94
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Ironsulfide equilibrium indicates super saturation at surface (3 to 5 cm) but
undersaturation at 2 0 cm within brackish and salt marsh sediments of the
Barataria Bay (Feijtel et al., 1988). Rickard (1975) also shows that pyrite
rapidly forms as follows:
Fe^" + S jS"-+ HS- ====> FeSg + S,S^' + H* [4.9]
4.2.4 Sulfur Dynamics within the Marsh
The major processes involved in 8 dynamics are biological assimilation,
mineralization and biogeochemical transformations. The latter is mainly a
redox-controlled process, which includes both reduction and oxidation
reactions. Sulfur occurs in various oxidation states and redox controls solubility
and mineral formation (Lindsay, 1979). Chemical equilibrium in interstitial
water can be indicative of authigenic mineral formation (Giblin and Howarth,
1984; Feijtel et al., 1988; Gaillard et al., 1989). The inorganic form of S
changes with Eh as sulfides at -2 0 0 mV, elemental S at 0 mV, and sulfate at
+600 mV of Eh. There are many other forms of inorganic 8 that occur during
transformations. Sulfate is added continuously by seawater into the coastal
marsh ecosystem. Pore water 8 is at equilibrium with soil matrix 8 . The
gaseous forms of 8 produced by these processes are HgS, CH 3SH, (C H 3)2S,
COS, and CSg (Crozier et al., 1995). Organic and inorganic 8 comprise the
soil 8 pool within the marsh. The organic 8 portion is much larger compared to
the inorganic 8 fraction. The two organic fractions are the 8 directly bonded to
carbon (carbon-bonded 8 ) and ester sulfates that are not directly bonded to
carbon (Freney et al., 1970). The carbon-bonded 8 includes the 8 of cysteine,
95
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
cystine and methionine. The inorganic S fraction includes four S species: HCI
soluble S, acid volatile S (AVS), elemental S, and pyrite S. The HCI soluble S
represents the soil sulfates and sulfides produced during sulfate reduction.
Sulfide is mobile and can be evolved as H jS and reoxidized forms, or can be
precipitated as Fe monosulfides and pyrite (Whitcomb et al., 1989). The AVS
fraction includes H^S and Fe monosulfide (not pyrite), elemental or organic-S
(Howarth and Merkel, 1984). Sulfide reoxidation may occur at the root surface
or the soil surface. This oxidation reaction can either be biological (Grant and
Bathmann, 1987) or chemical (Whitcomb et al., 1989); both produce elemental
S. Dissolved elemental S can be combined with sulfides to form the polysulfide
ions that are unstable and will transform into elemental S with further oxidation.
If reducing conditions prevail, polysulfide ions will be reduced, or else Fe** or
FeSz will form. The internal S oxidation-reduction cycles for this environment
prevents the release of HgS into the atmosphere (Whitcomb et al., 1989).
However, Crozier et al. (1995) indicates that production of S gas is positively
correlated with the initial sulfate concentration. Soils retain HgS, and the
sorption capacity is influenced by the quantity of Fe oxides present within the
soil (Bohn et al., 1989). Variation of these 8 species can indicate the S
dynamics for the marsh (Krairapanond et al., 1991a, 1991b, and 1992). The
lack of information for gaseous 8 emission and plant uptake can lead to an
erroneous conclusion as to what processes are responsible for the 8 dynamics.
Organic S is considerably higher than the inorganic 8 pool for all three
marshes within the Barataria Bay marshes (0-50 cm depth) (Krairapanond et
96
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
al., 1991a, 1991b, and 1992). Carbon bonded S is the dominant portion of the
organic S pool. Organic carbon can be highly correlated with total S because
of sulfate retention by organic matter (Haering et al., 1989). The AVS accounts
for <1% of the total 8 while HCI soluble 8 accounts for most of the inorganic 8
pool for all three marshes. Pore water sulfate is significantly correlated with
HCI soluble 8 . Inorganic 8 fraction is 22% for fresh, 13% for brackish, and 24%
for salt marsh. Reduced 8 species, except elemental 8 , increases seaward
along the salinity gradient. Pyrite 8 and elemental 8 account for 8-33% of the
inorganic 8 pool within the brackish marsh. No clear pattern of pyrite 8
formation was observed for the upper 2 0 cm of the soil profile within the fresh
water marsh. At this depth, peak elemental 8 concentration coincides with
peak plant root density.
Pyrite 8 and elemental 8 account for 6 to 21% of the inorganic 8 fraction
within the fresh water marsh (Krairapanond et al., 1991a). Pyrite 8
concentration represents <3% and <2% of total 8 for the fresh and the saline
marshes, respectively (Krairapanond et al., 1991a, 1991b). Pyrite is the major
8 form for most of the streamside organic horizons, while organic 8 was
dominant within inland pedons for Chesapeke Bay marshes (Haering et al.,
1989). Thiosulfate (8 2 0 3 ) and sulfite (8 0 ^ ^ are in equilibrium with elemental
8 (8 °) during H2 8 oxidation in porewaters of Danish salt marsh profiles
(Thamdrup et al., 1994). Redox conditions fluctuate vertically within marsh
soils, producing seasonal 8 species variation (Feijtel, et al., 1988). Therefore,
97
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
the responsible processes can be assumed based on the knowledge of S
dynamics. Inverse relationship between ester-sulfate S and HCI soluble S
could indicate S mineralization while AVS oxidation can increase HCI soluble S.
High elemental S concentrations can indicate a previous oxidation history of
reduced layers, most importantly the transition of oxidized and reduced layers
within the profile (Krairapanond et al., 1991a, 1991b, 1992). Table 4.1 presents
absolute S estimates for different marsh types from Krairapanond e ta l. (1991a,
1991b, 1992). Sulfur species vary widely between marsh types. Organic S
content is similar between brackish and salt marshes, but is the lowest for the
fresh marsh. High organic S indicates high S assimilation by the marsh
vegetation. Inorganic S species show much higher variation compared to
organic pool for different marsh types. Total soil S content varies considerably
among marsh types. Fresh marsh contains 5.7 ppt S brackish marsh 15.6 and
salt marsh 15.7 ppt S (Krairapanond et al., 1992).
Table 4.1. Sulfur species (ppm) variation in 0-50 cm depth for different marshes, in the Barataria Bay, Louisiana.
Marsh AVS HCI-S S° Pyr-S Ester-S C-S Total-S
Fresh 1 1 1083 91 1 0 0 1180 3249 5700
Brackish 30 1544 84 314 3619 10000 15600
Salt 24 3250 272 245 3313 8588 15700
98
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
4.2.5 Pore Water Dynamics and Mineral Formation
Mineral precipitation can be variable within the marsh due to variable
ionic concentrations in porewater (Giblin and Howarth, 1984; Feijtel et al.,
1988), and mineral formation can be evaluated from ion activity products of the
porewaters (Giblin and Howarth, 1984). All pore waters are supersaturated
with respect to pyrite (FeSg) and hauerite (MnSg) for the Barataria Bay marshes.
Ironsulfide equilibrium indicates super saturation within the surface (3 to 5 cm)
but undersaturation at 2 0 cm within brackish and salt marsh sediments of the
Barataria Bay (Feijtel et al., 1988). The study by Giblin and Howarth (1984)
includes examination of the formation of FeS (amorphous), FeS (mackinawite),
Fe^S^ (greigite), FeSg (pyrite), MnS (alabandite), FeCO^ (siderite), M nCOj
(rhodocrosite), Fe3(P 0 4 ) 2 (vivianite), and Mn3(P O j 2 (reddingite) based upon
chemical equilibrium. Giblin and Howarth (1984) indicate that pore waters are
undersaturated with respect to all Fe monosulfide minerals, Mn3 (P 0 4 ) 2
(reddingite), and siderite (FeCO j) for the Great Sippewissett marsh,
Massachusetts. But the porewaters are supersaturated with respect to pyrite
(FeS 2), and pyrite is formed as a result of oxidation of polysulfides and
elemental S, rather than the conversion of FeS to FeS 2 (Giblin and Howarth,
1984). Rickard (1975) also shows that pyrite rapidly forms as follows:
Fe"" + S5S"- + HS ====> FeS2 + 8 4 8 "-+ H" [4.10]
4.2.6 Pyrite Crystal Formation
The rapidly formed pyrite occurs as small single crystals (Rabenhorst
and James, 1992). Feijtel et al. (1988) observed single euhedral pyrite
99
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
particles on external root walls in salt marsh samples. Kosters and Bailey
(1983) reported the occurrence of framboidal pyrite within the heavy fraction of
the marsh soil from Barataria Bay. Framboidal pyrite results from the reaction
of Fe monosulfides and elemental S (Raybould, 1973). Framboids are circular
or slightly oval in cross section, and can be assumed to be spherical or sub-
spherical. Framboids can vary in size (Raybould, 1973; Rickard, 1970). Iron
framboids that do not contain S (i.e., HFeO j) can coexist with pyrite (Giblin and
Howarth, 1984). Raiswell et al. (1993) proposed a 3-D diffusion-with-
precipitation model to predict pyrite precipitation when a spherical mass of
organic matter, producing HgS by sulfate reduction, is surrounded by
porewaters containing dissolved Fe. This model indicates the need of high
dissolved Fe concentrations to react with higher amounts of reduced S from
large organic masses to form pyrite at decay sites. The maximum size of
sphere of organic matter that can be pyritized is about 50 pm in radius that is
close to the radius of framboidal pyrite. However, Raiswell et al. (1993)
indicated that the exposure times are important in this pyritization process.
4.2.7 Spatial Variability of Pedogenic Processes
The salinity gradient along the marsh landscape maintains the S
gradient into the marsh ecosystem of Barataria Bay Basin. Pyrite formation can
be variable in relation to the marsh landscape position (Pons, 1973; Griffin and
Rabenhorst, 1989; Haering et al., 1989; Lin and Melville, 1994). Variation in
available sulfate and ferrous compounds, and oxidation-reduction status within
100
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
the marsh can vary pyritization (Griffin and Rabenhorst, 1989; Haering et al.,
1989; Lin and Melville, 1994). The pyrite content is not correlated to total S or
carbon content (Haering et al., 1989) but pyrite accumulation is related to Fe
and S supply (Griffin and Rabenhorst, 1989) within coastal marshes in
Maryland. Pyrite accumulation is favored for streamside profiles that received
Fe inputs from tidal flushing (Haering et al., 1989). The sediments provide
ferrous ions. Pyrite formation can be simulated from models that are based on
availability of sulfate. Eh range, ferrous ion supply, and the soil organic matter.
Pyrite content varies across marshes for Barataria Bay, Louisiana; pyrite is
highest for the brackish marsh and lowest for fresh marsh (Brackish > Salt >
Freshwater marshes) (Feijtel et al., 1988). The change of pyrite content is due
to the seasonal balance between pyrite formation and oxidation. Ion activity
products of the porewaters indicate spatially variable mineral precipitation for
Massachusetts’s marshes (Giblin and Howarth, 1984). Pyrite forms at various
depths of the profile and will remain until it oxidizes. Three distinct zones may
be separated within the profile with respect to pyrite accumulation: a frequently
oxidizable surface layer, a conducive second layer, and a third layer with limited
pyritization (Lord and Church, 1983). Within the transition zone between
oxidized and reduced conditions, more elemental S is found than pyrite S.
However, prolonged droughts can lower the water level by which surface soils
can be naturally drained to a considerable depth. A water table drop during the
day as well as night can be due to water uptake by roots. Oxidation reactions
will occur within the drained portion of the profile as air enters into the surface
101
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
soil (Dacey and Howes, 1984). This promotes pyrite oxidation instead of pyrite
formation. The redox profile fluctuates seasonally within Barataria Bay
marshes (Feijtel et al., 1988). Pyrite formation occurs within the salt marsh
during the summer and fall seasons when Eh values are low. Pyrite can be
completely oxidized during the early spring, which may create acid conditions.
In a brackish marsh, pH and Eh changes govern Fe^^ concentrations, which is
associated with pyrite formation and oxidation. The minimum pH coincides with
increased interstitial Fe" " during the spring (Feijtel et al., 1988). Ion activity
products of the porewaters indicate seasonal variation of mineral precipitation
for Massachusetts’s marshes (Giblin and Howarth, 1984).
4.2.8 Soil Classification and Soil Taxonomy
Organic soiis within the Barataria Bay Basin are mapped as associations
of soil series in the soil survey conducted in 1981 morphology (Soil
Conservation Service, 1984). The associated series within a particular salinity
regime are delineated based on the depth to mineral layer at subgroup level
(i.e., Terric Medisaprists and Typic Medisaprists). Many activities such as
hurricanes, saltwater intrusion, construction of channels, and other man-made
changes, may affect accretion and degradation of organic layers within the
landscape. Reaction classes are considered at family level differentiae of
Histosols in Soil Taxonomy (Soil Survey Staff, 1996). Histosols that have a pH
value of 4 .5 or more in one or more layers of organic soil materials within the
control section for Histosols are differentiated as “Euic” while all other Histosols
102
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
are called “Dysic”. The two major soil series associations that are dominant
within the brackish and saline marshes differ in salinity but have similar
morphology (Soil Conservation Service, 1984). Timbalier-Bellpass association
(TB) is dominant within the saline marsh. According to Soil Taxonomy, the
Timbalier series is euic, thermic, Typic Medisaprists while the Bellpass series is
clayey, montmorillinitic, euic, thermic, Terric Medisaprists. The Lafitte-Clovelly
association (LA) dominates the brackish marsh. The Lafitte soil series is an
euic, thermic, Typic Medisaprists while the Clovelly soil series is a clayey,
montmorillinitic, euic, thermic, Terric Medisaprists. Terric Medisaprists are the
Medisaprists that have a mineral layer 30 cm or more thick that has its upper
boundary within the control section (130 cm) below the surface tier (60 cm).
Other Medisaprists that have the upper boundary of the mineral layer below
control section (130 cm) are Typic Medisaprists. The main difference between
these soil series is the depth to mineral layer. They are delineated based upon
depth to mineral layer.
Previous soil classification has not considered the presence of S
compounds within these soil profiles. Two major diagnostic horizons that are
directly related to S are the sulfuric horizon and the sulfidic materials. A great
group of Histosols, "Hemists", is differentiated into two subgroups as
Sulfohemists and Sulfihemists. The Sulfohemists has a sulfuric horizon that
occurs within 50 cm of soil surface, while the Sulfihemists contain sulfidic
materials within 100 cm of the soil surface. The sulfuric horizon is a soil horizon
that is 15 cm or more thick and composed of either mineral or organic soil
103
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
material that has a pH value of 3.5 or less (1:1 soil:water suspension) and
shows evidence that the low pH is caused by sulfuric acid. The evidence can
be jarosite concentrations, directly underlying sufidic material, or 0 .05 % or
more water-soluble sulfate. Sulfidic materials contain oxidizable S compounds
and are mineral or organic soil materials with a pH of more than 3.5 which, if
incubated a layer of 1 -cm thick at field capacity and room temperature, show a
drop in pH of 0.5 or more units to a pH value of 4.0 or less (1:1 soi!:water
suspension) within eight weeks (Soil Survey Staff, 1996). Sulfihemists and
Medisaprists are reported for the organic soils in Florida, where the Sulfihemists
contains more than 0.75% S in the upper 50 cm (Coultas, 1997).
4.2.9 Pyrite Determination
A suitable method is required for pyrite determination to assess pyrite
accumulations. A few different techniques are available for pyrite
determination. The qualitative determination methods include X-ray diffraction
and Scanning Electron Microscopy. The X-ray diffraction technique can also be
used as a semi-quantitative method to estimate pyrite. The quantitative
determination methods are indirect and either Fe based or S based. Empirical
relations also are proposed (Willett and Beech (1987). Fe based sequential
extraction and differential measurement techniques are used to estimate pyrite.
Sulfur based techniques fractionate S mainly into organic and inorganic S. The
inorganic fraction is separated into four groups as HCI-soluble S (mainly sulfate
and H2S), acid volatile S (AVS) (monosulfides and dissolved sulfides),
elemental S and pyritic S (Begheijn et al., 1978; Krairapanond et al., 1991a,
104
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
1991b, and 1992;). The Fe based estimation involves separation of pyritic and
non-pyritic Fe. This is directly related to the estimation of the rate of pyritization
(Leventhal and Taylor, 1990). More detailed Fe based schemes are used in
acid sulfate soil analysis, where pyrite, as well as jarosite fractions, need to be
estimated separately (Lord, 1982; Raiswell e ta l., 1994). Separation of pyritic
and non-pyritic Fe is sufficient for the scope of this project. The environmental
significance of pyrite accumulation in these ecosystems is limited to the impacts
of dredging. Hence, any pyrite that is accumulated in the soil profile is kept
submerged until the soil is dredged, exposed and allowed to oxidize. There is
no jarosite within the submerged potential in acidsulfate soils. Therefore,
considering the need to estimate pyrite material, a quick and easy method for
separating pyritic and non- pyritic Fe is sufficient. The spatial variability study
assesses the relative variation of pyrite estimates, so the differences are
cancelled. The S-based techniques may contaminate the samples because of
the soluble S from the high salinity of the samples; most of the sea-borne
salinity contains S in the system. Lord (1982) suggested a selective extraction
method for pyrite determination. The HF-H3BO3 solution used for silicate
dissolution dissolved pyrite and required correction factor to adjust for pyrite
content. The indirect estimate of pyrite is based upon the separation of pyritic
and non-pyritic Fe, which is adequate for this study (Schneider and Schneider,
1990). Therefore, their method used for pyrite estimation in coal and ceramics
is appropriate for this experiment.
105
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
4.3 Materials and Methods
4.3.1 Site Description and Sampling Procedure
Two landscape positions, namely streamside (8 8 ) and inland (IL) were
sampled from each site. Four sites were selected to represent each marsh
type, saline (8 ), brackish (B), intermediate (I) and fresh (F) within the Barataria
Bay Basin (Figure 4.1). 8 ite names will be abbreviated as “8 8 8 ” for streamside
(8 8 ) at the saline marsh (8 ) and “8 IL” for inland at the saline marsh (8 ) and so
forth. Three soil profiles were sampled from each landscape position.
8 treamside profiles were selected 1 to 3 m from the water edge of the marsh.
Inland profiles were selected about 30 m from the streamside. A MacAully
auger (Day et al., 1979; 8 heppard et al., 1993) was used to extract soil cores
from the surface to below the first mineral soil layer or to a depth of 1.50 m.
8 oil horizons were designated according to 8 oil Taxonomy (8 oil 8 urvey 8 taff,
1996), and soil samples were collected from each subhorizon down to the
mineral soil layer. 8 oil samples were stored in an ice-filled cooler in the field
and in a cold room until they were analyzed.
8 oils were sampled separately for bulk density from the different
horizons using centrifuge tubes. Capped centrifuge tubes of 60 mL were
prepared by puncturing the bottom tip and brought to the field. The tubes were
filled completely with soil with minimum possible disturbance. The hole in the
bottom helped avoid air trapping. The soil-filled tube was capped and wrapped
with a polythene bag and brought to the lab in an ice-filled cooler.
106
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD■DOQ .C
gQ .
■DCD
C/)C/)
8■D
91*00' 00*30' 90*00* 80*30*
3.3 "CD
CD■DOQ .C
aO3"Oo
CDQ .
■DCD
C /)C /)
30*00* —
20*30* -
BARATARIA BASINL o u lô in r t a
Dartlarla Baaln
Vagotation
N o iu ro l l«va« i(U /bo n . AnnCulium l A rc o i
ond fio llom laod H ardw ood fo r e t l i
fkp y-: I f o r a i l td Walksnd(Swomp)
M a rih
[J .] In l*(m *d ia t* M orih
I " 1 fiiocliih M o /ik
I I Satin* M oftk
Figure 4.1 A map showing different marsh types within the Barataria Bay Basin (after Krairapanond et al., 1992).
Tubes with soil were weighed and placed in an oven at 55°C. After drying, dry
weight was used to measure the bulk density. Bulk density data were
estimated only for saline and brackish marsh sites.
4.3.2 Measurement of EC and TDS
W ater samples were collected from different water bodies within the
Barataria Bay Basin to cover a wide range of salinity. Samples were brought to
the laboratory in an ice-filled cooler and filtered (Whatman No. 42). These
samples were used to measure electrical conductivity (EC) and total dissolved
solids (TDS). The EC of the water samples was measured using a Corning M90
conductivity sensor (Corning Inc., Corning New York 14831, USA). A volume of
30 to 60 mL from each water sample was weighed and slowly evaporated in a
centrifuge tube at a temperature between 55 to 65 °C in an oven, cooled in a
desiccator and weighed. The TDS were estimated on a dry weight basis for
each sample in triplicate.
4.3.3 Pyrite and Non-pyritic Fe and 3 Determination
The method used for pyrite estimation in coal and ceramics by
Schneider and Schneider (1990) was modified for the analysis of extractions for
Fe by the ICP-AES. Six scoops (1/8 tsp.) of soil were measured into six
digestion tubes that were calibrated to 50 or 75-mL volume. Tubes were
separated into two batches; one was for non-pyritic (NP) and the other set was
for pyritic (P) and non-pyritic (NP) Fe digestion. The 50-mL tubes were used
for non-pyritic Fe, while the 75-mL tubes were used for pyritic and non-pyritic
108
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Fe. A sample was placed at the bottom of the tube. Six mL of concentrated
HCI was added to each tube with soil, under a fume hood and the tube was
covered with a small glass (“reflex") funnel. The soil was stirred within the acid
to make a suspension and left over night, covered with "reflex" funnels. Then,
23 mL of deionized water (D l) was added into each tube. The digestion
procedure was different for “NP” and “NP+P” sets, therefore they were digested
separately. To digest the NP set, the sample was placed onto the digestion
block, and the block heater was turned on. It took about 15 to 20 min to start
boiling. The samples were kept boiling for 1 h and were removed and allowed
to cool. The tubes were filled to the 50 mL level with 1:10 HCI then mixed well
and filtered through #5 (or #42) Whatman filter paper. The filtrate was highly
acidic; therefore, it was diluted six times to reduce the acidity and to increase
the detection levels by the ICP.
For the “NP+P” set, after adding 23 mL of water, the sample was boiled
for 30 min and then 25 mL of 3N HNO3 was added to each tube while they
were on the digestion block. Acid was slowly added through the funnel. It took
another 10 to 15 min for the mixture start boiling. Samples were boiled for
another 30 min and cooled. The tubes were filled up to the 75-mL level with 2N
HNO3 then mix well and filtered through #5 (or #42) Whatman filter paper. The
filtrate was highly acidic; therefore, it was diluted six times before analysis by
the ICP. The pyritic Fe content was determined based on the difference
109
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
between Fe content of “NP+P” and “NP” digestions. The pyrite content was
estimated using the equation 4.11.
Fe (mg L'^) * 2.146 = FeS2 (mg L'^) [4.11]
Fe and S content from the “N P” digestion were the non-pyritic Fe and S
(Schneider and Schneider, 1990).
4.3.4 Measurement of soil pH
The pH was measured directly using a combination pH electrode with
pH/mV meter (Orion Research model 701A/digital lONALYZER). Soil pH was
measured in triplicate in soil water suspensions in the laboratory for each soil
horizon.
4.3.5 Microanalysis of Marsh Soils
Small soil samples were oven dried at 55 °C for a few days to remove
water from the samples and prepared for the SEM analysis. The samples were
gold coated and mounted on the SEM rod mounts for examination (Welton,
1984).
Surface sediments were collected from the streamside of saline (SSS)
and brackish (BSS) marshes. Smears were prepared for X-ray diffraction
analysis for two size fractions, less than 2 0 and less than 2 pm, with minimum
disturbance (treatment) to samples. The samples were dispersed with sodium
phosphate to preserve any Fe and carbonate minerals. The less than 2-pm
and 20-pm size fractions were separated by gravity sedimentation. Clays were
concentrated by centrifuging. XRD patterns were obtained for each sample
110
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
under air dried, ethylene glycol saturated, and heated (to 300 and 550 C)
treatments (Moore and Reynolds, 1989). The XRD patterns were obtained
from Cu Ka (40 KV, 30 mA) using a Siemens D5000 instrument. Differential
X-ray diffraction (DXRD) patterns were analyzed for Fe minerals, especially
pyrite (Schulze, 1981; Lord, 1982).
4.3.6 Data Analysis
Statistical analysis included mean comparisons, ANOVA, and regression
analysis using the Statistical Analysis System (SAS Institute Inc., 1994).
Random effect analysis of variance was conducted from a completely nested
design with two factors: site, which represented salinity effect, and the
landscape position, including streamside and inland positions. The random
effect model had the following form (SAS Institute Inc., 1994).
Yijr = H + tti + pij + 8 |jr
W here
ijr is the value of the dependent variable observed at the rth replication with
the first factor at its i th level and the second factor at its j th level.
p is the overall (fixed) mean of the sampling population.
tt| Pij 8 |jr are mutually uncorrelated random effects with zero means and
respective variances 0 2 - ^^3 - and (the variance components).
Each variable for every horizon was analyzed separately in a nested design
and mean comparisons were performed only for the pre-planned pairs of
111
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
means. Any treatment effect is expressed as significant relative to confidence
level (a ) of 0.05, unless the p-value is presented.
4.4 Results and Discussion
4.4.1 Soil Horizon Thickness and Bulk Density
Organic soil layers were comprised of distinct subhorizons designated as
G a l , Ga2, G a3 horizon, and etc. The number of subhorizons varied within the
landscape position, as well as, between the sites. The underlying mineral
horizon was designated as Cg due to gleying; in some cases, a thin mineral
layer was separated based on texture (i.e., C g l and Cg2). A thin layer of dark
organic material occurred immediately above the Cg horizon with a strong
sulfide smell.
Table 4 .2 presents the average thickness of every horizon at the two
landscape positions at each marsh type. Average thickness of the Ga1 horizon
ranged from 10 to 38 cm. Thickness of the G a l horizon was similar between
the landscape positions at all marsh types except at the intermediate marsh
that was degrading. The lowest G a l horizon thickness (10 cm) at ML and the
highest G a l horizon thickness (38.3 cm) at ISS may be indicative of the current
degrading status at this location. Disintegration of the root network may cause
high erosion with further dispersion due to Na that is brought in with seawater.
Gtherwise consolidation of collapsed material may occur within the G a l horizon
at ML. Eroded material from inland may have been deposited at streamside in
addition to the degradation at the streamside. Inland may not experience any
112
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD■DOQ .C
gQ .
■DCD
C/)Wo'303CD
8■D( O '3"
13CD
3.3 "CD
s i■D WoQ .CaO3
■DO
CDQ .
■DCD
I(/)Wo'
Table 4.2. Average thickness of different sub horizons of soil profiles at different landscape positions.
Marsh Type Saline Brackish Intermediate Fresh
Horizon Streamside Inland Streamside inland Streamside inland Streamside inland(SSS) (SIL) (BSS) (BIL) (ISS) (IIL) (FSS) (FIL)
0 a 1 28.3 ± 5 .8 t 26.7 ± 7.6 28.3 ± 7 .6 31.7 ± 7 .6 38.3 ±18 .9 1 0 . 0 ± 0 . 0 33.3 ± 2 .9 36.7 ± 1 1 .5
Oa2 28.3 ± 5.8 36.7 ± 23.6 31.7 ± 12 .6 33.3 ± 5.8 45.0 ± 26.5 53.3 ± 2 .9 38.3 ± 7 .6 40.0 ± 8 .7
Oa3 31.7 + 2.9 38.3 ± 2 .9 30.0 ± 5.0 35.0 ±1 3 .2 35.0 ± 22.9 68.3 ± 1 0 .4 38.3 ± 5 .8 33.3 ± 2 .9
Oa4 26.7 ± 7.6 18.3 ±16.1 15.0 ± 15 .0 21.7 ±2 0 .2 25.0 ± 25.0 1 8 .3 ± 1 1 .5 0 0 . 0 0 0 . 0
OaS 06.7 ± 5 .8 0 0 . 0 06.7 ±1 1 .5 0 0 . 0 06.7 ±11 .5 0 0 . 0 0 0 . 0 0 0 . 0
DML 121.7 ± 5 .8 120.0 ±1 3 .2 111.7 ± 2 .9 121 .7± 2 .9 >150 >150 1 1 0 . 0 ± 0 . 0 1 1 0 . 0 ± 0 . 0
t Mean ± Standard Deviation
re-deposition because the material is eroded away. The remaining material
within the 0 a 1 horizon may be compacted by the standing water at inland sites
when inundated. The thickness of the 0a1 horizon was very uniform at inland
but highly variable at streamside (Table 4.2). The variation in deposition and
sedimentation rates may cause the variability at streamside. The processes,
such as erosion and re-deposition, may create high spatial variability within the
marshes. Studying the spatial variability and identifying the associated patterns
within the landscape may help to understand the mechanisms of marsh loss.
The marsh degradation at IIL may be associated with seawater intrusion, loss
of vegetation, and lack of accretion, and eventually undergo local submergence
(Chmura et al., 1992; DeLaune et al., 1993;DeLaune et al., 1994; Nyman et al.,
1994b). This is following the most common marsh loss pattern, the scattered
broken marsh interior, which is less severe (Nyman et al., 1993a, 1994b). Re
deposition of the material within a close proximity may rate this loss as less
severe damage.
The Oa2 horizon thickness ranged from 28 to 53 cm for all marsh types.
Intermediate and fresh marshes had thicker Oa2 horizon. The Oa3 horizon
thickness ranged from 30 to 6 8 cm for all marsh types. The thickness of the
Oa3 horizon at inland was greater than that of streamside for all marsh types
except for the fresh marsh. The IIL had the thickest Oa2 and Oa3 horizons
despite its thinnest O a l horizon. This may indicate accumulation of organic
material either due to high accretion rates experienced before or concentration
of disintegrated material from degrading surrounding marshes. The fresh
114
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
marsh site had only three organic subhorizons. The Oa4 horizon thickness
ranged between 15 to 27 cm. The OaS horizon was very thin (about 7 cm) and
occurred only at SSS, BSS and ISS.
Depth to the mineral layer (DML) was thin at the fresh marsh site (110
cm) and it was deepest at the intermediate marsh (deeper than 150 cm). The
DML was equal to the total organic layer thickness. The deepest DML at the
intermediate marsh was associated with thicker Ga2 and Ga3 horizons, which
may be a depression at the surface of the mineral horizon. This can be due to
depositional differences when the mineral horizon was formed. This location
may be within an area that is away from distributories. The area closer to the
distributory experiences more mineral matter deposition can eventually form a
marsh with a shallow DML after organic accretions. Whereas, the depression
that is away from the distributory may receive more organic accretions and can
form a marsh with deeper DML. When marsh degrades these depressions
areas may be more vulnerable and can form the open water patches within the
marsh. Thicker subhorizons at this location may be indicative of the local
submergence within the marsh associated with marsh loss. Therefore, open
water patches with thicker subhorizons within marsh may be characteristic of
“hotspots” that are degrading or vulnerable marshes. This may be considered
as an indicator to assess marsh status. The relationship between occurrence
of hotspots and micro relief variations within the degrading marshes needs to
be further studied to test this hypothesis.
115
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Previous investigations mainly studied the surface soil without paying
much attention to the subhorizons and soil morphology of these marshes. The
knowledge of soil characteristics to a particular depth is useful for marsh
management applications therefore, horizon designation from the surface also
seems appropriate. But it should be noted that these organic soils form from
bottom to up, as organic and inorganic accretions are the major soil forming
processes. The present accretions at the streamside can form a distinct Oa1
horizon whereas the present accretions may not be adequate for the inland to
separate the 0a1 horizon that is contemporary to the streamside. The
differences in accretion can be associated with the elevation differences
between the landscape positions (DeLaune et al., 1983). The inland O a l
horizon is more similar to the streamside Ga2 horizon and the inland G a 2
horizon is similar to the streamside Ga3 horizon and so on. Hence, the organic
subhorizon immediately above the Cg horizon at both landscape positions
(either G a4 or Ga5 horizon) can be formed at the same time under similar
environment whereas the G a l horizons at both positions can be different. The
Ga5 horizon was found for streamside but not for inland profiles.
Unequal number of subhorizons may indicate differences in present
accretion and thickness differences between contemporary horizons may
indicate differences in previous accretions, within a healthy marsh. However,
when a marsh degrades an incorporation of two adjacent subhorizons into one
subhorizon may occur. This may form a fewer number of subhorizons and
thicker subhorizons within the profile of a degrading marsh. Understanding the
116
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
characteristics of different subhorizons within the profile reveals information
about its formation and helps to explain the spatial variability of soil
characteristics at a particular depth within the marsh. Therefore, when
comparing subhorizons at different landscape positions it should be noted that
the horizons with similar designation do not necessarily mean that they were
formed under similar environments. This can be a major cause of spatial
variability within the marsh.
Statistical analysis indicated that the thickness of Oa1 horizon (p=0.03)
and O a3 horizon (p=0.02) was significantly different between landscape
positions within the marsh types. However, this difference was found only in
intermediate marsh; Oa1 horizon, p=0.002; Oa3 horizon, p=0.001. Thickness of
Oa2 and Oa4 horizons indicated significant differences between marsh types.
The O a2 horizon thickness at intermediate marsh was significantly different
(p=0.06) from that of saline and brackish marshes. The significant difference
of O a4 horizon between marsh types is mainly due to the absence of Oa4
horizon at the fresh marsh. Depth to the mineral layer was not significantly
different between landscape positions (p=0.30) or between marsh types
(p=0.17). Higher variability of subhorizon thickness and variable number of
subhorizons within profiles may be indicative of high spatial variability organic
layer thickness within a site. Based on the number of subhorizons, the fresh
marsh seems to be less disturbed and stable. Having a higher number of
subhorizons at SSS, BSS, and ISS may indicate a higher degree of disturbance
experienced by the saline, brackish, and intermediate marshes.
117
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Variation in soil BD within the profile is presented in Figure 4.2. The BD
was higher for the saline marsh compared to the brackish marsh for all the
subhorizons. Higher BD may be due to more mineral matter in the sample.
This can be attributed to higher sedimentation rates at the saline marsh
compared to the brackish marsh. Higher sedimentation rates may be expected
due to more sediment supply, as well as, higher flocculation of sediments within
highly saline waters. Lack of sediment feeding to the brackish marshes may
cause low bulk density due to lack of mineral material and eventually low
accretion rates. The mineral layer at site 1 had a BD of 1.08 Mg m'^ compared
to 0.65 Mg m'^ at site 2. BD of the organic layers was very similar for the saline
site (i.e., 0.26 to 0.31 Mg m'^), but at the brackish site, BD varied within the
organic layer (ranged from 0.10 to 0.2 Mg m'^). The BD values are comparable
to those reported by Nyman et al. (1993); they reported mean bulk density for
the top 15 cm of soil as 0.23 Mg m'^ for saline, and 0.12 Mg m'^ for
brackish/saline marshes. The BD variation within the brackish marsh profile
may be due to long-term temporal variations in sedimentation rates.
4.4.2 Soil Salinity
The EC measurements from 1:10, soil:water suspensions were dilution
corrected and converted to salinity as TDS using the relationship between EC
and TDS. The relationship between EC in dS m' and TDS in ppt, was
constructed based on the gravimetric method.
TDS = 0.669 * EC - 0.6208 (r = 0.96) [4.12]
118
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
rg
sz2(0E(A
2mEl
2
i<DC
1
roO
%O
CO(0O o Ü
ooCD
COo
CD
CVJCD
E05
05Q
3CO
mJC2TOEx:
Üm
"Occc0)c
1 0O)
CO5T3
OCO
co
Î>C \j
2305
uozuoH l!os
1 1 9
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Statistical analysis indicated highly significant differences in salinity for
all the subhorizons (p-value ranged from 0.004 to 0.0001) and for the weighted
averages of the profiles (p=0.0001) between marsh types. This confirms that
the sites represented significantly different salinity levels. Mean comparisons
indicated that the salinity for O a l, Ga3, and Cg horizons and weighted average
salinity for the profile were significantly different from each other. The salinity of
the Qa 2 horizon was significantly different except for saline and brackish
marshes. These sites may be under similar salinity regime during the G a2
horizon formation. The saline site had characteristic saline marsh vegetation
and was located within the saline marsh area according to previous maps.
However, the salinity of the SSS and SIL was not within the range of saline
marsh, which is above 10 ppt (Soil Conservation Service, 1989).
Figure 4.3 presents the salinity profiles for the SSS and SIL. Salinity
ranged from 6.36 to 8.40 ppt within the profile at the SSS compared to the
averages of SIL, which ranged from 6.30 to 7.23 ppt. Salinity of the G a l and
Cg were similar at both landscape positions. The SSS had higher salinity
(about one ppt) than the SIL for other subhorizons except the O a l horizon.
This may be attributed to confined or slow water movement between the
landscape positions. Increased salinity of the subhorizons at SIL could be a
result of salt concentration within the root zone when these horizons form.
Plants adapt through different mechanisms to tolerate high salt concentrations
in the root zone (Carlson and Forrest, 1982; Bradley and Morris, 1991). Ion
exclusion mechanism cause concentration of salts within the root zone for salt
120
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CO COm □
CO
CO CL&COQI -
coCO
CM
roO
%O
COCDo O
toCDO o
U O ZU O H VPS
sz%E0)c
m
T3CCD
TJCCD
COCO
mSC/)
11Q.
c15COCO
2 3.g)U_
121
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
tolerant plants (Bradley and Morris, 1991; Latham et al., 1994). Higher salinity
may also be a result of insufficient mixing of pore water within the profile at SIL.
The BSS salinity ranged from 4.70 to 7.01, while at BIL, salinity ranged
from 5.18 to 7.30 ppt. Salinity profiles were very similar at both landscape
positions in the brackish marsh (Figure 4.4). Small streams brought water into
the interior marsh, which maintained similar salinity for both landscapes. This
may be the reason for similar salinity profiles at the BSS and BIL because there
was a small stream running through the BIL. Both the ISS and IIL exhibited
extensive marsh degradation, and the salinity of the ISS ranged from 2.0 to
4.64 ppt compared to 1.47 to 4.95 at IIL. Salinity profiles were very similar for
both landscape positions at the intermediate marsh (Figure 4.5) suggesting free
water movement between landscape positions. More than 2 ppt difference was
observed within the profiles with higher salinity for the subsoil. This may
indicate a local flooding effect as a consequence of marsh loss due to
increased salinity. Figure 4 .6 presents the salinity profiles at the fresh marsh
site, and it’s salinity was extremely low compared to the other sites. Salinity did
not change between profiles at the FSS and FIL, except the FIL Oa2 horizon
had about 1 ppt higher salinity. Weighted average salinity for each soil profile
was estimated to a 150-cm depth (Figure 4.7). Weighted average salinity
ranged between 6 and 8 ppt for brackish and saline marshes. Weighted
averages for ISS and IIL were below 4 ppt. This may be due to the exclusion of
the Cg horizon within these profiles. The FSS and FIL had about 1 ppt
weighted average salinity for their profiles.
122
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
00 CO
00
CD -KQ .Q .
COQt
ÇCO
CO
eg
21
J 3
u2 XI(U
0 -TOc(0
"Oc(0
COCO000)■g
‘ coEs
1CL
CI dCO
T|-2 3 O)
UOZUOH l!OS
123
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
m □
00
CO a.Q.
COQ
ç
I
CM
%E
0)
I0)
■acJ5.5■ocm(O(O
ïcoE3
1Q .
ç"mcoiri
23OJ
UO ZU O H n o s
124
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
m □
00
CO CLsCOQ1-
coco
CM
mE
m(U
. p
T3Cra_c■acCD
COco
Q)2coE3
1
CL
.•S'_c■(ÔcoCD
2 3.rau_
UOZUOH NOS
125
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
00
CO
CVJ
Q.Q .
COQt
c^ := cn CO
EÜom
a.0)
T3CD
2
1Q.CU
2
c"cDW
(UO)2
IS.5)m
N-
2305
e ; is p u B u o jjjs o d a d E o s p u e i
126
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
4.4.3 Pyrite Accumulation and Pyrite Profiles
Pyrite content is expressed volumetrically as mg of pyrite (FeS 2 ) per L of
soil enabling direct comparisons between marsh types despite the BD
variations. Statistical analysis indicated that salinity influenced pyrite
accumulation, but its effect was different from horizon to horizon. Pyrite content
of the Oa1 horizon was significantly different between landscape positions
within the site (p=0.02), but was not significant between marsh types (p=0.50).
Pyrite content within the 0a1 horizon is controlled by the balance of pyrite
formation and oxidation (Feijtel et al., 1988). Therefore, the difference between
sites may not reflect the influence of salinity on pyrite formation. It may be
strongly influenced by the hydrological changes, which affect pyrite oxidation.
Tides, rainfall, and groundwater intrusion influence water level fluctuations
within the marshes (Hemond and Fifield, 1982). Plant water uptake could result
in air entry into the surface soil and sediment oxidation (Dacey and Howes,
1984). However, this may not be significant for these marshes because of the
tidal influence. The mechanism of oxygen diffusion through aerenchyma tissue
from aerial parts of the plant to the roots combined with leakage of oxygen into
rhizosphere is insufficient to overcome high dissolved sulfide toxicity by the
spartina. Internal enzymatic oxidation is responsible for tolerance of high
sulfide concentrations by spartina compared to other plants such as rice
(Carlson and Forrest, 1982). Therefore, it is doubtful whether the oxygen
transported through plants is responsible for pyrite oxidation. Any difference of
127
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
pyrite content within the Oa1 horizon between landscape positions may be due
to the balance of pyrite formation and oxidation. The landscape position
significantly influenced pyrite accumulation at the saline marsh. The mean
value was 4214 mg FeS 2 L" for SSS compared to 846 mg FeS 2 L' for SIL.
This may be due to more oxidation of pyrite within the O a l horizon at the SIL.
Landscape position effect was not significant within other marshes but at the
brackish marsh a lower p-value (0.15) was found when compare the means
between BSS and BIL (2057 vs. 610 mg FeS 2 L'^). This indicates that the
landscape position effect is prominent for highly saline areas. Removal of
HCOg" from the system promotes pyrite formation (Fanning and Fanning, 1989).
High flushing activity may promote pyrite formation at streamside while
accumulation of HCO 3 can inhibit pyrite formation. This can be another reason
for landscape differences of pyrite accumulation. Haering et al. (1989) found
that pyrite accumulation was favored for streamside profiles that received Fe
inputs from tidal flushing. Lord and Church (1983) identified the O a l horizon as
the frequently oxidizable surface layer. Therefore, pyrite oxidation may be
mostly responsible for less pyrite accumulation within the O a l horizon at SIL
compared to SSS.
For the O a2 horizon, neither the marsh type nor the landscape position
significantly influenced pyrite accumulation. This may indicate that pyrite
formation was similar and oxidation due to water table drop did not occur within
the O a2 horizon of the BIL. The landscape position effect on pyrite
128
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
accumulation dramatically diminished (p=0.80) with increasing depth (Oa3
horizon). However, pyrite accumulation by marsh type was significantly
different (p=0.03). Major differences were found between brackish marsh and
other marsh types. The brackish marsh had the highest mean pyrite
accumulation in the O a3 horizon (4365 mg FeS 2 L'^), while the saline marsh
had 1757 mg FeSg L' , intermediate marsh had 1807 mg FeSg L'"' and the
fresh marsh had 1070 mg FeS 2 L ' \
Within the Cg horizon, pyrite accumulation was independent of both
marsh type and landscape position effects. The weighted mean pyrite content
had no influence from the landscape position or site effects; however, the p-
value was low (p=0.17) for the marsh type effects. This indicates the higher the
salinity of the marsh, the higher the accumulation of pyrite within the profile.
Saline and brackish marshes had means over 2500 mg FeS 2 L"\ while the
means for intermediate and fresh marshes were less than 1600 mg FeS 2 L ' \
As revealed by the statistical analysis, pyrite content was five-fold higher
for the O a l horizon at SSS compared to the SIL (4214 vs. 846 mg FeSg L' )
(Figure 4.8). Other horizons within the profile did not show much difference
between landscape positions. However, it should be noted that the
contemporary subhorizons contain similar amounts of pyrite, the SSS OaS vs.
SIL Oa4 and SSS Oa4 vs. SIL Oa3. Higher pyrite accumulation within the SSS
OaS and SIL Oa4 suggests they represent a subhorizon that was formed under
high saline condition. Higher amounts of pyrite for the Cg horizons (4710 at
129
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
w wm □
ooooo
ooo
OOOCD
OOOin
ooo
oooCO
ooorg
ooo
O)E,
IoO
ê>.Q.
£2mEmc13wm
CO
T3CCD
•DCCO
COCO52.CDjg
II11CL
•I>%Û.00
23D)
UO ZUO H n o s
130
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
SSS and 2768 mg FeSg L' at SIL) can be attributed to higher mineral material
within the Cg horizon.
Pyrite accumulation for the brackish marsh indicates a similar pattern of
increased accumulations for the streamside. The Oa3 and OaS horizons
contained more than 5000 mg FeSg L' (Figure 4.9). Pyrite accumulation was
uniform within the organic layer for both landscape positions of the intermediate
marsh and the highest accumulations were found for the bottom organic
horizon (6284 mg FeSg at ISS vs. 5553 mg FeSj at IIL) (Figure 4.10).
Similar to the saline marsh site, ISS OaS and IIL Oa4 seems to represent a
subhorizon that was formed under high saline condition. The Cg horizon was
deeper than 150 cm at both ISS and the IIL and not included for the profile in
Figure 4.10. The streamside data showed more accumulation at all depths.
Pyrite accumulation was minimal for the fresh marsh site except for the
O a2 horizon at the FSS (Figure 4.11). Pyrite content for the O a l horizon was
83 mg FeSg L ’ at the FSS, which was the lowest. Figure 4.12 presents the
weighted average pyrite content to a 150-cm depth for all of the soil profiles.
The highest pyrite content (>3500 mg FeSg L' ) was observed for the BSS while
the lowest (<1500 mg FeSg L^) was for the stable marshes at the FIL.
Most of the soil profiles indicated the highest pyrite accumulation within
the thin layer of dark organic material that occurred immediately above the Cg
horizon. This was characterized with a strong sulfide smell in the field. Except
for the FSS, FIL, and BIL, this horizon contained more than 5000 mg FeSg L \
Its contribution was not dominant when calculating the weighted average for the
131
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CO CO
oooCO
ooo
ooo(O
oooin
ooo
ooo0 0
oo
ooo
S2(0E
I(D0)
_ C
CO
J5c
CT (0E "—'03c ^ 5 DOcoÜ
•I>>CL
<U*< /)
E
IJ
Q .
s"C>.CL
05•cf23O)
UOZUOH NOS
132
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
1
ooooo
ooo
oooco
oooin
oo§
oooco
oooCN
ooo
S I2CDE
IEa
0)
■Dcjgc
O) *o& sc W B Wc C3-o I•■§ E> , CD û. 0)
B1Q .
B'C>.a.
"4"E3O)
CDoCMCDo
coCDo o
lOCDo
U O ZUO H n o s
133
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
(/) , (/)L L U _
m □
oOO00
OOON
OOOCO
OOOin
ooo
oooCO
oooCNJ
ooo
JZ£2
E
Im
T JcJO^ .5
"gD ) (13
WCO
0;g'inEs
cBcoO
Û-
i1Q .
B'=>.D.
E3.25u_
COO
<N(0O
COCDo o
UO ZUO H n o s
134
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD■ D
OQ .C
gQ .
■DCD
C/)C/)
8
( O '
3.3 "CD
CD■DOQ .C
ao3"Oo
CDQ .
■DCD
WÜ1
2 FSS
o BSS
0 1000 2000 3000 4000 5000
Pyrite concentration (mg L'^)
Figure 4.12. Weighted average of pyrite content for the soil profile to a depth of 150 cm.
C /)C /)
profile because of its thickness. The mechanism of this concentration of pyrite
was not clear. However, several hypotheses on its formation can be
developed. This may be formed under highly saline condition with high S and
labile C supply at the initial stage of marsh formation. It may represent bottom
sediments of a lake at that time, which was developed into a marsh later. This
could be the more logical way of formation of this soil layer. Another
hypothesis is the pyrite preferably formed adjacent to the mineral layer because
of high Fe availability. Dissolved organic compounds moved through the pore
water with reduced S and Fe to the bottom of the organic layer and then formed
pyrite. Pyrite formed within the organic layer where more labile carbon may be
present, and eventually moved to the bottom and accumulated at the top of the
mineral layer because the vertical movement was confined. Another hypothesis
is a moving delta with seawater and vegetation that grew for a certain time
period. During that time pyrite accumulated highly within the root zone with
favorably reduced conditions and availability of soluble carbon. With time, the
area would have been isolated from the sea, marsh grew up without much
pyrite formation. However, these scenarios need to be investigated.
4.4.4 Non-pyritic Fe
The HCI digestion during the indirect pyrite determination technique
extracted non-pyritic Fe and S from the soil samples (Schnider and Schnider,
1990). The non-pyritic Fe and S profiles are presented in this section.
Figures 4 .13 through 4.16 present the non-pyritic Fe profiles for the
different sites. The non-pyritic Fe content for the SSS ranged from 1055 to
136
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CO CO CO CO 0 □
1
T
oooCO
oooCO
ooo
oooCM
oooo
ooo0 0
oooCO
ooo■M-
oooCM
nmE0).5V)m
JZ
CO
-D
I
Î Îl ï - gÜ M
o
Co
CO
23.5)LL
COO
%O
COCOO O
%O ü
uozuoH NOS
137
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD■ D
OQ.C
gQ.
■DCD
C/)C/)
8■D
3.3 "CD
CD■DOQ.C
aO3"OO
CDQ.
0 a 1
Oa2
g Oa3goX
w Oa4
CO00
Oa5
cg
BBSS
;ÜBIL
2000 4000 6000 8000 10000 12000 14000 16000 18000
T3(D
(/)(/)
Non-pyritic Fe (mg L'^)
Figure 4.14. Non-pyritic Fe profiles for streamside (BSS) and inland (BIL) for the brackishmarsh.
CD■ D
OQ.C
gQ.
■DCD
C/)C/)
8■D
3.3 "CD
CD■DOQ.C
aO3"OO
CDQ.
0 a 1
Oa2
c
I° O a 3
6W
wCO
Oa4
Oa5
EOISS
0 2000 4000 6000 8000 10000 12000 14000 16000 18000
■DCD
C /)C /)
Non-pyritic Fe (mg L )Figure 4.15. Non-pyritic Fe profiles for streamside (ISS) and inland (IIL) for the intermediate
marsh.
% =d u. u_m □
oooCO
oooCD
ooo
oooCM
OOoo
oooCO
oooCO
ooo
oooCM
£2COE
I<DJC.
TDcm
-ac
i lCD
o E
II1CL<D
co
CD
2305
CDoCM(0o
CO
oO)Ü
U O ZUO H I P S
140
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
8006 mg Fe L ’ within the organic layer compared to 2076 to 8717 mg Fe L ’ for
the SIL. Higher Non-pyritic Fe content at SSS OaS and SIL Oa4 are similar
and also suggests that they represent one subhorizon that was formed with
high Fe supply. This may be formed when the Mississippi River supplied more
sediment to this area. This may also help for high pyrite accumulation within
this subhorizon. Non-pyritic Fe content for the mineral layers (more than 15000
mg Fe L' ) were higher than that of the organic layers at both landscape
positions due to high mineral matter within the Cg horizon. Non-pyritic Fe
profiles followed a similar pattern for the BSS and BIL. However, lower non-
pyritic Fe content was found for the IIL compared to the ISS. For FSS, the non-
pyritic Fe content within the organic layer varied from 1528 to 1722 mg Fe L
as compared to 1764 to 2272 mg Fe L' for the FIL. The variation within the
profiles was very similar for the fresh marsh (Figure 4.16). Figure 4 .17
presents the weighted average non-pyritic Fe contents. For the intermediate
marsh, the weighted averages were very low compared to other sites because
the profiles at ISS and IIL did not contain a Cg horizon within 150 cm. The non-
pyritic Fe content of the Cg horizons is very high because of the high mineral
matter within the Cg horizon.
Statistical analysis indicated that the non-pyritic Fe content was
significantly different between the landscape positions within the marsh types;
differences were detected between SSS and SIL (p=0.0005) and BSS and BIL
(p=0.036). For both marsh types, the streamside samples contained higher
mean non-pyritc Fe content (saline marsh, 4401 vs. 2543 mg Fe L \ brackish
141
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD■ D
OQ .C
gQ .
■DCD
C/)C/)
8■D
CD
3.3 "CD
CD■DOQ .C
ao3T3O
(DQ .
M
FIL
FSS0)w•g IIL m
I ISS■(/)o°- BIL0)Q .
8(0
C
BSS
SIL
SSS
2000 3000 4000 50000 1000 6000
T3(D
-1,Non-pyritic Fe (mg L )
Figure 4.17. Weighted average non-pyritic Fe for the soil profile to a depth of 150 cm.
C /)C /)
marsh, 3630 vs. 2653 mg Fe L' ). This suggests that the inland area may be
suffering from lack of sedimentation or higher sub-surface erosion. This may
be the reason that the O a l horizon in SIL contained less pyrite compared to the
SSS (see section 4.4.3). Haering et al. (1989) also found that pyrite
accumulation was favored for streamside profiles that received Fe inputs from
tidal flushing.
Non-pyritic Fe content for the Oa2 horizon was significantly different
between marsh types; intermediate marsh was significantly different from the
other marshes and was the lowest among them. This may be due to the
disintegration and erosion of material within the intermediate marsh profiles.
The Fe within the Oa2 horizon may be diffused down to the lower horizons of
ISS and IIL, where highest pyrite contents were observed within the Oa3
horizons (see section 4.4.3). This also suggests that lower non-pyritic Fe
content can be a good indicator for a degrading organic soil horizon.
The fresh marsh had the lowest non-pyritic Fe content within the Cg
horizon and was significantly different from all other marsh types. The
weighted mean non-pyritic Fe content was significantly different between marsh
types (p=0.007), as was the landscape positions within the sites (p=0.009).
The lowest mean was measured for the intermediate marsh because the
profiles at ISS and IIL did not contain a Cg horizon. Means for all the marsh
types were significantly different from each other. Landscape position effect
was non-significant for the intermediate marsh, which was extensively broken-
up (less than 50% vegetation cover). Other sites indicated significant
143
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
differences between landscape positions; inland contained higher amounts
than the streamside for the saline and fresh marshes, but it was reverse for the
brackish marsh. The depth to mineral layer (DML) is similar at both landscape
positions at saline and fresh marshes, therefore, the main differences can be
contributed to organic layers. The higher non-pyritic Fe content within the
organic layers of inland may indicate less pyritization that was not due to lack of
Fe. This may be due to inhibition of pyrite formation or promoted pyrite
oxidation as discussed in section 4.4.3. The DML of the BSS was shallow
hence the Cg horizon was thicker. The non-pyritic Fe content within mineral
horizons was very high. Non-pyritic Fe at BIL may have flushed away through
the small streams that run through the inland marsh. This may be another
reason for low non-pyritic Fe at BIL. Therefore, the non-pyritic Fe content was
lower for the profile at BIL.
4.4.5 Non-pyritic 5
Figure 4 .18 presents the variation in non-pyritic S within the profiles for
the saline marsh. The SSS had higher non-pyritic S for all subhorizons and the
quantity ranged from 842 to 1090 mg S L' ) compared to the SIL, which ranged
from 695 to 950 mg S L '\
The non-pyritic S content for the BSS ranged from 389 to 956 mg S L
and ranged from 584 to 1037 mg S L' for the BIL. The surface organic layers
contained higher values at both landscape positions (Figures 4.19). Profile
variation of non-pyritic S content for the intermediate marsh is presented in
Figure 4.20 in which the Cg horizon was below 150 cm. Non-pyritic S contents
144
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
œ (/)
ooCM
ooo
OO00
ooCD
O)
CO
S:o
Z
oo
ooCN
JCÿ.mE0)ç"râ</)03sz
•oc_ç5ç
■ocro
COCOw(D■g(/)I0
Q .
COü
Ècoz00
23.g)u_
UOZUOH NOS
145
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CO COm □
ooCM
OOO
OOCO
ECO
CO
a>
CO
•OcCO
T3cCO
CO
OOCO
COa
co
oo
<D COE
I"co
1 Q .
CO a
à :
ÉzCJ>
■M"23
L i.
(0O
CM(0O
COCOO O
U5COo
O)Ü
UOZUOH NOS
146
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
ooo
oooo
ooCD
oo"4"
OOcg
I■si
I<D
-C
T3c
£
clIICO q)u :g•ti CO
1 1o CO
x:£2(0E
1CL
COü
&cozCDCN
■cf230 5
UOZUOH nos
147
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
were similar within the organic layer and ranged from approximately 500 to
1000 mg S for both ISS and IIL
For the fresh marsh, non-pyritic S content was almost half that of the
other sites and ranged between 300 and 600 mg S L^ (Figure 4.21).
The weighted average S content for each landscape position is presented in
Figure 4.22.
Non-pyritic S content in the O a l horizon was significantly different
between the marsh types. This may be mainly due to the S supply variation
that can be associated with salinity and seawater intrusion. The fresh marsh
had the lowest mean of 439 mg S L ’ for the O a l horizon and was significantly
different from the means of the other sites, which are more than twice that of
the fresh marsh. Landscape position effect was not found to be significant for
the O a l horizon. The SIL may be frequently flooded and receives 8 from the S
enriched water or else 8 forms recycle within the O a l horizon from the
frequently oxidizable surface layer (Lord and Church, 1983). Both marsh type
(p=0.018) and the landscape position (p=0.036) had a significant influence on
the non-pyritic 8 content in the Oa2 horizon. Intermediate and fresh marshes
were significantly different from other marshes. Lower non-pyritic 8 contents at
less saline areas can be attributed to low 8 supply, especially in the fresh
marsh. For the intermediate marsh, sulfate reduction may continue to form
pyrite, which resulted in lower non-pyritic 8 . A higher pyrite content was
determined for the brackish marsh. The BIL was significantly different from the
148
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
ooCM
wWu_
I i
ooo
jC2(0E
m0)
oooo
TooCO
_L
t O .
êCOü
è :É
oo■M-
T3C_rac
X3Cm
COCO
m;g
I
Io5
Q .(/)ü
OOCM
co
CM
23O)
mO
%O
COmO
enü
U O ZU O H NOS
149
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
ooCM
OOO
Oo0 0
ooCD
ooM-
OoCM
9 %S pue uoi^isod adeospuB"!
Ig
0
t0)■Dm3
ex
6i/>d)
J Z
II^ 2 0) ^ D)
1T3ÆJZro0)
CMCMM"e3.g)U L
150
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
BSS (p=0.03). This can be a result of limited pyritization at BIL that contained
lower non-pyritic Fe compared to BSS.
Intermediate and fresh marshes had significantly lower non-pyritic S
contents within the Oa3 horizons compared to other marshes; fresh marsh had
the lowest mean (470 mg S L ’). Mean for the non-pyritic S content for the Cg
horizon for the fresh marsh, was the lowest among marsh types (324 mg S L' ).
Lower horizons indicate pronounced differences of S supply into the less saline
areas. Weighted mean averages of non-pyritic S for the profile indicated
significant differences between marsh types (p=0.03) and the landscape
positions (p=0.01). The fresh marsh had the lowest mean (441 mg S L' ) while
the other marsh types had about twice that amount (saline, 903; brackish, 824;
intermediate, 730 mg S L ’). The landscape positions were significantly
different for the saline and brackish marshes. The SSS had higher amount of
non-pyritic S than the SIL, but this trend was reversed for the brackish marsh.
Differences between the marsh types may be attributed to less S supply, high S
consumption by the plants and the sulfate reduction. Landscape position
differences existed at the more saline areas. Streamside may contain more S
compared to inland when the inland is landlocked. However, when a stream
breaks the hydrological barriers, non-pyritic S may be accumulated within
inland profiles due to limited pyritization.
4.4.6 Soil pH
Variations in soil pH for different marsh profiles are presented in Figure
4.23 for the streamside and Figure 4 .24 for the inland. Differences between
151
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CO CO CO CO CO 00 u_
CJ
inmO
O
IoX
oCO
COmO
CMmO
Q.
«iTO
* 0(U•gTOE
I«£
Q.a.CD
COCM■M"23.gU_
TOO
O) 00 CO in CO CM
Hd
152
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
ü
"%o
CO(0O
O)
c/3 CQ =□ EU m DD
%O
njO
CO in CO CM
C
Io
X
■ 5CO
oQ.
x:E2(0Em'o•Scroc
1Q.XQ.0)iS
2 3 O)
Hd
153
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
marsh types were more pronounced than differences between the landscape
positions. The pH ranges for the soil profiles were as follows; for SSS and SIL,
5.98 to 7.5; for BSS and BIL, 5.44 to 8.17; for ISS and IIL, 4 .29 to 5.71; for FSS
and FIL, 4 .32 to 6.73. The Cg horizon always had the higher pH. Note that
ISS and IIL did not have a Cg horizon within a depth of 150 cm.
There were statistically significant soil pH differences between marsh
types (p=0.04) and landscape position within marshes (p=0.04) for the Oa1
horizon. The O a l horizon of intermediate and fresh marshes was acid and
significantly different from the more saline marshes. The ISS pH (4.29) was
significantly lower than IIL pH (5.13), showing landscape position differences
only for the intermediate mash. Mean pH of the Qa2 horizon was the lowest for
the fresh marsh (4.41 ) and highest for the saline marsh (6.65). The differences
between marsh types were highly significant for the pH of the Ga2 horizon.
The pH of the Ga3 horizon ranged between 4.86 and 6 . 6 6 among marshes and
the more saline marshes had higher pH. This may be the influence of salinity.
Except for the brackish and intermediate marshes the Ga3 horizon pH was
significantly different between marshes. The pH of the Cg horizons was
significantly different between marshes; brackish marsh had the highest pH of
8.15.
4.4.7 Microanalysis of Soils for Pyrite
Information on clay mineralogy and other associated minerals for coastal
marsh soils indicate the prominent pedogenic processes within the marsh
ecosystem. Coastal marsh environments favor pyrite formation. Pyrite crystals
154
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
occur in the form of framboids or clusters of single crystals. Framboidal pyrite
forms when Fe monosulfides react with elemental S. Other crystal forms of
pyrite may be formed as a result of polysulfide oxidation. The observations
from XRD and SEM are presented in this section as evidence for pyrite within
these soils. Pyrite framboids were detected within salt marsh sediments.
Figure 4 .25 presents a micrograph showing the microstructure of the organic
sediments. This indicates the micropores and the surface area within the
sediments. Pyrite was detected within the salt marsh sediments as framboids
(spherical aggregates of microcrystals) and clusters of single crystals. Pyrite
framboids were associated with decaying organic material (Figure 4.26). White
arrows indicate the framboids. The framboids are about 8 pm in diameter, and
some of them have disintegrated into single crystals. An enlargement of the
clusters of pyrite crystals is presented in Figure 4.27 and a highly magnified
pyrite framboid is shown in Figure 4.28, which has a diameter of about 6 pm.
The X-ray diffractograms (ZRD) data are presented for air-dried versus
treated smears from the Oa1 horizon to identify pyrite and clay minerals.
Figure 4 .29 presents the XRDs for the < 2 pm fraction from the saline marsh
sediments, while Figure 4.30 presents the < 20 pm fraction. Smectite, illite and
kaolinite peaks were easily detectable for the < 2 pm fraction. For the 20 pm
fraction, quartz peaks are dominant and clay peaks were weak but higher
intensity was observed for the pyrite peaks. The primary peak for pyrite occurs
155
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
m
1 12 (0
1*o2
%
CO
2ü
O )c
î-CCO
Q .2O)20Ec
11O)c
’ccswiriCM
2 3g)
UL
156
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD■ D
OQ .C
gQ .
■DCD
C/)C/)
8■D
CD
3.3 "CD
CD■DOQ .C
aO3"OO
CDQ .
■DCD
C /)C /)
en
Figure 4.26. Scanning electron micrograph showing pyrite framboids within organic material of saline marsh sediments from the 0a1 horizon. P = Pyrite framboids.
158
IoJZ
(0oa>£EP
SE
1IroEmç
1
(/>■o0SiE
•I' 6CL
1ü
23O)
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
c
§
CQO0)£EP
c0 )EisCO
fCOE(U_çlôCO
•gEE2
Ià_0)gCO
00CNj
23D )
159
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD■ D
OQ .C
gQ .
■DCD
C/)C/)
8■D( O '
3.3"CD
CD■DOQ .Cao3
T3O
CDQ .
O)o
5000
S=Smectitel=llliteK=KaoliniteQ=Quartz
550 C4000
300 °C3000
C
c2000
EG (Ethylene Glycoiated)
1 0 0 0 i
Air dried
4020 30 50 60100
"OCD
(/)(/)
20
Figure 4.29 The XRD patterns of saline marsh sediments (<2 pm) from the Oal horizon.
CD■oOQ .cgQ .
■oCD
C/Î
o'3
3CD
C3.3 "CD
CD■oOQ .CaO3
■oO
&
oc■oCD
C/5
o'3
2500
2000 ^
O)
(/)cI
1 550 °C Q
1500
1000
500 ^
Q300 X
S IK
S=SmectiteNllliteK=KaoliniteQ=QuartzP=Pyrite
Ethylene Glycoiated
Air dried
10 20 30
2 0
40 50 60
Figure 4.30 The XRD patterns of saline marsh sediments (<20 pm) from the Oal horizon.
at 28° 20, and the other orders occur at 33, 36.5 and 40.3° 20. The X R D ’s for
the brackish marsh sediments are presented in Figure 4.31 (< 2pm) and in
Figure 4 .32 (< 20 pm). Pyrite peaks also were detected from the brackish
marsh sediments. The XRD patterns indicated similar clay mineralogy in the
surface horizon (O a l horizon) of brackish and saline marshes. The XRD data
from both saline and brackish marshes indicated more pyrite within the less
than 20pm size fraction as compared to the < 2pm fraction. Figure 4.33
presents differential XRD pattern of <20pm fraction between saline and
brackish marsh types and between the 2 and 2 0 pm fractions for saline and
brackish marsh types. The main difference between the size fractions was the
higher quartz and pyrite peaks for the <20 pm fraction. The differences
between the saline and brackish marsh < 2 0 pm, indicates higher peaks for
clays and quartz within saline marsh sediments. These data provide
mineralogical evidence for pyrite accumulation within the salt and brackish
marsh sediments.
4.4.8 Soil Classification
There is a considerable amount of 8 containing compounds
accumulated within the soil profile. They occur as pyrite or other reduced 8
forms, in addition to the organic 8 fractions and the sulfates from the seawater.
Most of these compounds are found within the surface or subsurface tire of the
control section of the soil profile. Based on this information, and considering
the need to indicate the possible environmental impact on using these lands, it
162
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD■ D
OÛ .C
gQ.
"DCD
C/)C/)
3000
(D
8
33 "CD
CD■DOQ.C
aO3"OO
CDQ.
■DCD
C/)(/)
O)Ca)
2500
2000
s 1500
1000
500
550 C
S=Smectitel=illiteK=KaoliniteQ=Quartz
300 C
Ethylene Glycoiated
Air dried
I I l _____
10 20 30
20
40 50 60
Figure 4. 31 The XRD patterns of brackish marsh sediments (<2 pm) from the Oal horizon.
CD"D
OQ.C
gQ.
■DCD
C/)C/)
CD
8■D( O '
3.3"CD
CD■DOQ.C
aO3"OO
CDQ.
■DCD
(/)(/)
2000
1600
^ 1200 Bc0)
400
Q
550 C
300 XQ
S I
S=Smectitel=llliteK=KaoliniteQ=QuartzP=Pyrite
EG
Air dried
0 5 10 15 20 25 30 35 40 45 5020
Figure 4.32 The XRD patterns of brackish marsh sediments (<20 mm) from the Oal horizon.
CD■DOQ.C
gQ.
■DCD
C/)C/)
8
ci'
33 "CD
CD■DOQ.C
aO3"OO
CDQ.
■DCD
O)CJI
(/)c0)
cgê
1900
1400
900
400
-100
-600
Q
Saline - Brackish (<20 pm) 'V wiWwHWK'if#*"
I Brackish Marsh
Saline Marsh
10 20 30
20
40 50
S=Smectitei=j|liteK=KaoliniteQ=QuartzP=Pyrite
60
Figure 4.33 Differential XRD patterns between 2 and 20 pm fractions fromthe Oal horizons at saline and brackish marshes.
C/)C/)
is suggested that the sulfuric or sufidic horizons need to be designated within
these soils. The technique used in this study to estimate pyrite content also
provides non-pyritic S content, while the pyritic S content can be estimated from
the pyrite estimates (Schneider and Schneider, 1990). This method has the
potential to be used in soil characterization, especially to identify sulfidic
material (pyritic and non-pyritic S). Otherwise, new differentiae need to be
introduced to classify these soils to imply the potential problem for the use and
m anagement of these soils. A symbol may be introduced to identify pyrite
accumulation, similar to “j” that designates jarosite accumulation (Soil Survey
Staff, 1996). Designation of pyrite accumulating horizon also will be useful in
the development of a scheme for classifying pond soils for aquaculture (Boyd,
1995).
4.5 Summary and Future Research Needs
Organic layers comprise distinct subhorizons within the soil profiles. The
number of subhorizons varies within the landscape and between marsh types.
A thin layer of dark organic material occurs immediately above the mineral layer
with a strong sulfide smell within most of the soil profiles. These organic soils
develop from bottom to up mainly by the organic and inorganic accretions that
will counter local subsidence. Accretions are higher at the SS than the IL,
therefore, a higher number of subhorizons may be found at SS compared to IL.
Eventually contemporary soil layers occur at the bottom of the profiles but not
at the surface between the landscape positions. Therefore the subhorizons
166
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
that have the same horizon designation may or may not be contemporary, and
this can be a major source of spatial variability within the marsh.
Thickness of the Oa1 and Oa3 horizons is statistically different between
the landscape positions within the intermediate marsh. Incorporation of two
adjacent subhorizons into one subhorizon may occur within a degrading marsh.
The spatial variability of the 0a1 horizon between SS and IL can be an
indicator of the marsh stability at a particular location. Erosion and re
deposition of organic soil material may create wide spatial variability within a
degrading marsh. If the landscape pattern of the variability is identified, the
mechanisms of marsh loss within an area can be revealed. The degrading Oa1
horizon can release mineral material for subsurface horizons while losing its
integrity. Peat collapse may promote consolidation and compaction within the
subsurface horizons because water pressure can be extended deeper into the
profile when flooded. Thickness of the Oa2 horizon at the intermediate marsh
is significantiy different from the other marshes. Therefore, information on the
other organic subhorizons is required to support the data from the 0 a 1 horizon.
The DML equals to the total organic layer thickness unless the marsh surface is
under standing water. Variations in DML can be due to the depositional
variations when the mineral layer was formed. Depressions formed at that time
may have received more accretions and formed marshes with deeper DML.
When marsh degrades these depressions may be more vulnerable and can
form the open water patches within the marsh. The relationship between
occurrence of hotspots and micro relief variations within the degrading marshes
167
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
needs to be further studied to test this hypothesis. However, the variations in
number of organic subhorizons, and thickness of any subhorizon are indicative
of higher spatial variability within a marsh.
Soil BD was lower for the brackish marsh compared to the saline marsh.
Lack of sediment accumulation into the brackish marsh areas may be the
reason for lower BD. The BD varied highly within the organic layer of the
brackish marsh while it was uniform for the saline marsh. Salinity can increase
sedimentation due to enhanced flocculation.
Salinity for all the subhorizons was significantly different between marsh
types indicating that the sites have well represented different levels of salinity.
Salinity profiles differed between landscape positions when the inland area was
land-locked. This difference may be pronounced in more saline areas.
Evapotranspiration and lack of lateral flow (hydrological barriers) may change
salinity profiles going inland from the streamside. When small streams flow
through the marsh, the hydrological barriers are broken and salinity differences
disappear. Biogeochemical differences may result due to this salinity variation
within the landscape. Therefore, understanding the spatial variability of salinity
is important when monitoring the marsh status within an area.
Salinity influenced pyrite accumulation; however, its influence varied
within the profile. Pyrite content within the Oa1 horizon was significantly
different between landscape positions. There was no evidence of differences
between marsh types because the balance between pyrite formation and
oxidation mainly controls pyrite content within the 0a1 horizon. Pyrite content
168
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
within the surface organic layers for the inland position was lower compared to
the streamside, especially when the inland is landlocked. The mechanism of
oxygen transport plant to the roots combined with leakage of oxygen into
rhizosphere may be insufficient to oxidize pyrite. The soil aeration due to plant
water uptake can create prolonged oxidized status within the surface soils or
frequent fluctuation of redox status. It is not clear which mechanism is more
significant in pyrite oxidation. For subsurface organic horizons, the landscape
position effect on pyrite accumulation dramatically diminished but the marsh
type effect was prominent. This can be a long-term salinity effect on pyrite
accumulation within the marshes. The higher the marsh salinity, the greater the
pyrite accumulation within the profile. The highest pyrite accumulation was
observed within the thin layer of dark organic material that occurred
immediately above the mineral layer.
The mechanism of formation of the highly pyritic soil layer is not clear.
The most possible scenario is that this soil layer was formed from lake bottom
sediments under high saline condition with enriched supply of labile C and Fe,
later overlain by the organic accretions forming the surface layers. The other
hypotheses is that the pyrite preferably forms top of the mineral layer because
of high Fe availability. Otherwise the dissolved organic compounds can move
through pore water with reduced S and Fe to the bottom of organic layer and
then forms pyrite. Pyrite may form within the organic layer where more labile
carbon is present, and eventually moves to the bottom and accumulates at the
top of the mineral layer where the vertical movement is confined. The
169
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
hypothesis on movement of organic material can be proven if the underlain
material has a younger age than the overlying organic materials, this is the
test for Humilluvic material within organic soils (Soil Survey Staff, 1996).
Another possibility is a moving delta that grew for a certain time period resulted
in pyrite accumulation within the root zone; later, the area would have been
isolated from the sea resulting in less pyrite accumulation.
Non-pyritic Fe contents are significantly different between the landscape
positions within the more saline marshes (i.e., saline and brackish marshes).
This suggests that the inland areas may be suffering from either lack of
sedimentation if landlocked or subsurface erosion otherwise. Downward
movement through the profile can be another reason, which supports one of
the hypotheses of pyrite concentration within the bottom organic subhorizon.
The soil profiles at ISS and ML had an Oa3 horizon, which contained more
pyrite and underlain the Oa2 horizon with lower non-pyritic Fe and pyrite
contents. This supports the vertical downward movement of Fe compounds
within the profile, as well as, the isolation of an actively growing deltaic marsh.
These results suggest that studying different subhorizons within the profile
(“pedological approach”) can reveal more information than studying only the
surface layer in biogeochemical studies. The intermediate marsh contained
significantly lower non-pyritic Fe within surface organic layers compared to
other marshes. This may be related to the status of the marsh because the
intermediate marsh at this location is extensively broken-up (less than 50%
170
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
vegetation cover). The non-pyritic Fe content can be a suitable indicator to
assess marsh status. When it is land-locked, the inland position can retain
more non-pyritic Fe within subsurface organic layers due to limited pyritization
(i.e., saline marsh). The non-pyritic Fe can be flushed away when no
hydrological barriers occur between landscape positions.
Non-pyritic S content within the organic sub horizons differs significantly
between marshes due to the salinity changes. As salinity increases from
brackish to saline marsh, the content of non-pyritic S increases. Less saline
marshes are S limited. Unlike the 0a1 horizon, landscape position showed a
significant difference for non-pyritic S within the Oa2 horizon, especially for the
brackish marsh. The BIL contained more non-pyritic S within the profile than
the profile at the BSS. This suggests that when the inland is not land-locked,
non-pyritic S accumulate within the profile. Subsurface organic horizons within
the profiles of less saline areas indicate very limited 8 supply.
Soil pH differences are more pronounced between marshes than the
landscape positions. The pH did not vary significantly within the organic layer.
The mineral layer always has higher pH compared to the organic subhorizons.
The pH of the 0a1 horizon differed significantly between less saline marshes
and more saline marshes. Landscape difference was found only at the
intermediate marsh where marsh was extensively degrading. The ISS soil
profile was more acid than the IIL. The pH of the mineral layers of less saline
marshes was significantly lower compared to the saline marshes.
171
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
The pyrite and non-pyritic Fe and S data for the soil profiles can be
utilized in making decisions on marsh health and marsh management
strategies. The conditions can be spatially variable within the marsh, therefore,
they need to be evaluated separately. For example the condition of the soil
profiles at the BIL can be considered. The BIL and BSS did not differ in their
salinity, and evidently the BIL was not landlocked. The BIL indicated
accumulation of non-pyritic S within the profile. Low pyrite accumulation may
be due to low non-pyritic Fe. The marsh looked vulnerable and had small
hotspots. This may be due to sulfide toxicity. Improvement of sediment supply
may be one scenario to manage this marsh, which will assure Fe supply.
Pyrite framboids were detected within the saline marsh sediments using
SEM. The framboids were about 6 to 8 pm in diameter and were found in close
association with organic material. The sediments at both saline and brackish
marshes contained mixed silicate mineralogy with smectite, illite, and kaolinite
clays. Pyrite was evident within the sediments at both saline and brackish
marsh types; the coarser fraction ( < 2 0 pm) contains more pyrite.
There is a considerable amount of reduced S compounds accumulated
within these soil profiles, which occurs as pyritic and non-pyritic S. These
organic soils should be reclassified to indicate sulfidic materials within their
profiles. The technique used to estimate pyrite and non-pyritic S can be
adopted as a method to characterize sulfidic material within these soils.
172
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
4.6 ReferencesBaas Becking, L. G. M., and D. Moore. 1961. Biogenic sulfides. Econ. Geol.
56:227-259.
Begheijn, L. Th., N. van Breemen, and E. J. Velthorst. 1978. Analysis of sulfur compounds in acid sulfate soils and other recent marine soils. Commun. Soil Sci. Plant Anal. 9(9):873-882.
Berner, R. A. 1964. Distribution and diagenesis of sulfur in some sediments from the Gulf of California. Marine Geol. 1:117-140.
Bohn, H. L., F. Young, and H. Chenghe. 1989. Hydrogen sulfide sorption by soils. Soil Sci. Soc. Am. J. 53:1914-1917.
Boyd, C. E. 1995. Bottom soils, sediment and pond aquaculture. Chapman and Hall, New York. 10-66pp.
Bradley, P. M., and J. T. Morris. 1991. Relative importance of ion exclusion, secretion and accumulation in Spartina alterniflora Loisel.. J. Expt. Bot. 42:1525-1532.
Broome, S. W., I. A. Mendelssohn, and K. L. McKee. 1995. Relative growth of Spartina pa tens (Ait.) Muhl. and Scirpus o iney i Gray occurring in a mixed stand as affected by salinity and flooding depth. Wetlands 15:20-30.
Carlson, Jr., P. R., and J. Forrest. 1982. Uptake of dissolved sulfide bySpartina altern iflora: Evidence from natural sulfur isotope abundance ratios. Science 216:633-635.
Chmura, G. L., R. Costanza, and E. C. Kosters. 1992. Modelling coastal marsh stability in response to sea level rise: a case study in coastal Louisiana, USA, Ecological Modelling, 64:47-64.
Connell, W . E., and W. H. Patrick, Jr. 1969. Reduction of sulfate to sulfide in waterlogged soil. Soil Sci. Soc. Am. Proc. 33:711-715.
Coultas, C. L. 1997. Soils. In C. L. Coultas and Y. Hsieh (Eds.) Ecology and Management of tidal marshes: A model from the Gulf of Mexico. St.Lucie Press, Delray Beach, Florida. 53-75pp.
Crozier, C. R., I. Devai, and R. D. DeLaune. 1995. Methane and reduced sulfur gas production by fresh and dried wetland soils. Soil Sci. Soc. Am. J. 59:277-284.
173
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Dacey, J. W. H., and B. L. Howes. 1984. W ater uptake by roots controls water table movement and sediment oxidation in short Spartina marsh.Science 224: 487-489.
Day, J. H., P. J. Rennie, W . Stanek, and G. P. Raymond. 1979. Peat testing manual. Technical Memorandum No. 125, Associate Comm, on Geotechnical Res., National Research Council, Ottawa, Canada.
DeLaune, R. D., C. J. Smith., and W. H. Patrick. 1983. Relationship of marsh elevation, redox potential, and sulfide to Spartina alterniflora productivity. Soil Sci. Soc. Am. J. 47:930-935.
DeLaune, R. D., J. A. Nyman, and W. H. Patrick, Jr. 1994. Peat collapse, ponding and wetland loss in a rapidly submerging coastal marsh. J. Coastal Res. 10:1021-1030.
DeLaune, R. D., S. R. Pezeshki, and W. H. Patrick Jr. 1993. Response of coastal vegetation to flooding and salinity: A case study in the rapidly subsiding mississippi river deltaic plain, USA. In M. B. Jackson and C. R. Black (Eds.) Interacting stresses on plants in a changing climate,(NATO ASI Ser. Vol. 116), 211-229pp.
Dent, D. 1993. Bottom-up and top-down development of acid sulphate soils. Catena 20:419-425.
Fanning, D. S. 1993. Salinity problems in acid sulfate coastal soils. In H. Lieth and A. AI Masoom (Eds.) Towards the rational use of high salinity tolerant plants. Vol.1:491-500.
Fanning, D. S., and M. C. B. Fanning. 1989. Soil morphology, genesis, and classification, John Wiley & Sons. New York, New York. 69-80p.
Feijtel, T. C., R. D. Delaune, and W. H. Patrick, JR. 1988. Seasonal pore water dynamics in marshes of Barataria Basin, Louisiana, Soil Sci. Soc. Am. J. 52:59-67.
Freney, J. R., G. E. Melville, and C. H. Williams. 1970. The determination of carbon bonded sulfur in soil. Soil Sci., 109:310-318.
Gaillard, J., H. Pauwels., and G. Michard. 1989. Chemical diagenesis in coastal marine sediments. Oceanologica Acta 12:175-187.
Giblin, A. E., and R. W. Howarth. 1984. Poreater evidence for a synamic sedimentary iron cycle in salt marshes. Limnol. Oceanogr. 29:47-63.
174
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Goldhaber, M. B., and I. R. Kaplan. 1982. Controls and consequences ofsulfate reduction rates in recent marine sediments, In J. A. Kittrick, D. S. Fanning, and L. R. Hossner (Eds.) Acid sulfate weathering. Soil Sci. Soc. Am.Spec. Pub. No. 10, Soil Sci. Soc. Am., Madison, Wisconsin. 19-36p.
Griffin, T. M., and M. 0 . Rabenhorst. 1989. Processes and rates ofpedogenesis in some Maryland tidal marsh soils. Soil Sci. Soc. Am. J. 52:59-67.
Haering, K. 0 ., M. 0 . Rabenhorst, and D. S. Fanning. 1989. Sulfur spéciation in some Chesapeake Bay tidal marsh soils. Soil Sci. Soc. Am. J. 53:500- 505.
Howarth R. W ., and S. Merkel. 1984. Pyrite formation and the measurement of sulfate reduction in salt marsh sediments. Limnol. Oceanogr., 29:598- 608.
Kosters, E. C., and A. Bailey. 1983. Characteristics of peat deposits in the Mississippi river delta plain. Transactions Gulf Coast Association of Geological Societies Vol. XXX III:311-325.
Kostka, J. E., and G. W. Luther III. 1994. Partitioning and spéciation of solid phase iron in salt marsh sediments. Geochim. Cosmochim. Acta 58:1701-1710.
Krairapanond, N., R. D. DeLaune, and W. H. Patrick, JR. 1991a. Sulfur dynamics in Louisiana coastal freshwater marsh soils. Soil Sci. 151(4):261-273.
Krairapanond, N., R. D. DeLaune, and W . H. Patrick, JR. 1991b. Seasonal distribution of sulfur fractions in Louisiana salt marsh soils. Estuaries 14:17-28.
Krairapanond, N., R. D. DeLaune, and W. H. Patrick, JR. 1992. Distribution of organic and reduced sulfur forms in marsh soils of coastal Louisiana,Org. Geochem. 18:489-500.
Latham, P. J., L. G. Pearlstine, and Wiley M. Kitchens. 1994. Speciesassociation changes across a gradient of freshwater, oligohaline, and mesohaline tidal marshes along the lower savannah river. Wetlands. 14(3):174-183.
Leventhal, J., and C. Taylor. 1990. Comparison of methods to determinedegree of pyritization. Geochimica et Cosmochimica Acta 54:2621-2625.
175
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Lin, C., and M. D. Melville. 1994. Acid sulphate soil-landscape relationships in the Pearl River Delta, southern China, Catena, 22:105-120.
Lindsay, W. L. 1979. Chemical equilibria in soils. John Wiley & Sons, New York. 281-298p.
Lord III, C. J. 1982. A selective and precise method for pyrite determination in sedimentary materials. J. Sediment. Petrol., 52:664-666.
Lord III, C. J., and T. M. Church. 1983. The geochemistry of salt marshes:Sedimentary ion diffusion, sulfate reduction, and pyritization. Geochim. Cosmochim. Acta 47:1381-1391.
Moore, D. M., and R. C. Reynolds, Jr. 1989. X-ray diffraction and theidentification and analysis of clay minerals. Oxford University Press,New York.
Munch, J. C., and J. C. G. Ottow. 1980. Preferential reduction of amorphous to crystalline iron oxides by bacterial activity. Soil Sci. 129:15-21.
Nyman, J. A., J. C. Callaway, and R. D. DeLaune. 1993. Case study of arapidly submerging coastal environment: relationships among vertical accretion, carbon cycling, and marsh loss in terrebonne Basin,Louisiana. In P. Bruun (Ed.) Proceedings of the Hilton Head Island South Carolina U.S.A. International Coastal Symposium. 1993, vol. 2:452-457.
Nyman, J. A., M. Carlose, R. D. DeLaune, and W . H. Patrick, Jr. 1994.Erosion rather than plant dieback as the mechanism of marsh loss in an estuarine marsh. Earth Surface Processes and Landforms 19:69-84.
Nyman, J. A., M. Carlose, R. D. DeLaune, and W. H. Patrick, Jr. 1994. Are landscape patterns related to marsh loss processes?. p337-348. In Coastal zone’93, proceedings of 8 th symposium on Coastal and Ocean Management held July 19-23, 1993, New Orleans, Louisiana.
Nyman, J. A., R. H. Chabreck, R. D. DeLaune, and W. H. Patrick, Jr. 1993. Submergence, Salt-water intrusion, and managed Gulf Coast marshes. Coastal Zone’93, p .1690-1704.
Nyman, J. A., and R. D. DeLaune. 1991. Mineral and organic matteraccumulation rates in deltaic coastal marshes and their importance to landscape stability, GCSSEPM Foundation Twelfth Annual Research Conference, Program and Abstracts, December 5, 1991.
176
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Nyman, J. A ., R. D. DeLaune, H. H. Roberts, and W . H. Patrick, Jr. 1993. Relationship between vegetation and soil formation in a rapidly submerging coastal marsh. Mar.Ecol. Prog. Ser. 96:269-279.
Ogata, G., and C. A. Bower. 1965. Significance of biological sulfate reduction in soil salinity. Soil Sci. Soc. Am. Proc. 29:23-25.
Patrick, W. H. Jr., and A. Jugsujinda. 1992. Sequential reduction and oxidation of inorganic Nitrogen, Manganese, and Iron in flooded soil. Soil Sci. Soc. Am. J. 56:1071-1073.
Ponnamperuma, F. N. 1972. The chemistry of submerged soils. Adv. Agron. 24:29-96 .
Pons, L. J. 1973. Outline of the genesis, characteristics, classification andimprovement of acid sulphate soils. In H. Dost (Ed.) Proceedings of first International symposium on Acid sulphate soils. International Land Reclamation Institute, Publication No. 18, Vol I. pp 3-27, Wageningen, The Netherlands.
Pons, L. J., N. van Breemen, and P. M. Driesses. 1982. Physiography ofcoastal sediments and development of potential soil acidity, pp. 1-18. In J. A. Kittrick, D. S. Fanning, and L. R. Hossner (Eds.) Acid sulfate weathering. Soil Sci. Soc. Am. Spec. Pub. No. 10, Soil Sci. Soc. Am., Madison, Wisconsin.
Rabenhorst, M. C., and B. R. James. 1992. Iron sulfidization in tidal marshsoils. In H. C. W. Skinner and R. W. Fitzpatrick (Eds.) Biomineralization processes. Iron, Manganese: modern and ancient environments. Catena supplement 21 :203-217.
Raiswell, R., and D. E. Canfield, and R. A. Berner. 1994. A comparison of iron extraction for determination of degree of pyritisation and the recognition of iron-limited pyrite formation. Chemical Geology 111:101-110.
Raiswell, R., K. Whaler, S. Dean, M. L. Coleman, and D. E. G. Briggs. 1993. A simple three-dimentional model of diffusion-with-precipitation applied to localized pyrite formation in framboids, fossils and detrital iron minerals. Marine Geol., 113:89-100.
Raybould, J. G. 1973. Framboidal pyrite associated with lead-zinc mineralisation in mid-Wales. Lithos 6:175-182.
Rickard, D. T. 1970. The origin of framboids. Lithos 3:269-293.
177
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Rickard, D. T. 1973. Sedimentary iron sulfide formation. pp28-65. In H. Dost (Ed.) Vol I. Acid sulphate soils. International Land Reclamation Institute, Publication No. 18, Wageningen, The Netherlands.
Rickard, D. T. 1975. Kinetics and mechanism of pyrite formation at low temperatures. Amer. J. Sci., 275:636-652.
Rozema, J., E. Luppes, and R. Broekman. 1985. Differential response of salt marsh species to variation of iron and manganese. Vegetatio 62:293- 301.
SAS Institute Inc., 1994. SAS/STAT User’s guide. Version 6 , fourth edition. Volume 2, Cary, NO: SAS Institute Inc., 846pp.
Schneider, J. W., and K. Schneider. 1990. Indirect method for thedetermination of pyrite in clays and shales after selective extraction with acid solutions. Ceramic Bulletin 69(1): 107-109.
Schulze, 1981. Identification of soil iron oxide minerals by differential X-ray diffraction. Soil Sci. Soc. Am. J. 45:437-440.
Sheppard, M. J., C. Tarnocai, and D. H. Thibault. 1993. Sampling organicsoils. In M. R. Carter (Ed.) Soil sampling and methods of analysis. Lewis Publications. 423-439pp.
Soil Conservation Service (SCS). 1984. Soil survey of Lafourche parish,Louisiana. United States Department of Agriculture, Washington, DC.
Soil Conservation Service (SCS). 1989. East Central Barataria cooperative river basin study, Jefferson, Orleans, Plaquemines and St. Charles Parishes, Louisiana. Rev. May 1989. United States. Soil Conservation Service. National Cartographic Center. Ft. Worth, Texas : USDA-SCS-National Cartographic Center ; [Louisiana State Conservationist, distributor].
Soil Survey Staff. 1996. Keys to soil taxonomy. Seventh Edition. United States Department of Agriculture, Washington, District of Columbia.
Thamdrup, B., K. Finster, H. Fossing, J. W. Hansen, and B. K. Jorgensen.1994. Thiosulfate and sulfite distributions in porewaters of marine sediments related to manganese, iron, and sulfur geochemistry. Geochim. Cosmochim. Acta 58:67-73.
Turner, R. E. 1990. Landscape development and coastal wetland losses in the northern Gulf of Mexico. Amer. Zool., 30:89-105.
178
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Welton, J. E. 1984. SEM petrology atlas. The Amer. Assoc. Petrol. Geologists, Tulas, Oklahoma.
Whitcomb J. H., R. D. DeLaune, and W. H. Patrick, Jr. 1989. Chemicaloxidation of sulfide to elemental sulfur; its possible role in marsh energy flow. Marine Chemistry 26:205-214.
Willett, I. R., and T. A. Beech. 1987. Determination of organic carbon in pyritic and acid sulfate soils. Commun, in Soil Sci. Plant Anal. 18(7):715-724.
179
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CHAPTER 5: SPATIAL VARIABILITY OF COASTAL ORGANIC SOIL CHARACTERISTICS WITHIN THE BARATARIA BAY BASIN, LOUISIANA
5.1 Summary and Introduction
Information on spatial variability of coastal organic soils within Barataria
Bay Basin is limited. Understanding the spatial variability of soil characteristics
helps to find the influence of dominant processes on marsh formation. Spatial
autocorrelation was estimated for several coastal organic soil characteristics,
such as, thickness, pH, and organic/mineral ratio (OM R) for soil subhorizons,
depth to mineral layer (DML), and soil subgroups for saline and brackish marsh
types. Each variable was interpolated for a one square mile area to study the
spatial variability.
With the exception of the thickness of the Ga1 horizon within the
brackish marsh, organic horizon thickness showed high spatial autocorrelation.
Variation of horizon thickness was greater at depths within the profile. Contour
plots indicated more accretions at edges of the water bodies. This is mainly
due to higher accretions at streamside than inland within the landscape.
Because of this variation in accretion the Ga1 horizons at streamside may be
younger than the inland G a l horizon. This can be a main source of variability
for previous accretion differences, in subsurface horizons.
Spatial variation of the organic layer thickness was associated with
variation of the DML. For the saline marsh, the DML was shallower near water
bodies. The soil subgroups, Terric and Typic Medisaprists were delineated
based on the organic layer thickness. Typic Medisaprists occurred mostly
180
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
toward inland areas and away from open water at the saline marsh. The DML
was shallower in the northeastern half of the saline marsh. Typic Medisaprists
occurred in the northeastern part of the brackish marsh site, which had thick
organic layers due to presence of thick Oa2 and O a3 horizons.
High spatial autocorrelation was found for pH of organic horizons for
saline marsh except for the Cg horizon. Lower pH was associated with
degrading marsh patches toward the S W and NE corners of the saline marsh.
A smooth pH gradient from NW to SB direction was observed for the Oa3
horizon at the saline marsh. High spatial variability was found for pH for Oa1
horizon within the brackish marsh site, with lower pH values along the N W to
SB diagonal across the site.
The OM R data ranged widely for the brackish marsh compared to saline
marsh for all organic subhorizons. Higher OM R associated with the northern
part and lower O M R at the southern part of the site indicated sedimentation
variations. The high OM R at the NE and NW corners of the saline marsh can
be attributed to marsh degradation. The OM R data were highly spatially
variable at the brackish marsh site. Higher OMR found inland may be a result
of low sedimentation (inorganic accretions).
Spatial variability can be attributed to long-term influence of processes,
such as sedimentation, organic accretions, consolidation of sediments, and
localized damage by hurricane activity. Understanding of spatial variation of
marsh soil characteristics will help to identify the prominent processes within
the marshes and to plan marsh management strategies.
181
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
High net primary production of coastal marsh in terms of the above- and
below-ground biomass is the main contribution to the fixed carbon pool within
the marsh soil environment. The organic soil profile is comprised of mainly two
layers; the organic layer and the mineral layer. The organic layer can be
divided into different sub horizons based on the color and the composition. The
organic matter accumulation (organic accretion) and sedimentation (inorganic
accretion) are the main processes that contribute to the organic soil formation
(Hatton et al., 1983; Chmura et al., 1992;Nyman et al., 1993). Thickness of the
organic subhorizons varies due to the variations in the organic and the
inorganic accretions and disturbances to the marsh, which reflects the history of
marsh soil formation. Organic accretions vary due to the changes in the
productivity of the vegetation and inorganic accretions vary depending on the
changes in the sedimentation rate within the marsh.
Organic layers degrade in eroding marshes. Organic accretion results in
thick organic layers that help to maintain healthy marshes (DeLaune et al.,
1983). Accretion rates may be variable and the marsh landscape may be
disturbed by hurricane activity, presence of channels, open water areas, and
m an-made changes (Salinas et al., 1986; D e laune et al., 1989). Thin organic
layers may be characteristic of erodible marshes that convert into open water.
Thickness of the surface organic layer is a significant soil morphological feature
that may indicate the current status of the marsh. Depth to mineral layer is
used as soil subgroup differentiae. Understanding spatial variability of organic
layer thickness will enable one to delineate soil subgroups. Critical marsh
182
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
areas may be identified based on soil variability and marsh management
strategies may be planned.
Organic/mineral ratio of the organic soil layers is a result of both organic
accretion and sediment deposition. Sediment deposition rates can be different
within the marsh depending upon the sediment supply. High OMR ratio may be
either due to lack of sediments or high organic accretions. Organic accretion
results in thick organic layers that help to overcome submergence. However,
lack of sediments does not promote organic accretions. Therefore,
organic/mineral ratio can be a suitable indicator to detect the status of the
marsh. It may be directly related to the marsh status; degrading marshes may
have high organic/mineral ratio. Soil pH indicates the biogeochemical status of
the marsh. The spatial variability of pH within the landscape can be associated
with prominent biogeochemical processes within the area.
The thickness of the organic subhorizons is a direct estimate of fixed
carbon. The organic/mineral ratio and pH reflect the compositional and
biogeochemical status of the marsh. Understanding of the spatial variability of
these characteristics more accurately estimates the carbon pool within the
marsh.
Previous studies carried out within the marsh excluded spatial variability
by sampling surface soils at points within close proximity to each other (Feijtel
et al., 1988; Krairpanond et. al., 1992). The point estimates represented the
entire marsh type while not much attention was paid to understanding the
spatial variability.
183
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Practical limitations for sampling restricted detailed sampling within the
landscape. Because of the practical difficulties of a well-planned sampling
scheme within the marsh, understanding the landscape model is helpful to
understanding possible soil variations. Spatial variability data will help plan soil
sampling schemes to be more representative and minimize the number of
sampling points as appropriate. Remotely sensed data are often used in
coastal marsh studies and the spatial variability information also helps a
researcher decide the appropriate pixel size of the remotely sensed data for a
particular study.
This study was planned to assess the spatial variability of organic soil
characteristics at field-scale for brackish and saline marsh types within the
Barataria Bay Basin. The spatial variability of soil morphological data such as
sub horizon thickness, depth to mineral layer, pH and organic/mineral ratio for
different horizons will be studied. Semivariograms will be generated for the soil
variables and associated landscape patterns of these soil characteristics will be
identified.
5.2 Literature Review
5.2.1 Barataria Bay Coastal Marsh
Louisiana's coastal wetlands comprise 41% of the U. S. total coastal
wetlands and are significant as a state, national, and international natural
resource. These wetlands directly support fisheries, wildlife, industry and
recreational needs (Turner, 1990). The coastal wetlands of Louisiana covers
about 3.7 million ha of land and water. This area is comprised of 58% open
184
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
water (2.146 m. ha), 5.6% urban and agricultural lands (0.207 m. ha), 32%
wetlands (1.184 m. ha), and 2 .1% dredged canals and spoil banks (0.078 m.
ha). These wetlands are a combination of six marsh types; salt marsh (15%,
0.1776 m. ha), brackish marsh (47 %, 0.5565 m. ha), intermediate marsh (23% ,
0.2723 m. ha), fresh marsh (12% , 0.1421 m. ha), swamp (<1%), and mangrove
(<1% ). Barataria Bay marshes are a riverine deltaic marsh that extends for an
area of 628,000 ha. The area is divided into three sub basins; upper
freshwater lake (Lac Des Allemands), middle brackish lakes, and lower saline
bays (Barataria Bay and Caminada Bay), lakes and marshes (Madden et al.,
1988).
Marsh loss to open water is a severe problem in the marshes of the
northern Gulf of Mexico. The average annual rate of marsh loss was about
0.86 % from 1955 to 1978 (Turner, 1990). Boesch et al. (1983) reported a loss
of about 49 square miles per year. Inability of the marsh to counter the
subsidence has been reported as the main cause of marsh loss (Turner, 1990;
DeLaune et al., 1994). Marsh is lost to open water when subsidence is greater
than the accretion rates. Because of high Relative Sea Level Rise (RSLR),
deltaic wetlands are affected by an acceleration of eustatic sea-level-rise (Day
et al., 1995). The combination of RSLR and local submergence has been
considered as the apparent sea level rise. Apparent sea level rise is reported
to be around 0.24 cm yr^ for these marshes (Chmura et al., 1992).
Turner (1990) indicated that sediment loading declined drastically in the
mid-1950s after dam and reservoir construction on major tributaries of the
185
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Mississippi River, causing an estimated 50% decrease in sediment input to the
marsh system. Sedimentation (inorganic accretion) and organic matter
accumulation control accretion. Vertical accretion is not simply the result of
sediment supply but also of the interaction of plants and the prevailing
hydrologie regime. Salinity intrusion and other biological factors are known to
be responsible for the above and below-ground production of the marsh
vegetation. W ater logging may be more influential than the sediment
deprivation in relation to marsh loss (Turner, 1990). Water logging can make
the vegetation more vulnerable to dieback due to stress.
One method to determine accretion is the use of the ^ ’'Cs isotope. The
^^ Cs maxima are assumed to result from atmospheric deposition of ® Cs that
marks the 1963 surfaces, rather than that from erosional depositions. The ^ ^Cs
profiles in Louisiana marshes represent continuous atmospheric deposition
rather than discontinuous sediment deposition (Nyman et al., 1993). The ® Cs
dating indicated that vertical accretion (0.98 cm y r ’) was extremely rapid in the
Terrebonne Basin marsh relative to other marsh areas. But this accretion rate
was insufficient to counter submergence (1.38 cm y r ’) (Nyman et al., 1993).
Compaction or consolidation of the sediments will govern the effective accretion
rates (Chmura et al., 1992). Erosion below the root zone is another mechanism
for marsh loss (Nyman et al., 1994), which reduces marsh elevation
considerably. The unconsolidated soil below the living root zone at the marsh-
water interface in the broken marsh areas is eroded and the detached marsh
come to rest on the pond bottom (Nyman et al., 1994).
186
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Catastrophic events influence Louisiana marshes frequently. Hurricanes
bring salt water and sediments inland and also may erode lands due to physical
action of flooding (Childers et al., 1990; Turner, 1990). Hurricane sediments
are not stable since they can be washed away by the consequent flooding
(Turner, 1990). Hurricanes influence the sedimentation variability within the
marsh. Nyman et al. (1995) reported a wide range of deposition thickness (0 to
9 cm) due to hurricane Andrew in Louisiana marshes along the hurricane track.
This suggests that marsh elevation can be increased due to deposits and at
the same time marsh loss may occur as a result of a hurricane.
Marshes are delineated into saline, brackish, intermediate, and fresh
water marshes based on salinity (Feijtel et al., 1988; Soil Conservation Service,
1989). The salinity map indicates isohaline lines from 0.5 to 20.0 ppt covering
the area in east and central Barataria Bay. Salinity ranges between 5 and 10
ppt within brackish marsh while saline marsh has salinity over 10 ppt (Soil
Conservation Service, 1989). Previous work indicated variations sulfur
dynamics due to differences in biogeochemical environment within different
marsh types (Krairpanond et al., 1992a, 1992b). Griffin and Rabenhorst
(1989), Haering et al. (1989) and Lin and Melville (1994) reports variability in
biogeochemical processes following a landscape pattern within marshes
elsewhere.
Micro-scale landscape variation within the marsh causes variation in
vegetation (DeLaune et al., 1983). This suggests the existence of spatial
variability in the rate and amount of carbon accumulation within the marsh at
187
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
small scale. Consequently this can be related to a landscape pattern of marsh
accretion rates and soil morphological variability. Marsh loss is attributed to
plant stress due to salinity and prolonged inundation. Since marsh degradation
affects the soil morphology, thickness of an organic horizon is a suitable
indicator to understand the marsh status. Previous studies were limited to point
sampling within this marsh to exclude spatial variability (DeLaune et al., 1983).
Limited studies attempted to understand the spatial variability of marsh
characteristics. Variations in soil morphology would help to understand the
prominent functions within the marsh and to identify hot spots of degrading
marshes.
5.2.2 Soil Morphology and Classification
An idealized soil profile for the marsh area is presented below (Figure
5.1).
Figure 5.1. An idealized coastal organic soil profile with subhorizons.
188
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
These marshes have a variable organic layer (Oa horizon) over a sandy or
clayey alluvium (Cg horizon). The surface organic layer can be separated into
different sub horizons based on their color differences as Oa1, Oa2, Oa3, and
O a4 horizons. Organic soils within the Barataria Bay Basin are mapped as
associations of soil series in the soil survey conducted in 1981 (Soil
Conservation Service, 1984). The associated series within a particular salinity
regime are delineated based on the depth to mineral layer at subgroup level
(i.e., Terric Medisaprists and Typic Medisaprists). Timbalier-Bellpass
association (TB) is dominant within the saline marsh. According to Soil
Taxonomy, the Timbalier series is euic, thermic, Typic Medisaprists while the
Bellpass series is clayey, montmorillinitic, euic, thermic, Terric Medisaprists.
The Lafitte-Clovelly association (LA) dominates the brackish marsh. The Lafitte
soil series is an euic, thermic, Typic Medisaprists while the Clovelly soil series
is a clayey, montmorillinitic, euic, thermic, Terric Medisaprists. Terric
Medisaprists are the Medisaprists that have a mineral layer 30 cm or more thick
that has its upper boundary within the control section (130 cm) below the
surface tier (60 cm). Other Medisaprists that have the upper boundary of the
mineral layer below control section (130 cm) are Typic Medisaprists. The main
difference between these soil series is the depth to the mineral layer.
5.2.3 Spatial Variability of Marsh Soil Characteristics
Marsh elevation changes from highest at the streamside to lowest in the
inland area. This change is associated with variation in soil and plant
characteristics along this marsh landscape (DeLaune et al., 1983). Marsh loss
189
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
is associated with soil water logging and salt-water intrusion into non-saline
marshes (Nyman et al., 1993; DeLaune et al., 1994). Total plant mortality
occurred within one year, and hummock elevation decreased almost 15 cm
within two years in a Louisiana marsh (DeLaune et al., 1994). Increased
sediment sources, maintenance of natural hydrologie regime and sediment
distribution, and lower rates of sea level rise contribute to wetland growth.
Considering these factors, different horizonation can be expected within the
organic soil profile. This may lead to spatial variability of relative marsh
elevation within this area. Spatial variability of soils is the integrated outcome
of these various activities happening within the marsh. Identification of spatial
variation of marsh characteristics may enable one to identify the dominant
processes controlling the marsh loss or growth within the area.
5.2.4 Spatial Interpolation Methods
Spatial variability of soils within landscape was identified at the early
stages of soil science when pedologists identified different soils associated with
the landscape position (i.e., Glazovskaya, 1968). In recent soil science
research, spatial variability of soil characteristics at field-scale has been the
interest of many scientists, and the understanding of its impact on soil and crop
management practices has improved.
Application of mapping science techniques such as geostatistics and
Geographic Information Systems (GIS) at field-scale is helpful for the soil
scientist to identify landscape relations of soils. The underlying pedological
processes have been identified within the landscape from spatial patterns of
190
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
soil properties (Hanna et a!., 1982). Reese and Moorhead (1996) identified
spatial characteristics of soil properties along an elevation gradient. McDaniel
et al. (1992) presented pedochemical indicators to mark field-scale through flow
water movement within the landscape.
Use of data interpolation to identify the surface model to predict the
values for points that have not been measured, is imperative. Lam (1983)
presented a comprehensive review on spatial interpolation methods. With the
rapid expansion of GIS, spatial data analysis and spatial interpolations require
special attention. The following section presents several spatial interpolation
techniques and concerns in soil science.
Performance of different spatial interpolation methods for soil
parameters were presented by W ebster and Oliver (1989), Knotters et al.
(1995), Barry and Ver Hoef (1996), Brus et al. (1996), and G o tw ayeta l. (1996).
The relation of an appropriate interpolation model depends largely on the type
of data, the degree of accuracy desired, and the computational effort afforded.
Every model is based on a hypothesis about the surface, which may or may not
be true (Lam, 1983). Spatial interpolations are either point interpolations (i.e.,
temperature, elevation) used for isometric maps, or areal interpolations (i.e.,
population density) used for isopleth maps. For both interpolations, they can be
either exact or approximate methods depending on whether the method
"preserves or not” the original sampling point values. Depending on the extent
of the data points involved, the point interpolation methods are classified as
global or piecewise methods. The global methods utilize all sample points to
191
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
determine a value at a new point, while only the nearby points are used by the
piecewise methods.
The interpolation methods also can be categorized as statistical or
analytical. Kriging is considered a statistical technique while other methods are
considered as analytical techniques. Lam (1983) preferred to classify point
interpolation methods as either exact or approximate methods because
preservation of original sampling point values on the inferred surface seems
fundamental in analyzing accuracy and in examining the nature of interpolation
methods. Interpolating polynomials, most distance-weighting methods, kriging,
spline interpolation and finite difference methods are exact methods. The
group of approximate methods includes power-series trend models, distance-
weighted least squares and least square fitting with spline (Lam, 1983).
The principle of distance-weighting methods is to assign more weight to
nearby points than to distant points. The usual expression is
f(x,y) = [ Z w(di)Zj] / [ Z w (d |) ] [5 .1 ]i= 1 i= 1
W here w(d) is the weighting function, Z| is the data value at point I, and d | is
the distance from point i to (x,y). The disadvantages of the weighting methods
are, one is the ambiguity introduced by the weighting function and second is
that the method is affected by uneven distributions. Weighting functions are
essentially smoothing procedures. It is considered as a limitation because the
contours should be able to predict the important features such as maximum
192
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
and minimum when they are not included within the data set. However, the
simplicity of the principle, the speed of calculation, the ease of programming,
and reasonable results for many types of data have led to wide application of
the weighting methods (Lam, 1983).
Kriging, perhaps the most distinctive of interpolation methods, has
become a major tool in the field of geostatistics. Kriging treats the statistical
surface of interpolated data as a regionalized variable with continuity. More
information on kriging can be found in Isaaks and Srivastava (1989) and
Goovaerts (1997). Two systems of kriging procedures, simple kriging and
universal kriging, can be distinguished based on the assumptions about the
regionalized variables. Mathematically, a semivariogram (y) is defined by:
N
y =%N E [z (X |+ d ) - z (X j) ]^ [5.2]
1=1
d = distance between two samples, and Z is the data value at points.
Parameters for a semivariogram are presented in Figure 5.2.
Sill
8CCO'C
iÎCO
Nugget Range
Lag Distance
Figure 5.2. Major features of an ideal semivariogram.
193
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
A line can be fitted for the semivariance function with lag distance. The
three properties of the model are the nugget, sill, and range (Figure 5.2). The
nugget is the intercept that is theoretically zero for lag distance of zero.
However, it may deviate from zero depending on the sampling and short
distance variability. The nugget is the amount of variability that is not included
into the spatial correlation model. The leveling off of the semivariogram model
forms the sill, but for a linear model, it may not present. Beyond the sill, the
semivariance on the average is constant or independent from lag distance.
The lag distance value where the semivariance reaches the sill is the range.
The range represents the maximum separation distance within which the
sample values are spatially correlated (Rossi et al., 1992; Smith et al., 1993).
When the semivariance reaches the sill, sample locations are separated
enough to be independent. The range of correlation indicates the relationship
between spatial variability and random variability within the site. Random
variability occur between samples that are farther apart than the range and
spatial variability occur between samples closer together within the range
(Flatman and Yfantis, 1996).
Four common shapes of the semivariance models are linear, spherical,
exponential and guassian. Linear semivariogram with a sill may also be used
(Gamma Design Software, 1994). Simple kriging has more restrictive
assumptions but fewer computational problems, whereas the universal kriging
has more general assumptions but difficult calculation (Lam, 1983). Increasing
nugget effect increases the ordinary kriging variance and makes the estimation
194
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
procedure become more like simple averaging of data. The ratio of the nugget
to the sill is referred to as the relative nugget effect that is usually quoted in
percentages. The change of the range has relatively minor effect on the
ordinary kriging weights (Isaaks and Srivastava, 1989).
Accuracy of the inverse distance methods increased with the power of
distance for data sets with low coefficient of variation (CV) (< 25% ). High
distance powers in inverse distance methods can give very inaccurate
predictions for data sets with C V higher than 25%. Accuracy of kriging is
generally independent from the CV of the data set (Gotway et al., 1996). Brus
et al. (1996) compared the performance of six spatial interpolation methods,
global mean, moving average, nearest neighbor, inverse squared distance,
Laplacian smoothing splines, and ordinary point kriging. Soil properties
included thickness of the A horizon, soil adsorbed phosphate, and water table
depths. Differences between methods were small. However, Brus et al. (1996)
found kriging was more reliable because it estimated all properties well.
Therefore, Kriging can be used as a interpolation method when the variable has
a well structured spatial variability that can be explained by a semivariogram.
5.3. M aterials and M ethods
5.3.1 Site Description
Two sites were selected representing saline and brackish marsh types
within the Barataria Bay (Figure 5.3). Both sites were in Lafourche Parish. The
saline marsh site was located at N 29° 14' 44", W 90° 07' 16" and the dominant
vegetation was S partina a ltem iflo ra . The brackish marsh site was located at
195
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
f
im
IIoU5
0)O)CDE
CO03C0 c1CO
S'
03EJZ.SGo2_o03B■ac03
S
ECD
£03C
I d£/)03x:
toc0
101c/)COUO
EZJ03
196
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
N 29° 16' 35", W 90° 08' 10", and was predominantly covered by S partina
pa tens and D istich lis . Data were collected in 1990 for both sites, each site
covering a one-square mile area.
Figure 5.4 presents site maps for saline and brackish marsh types.
Maps only show the dominant open water areas and waterways within the
sites. The saline marsh site has two major open water areas that are
separated by broken marshes at the southern part of the site. Two other open
water areas are in the NE section of the site. The waterway, which enters from
the north, is divided into two branches and flows into opposite directions; one
westward and the other eastward. The brackish marsh site is comprised with
vast areas of broken marshes that occupy the entire NE and NNW sections of
the site. The major waterways that flow through the site have been blocked at
the center so that only the water from the west and the south mixes. Major
open water areas are found within the SW section and the minor waterway in
the east expanded into a open water area within the SE section.
5.3.2 Data Collection
Soil morphological data and pH were collected from saline and brackish
marsh types. Soil profiles were sampled on a grid formed by transects of 200-
m interval established in both directions across the sites (Figure 5.5). Samples
were collected at 400-m interval on each transect along north-south direction.
Data included thickness of organic subhorizons (Figure 5.1), depth to mineral
soil layer and pH for each soil subhorizon. Depth to mineral soil layer was
similar to the total thickness of organic matter because the samples were
197
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
1600
1400
1200
1000
I 800
IQ 600
400
200
0
1600
1400
1200
1000
I 800
Q 600
A
W
{ 1 W '
w
w„
w
ww
A. Saline marsh
400
200
0
A
w
w0 200 400 600 800 1000 1200 1400 1600
Distance (m)B. Brackish marsh
Figure 5.4. Maps showing dominant open water areas (W ) and waterways within the sites at saline (A) and brackish (B) marsh types.
198
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD■ D
OQ .C
gQ .
■DCD
C/)Wo'3O
8■D
3.3 "CD
CD■DOQ .C
aO3
■DO
CDQ .
■DCD
C /)C /)
1600
CDCD
€o
8
Ib
1200
800
400
,, * * # a\f w w w #
. i 1 1 1 :
; : M ,
. : : n........ "#
I i Î I : 1 1 ^ F W W W
A ' À 1 À 1 :T T •
.. ! 1 1 1 1 .
' i
11 W , W ; W
1 1 1 I 1 ;
# '!
. . 1
„ ! 1 1 ! L ... I 10 400 800 1200 1600
Distance (m), East - West
Figure 5. 5. Sampling plan for both sites, showing the sampling points on the grid.
collected within vegetative areas. The pH was measured with a pH meter
(Orion Research model 701A/digital lONALYZER). Organic and mineral
contents were estimated on weight loss basis after burning the samples at 425
°C. The variables used for each site are given in Table 5.1.
5.3.3 Data Analysis
The first task in all geostatistical investigations is to conduct exploratory
data analysis (EDA) (Rossi et al., 1992). The EDA was conducted using the
SPSS software (SPSS Inc., 1997). Boxplots were used to present the data
sets and to identify outliers and compare the variables between marsh types.
Spatial data analysis was conducted using the GS^ software (Gam m a Design
Software, 1993). Semivariograms were constructed and appropriate models
were fitted for each variable. The data set was not trimmed to obtain better
shaped semivariograms as is common for some studies (Cahn et al., 1994).
Contours were generated using SURFER software (Golden Software Inc.,
1995), interpolating data for a finer grid with 50-m intervals. Kriging was used
for the variables that have a good spatial structure explained by the
semivariogram models, otherwise the inverse distance squared method was
used to interpolate data.
200
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Table 5.1. The variables used for spatial analysis for each marsh type.
Variable Name Code^
Thickness of the O a l horizon = 0A 1TH
Thickness of the Oa2 horizon = GA2TH
Thickness of the Oa3 horizon = OA3TH
Depth to mineral soil layer^ = □M L
pH of the O a l horizon = GA1PH
pH of the Ga2 horizon = 0A 2P H
pH of the Ga3 horizon = 0A 3P H
pH of the Cg horizon = CGPH
Weighted average pH for the organic layer = W GPH
Organic/mineral ratio* for the G a l horizon = GA1GMR
Organic/mineral ratio for the Ga2 horizon = 0A 2G M R
Organic/mineral ratio for the Ga3 horizon = 0 A 3 0 M R
Weighted average “omr" for the organic layer = W GM R
^ S o r B will proceed the code to indicate saline (S) or brackish (B) marsh.
^Mostly similar to the thickness of total organic layer
^Organic matter content / mineral matter content
201
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
5.4 Results and Discussion
5.4.1 Thickness of Organic Subhorizons
5.4.1.1 Exploratory Data Analysis
The number of subhorizons within the profile varied widely within both
sites. Most of the sampling points had Qa1 and G a2 subhorizons, but the Ga3
horizon was absent at some sampling sites. Some sampling points had an Ga4
horizon, mostly at the brackish marsh site. Very few locations had mineral soils
at the surface.
Boxplots for the data on thickness of organic subhorizons are presented
in Figure 5.6. The components of a box plot are 25^, 50"' (median), and 75*"
percentiles and the lower and upper fences. The upper fence equal to 7S'"
centile + 1 . 5 * interquatile range (IQR), and the lower fence equals to 25'"
centile - 1.5*IQR. Data values above or below the fences are designated as
outliers. The SGA1TH data indicated more variation compared to BGA1TH
data. The range (0 and 50 cm), median (25 cm) and mean (26 cm) for G a l
horizon thickness were similar for both sites. Data for SGA1TH and BGA1TH
were normally distributed. Thickness of the Ga2 horizons was higher
compared to that of the G a l horizons at both sites. The SGA2TH ranged
between 0 and 100 cm while the BGA2TH ranged between 0 and 90 cm,
resulting in a higher mean for the saline marsh (48 cm vs. 37 cm). The
BGA2TH data followed a bimodal distribution. A bimodal distribution may
indicate that the variable is comprised of two populations that are under control
of two different processes. The Ga3 horizon thickness data followed bimodal
202
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
120
Eü
ïü
S 0A 1TH S 0A 2T H S 0A 3T H
B 0A1TH BOA2TH BOA3TH
Subhorizon
Figure 5.6. Boxplots showing the data for organic subhorizon thickness at both sites.
203
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
distribution at both sites; for SOA3TH the modes were at zero and 35 cm, for
B 0A 3TH the modes were at zero and 50 cm. Both sites had about 50% of
sample points that did not have the Oa3 horizon, which is indicated by the
boxplot for the S 0A 3T H that has its median at zero. In general, thickness
variation is higher for the lower subhorizons within the profile (Figure 5.6).
5.4.1.2 Spatial Data Analysis
Semivariograms were constructed using horizon thickness data from
both sites, and best models were selected based on the regression coefficients.
The model parameters are given in Table 5.2.
Table 5.2. Modal parameters and regression coefficients, for the semivariograms for the thickness of organic subhorizons at both sites.
Variable^ Shape Nugget (cm^) Sill (cm^) Lag (m) R:
S 0A 1TH spherical 14 83 684 0.993
S 0A 2TH spherical 162 451 609 0.995
S 0A 3TH spherical 331 941 1392 0.973
B0A2TH spherical 168 485 548 0.935
B0A3TH spherical 250 1060 1607 0.983
BOA1TH data did not fit a semivariogram model.
The data for B 0A 1TH did not fit a semivariogram due to lack of spatial
variability within the data set. Data for the thickness of other subhorizons at
both sites indicated significant spatial autocorrelation that was explained by
spherical models (Table 5.2). Semivariograms for SOA1TH, SOA2TH, and
204
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
S 0A 3TH are presented in Figure 5.7. The sill is higher for the SOA2TH and
SOA3TH compared to S 0A 1TH . The range of spatial correlation is higher for
S 0A 3TH . Figure 5.8 presents the semivariograms for B0A1TH, BOA2TH, and
BOA3TH. Range of spatial correlation was smaller for B0A2TH compared to
B0A 3TH . The B0A1TH data did not show any spatial correlation. The
semivariograms for B0A 3TH had higher sill effect compared to other
semivariograms. The spatial variability of organic horizon thickness could be
attributed to long term influences on processes, such as sedimentation, organic
accretion, and compaction, which can make a significant variation. On the
other hand, this may be indicative of the localized damage to the marsh by
hurricanes or other marsh loss mechanisms.
Kriging was performed and the contour plots were generated for all the
organic horizons that produced good spatial structure. For BOA1TH, the
inverse distance squared method was used to interpolate data. Contour plots
for the Oa1, Oa2, and Oa3 horizon thickness data are presented for the saline
marsh (Figure 5.9) and brackish marsh (Figure 5.10). Thicker O a l horizons
were found at the edges of the water bodies indicating predominantly accretion
within the area at the saline marsh. The peaks were prominent because of the
presence of shallow areas with open water. Thickness of the O a l horizon was
thin towards the open water (Figure 5.9). It may be due to the accretion
differences between streamside and inland within the landscape. The O a l
found in inland may not be contemporary to the O a l at the streamside.
205
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
ooCD
T 3
OOCM
g(73•acCD
OO00
8
O )CD
iC/D
OC/D
OC/D♦
gCD
iCD
OoM-
O)E2C3)O
îîCDMtri23O)
ooo
ooco
ooCD
oo•M-
OOCM
(^LUO) aO U B U B A ILU aS
206
ReprocJucecJ with permission of the copyright owner. Further reproctuction prohibitect without permission.
I X X1— 1— 1— oT- CM CO o< < <o o oCO CO COO □ O
o
o□
o
o o
□o o
o o□
o o
o □ o
oooCNJ
oolO
ooo
s
IQ
ooIT)
■D
im-ocm
Im
Î2 X
oco
E2O)0"C
1EmWodiri2 3 D)
OOOOg
O§
ooMooco
oolOoo oo
coooCM
oo
( lUO) GOUBUBAjOISS
207
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
1600
o 1200
1 800
II 400 b
0
1600
1200
800
^ 400I0
1600
g 1200
800
i 400 S
OS
( )
\ \
è
S0A1TH
!
OP’
09
/ &
S0A2TH
/' /
I ?/ /
Ù \ 800
SOA3TH
1600400 800 1200Distance (m), vest - east
Figure 5.9. Spatial variability of 0 a 1 , Oa2, and O a3 horizon thickness for the saline marsh.
208
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
1 6 0 0
1200
800
f 400 G
0
1600
1200
( )<§>
1 800
I «>s
01600
Q 1200
( ;S
(f. 3o
!ë
9 ) ; s
0 % I .
/
S
8C(D
800
S 400
%
1 0
'è
30
AO
BOA1TH
BOA2TH
B0A3TH
0 ........400 800 1200 1600
Distance (m), west - east Figure 5.10. Spatial variability of Oa1, Oa2, and Oa3 horizon
thickness for the brackish marsh.
209
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
This may be the main source of spatial variability for organic subhorizon
thickness within a site.
Thickness of the 0a1 horizon was uniform within the brackish marsh
site, except randomly occurring peaks and falls due to the main waterway lying
NW to SE diagonal across the site. Thickness of the Oa2 horizon was highly
variable at both sites. Thicker areas associated with water bodies at the saline
marsh site (Figure 5.9), may be indicative of persistence of accretion processes
at the site. At the brackish marsh site, the Oa2 horizon was thinner near the
streams (Figure 5.10). This may be due to subsurface erosion within the area,
which may be aggravated by the waterways. The contour plot for SOA3TH
shows a uniform gradient from NW towards the eastern sections of the site
(Figure 5.9). Previously the stream at NW corner may be the main source of
accretions. The inland may be converted to open water later and the present
landscape may be developed due to marsh loss or by catastrophic action of
hurricanes. For the brackish marsh type, the Oa3 horizon was thin within the S
to W section, which coincides with the present water body. The stream located
at the western edge of the site may be developed later and separated the water
body (Figure 5.10).
5.4.2 Depth to Mineral Layer (DML) and Soil Subgroup Delineation
5.4.2.1 Exploratory Data Analysis
Several sampling points had standing water as they occurred in open
water. Except at those points, the DML is equal to the total organic layer
thickness, which is depth to the surface of the mineral soil layer (Cg horizon). A
210
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
mineral subhorizon (Cg2 horizon) also was found at many sampling points.
Figure 5.11 presents boxplots for the DML for both sites. The BDML had
higher variation compared to SDML, but the mean values were very similar
(104 cm). The SDML ranged from 50 to 150 cm while the BDML had a higher
range for BDML (0 to 165 cm) due to the presence of a surface mineral layer
for some sampling points.
The SDML data followed a bimodal distribution indicating that the data
may represent two populations. Presence or absence of the Oa3 horizon within
the profile was also associated with the difference. The Oa3 horizon thickness
was highly correlated with the SDML. The bimodal variation of data on SDM L
could indicate presence of depressions at the surface of the mineral layer due
to accretion differences within the site.
The BDML data followed a left skewed unimodal distribution and
associated with absence of an Oa2 horizon, Oa3 horizon, or both within the
profile. The Oa2 and Oa3 horizon thickness were highly correlated with BDML.
North to northeastern parts of the brackish marsh site had higher DML as well
as thicker organic horizons (Oa2 and O a3 horizons), indicating accretion
differences at the mineral layer, similar to the saline marsh site.
Exploratory data analysis indicated that the DML varies and correlated
with the presence or absence of organic horizons and their thickness variations.
This may indicate that more accretions occur where the mineral layer is
deeper. The Oa2 and Oa3 horizon thickness may vary due to variations in
accretion rates between depressions and other areas at the mineral layer.
2 1 1
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Eo
m
I
I
2 0 0
150
100
SDML BDML
Marsh Type
Figure 5.11. Boxplots showing the data for depth to mineral layer (DML) for both sites.
212
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Loss of a subhorizon or thin subhorizon can be due to erosion of lower organic
horizons, however this occurs at marsh-water interface of the degrading marsh.
Subsurface erosion is one of the major causes of marsh loss (Nyman et al.,
1994).
5.4 2.2 Spatial Data Analysis
The semivariograms are presented in Figure 5.12 for SDM L and BDML.
The lag distance of spatial correlation was higher for SDML (1476 m) compared
to the BDML (690 m). The BDML had higher sill effect compared to SDML.
Table 5.3 present model parameters for the semivariograms.
Table 5.3. Modal parameters and regression coefficients of the semivariograms for the DML at both sites.
Variable Shape Nugget (cm^) Sill (cm^) Lag (m) R:
SDML spherical 298 839.1 1476 0.939
BDML spherical 104 2162 690 0.928
Contour plots were generated by kriging using the semivariograms for
SDML and BDML (Figure 5.13). For the saline marsh site, shallow DML was
found close to the water bodies and deeper DML was found at the edges of the
site. Total organic layer thickness decreased towards the main waterway that
flows along the diagonal of the brackish marsh site. The BDML was very
shallow due to presence of surface mineral layer in this area.
213
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
oolO
omCM
OOo
sr--
oom
omCM
SIQ
T 3
QCO■acCO
QCOm
E5C3)OC. i
CO
c\i
m(D
.g)u_
o o o o o oo o o o oin o in o inCM CM T—
(^Uio) aouBUBAjUjas
214
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
■coc
ov>
S
Ib
o
3Otfl
S
IQ
1600
1200
800
400
0
1600
1200
800
400
0
%
6o
I
09
00 L
%\
z.
<%? ^Oq
Oq
Ooi
o
! i /\ i
' \ 1,
A. SDML
400 800 1200Distance (m), west - east
B. BDML
1600
Figure 5.13. Spatial variability of depth to mineral layer for the saline marsh (A) and brackish marsh (B).
215
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
5.4.2 3 Spatial Distribution of Soil Subgroups
The soil subgroups, Terric and Typic Medisaprists, were delineated
based on the organic layer thickness on the contour maps generated for SDML
and BDML. Soils that have the upper boundary of mineral layer within the
control section (130 cm) and below the surface tier (60 cm) are Terric
Medisaprists. If the upper boundary of the mineral layer occurred below control
section (130 cm) then they were delineated as Typic Medisaprists.
The DML was shallower in the north - eastern half of the saline marsh
site where the marsh is being converted into open water. Typic Medisaprists
occurred mostly toward inland areas away from open water and streams. Rest
of the area was delineated as Terric Medisaprists (Figure 5.14). At the saline
marsh site the Timbalier series is the Typic Medisaprists while the Bellpass
series is the Terric Medisaprists. Typic Medisaprists occurred in the north to
northeastern parts of the brackish marsh site, which had deep DML due to thick
organic horizons (Oa2 and Oa3 horizons) (Figure 5.14). The Lafitte soil series
is the Typic Medisaprists while the Clovelly soil series is the Terric Medisaprists
at the brackish marsh site.
5.4.2 pH for Different Subhorizons
5.4.2.1 Exploratory Data Analysis
The pH data for different soil subhorizons and weighted average pH for
the organic layers are presented in Figure 5.15. Mean pH for horizons for the
saline marsh was always lower than in the brackish marsh. This may be due to
higher accumulation of reduced sulfur material for the saline marsh compared
216
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
1600 -*---- —
1400
S
IQ
1200
1000
800
600
400
200
0
&Terric Medisaprists
Typic Medisaprists
0 200 400 600 800 1000 1200 1400 1600Saline marsh
1600
1400
1200
E,1000
o>Üc 800SQ 600
400
200
0
‘ i.-’
09
• C’ Î Î ,
<■' '
^ Terric Medisaprists
200 400 800 800 1000 1200 1400 1600Distance (m)
Brackish marsh Figure 5.14. Spatial varibility of the soils for the saline
and brackish marsh types.
217
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD"OOQ .C
gQ .
"OCD
C/)Wo"3O
8"O
CD
3.3 "CD
CD"OOQ .C
ao3
T3O
(DQ .
M0 0
g
8
7
Q .
6
5
4S0A1PH S0A2PH S0A3PH SCGPH SWTORPH
B0A1PH B0A2PH B0A3PH BCGFH BWTORPH
Subhorizon
T3(D
C/)c/)
Figure 5.15. Boxplots showing the data for pH of soil subhorizons and weighted average pH for the organic layer for both sites.
to the brackish marsh. The pH of the Oa1 horizon, saline marsh (SOA1PH)
and brackish marsh (BOA1PH) indicate similar variation. The S 0 A 1 P H and the
BOA1PH followed normal distribution with means at 6.3 and 7.0, respectively.
The pH of the Oa2 horizon also follows approximately normal distribution for
both sites with means of 6.5 for S 0A 2P H and 7.1 for BOA2PH. The S 0A 3P H
followed a left skewed distribution with a mean of 6.5 while the B 0A 3P H
followed approximately normal distribution with a mean of 6.9. The distribution
of the SCGPH was bimodal with a range of 6.4 to 7.7. The BCGPH was
normally distributed with a wide variation, ranging from 5.2 to 7.2. Weighted
average pH for the organic layers at both marshes are comparable.
Distribution for SW OPH was bimodal while BWOPH followed a left skewed
distribution.
5.4.2 2 Spatial Data Analysis
Semivariograms for pH of different subhorizons are presented in Figure
5.16 for the saline marsh, and Figure 5.17 for the brackish marsh. Table 5.4
presents the model parameters of the semivariograms for pH for different
subhorizons. High spatial autocorrelation was found for pH of organic
subhorizons for the saline marsh. However, the pH for the Cg horizon did not
show any spatial autocorrelation. Contour plots showing pH variation within
different subhorizons of the saline marsh is presented in Figure 5.18. The
SOA1 PH was higher and uniform within the western half of the site. Lower pH
was found towards the S W and NE corners of the site where degrading
marshes occur. Similar spatial pattern was observed for the SOA2PH at the
219
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
on
ooo
o so
tnoCMd
lOCM
OCOinCOd o
ooR
oolO
ooo
8cCO
O)CO
OOin
T 3
XQ.0 ü CO■OcCO
Xo.
gCO
XCL
gCO
1
gCO
12 C3)0 "C1E0)COdd2 3 C3J
aouBUBAjujag
220
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
lO
cmooo
oc n
ooCO
ddlOd
COd
IT3XCLÜÜCOT3CCO
Q.
iCO
^ X
& ^
8
IQ
oCO
Q .
5 gCO
(/)E2O)gCD>
ÎCO
lO23LL
90UBUBAILU9S
221
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Table 5.4. Semivarlogram model parameters for pH of soil subhorizons at both sites.Variable" Shape Nugget Sill Lag (m)
SOA1PH exponential 0.0933 0.1973 445 0.989
SOA2PH linear 0.0632 0.3171 2263 0.836
SOA3PH linear 0.0474 0.1895 2263 0.900
SW O PH linear 0.0427 0.2153 2263 0.845
BOA1PH spherical 0.0085 0.2165 480 0.920
BOA2PH spherical 0.1371 0.2141 856 0.732
BW OPH spherical 0.0406 0.1726 672 0.921
^ SCG PH, B 0A 3PH , and BCGPH data did not fit a semivarlogram.
222
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD■ D
OQ .C
gQ .
■DCD
C/)C/)
8■D
3.3 "CD
CD■DOQ .C
aO3"OO
CDQ .
roroCa)
1600-
g 1 2 0 0 !I
§ o800!
§ i<5 400, (0
0 -1600-
tc 1200i
3
8
S
80CH
S 400i5 I
p>Oï m<D
\0.tO
A. S0A1PH
Ia>If
C. S0A3PH
6.5-lO(d
3S
1600-
12001
800
iS>
8ra 400h□ i
o;160Ck-
rc 1200,I i
800i
s 400i.<aa
6.5
B. S0A2PH
lOtd
D. SCGPH
T3(D
(/)(/)
400 800 1200
Distance (m), west - east
1600Or 400 800 1200
Distance (m), west - east1600
Figure 5.18. Spatial variability of soil pH for O a l (A), Oa2 (B), Oa3 (C), and Cg (D)horizons for the saline marsh
saline marsh site with reduced pH in western portion of the site. A smooth pH
gradient from NW to SE direction was observed for the S 0A 3P H . The SCGPH
was quite uniform within the site with few exceptions. Figure 5.19 presents the
spatial variability of soil pH for different subhorizons at the brackish marsh. The
BOA1PH indicated high spatial variability, with lower pH values along the NW
to SE diagonal across the site. Lower pH values were observed for samples
close to open water areas. Similar spatial pattern was observed for the
BOA2PH but towards the NE corner of the site, pH increased then leveled off
and decreased. The decrease may be associated with open water areas. The
BOASpH and BCGPH did not show any spatial autocorrelation. Spatial pattern
for the BOASPH was similar to that of Qa2 horizon. The BCGPH was uniform
except around the SW section of the site where the pH was highly variable.
This may be due to closer proximity of the open water areas that promotes
leaching of acidic material into the Cg horizon.
5.4.3 Organic/Mineral Ratio (OMR) for Different Subhorizons
5.4.3.1 Exploratory Data Analysis
Organic/mineral ratio data ranged widely for the brackish marsh site
compared to saline marsh site for all organic subhorizons. Figure 5.20
presents the boxplots for the O M R data for different subhorizons and for the
weighted-average of the organic layer. Organic/Mineral ratios were higher for
the brackish marsh site indicating more organic material compared to the saline
marsh site. The S O A 10M R data were normally distributed with a mean of
0.529. Right skewed B 0 A 1 0 M R data had a higher mean (1.637) with two
224
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CD■ D
OQ .C
gQ .
■DCD
C/)C/)
8■D
CD
3O(/)
S
I
1600
1200,
800
400
A. B0A1PH
-j’o
O )bi - 1
'oo.r-
7.0
■co
1600
1200Î
800i
§I 400]â i
B. B0A2PH
3.3"CD
CD■DOQ .C
ao3T3O
(DQ .
T3(D
(/)(/)
rototn
Ol
1600-
I 1200'
C. BOASPH
38
S
800
OZm 400' (0
0-1600r
400 800 1200
Distance (m), west - east
1600
c 1200]
§ :S 400]3 ;
o.r-
D. BCGPH
800] O'L
s>.T-
0 1600400 800 1200
Distance (m), west - east Figure 5.19. Spatial variability of soil pH for Oal (A), Qa2 (B), Ga3 (C), and Cg (D)
horizons for the brackish marsh.
CD■ D
OQ .C
gQ .
■DCD
C /)C /)
8
ci'
33 "CD
CD■DOQ .C
aO3"OO
CDQ .
ma:
Ic
ü'c§,o
5
4
3
2
0S0A 3 SW TD
B0A3
S0A1 S0A 2
B0A1 B0A2 BWTD
Subhorizon
■DCD
Figure 5.20. Boxplots showing the data for organic/mineral ratio (OMR) for different organic subhorizons and weighted average OMR for the organic layer for both sites.
(/)(/)
outliers. The S O A 20M R data showed a bimodal distribution with a mean of
0.790. The B 0 A 2 0 M R data were normally distributed with a wider range and
its mean was 2.034. The B 0A 20M R data were highly variable. The
S 0 A 3 0 M R data were normally distributed and very similar to the O a l horizon
data. The B 0 A 3 0 M R data were bimodal with the lowest mean (1.202) at the
brackish marsh. The weighted OM R data for the saline marsh (SW OM R)
followed a bimodal distribution with a mean of 0.640. The BW OMR data were
normaily distributed with a mean of 1.506.
5.4.3 2 Spatial Data Analysis
Well-structured semivarlogram models were fitted only for O a l horizon
for the saline marsh (Figure 5.21 ), and for Oa2, and Oa3 horizons for the
brackish marsh (Figure 5.22). The semivarlogram model parameters are
presented in Table 5.5.
Table 5.5. Model parameters and regression coefficients for the semivariograms for OMR for organic soil subhorizons at both sites.
Variable^ Shape Nugget Sill Lag (m) R2
S 0 A 1 0 M R linear 0.0271 0.0456 2263 0.871
SW OM R linear 0.0373 0.0615 2263 0.493
B 0 A 2 0 M R spherical 0.143 0.501 561 0.934
B O A 30M R linear 0.145 1.124 2263 0.787
BW OMR spherical 0.173 0.356 799 0.683
S 0 A 2 0 M R , S 0 A 3 0 M R , and B 0A 10M R data were not autocorrelated.
227
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
□
Qi a: ce
o oi s
œ (O c/3 O □ <g
□
O
□
□
□ < o
□ < o
0
1
oom
ooo
oCM
LOO
od
ood
8
IQ
Ooin
T3
O
§COT3Cm
0
1CO
ce<2 O
gO)CDJC
CO
IO)o*wffl>E(D
CO
CMlOÿ.3.g)LL
aouBUBA^uag
228
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
oc a: a:
8 §o o
00 00 00o □ <g
<
□
i:
□
<□
oooCM
OOm
ooo
oocsi
oCO
oCM
ooo
oMfCO
oo
8cCD
O)CD
oolO
T 3
OCso
g00TDCCD
OC
o
g00
oc
g00eu
c/>iO)0"C1Ec%c\iCMcri2 o c:)
90UBUBAIUJ8S
229
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
The inverse distance squared method was used for spatial interpolation for the
variables that do not fit a semivariogram.
Figure 5.23 presents contour plots for OMR for soil subhorizons at the
saline marsh site. Higher OM R associated with northern part of the site. This
indicates more sedimentation for the open water areas within the southern part
of the site. The S 0 A 2 0 M R data were highly variable but did not show any
spatial autocorrelation. The S O A 30M R was uniform within the site with few
exceptions and the NE and N W corners had the highest organic matter content.
This may be attributed to marsh degradation at these locations within the site.
High spatial variability was evident at the brackish marsh site (Figure 5.24).
The B O A 10M R data were uniform with an exception of a high organic patch at
the western part of the site. Higher organic/mineral ratios were associated with
inland of the landscape indicating lack of sedimentation in Oa2 and O a3
horizons. This may also be due to subsurface erosion close to open water
areas or waterways. Mineral sediments from the degrading surface organic
layers may be washed away or moved into subsurface organic horizons.
Weighted average of the organic/mineral ratio was used as a separate variable
to study the composition of the organic layer at both sites. Spatial variability at
the brackish marsh site indicates the increased mineral content towards open
water areas.
5.5 Conclusions
Thickness of the Oa2 and Oa3 horizons were highly variable compared
to the Oa1 horizon. Variation of horizon thickness was greater at depths within
230
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
1600
g 1 2 0 0
3
& 800
II 400b
01600
o 1200
0.6
0.5
3O(n
8
800
I 400 b
01600
I 1200
) / ) (
I ).o
00o/
3o0) 800
8I 400 b
(\f>.o
0.5
400
■C>o,
(A)
(B)
(C)
800 1200 1600
Distance (m), west - east Figure 5.23. Organic/mineral ratio for the O a l (A), Ga2 (B), and OaS (C)
horizons at the saline marsh.
231
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
1600,
1 1200
800
I 400
01600
€g 1200
38
800
Iè 400ë
01600
Ic 1200
I 800
IJS 400 wB
2.0
O f
la
^■0
2.0
roo\
400 800
■O
1200
(A)
(B)
(C)
1600Distance (m), west - east
Figure 5.24. Organic/mineral ratio for the O a l (A). Q a2 (B), and G a3 (C ) horizons at the brackish marsh.
232
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
the profile. Except for the thickness of the 0a1 horizon within the brackish
marsh, organic horizon thickness showed high spatial autocorrelation, and the
semivariograms represented spherical models. Contour plots indicated more
accretions near water bodies. Lower thickness towards open water areas may
indicative of recent accretions at the streamside of the landscapes. The thicker
0 a 1 horizon at the inland areas may not be contemporary to the streamside
0a1 horizons. Contour plots for subsurface organic horizons may also carry
the variation in soil formation between landscape positions within the site.
Spatial variation of depth to mineral layer (DML) is a result variation in
deposition when mineral layer was formed. Variations in organic subhorizons
are indicative of previous marsh status, and variations in organic and inorganic
accretions. Sometimes it may be indicative of recent changes in marsh status,
especially for a degrading marsh. Thicker organic layer is indicative of healthy
marsh that can keep up with the local subsidence because of higher accretion
rates. Thin organic layer can indicate degrading marsh experiencing
subsurface erosion at marsh-water interfaces.
At the saline marsh, the DML was shallower near water bodies. Terric
and Typic Medisaprists were delineated based on the organic layer thickness.
Typic Medisaprists occurred mostly toward inland areas and away from open
water at the saline marsh. The DML was shallower in the northeastern half of
the saline marsh where the marsh is degrading. Typic Medisaprists occurred in
the northeastern part of the brackish marsh site, which had thick organic layers
due to presence of thick Oa2 and Oa3 horizons.
233
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
High spatial autocorrelation was found for pH of organic horizons for
saline marsh. However, the pH for the Cg horizon did not show any spatial
autocorrelation. Lower pH was associated with degrading marsh patches
toward the S W and NE corners of the saline marsh. A smooth pH gradient
from NW to SB direction was observed for the Oa3 horizon at the saline marsh.
High spatial variability was found for pH for 0a1 horizon within the brackish
marsh site, with lower pH values along the N W to SB diagonal across the site.
The pH was lower close to open water areas and pH for the Oa3 and Cg
subhorizons did not show any spatial autocorrelation.
Organic/mineral ratio (OM R) data ranged widely for the brackish marsh
compared to saline marsh for all organic subhorizons. More organic matter at
the brackish marsh gave higher OM R compared to the saline marsh. Higher
OMR associated with northern part and lower OMR at southern part of the site
indicated more inorganic accretions (sedimentation) from open water areas.
The high OM R at NE and N W corners of the saline marsh can be attributed to
marsh degradation within this site. The OMR data were highly spatially variable
at the brackish marsh site. Higher O M R was associated with inland indicating
lack of sedimentation.
Spatial variability can be attributed to long-term influence of processes
such as sedimentation, organic accretions and compaction and consolidation.
Localized damages to marshes by hurricane activity and due to marsh
degradation also can cause spatial variability within the marsh. Degradation of
a surface organic layer may result in frequent flooding due to local subsidence.
234
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
The standing water can cause consolidation of sediments within the surface
layer. The consolidation and compaction may be extended into the subsurface
horizons with water activity. Frequent flooding also may provide more
sediment. Understanding of spatial variation of marsh soil characteristics will
help to identify the prominent processes within the marshes and to plan marsh
management strategies.
5.7 References
Barry, R. P., and J. M. Ver Hoef. 1996. Blackbox kriging: Spatial predictionwithout specifying variogram models. J. Agric. Biol, Envtl. Stat. 1(3):297- 322.
Boesch, D. P., Levin, D., Nummedal, D., and Bowles, K. 1983. Subsidence in coastal Louisiana: Causes, Rates, and Effects on Wetlands. U. S. Fish and Wildlife Sen/ice FW S/OBS-83/26, Washington, D. 0 ., 30pp.
Brus, D. J., J. J. De Gruijter, B. A. Marsman, R. Visschers, A. K. Bregt, A. Breeuwsma, and J. Bouma. The performance of spatial interpolation methods and choropleth maps to estimate properties at points: A soil survey case study. Envirometrics 7:1-16.
Cahn, M. D., J. W. Hummel, and B. H. Brouer. 1994. Spatial analysis of soilfertility for site-specific crop management. Soil Sci. Soc. Am. J. 58:1240- 1248.
Childers, D. L., J. W . Day, and R. A. Muller. 1990. Relating climatological forcing to coastal water levels in Louisiana estuaries and the potential importance of El Nino-Southern oscillation events. Climate Research 1:31-42.
Chmura, G. L., R. Costanza, and E. Kosters. 1992. Modelling coastal marsh stability in response to sea level rise: a case study in coastal Louisiana, USA. Ecological Modelling, 64:47-64.
Day, J. W., D. Pont, P. F. Hensel, and C. Ibanez. 1995. Impacts of sea-level rise on deltas in the Gulf of Mexico and the Mediterranean: The importance of Pulsing Events to sustainability. Estuaries 18(4):636-647.
235
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
DeLaune, R. D., C. J. Smith, and W . H. Patrick, Jr. 1983. Relationship of marsh elevation, redox potential, and sulfide to Spartina alterniflora productivity. Soil Sci. Soc. Am. J. 47:930-935.
DeLaune, R. D., J. H. Whitcomb, W. H. Patrick, Jr., J. H. Pardue, and S. R. Pezeshki. 1989. Accretion and canal impacts in a rapidly subsiding wetland. I. ^^^Cs and ^^°Pb techniques. Estuaries 12(4):247-259.
DeLaune, R. D., J. A. Nyman, and W. H. Patrick, Jr. 1994. Peat Collapse, ponding and wetland loss in a rapidly submerging coastal marsh. J. Coastal Res. 10:1021-1030.
Feijtel, T. C., R. D. DeLaune, and W. H. Patrick, JR. 1988. Seasonal pore water dynamics in marshes o f Barataria Basin, Louisiana, Soil Sci. Soc. Am. J. 52:59-67.
Flatman, G. T., and A. A. Yfantis. Geostatistical sampling designs forhazardous waste sites. P.779-801. In L. H. Keith (ed.) Principles of environmental sampling. Secon Edition. Am. Chem. Soc., Washington, DC.
Gamma Design Software. 1994. GS+ Geostatistics for the EnvironmentalSciences Version 2.3 User's Guide. Gamma Design Software, Plainwell, Michigan 49080, USA.
Glazovskaya, M. A. 1968. Geochemical landscapes and types of geochemical soil sequences. Transactions of 9'’’ Int. Congr. Soil Sci. Adelaide. 4:303- 312.
Golden Software Inc. 1995. SURFER for Windows, Version 6 User’s Guide. Golden Software Inc., Golden, Colorado, 80401-1866, USA.
Goovaerts, P. 1997. Geostatistics for natural resources evaluation. Oxford University Press Inc., New York, New York. 483pp.
Gotway, C. A., R. B. Ferguson, G. W. Hergert, and T. A. Peterson. 1996.Comparison of kriging and inverse-distance methods for mapping soil parameters. Soil Sci. Soc. Am. J. 60:1237-1247.
Griffin, T. M., and M. C. Rabenhorst. 1989. Processes and rates ofpedogenesis in some Maryland tidal marsh soils. Soil Sci. Soc. Am. J. 52:59-67.
236
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Haering, K. C., M. C. Rabnhorst, and D. S. Fanning. 1989. Sulfur spéciation in some Chesapeake Bay tidal marsh soils, Soil Sci. Soc. Am. J. 53:862- 870.
Hanna, A. Y ., P. W . Harlan, and D. T. Lewis. 1982. Soil available water as influenced by landscape position and aspect. Agron. J. 74:999-1004.
Hatton, R. S., R. D. DeLaune, and W. H. Patrick, Jr. 1983. Sedimentation accretion, and subsidence in marshes of Barataria Basin, Louisiana. Limnology and Oceanography 28:494-502.
Isaaks, E. H., and R. M. Srivastava. 1989. An introduction to applied geostatistics. Oxford University Press, New York. 561p.
Knotters, M., D. J. Brus, J. H. Oude Voshaar. 1995. A comparison of kriging, co-kriging and kriging combined with regression for spatial interpolation of horizon depth with censored observations. Geoderma 67:227-246.
Krairpanond, N., R. D. DeLaune, and W. H. Patrick, JR. 1992a. Distribution of organic and reduced sulfur forms in marsh soils of coastal Louisiana, Org. Geochem. 18:489-500.
Krairpanond, N., R. D. DeLaune, and W. H. Patrick, JR. 1992b. Sulfur dynamics in Louisiana coastal freshwater marsh soils. Soil Sci. 151(4):261-273.
Lam, N. S. 1983. Spatial interpolation Methods: A review. The American Cartographer 10(2): 129-149.
Lin, C., and M. D. Melville. 1994. Acid sulphate soil-landscape relationships in the Pearl River Delta, southern China, Catena 22:105-120.
Madden, C. J., J. W. Day Jr., and J. M. Randall. 1988. Freshwater and marine coupling in estuaries of the Mississippi River deltaic plain. Amer. Soc. Limnoi. And Oceanogr. 33:982-1004.
McDaniel, P. A., G. R. Bathke, S. W. Buol, D. K. Cassel, and A. L. Falen. 1992. Secondary manganese/iron ratios as pedochemical indicators of field- scale throughflow water movement. Soil Sci. Soc. Am. J. 56:1211-1217.
Nyman, J. A., J. C. Callaway, and R. D. DeLaune. 1993. Case study of a rapidly submerging coastal environment: relationships among vertical accretion, carbon cycling and marsh loss in the terrebone basin, Louisiana. Proceedings of the Hilton Head Island South Carolina USA International Coastal Symposium, June 6-9, 1993. vol 2. 452-457p.
237
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Nyman, J. A., M. Carlose, R. D. DeLaune, and W . H. Patrick, Jr. 1994.Erosion rather than plant dieback as the mechanism of marsh loss in an estuarine marsh. Earth Surface Processes and Landforms 19:69-84.
Nyman, J. A., C. R. Crozier, and R. D. DeLaune. 1995. Roles and patterns of hurricane sedimentation in an estuarine marsh landscape. Estuarine Coastal and Shelf Science 40:665-679.
Reese, R. E., and K. K. Moorhead. 1996. Spatial characteristics of soilproperties along an elevational gradient in aCcarolina Bay wetland. Soil Sci. Soc. Am. J. 60:1273-1277.
Rossi, R. E., D. J. Mulla, A. G. Journel, and E. H. Franz. 1992. Geostatistical tools for modeling and interpreting ecological spatial dependence. Ecological Mongraphs 62(2):277-314.
Smith, J. L., J. J. Halvorson, and R. I. Papendick. 1993. Using multiple-variable indicator kriging for evaluating soil quality. Soil Sci. Soc. Am. J. 57:743- 749.
Salinas, L. M., R. D. DeLaune, and W . H. Patrick, Jr. 1986. Changes occuring along a rapidly submerging coastal area: Louisiana, USA. Journal of Coastal Research 2(3):269-284.
Soil Conservation Service (SCS). 1984. Soil survey of Lafourche Parish,Louisiana. United States Department of Agriculture, Soil Conservation Service. Washington, DC.
Soil Conservation Service (SCS). 1989. East Central Barataria cooperative river basin study, Jefferson, Orleans, Plaquemines and St. Charles Parishes, Louisiana. Rev. May 1989. United States. Soil Conservation Service. National Cartographic Center (U.S.). Ft. Worth, TX : USDA-SCS-National Cartographic Center ; [Alexandria, La. State Conservationist, distributor].
SPSS Inc. 1997. SPSS for Windows Release 8.0.0.
Turner, R. E. 1990. Landscape development and coastal wetland losses in the northern Gulf of Mexico. Amer. Zool. 30:89-105.
Webster, R., and M. A. Oliver. 1989. Optimal interpolation and isarithmic mapping of soil properties. VI. Disjunctive kriging and mapping the conditional probability. J. Soil Sci. 40:497-512.
238
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
CHAPTER 6: CONCLUSIONS
This dissertation presents the soil science investigations for the
multidisciplinary research under the Louisiana NASA/EPSCoR (Experimental
Program to Stimulate Competitive Research) global change research cluster,
which study the fate of carbon and sediments within the Barataria Bay Basin,
Louisiana. This project presents the spatial variability of coastal organic soil
characteristics at different scales. It estimates the spatial variability of pyrite
accumulation to represent variability in the labile carbon pool and the
biogeochemical status of the marsh.
First study presents the ability of assessing seawater influence within the
marsh based on water composition data. The effect of salinity and ionic
competition on affinity of S to roots, and the feasibility of ion exchange resin
strips for water and soil analysis for spatial variability studies are presented in
the second study. Third study presents the pyrite accumulation within the soil
profiles between landscape positions for different marsh types. Spatial
variability is identified and spatial autocorrelation of selected marsh soil
characteristics is presented in the fourth study.
The main objective of the first study is to establish the relationship
between electrical conductivity (EC) and total dissolved solids (TDS) for ground
truthing the Airborne Electromagnetic Profiler data. The relationship, TDS (ppt)
= 0.669 * EC (dS/m) - 0.6208 is recommended for conversion of EC to TDS.
The relationship between EC and the elemental ratios indicate the
seawater influence and deviation of the ratios may be used to determine flow
239
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
direction within marsh for the hydrology work. Barataria Bay estuary has a
chloride dominant water system with a wide range of salinity. The elemental
ratios are similar to that of seawater, which indicates that the water
characteristics of this estuary are extensively under the influence of seawater
intrusion.
Salinity change is mainly due to the dilution effect by mixing with the
fresh water flow. Chloride and SO 4 maintain a linear relationship with EC; Cl
(mg L'1) = 303 + 295 * EC (dS m'^), and SO 4 (mg L'^) = 4.21 + 43.35 * EC (dS
m'^). A significant deviation from this relationship may indicate that the other
processes such as plant uptake or assimilation has changed the water
composition. The CI/SO 4 ratio is about 7.0 for seawater. W ater samples
collected from saline, brackish, and intermediate marsh types maintain a ratio
similar to seawater but fresh marsh had a significantly higher CI/SO 4 ratio
indicating it is independent from seawater influence. Therefore, CI/SO 4 ratio is
proposed to assess the extent of seawater intrusion within the basin.
It is evident from water composition data that Cl dominates the water
system and SO 4 has to compete with Cl as a major anion. Therefore, it is
important to study the influence of Cl and ionic competition on sulfate reduction.
Ion-exchange resins are helpful in understanding the processes by simulating
root uptake. Salinity and Cl significantly reduced the resin extractable sulfate.
This explains a possible reason for accumulating SO 4 within the root zone.
Plants exclude excess soluble salts from uptake as a tolerant mechanism.
240
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Because of high Cl content, SO 4 may have limited affinity to root. This may
accumulate of SO 4 that undergo reduction and form sulfide and pyrite.
Spatial variability studies require an analysis of many samples.
Therefore, a quick method would be very useful to study the spatial variability of
coastal organic soils. Resin strips have been used to measure soil parameters.
However, resins have not been tested for estuarine conditions. This study also
examines the potential use of resins for multi-elemental analysis of estuarine
water and to estimate the sulfur status of coastal organic soils.
Bicarbonate, chloride or phosphate can be used as the terminal anion for
the anion exchange strips. Either 01 concentration or electrical conductivity can
be added to the models to predict elements in water from resin extractable
elements. These procedures and prediction models are recommended for the
Barataria Bay Basin water system and similar chloride dominant estuarine
systems.
Both anion and cation exchange resin strips can be used together for
one sample and 0.5 HOI can be used as the eluent for both resins if the
ICP-AES is used for elemental analysis. This procedure will provide an
alternative to the traditional analytical methods. Equilibration time, elution time
and soil/water ratio needs to be adjusted depending on the S levels and salinity.
The resin extractable S (RES) maintained a linear relationship with water
soluble 8 (W SS) and non-pyritic 8 (NP 8 ) for both mineral and organic soils.
Including pH and Cl concentration as additional variables helped to obtain
better models to predict NP 8 and W 8 8 , especially for organic soils. Separation
241
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
of mineral horizons and organic horizons improved the regression coefficients
for individual models when compared to the overall model using for both soil
horizons. Therefore, better prediction can be achieved using different models
for different soil horizons. Sulfur mineralization is a limitation reported in other
studies for resin use in 8 analysis, which may be the main cause of low for
prediction models. However, the models are able to predict over 70 % of the
variation despite the variations in marsh types, salinity, chloride, organic/mineral
ratio and pH. Resin extractable 8 can be suggested to estimate non-pyritic 8
and water soluble 8 for spatial variability studies.
Each marsh type occurs within a certain range of salinity depending on
the salt tolerance ability of its vegetation. Pyrite accumulation and sulfate
reduction may be different between the marsh types because of the salinity
differences and associated changes in 8 O4 content and the competition
between 8 O4 and Cl. As indicated by the resin study, salinity and 01 influence
sulfate reduction because of the ionic competition between 8 O4 and 01,
however, this effect may be lowered at low salinity levels. Effect of landscape
position and salinity level on pyrite accumulation is studied because of the
reported accretion differences between streamside and inland within the marsh
landscape.
Organic layers comprise distinctly different subhorizons within the soil
profiles and the number of subhorizons is variable. The surface horizons at
streamside represent the recent accretions, which may be younger than the
surface horizons inland. Erosion and re-deposition of organic soil material may
242
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
create wide spatial variability within a degrading marsh. Depth to mineral layer
indicates considerable spatial variation, especially at the brackish marsh site.
Deeper DML may represent depressions formed due to differences in
deposition when the mineral layer was formed.
Soil BD is lower for the brackish marsh compared to the saline marsh.
Lack of sediment feeding into the brackish marsh may be the reason for the
iower BD. More mineral amounts may stabilize the BD in saline areas. The BD
varies highly within the organic layer of the brackish marsh while it is uniform at
the saline marsh. High salinity can increase higher sedimentation due to
enhanced flocculation.
Salinity profiles differ between landscape positions when the inland
position is landlocked. This difference may be pronounced in more saline
areas. Evapotranspiration and lack of lateral flow (due to hydrological barriers)
may change the salinity profiles inland as compared to streamside. When small
streams flow through the marsh, the hydrological barriers are broken and
salinity differences disappear. Biogeochemical differences may result from this
salinity variation within the landscape. Therefore, understanding the spatial
variability of salinity is important when monitoring the marsh status within an
area.
Salinity influences pyrite accumulation, however, its influence varies
within the profile. Pyrite content within the surface horizon is significantly
different between landscape positions. There is no evidence of differences
between marsh types because the balance between pyrite formation and
243
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
oxidation mainly controls pyrite content within the surface horizons. Pyrite
content within the inland surface organic layers is lower compared to the
streamside, especially when the inland is landlocked. The landscape position
effect on pyrite accumulation dramatically diminishes deeper in the soil profile
but marsh type effect is prominent. This may indicate the salinity effect on
pyrite accumulation along the salinity gradient. The higher the marsh salinity
the higher the pyrite accumulation within a soil horizon. The highest pyrite
accumulation is observed within the thin layer of dark organic material that
occurred immediately above the mineral layer. This may represent the marine
environment when it was formed.
The non-pyritic Fe contents are significantly different between the
landscape positions within the more saline marshes (i.e., saline and brackish
marshes), suggesting that inland lacks sedimentation. The intermediate marsh
contains significantly lower non-pyritic Fe within surface organic layers
compared to other marshes. This may not be related to the salinity but to the
status of the marsh. The intermediate marsh at this location is extensively
broken-up (less than 50% vegetation cover). The non-pyritic Fe content can be
a suitable indicator to assess marsh status. When landlocked, inland positions
can retain more non-pyritic Fe within sub surface organic layers due to limited
pyritization, otherwise the non-pyritic Fe can be flushed away.
Non-pyritic S content within the organic sub horizons differs significantly
between marsh types due to salinity differences. More saline marshes contain
more non-pyritic S while less saline marshes are limited by the S supply. The
244
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
brackish marsh inland contains more non-pyritic S within the profile compared
to the streamside. This suggests that when the inland is not landlocked, non-
pyritic S accumulate within the profile. This is similar to the reason suggested
by the resin study. Subsurface organic horizons within the profiles of less
saline areas are S limited as also indicated by the water composition data.
Soil pH differences are more pronounced between marshes than the
landscape positions. The pH does not vary within the organic layer. The
mineral layer always has higher pH compared to the organic subhorizons,
which may represent the saline (marine) environment under which it was
formed. The surface horizon pH differs significantly between less saline
marshes and more saline marshes. Landscape difference is found only at the
intermediate marsh where the marsh is extensively degrading. The pH of the
mineral layers of less saline marshes is significantly lower compared to the
saline marshes.
Pyrite framboids are detected within the saline marsh sediments using
scanning electron microscopy. The framboids are 6 to 8 pm in diameter and
are found in close association with the organic material. Both the saline and
brackish marsh sediments contain mixed mineralogy with smectite, illite, and
kaolinite clays. Pyrite is evident within the sediments for both marshes with
coarser fractions ( < 2 0 pm) containing more pyrite.
There is a considerable amount of reduced S compounds accumulated
within these soil profiles, which occur as pyritic and non-pyritic S. These
organic soils should be reclassified to indicate sulfidic materials within their
245
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
profiles. The technique used to estimate pyrite and non-pyritic S can be
adopted as a method to characterize sulfidic material within these soils.
Soil morphology and biogeochemical status is variable within the
landscape as shown in the previous study. This study estimates the spatial
autocorrelation for several coastal organic soil characteristics within a saline
and a brackish marsh at a larger scale. This information is required for planning
future marsh sampling schemes as well as understanding the spatial variability
pattern of marsh soils within the landscape.
Variation of subhorizon thickness is greater at depths within the profile
and shows high spatial autocorrelation that follows semivariograms represented
by spherical models. Accretion differences within the landscape may be the
major source of variability of soil morphology within these sites. Contour plots
indicated more accretion near water bodies. Lower thickness within open water
bodies may be due to consolidation of sediments by the standing water.
Contour plots for subsurface organic horizons may indicate a historical
signature of marsh status in the past. Spatial variation of DML is a result of
variations in differences in deposition at mineral layer formation, which is
associated with organic subhorizon thickness variation. Thicker DML is
indicative of healthy marsh that could counter the local subsidence because of
higher accretion rates. Thin DML may indicate degrading marsh that also may
be experiencing subsurface erosion, or consolidation of sediments.
Terric and Typic Medisaprists are delineated based on the organic layer
thickness. Typic Medisaprists occur mostly toward inland areas and away from
246
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
open water and streams for the saline marsh. The DML is shallower in the
northeastern half of the saline marsh where the marsh is degrading. Typic
Medisaprists occur in the northeastern part of the brackish marsh site, which
had thick organic subhorizons.
High spatial autocorrelation is found for pH within organic subhorizons of
the saline marsh. However, the pH of the Cg horizon does not show any spatial
autocorrelation. Lower pH is associated with degrading marsh patches toward
the SW and NE corners of the saline marsh. A smooth pH gradient from NW to
SE direction is observed for the subhorizons within the saline marsh. High
spatial variability is found for pH for the surface organic subhorizons within the
brackish marsh site, with lower pH values along the N W to SE diagonal across
the site. The pH is lower close to open water areas and pH for the organic
subhorizons and mineral horizon does not show any spatial autocorrelation.
Organic/mineral ratio (OMR) data ranges widely for the brackish marsh
compared to saline marsh for all organic subhorizons. More organic matter for
the brackish marsh give higher OMR compared to the saline marsh. Higher
O M R associated with the northern part and lower OM R at the southern part of
the site indicates more inorganic accretions (sedimentation) from the open
water. The high OM R at the NE and N W corners of the saline marsh can be
attributed to marsh degradation within this site. The OMR data are highly
spatially variable for the brackish marsh site. Higher OM R is associated with
the inland marsh indicating lack of sedimentation.
247
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
VITA
Langappulige Cecil Dharmasri was born on August 8, 1961, in Matara,
Sri Lanka. He was raised in Matara, where he graduated from St. Servatius
College in 1980. He received his bachelor of science degree in Agriculture from
Faculty of Agriculture, University of Peradeniya, Sri Lanka, in 1984 specializing
in Soil Science as undergraduate major.
He worked for the Department of Agriculture as a Research Officer from
1985 to 1992. He was stationed at the Regional Agricultural Research Center,
Angunakolapelessa, Sri Lanka. His work involved applied and adaptive
research in Agronomy, Soil Science and Cropping Systems. Cecil received a
scholarship from International Development Research Center, Canada, to study
for his masters in 1992. He obtained his master of science degree in Soil
Science from the Department of Soil Science, University of Saskatchewan,
Canada, in 1995. His research focussed soil-plant-water relations for semiarid
conditions in Canada and Sri Lanka and worked under the supervision of Dr. E.
deJong.
Cecil started his doctoral program in the Department of Agronomy at
Louisiana State University in 1995, under the supervision of Dr. W ayne H.
Hudnall. Cecil's dissertation research is part of the Louisiana NASA/EPSCoR
Global Change research program. He majored in Soil Science with emphasis in
mapping sciences. Cecil is a member of Sigma Xi, Gamma Sigma Delta, Soil
Science Society of America, American Society of Agronomy, Soil and W ater
Conservation Society, Clays and Clay Minerals Society, Soil Science Society of
248
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
Sri Lanka, Sri Lanka Association for the Advancement of Sciences,
International Erosion Control Association, and the International Soil Science
Congress.
Cecil met Ayesha when he was working at Angunakolapelessa and they
got married in 1990. His elder son, Poorna, was born in 1991 and the younger
son, Chamara, was born in 1996. He lived with his wife and two sons in Baton
Rouge. Cecil accepted a position as a Post Doctoral Fellow at Zeneca Ag
Products, Western Research Center, California.
249
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
DOCTORAL EXAMINATION AND DISSERTATION REPORT
Candidate: L. Cecil Dharmasri
Major Field; Agronomy
Title of Dissertation: Spatial Variability of Coastal Organic SoilCharacteristics
Approved:
Date of Examination:
May 4. 1998
Major'Professer and Chairman
Dean of the Graduate School
EXAMINING COMMITTEE:
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
IMAGE EVALUATION TEST TARGET (Q A -3 )
y/l
/
1.0
l . l
[ f i a IIIIM
: l~ ilia I lia
mil 1.8
1.25 1.4 1.6
15 0 m m
V
>■*
V
O /
' / y
x 4 P P l_ IE D A I IV W G E , In c_ = 1653 East Main Street
' Rochester, N Y 14609 USA Phone: 716/482-0300
- = - - ^ = Fax: 716/288-5989
O 1993. Applied Image, Inc.. Ail Rights Reserved
Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.