Sony VPL-VW600ES Quick Reference

7/26/2019 Sony VPL-VW600ES Quick Reference

1/19

Quick Reference Manual

Before operating the unit, please read this manual thoroughly and retain it for

future reference.

VPL-VW600ESVPL-VW350ES

4-485-164-02(1)

Video Projector

2013 Sony Corporation Printed in Japan


2/19

2

This Quick Reference Manual explains the installation and basic operations for projectingpictures. It also describes important notes and cautions to which you have to pay attention whenhandling and using this unit.

Refer to Warning Indicators and Replacing the Lamp, as necessary.For details on the operations, refer to the Operating Instructions contained in the supplied CD-ROM.

About the Quick Reference Manual

Preparing ....................................................Page 8

Installing the Unit....................................Page 9

Connecting the Unit.............................Page 11

Selecting the Menu Language ........Page 12

Projecting..................................................Page 13

Error Handling Warning Indicators.........................................Page 15

Maintenance Replacing the Lamp .......................................Page 16

Step 1

Step 2

Step 3

Step 4

Step 5


3/19

3

WARNING

To reduce the risk of fire or electricshock, do not expose this apparatusto rain or moisture.To avoid electrical shock, do not openthe cabinet. Refer servicing toqualified personnel only.

WARNINGTHIS APPARATUS MUST BEEARTHED.

WARNINGWhen installing the unit, incorporate areadily accessible disconnect device in the

fixed wiring, or connect the power plug to aneasily accessible socket-outlet near the unit.If a fault should occur during operation ofthe unit, operate the disconnect device toswitch the power supply off, or disconnectthe power plug.

CAUTIONAbout the LAN connectorFor safety, do not connect the connector forperipheral device wiring that might have

excessive voltage to this port.

For the customers in the U.S.A.This equipment has been tested and found tocomply with the limits for a Class B digitaldevice, pursuant to part 15 of the FCC Rules.These limits are designed to providereasonable protection against harmfulinterference in a residential installation. Thisequipment generates, uses and can radiate

radio frequency energy and, if not installedand used in accordance with the instructions,may cause harmful interference to radiocommunications. However, there is noguarantee that interference will not occur ina particular installation. If this equipmentdoes cause harmful interference to radio ortelevision reception, which can bedetermined by turning the equipment off andon, the user is encouraged to try to correctthe interference by one or more of the

following measures:- Reorient or relocate the receiving antenna.

- Increase the separation between theequipment and receiver.

- Connect the equipment into an outlet on acircuit different from that to which thereceiver is connected.

- Consult the dealer or an experiencedradio/TV technician for help.

You are cautioned that any changes ormodifications not expressly approved in thismanual could void your authority to operatethis equipment.

All interface cables used to connectperipherals must be shielded in order tocomply with the limits for a digital devicepursuant to Subpart B of part 15 of FCCRules.

If you have any questions about this product,you may call;Sony Customer Information Service Center1-800-222-7669 or http://www.sony.com/

This device complies with part 15 of theFCC Rules. Operation is subject to thefollowing two conditions: (1) This devicemay not cause harmful interference, and (2)this device must accept any interferencereceived, including interference that maycause undesired operation.

This device and its antenna(s) must not beco-located or operating with any other

Declaration of ConformityTrade Name: SONYModel: VPL-VW600ES

VPL-VW350ESResponsible party: Sony Electronics Inc.

Address: 16530 Via Esprillo,San Diego, CA 92127U.S.A.

Telephone Number:858-942-2230

This device complies with part 15 of theFCC Rules. Operation is subject to thefollowing two conditions: (1) This devicemay not cause harmful interference, and(2) this device must accept any interferencereceived, including interference that maycause undesired operation.


4/19

4

antenna or transmitter except Grantcondition.

This Equipment complies with FCCradiation exposure limits set forth for anuncontrolled environment and meets theFCC radio frequency (RF) Exposure

Guidelines. This equipment has very lowlevels of RF energy that are deemed tocomply without testing of specificabsorption rate (SAR).

Caution on replacement/disposal ofthe battery for the 3D glassesDanger of explosion if battery is incorrectlyreplaced.Replace only with the same or equivalenttype recommended by the manufacturer.

When you dispose of the battery, you mustobey the law in the relative area or country.

Precautions

On safety Check that the operating voltage of your

unit is identical with the voltage of your

local power supply. Should any liquid or solid object fall into

the cabinet, unplug the unit and have itchecked by qualified personnel beforeoperating it further.

Unplug the unit from the wall outlet if it isnot to be used for several days.

To disconnect the cord, pull it out by theplug. Never pull the cord itself.

The wall outlet should be near the unit andeasily accessible.

The unit is not disconnected to the ACpower source (mains) as long as it isconnected to the wall outlet, even if theunit itself has been turned off.

Do not look into the lens while the lamp ison.

Do not place your hand or objects near theventilation holes. The air coming out ishot.

On preventing internal heat build-upAfter you turn off the power with the ?/1(ON/STANDBY) button, do not disconnectthe unit from the wall outlet while thecooling fan is still running.

CautionThis unit is equipped with ventilation holes(intake) and ventilation holes (exhaust). Do

not block or place anything near these holes,or internal heat build-up may occur, causingpicture degradation or damage to the unit.

On repackingSave the original shipping carton andpacking material; they will come in handy ifyou ever have to ship your unit. Formaximum protection, repack your unit as itwas originally packed at the factory.

For the customers in the U.S.A.SONY LIMITED WARRANTY- Pleasevisit http://www.sony.com/psa/warrantyfor important information and completeterms and conditions of Sonys limitedwarranty applicable to this product.

For the customers in CanadaSONY LIMITED WARRANTY- Pleasevisit http://www.sonybiz.ca/solutions/Support.do for important information andcomplete terms and conditions of Sonyslimited warranty applicable to this product.

For the customers in EuropeSony Professional Solutions Europe -Standard Warranty and Exceptions on

Standard Warranty.Please visit http://www.pro.sony.eu/warranty for important information andcomplete terms and conditions.

For the customers in KoreaSONY LIMITED WARRANTY- Pleasevisit http://bpeng.sony.co.kr/handler/BPAS-Start for important information andcomplete terms and conditions of Sonyslimited warranty applicable to this product.


5/19

5

On watching 3D video images

Safety precautions You should only use the 3D glasses for

watching 3D video images. If you observe flickering or flashing, turn

off the lighting in the room.

Not for use by children without properadult supervision.

Be careful not to pinch your fingers inhinges of the 3D glasses when bending thetemple frames.

Do not drop or modify these 3D glasses. If these glasses are broken, keep broken

pieces away from your mouth or eyes.

On LCD Projector

The LCD projector is manufactured usinghigh-precision technology. You may,however, see tiny black points and/or brightpoints (red, blue, or green) that continuouslyappear on the LCD projector. This is anormal result of the manufacturing processand does not indicate a malfunction.Also, when you use multiple LCD projectorsto project onto a screen, even if they are ofthe same model, the color reproductionamong projectors may vary, since colorbalance may be set differently from oneprojector to the next.

On condensationIf the room temperature where the projectoris installed changes rapidly, or if theprojector is moved suddenly from a cold to awarm place, condensation in the projectormay occur. As the condensation may causemalfunction, be careful in adjusting

temperature settings of the air conditioner. Ifcondensation occurs, leave the projectorturned on for about two hours before use.

SONY WILL NOT BE LIABLE FORDAMAGES OF ANY KINDRESULTING FROM A FAILURE TOIMPLEMENT PROPER SECURITYMEASURES ON TRANSMISSIONDEVICES, UNAVOIDABLE DATALEAKS RESULTING FROMTRANSMISSION SPECIFICATIONS,OR SECURITY PROBLEMS OF ANYKIND.


6/19

6

Notes on Installationand Usage

Do not place the unit in the followingsituations, which may cause malfunction ordamage to the unit.

Near wallsTo maintain the performance and reliabilityof the unit, leave space between walls andthe unit as illustrated.

Air from air conditioners or the ventilationholes of this unit or other devices, may causeoscillation on the screen. Be sure not toinstall this unit in the area where the air fromair conditioners or the ventilation holes ofthese devices reach to the front side of thisunit.

Poorly ventilated location

Leave space of more than 30 cm (117/8

inches) around the unit.

Hot and humid

Locations subject to direct cool orwarm air from an air-conditionerInstalling the unit in such a location maycause a malfunction of the unit due tomoisture condensation or rise intemperature.

Near a heat or smoke sensorMalfunction of the sensor may occur.

Very dusty and extremely smokylocations

Do not do any of the following while usingthe unit.

Tilting front/rear and left/rightAvoid using the unit tilted at an angle ofmore than 15 degrees.

Unsuitable installation

1 cm (13/32inch)

30 cm

(11 7/8

inches)

30 cm

(11 7/8

inches)

15 cm

(6 inches)30 cm

(11 7/8

inches)

30 cm

(11 7/8

inches)

Unsuitable Conditions


7/19

7

Do not install the unit anywhere other thanon a level surface or on the ceiling. Installingthe unit in such a location may result inuneven color uniformity or reduce thereliability of the effects of the lamp.If the unit is tilted up or down, the image onthe screen may be trapezoidal.

Position the unit so that the lens is parallel tothe screen.

When installing the unit at highaltitudesWhen using the unit at an altitude of1,500 m (approx. 4,900 ft) or higher, set

Cooling Setting on the Setup menu toHigh. Failing to set this mode when usingthe unit at high altitudes could have adverse

effects, such as reducing the reliability ofcertain components.

Never mount the projector on the ceiling

or move it by yourself. Be sure to consultwith qualified Sony personnel (charged).

When installing the unit on a ceiling, besure to use a safety wire, etc., to preventthe unit from falling. Entrust theinstallation to an experienced contractor orinstaller.

For dealers When the projector is mounted on the

ceiling, a Sony bracket or recommendedequivalent must be used for installation.

Be sure to secure the cabinet cover firmlywhen installing to the ceiling firmly.

15 or more

15 ormore

15 or more

15 ormore

15 or more

Safety precautions forinstalling the unit on a ceiling


8/19

8

Check the carton to make sure it contains thefollowing items: Remote control (1)

VPL-VW600ES: RM-PJ24VPL-VW350ES: RM-PJ28

Size AA (R6) manganese batteries (2) Lens cap (1)

When you purchase the projector, a lenscap is on the lens. Remove the lens capbefore you use the projector.

AC power cord for the projector (1)

Quick Reference Manual (this manual) (1) Operating Instructions (CD-ROM) (1)

CAUTIONDanger of explosion if battery is incorrectlyreplaced.Replace only with the same or equivalenttype recommended by the manufacturer.When you dispose of the battery, you mustobey the law in the relative area or country.

Installing batteriesTwo size AA (R6) batteries are supplied forRemote Control.To avoid risk of explosion, use size AA (R6)

manganese or alkaline batteries.

Caution about handling the remotecontrol Handle the remote control with care. Do

not drop or step on it, or spill liquid of anykind onto it.

Do not place the remote control in alocation near a heat source, a place subjectto direct sunlight, or a damp room.

The manual can be read on a computer withAdobe Reader installed.You can download Adobe Reader free fromthe Adobe website.

1 Open the index.html file in the CD-ROM.

2 Select and click on the manual thatyou want to read.

If you have lost or damaged the CD-ROM, you

can purchase a new one from your Sony dealer

or Sony service counter.

PreparingStep 1

Checking the SuppliedAccessories

Inserting the Batteries intothe Remote Control

Push and slide toopen.

Insert the batteries Eside first.

Using the CD-ROM manual

Note


9/19

9

1 Position the unit so that the lens isparallel to the screen.

2 After connecting the AC power cord tothe unit, plug the AC power cord intoa wall outlet.

3 Press the ?/1(ON/STANDBY) buttonto turn on the unit.

4 Project an image on the screen, thenadjust the focus, size, and position.

VPL-VW600ES

a Adjust the focus.Press the LENS ADJUSTMENT(FOCUS) button to display the LensFocus adjustment window (test pattern).

Then adjust the focus of the picture bypressing the M/m/


10/19

10

proper position of the picture bypressing the M/m/


11/19

11

When making connections, be sure to do the following: Turn off all equipment before making any connections. Use the proper cables for each connection. Insert the cable plugs properly; poor connection at the plugs may cause a malfunction or poor

picture quality. When pulling out a cable, be sure to pull it out from the plug, not the cableitself.

Refer to the operating instructions of the connected equipment.

Connecting the UnitStep 3

Right side of the unit

AV amplifier Speakers

Equipment with HDMIoutput connectors

Computer

to HDMI output

HDMI cable (not supplied)

: Video signal flow Use a high speed HDMI cable on which the cable type logois specified. (Sony products are recommended.)

For more information, refer to Connections andPreparations in the Operating Instructions contained inthe supplied CD-ROM.


12/19

12

You can select the language for displayingthe menu and other on-screen displays. Thefactory default setting is English. To changethe current menu language, set the desired

language with the menu screen.

1 Press MENU.

The menu appears.

2 PressM/mto select the Setupmenu, and press,or .

The setting items of the selected menu

appear.

3 PressM/mto select Language, andpress,or .

4 PressM/m/


13/19

13

1 Turn on both the unit and theequipment connected to the unit.

2 Press INPUT to display the inputpalette on the screen.

3 Select the equipment from which youwant to display images.

Press INPUT repeatedly or press M/m/(enter) to select the equipment from

which to project.

1 Press the ?/1(ON/STANDBY)button.

A message POWER OFF? appears onthe screen.

2 Press the ?/1(ON/STANDBY) buttonagain before the message disappears.

The ON/STANDBY indicator flashes ingreen and the fan continues to run toreduce the internal heat.

The fan stops and the ON/STANDBYindicator changes from flashing green toremaining red.

The power is turned off completely, and youcan disconnect the AC power cord.

Never disconnect the AC power cord while the

indicator is flashing.

You can turn off the unit by holding the ?/1(ON/STANDBY) button for about 1 second,

instead of performing the above steps.

ProjectingStep 5

Projecting the Picture

Turning Off the Power

Example: To view the picture from thevideo equipment connected to the HDMI1 connector of this unit.

Note

For more information, refer toProjecting in the Operating Instructionscontained in the supplied CD-ROM.


14/19

14

Press one of the CALIBRATED PRESETbuttons.

Selecting the Picture Viewing Mode

CALIBRATEDPRESET buttons

Setting items Description

CINEMA FILM 1 Picture quality suited to reproducing the highly dynamic and

clear images typical of master positive film.

CINEMA FILM 2 Picture quality suited to reproducing the rich tone and colortypical of a movie theater, based on the tones changed for FILM1.

REF A picture quality setup suitable for when you want to reproducefaithfully the original image quality, or for enjoying imagequality, without any adjustment.

TV Picture quality suited for watching TV programs, sports,concerts, and other video images.

PHOTO Ideal for projecting still images taken with a digital camera.

GAME Picture quality suited to gaming, with well-modulated colorsand fast response.

BRT CINE Picture quality suited for watching movies in a brightenvironment, such as a living room.

BRT TV Picture quality suited for watching TV programs, sports,concerts, and other video images in a bright environment, suchas a living room.

USER Adjusts the picture quality to suit your taste then saves the

setting. The factory default setting is the same as REF.

For more information, refer to Projecting in theOperating Instructions contained in the supplied CD-ROM.


15/19

15

The ON/STANDBY or WARNING indicator lights up or flashes if there is any trouble withyour projector.

When a warning indicator other than the above starts flashing, and the symptom persists even after

carrying out the above methods, consult with qualified Sony personnel.

Error Handling

Warning Indicators

Flashing/Lighting indicators The number offlashes

Cause and Remedy

Twice Close the lamp cover securely, then tightenthe screws securely.

Three times The temperature of lamp is unusually high.Turn off the power and wait for the lamp tocool, then turn on the power again.If the symptom persists, the lamp may be at

the end of its service life. In this case,replace the lamp with a new one.

Twice The internal temperature is unusually high.Check to ensure that if nothing is blockingthe ventilation holes or whether or not theunit is being used at high altitudes.

Three times The fan is broken. Consult with qualifiedSony personnel.

Note

ON/STANDBYindicator WARNING

indicator

(Flashes in red)

(Flashes in red) (Flashes in red)

Both indicators flash

If there is any problem or an error message appears on thescreen, refer to Error Handling in the OperatingInstructions contained in the supplied CD-ROM.


16/19

16

The lamp used for the light source has acertain lifespan. When the lamp dims, thecolor balance of the picture becomesstrange, or Please replace the Lamp.appears on the screen, the lamp may beexhausted. Replace the lamp with a new one(not supplied) without delay.

TipThe lifespan of the lamp used for the light

source changes depending on the installation

environment or use conditions. You can use thelamp longer by avoiding turning the lamp off

until several minutes pass after turning the

lamp on.

Tools you need to get started: Projector Lamp (Optional)

VPL-VW600ES: LMP-H260VPL-VW350ES: LMP-H230

Standard Phillips screwdriver Cloth (for scratch protection)

Caution The lamp remains hot after the unit is

turned off with the ?/1(ON/STANDBY)button. If you touch the lamp, you mayburn your fingers. When you replace thelamp, wait for at least 1 hour for the lampto cool.

Do not touch the surface of the lamp. Ifyou touch it, wipe off the fingerprints with

a soft cloth. Pay special attention to replacing the lampwhen the unit is installed on the ceiling.

When replacing the lamp of a unit which ison the ceiling, do not stand directly underthe lamp cover. When removing the lampdoor (inner cover), avoid twisting it. If thelamp explodes, fragments may causeinjury.

When removing the lamp unit, make sureit remains horizontal, then pull straight up.

Do not tilt the lamp unit. If you pull out thelamp unit while tilted and if the lampbreaks, the pieces may scatter, causinginjury.

Be sure to use a specified projector lamp for

the replacement. If you use lamps other than

the specified projector lamp, the unit may

malfunction.

Be sure to turn off the unit and unplug the

power cord before replacing the lamp, then

check the ON/STANDBY indicator has

already been turned off.

1 Turn off the unit and unplug the ACpower cord.

2 When setting the unit on a flat surfacesuch as a desk etc., put a cloth toprevent the surface from beingscratched. Place the unit on the cloth.

Be sure that the unit is placed on a stable

surface.

3 While pressing the part indicatedin the lamp cover illustration, slide1and then open2the lamp cover.

4 Loosen the lamp door (inner cover)screw with a Phillips screwdriver, andthen open the lamp door.

Maintenance

Replacing the Lamp Notes

Note


17/19

17

5 Loosen the 3 screws on the lamp withthe Phillips screwdriver. Hold up the

handle, then pull the lamp straight out.

Do not loosen other screws except the 3

specified screws.

Hold the lamp by the handle to remove

and attach it.

6 Push in the new lamp by the handlesecurely until it reaches the end, andthen tighten the 3 screws.

Be careful not to touch the optical blockinside the unit.

7 Close the lamp door (inner cover), andthen tighten the screw.

8 Close the lamp cover.

Notes

Handle

Note


18/19

18

9 Wipe dust off the ventilation holes(intake) with a soft cloth.

10Turn on the unit, then select the lampsetting item on the Setup menu.

The menu screen below will beappeared.

TipIf Settings Lock is set to Level B, set to

Off once.

11Select Yes.

CautionDo not put your hands into the lampreplacement slot, and do not allow any liquidor other objects into the slot to avoidelectrical shock or fire.

The unit will not turn on unless the lamp is

securely installed in place.

The unit will not turn on unless the lamp

cover are securely closed.

To clear a message displayed on the screen,

press any button either on the remote control

or the control panel of the unit once.

Note on replacing the lamp whenbroken, in the case of a ceilinginstallationIf the lamp breaks, broken lamp pieces mayscatter and cause injury.When the unit is on the ceiling, remove thelamp door (inner cover) by sliding ithorizontally slowly after raising it with 30degree opened. Avoid twisting the lamp door(inner cover).

Disposal of the used lamp

For the customers in the USA

Lamp in this product contains mercury.Disposal of these materials may beregulated due to environmentalconsiderations. For disposal orrecycling information, please contactyour local authorities or theTelecommunications IndustryAssociation (www.eiae.org).

Notes

Ventilation holes(intake)

NoteThe lamp contains mercury. The disposal

rules for used fluorescent tubes depend on

where you live. Follow the waste disposal

policy in your area.


19/19

Mettre disposition de la lampeusage

Pour les clients aux tats-UnisLa lampe dans ce produit contient dumercure. La disposition de cesmatriaux peut tre rglemente suite

des considrations environnementales.Pour obtenir des informations dedisposition ou de recyclage, veuillezcommuniquer avec vos autorits localesou la Telecommunications IndustryAssociation (www.eiae.org).

Documents

Sony VPL-VW600ES Quick Reference