Upload
saptagunung
View
70
Download
10
Embed Size (px)
DESCRIPTION
CAM Software information
Citation preview
SolidCAM2014 SP4 Release Notes
Author: Anna Abelentsev
Written: February 01, 2015
Page 1 of 5 Last updated: February 5, 2015
General 31816 Preview of CAM-part is missing in SW2015 Fixed
31778 "V" sign is missing when mac1-1 position created automatically while creating new part
Fixed
31685, 31315, 31680, 30385, 31048
Envelope problems Fixed
28588 Vericut: Wrong position of fixture in MAC2 Fixed
31730 "Save as" doesn't work for files with non-unicode letters in name of features Fixed
31762 SolidCAM symbol instead of the model picture in Browse Recent Parts UI Fixed
31768 "Send to" doesn't work in Win8 Fixed
31441 User-defined parameter description in the operation GUI Implemented
31599 Small bug in operation names (rename to default from user-defined prefix) Fixed
30795 Part definition dialog - buttons are overlapped by each other. Fixed
31873 Can't open internal part ("Open" button is disabled) Fixed
31941 Wrong fixture name displayed in Setup interface after CAM-part clean up Fixed
CoordSys
29538 CoordSys Definition defaults using Metric values in Inch mode Fixed
31761 Delete several CoordSys in one step is impossible, if you select MAC and not position
Fixed
G-code
31792 @m_feed_spin is abcent in pcode for Chamfer recognition operation Fixed
31586 wrong C angle output in Drilling around 4x Fixed
31699 HSS operation generates @rapid_line and @line instead of @move_5x and @line_5x
Fixed
31849 Turning: garbage in slave_ytool parameter in trace Fixed
31904 Change bit for spin isn't correct Fixed
31879 xtopos cordinate is incorrect for wrapped operation Fixed
31650 ive operation name as default G-code file name when generate G-code from Cam-tree
Implemented
28243 Calculate feed rate according to diameter in @line_4x for pos_to_machine = Y also
Fixed
31706 inverse_feed is wrong in @line_5x in wrapped 2.5D Fixed
31583 Duplicated approach movements for open chains Fixed
31875 Set coordinats tocenter and tostart are wrong in threading operation Fixed
31845 Changes in @rotate_to_plane for head-table kinematics Fixed
31301 Wrong B_angle on Back Spindle Fixed
Release notes
Page 2 2/5/2015
Geometry
31825 Geometry with offset turns big arcs into lines. Fixed
iMachining
31654 3DiMachining: When Synchronize the changes - delta is taken into account and changes the depth
Fixed
31820 Crash in "show 3D" option in iMachining operation Fixed
31595, 31598 Incorrect message in iMachining operation during calculation Fixed
31789 Spring Pass doesn't work in iFinish Fixed
31745, 31741, 31758
Crash with stock on Rapid move(G0) Fixed
30718 Tool thin wall during iMachining => tool is damaged Fixed
31468 Approach toolpath is performed twice Fixed
31653 iFinish is not possible on Haas machine due to wrong arc sizes. Fixed
31717 Gouge with target during machining with compensation Fixed
2.5D Milling
31689 Broaching: GCode and Simulate are wrong Fixed
31906 Contour 3D: During cutting tool jumps to Clearance level Fixed
28481 Multiple wall finish in Pocket. Implemented
30200 Grey out unnecessary fields in profile/pocket -> chamfer Implemented
31675 Extra lines in threading operation's toolpath Fixed
31603 Handling of small arcs in rough toolpath in Profile operation with compensation Fixed
31656 Helical LeadIn is missing after CAM-part reload Fixed
31601 Helical profile without last flat step -> bad toolpath Fixed
31818 Impossible to calculate drilling operation with shaped tool Fixed
31851 Variable depth: When Synchronize the changes - delta is taken into account and changes the depth
Fixed
31568 Wrong STL holder orientation in Drilling operation Fixed
31619 Contour 3D operation is not calculated, but Simulation option is available Fixed
31578 4x indexial field behavior is opposite in Drill and HSS operations in positions.(HEAD-HEAD)
Fixed
31669 Calculation of simple slot failed Fixed
31337 tool goes into the material in Spiral Pocket operation Fixed
Release notes
Page 3 2/5/2015
3D Milling 31953, 31942, 31944, 31937, 31734, 31563, 31348, 31080, 31709, 31624, 31710 3D Milling: Constant-Z toolpath problems Fixed
31826 Crash during calculation of 3D Milling Fixed
31344 Tool gouges into material if manual working area is used Fixed
31342 Rapid move through the whole part Fixed
31607 Repositioning: G0 through clearance OR G1 on safety distance from surface. Implemented
31878 Offset cutting: Toolpath is not complete Fixed
31891 Get a lot of lines instead of arc in 3D Milling Linear operation Fixed
31913 Needless movements to clearance in 3D Engraving Fixed
HSR/HSM 31039 Minimum Tool length is not calculated Fixed
31383 Offset cutting: Step over doesn't work according to the definition Implemented
29342 Integrating MS15 into SolidCAM2014 Implemented
HSS 28884 No 4x option in motion control if work with MACx-positionN. Implemented
5x simultaneous
31853 Port machining: SolidCAM crashes when uncheck "Check against machine surface" Fixed
31696, 31428 Multiblade machining: option to work on rest material doesn't save it's state Fixed
28159 Changes in geometry selection and gouge check options names Implemented
30597 Multiblade: Roughing does not respecting settings of incomplete layers and Rest Material Fixed
30490 5x prefix for operation 4x Fixed
Release notes
Page 4 2/5/2015
AFRM 31719 AHRM: Crash when close CAM-part after "add machine" action Fixed
31376 AHRM: Flat drill holes are not recognized Fixed
31050 AHRM: Badly Placed Home Positions ( Set " in CoordSys #1 origin" by default ) Fixed
31936 Pocket recognition: Rest material toolpath is not complete Fixed
31837 Pocket recognition: Toolpath doesn't follow the Geometry Fixed
31615 Pocket recognition: open edges are not recognized Fixed
31839 Chamfer recognition: Gouge with target Fixed
31915 Chamfer recognition: Toolpath is not generated Fixed
31900 Chamfer recognition: "Safety offset" doesn't effect on toolpath Fixed
31775 Chamfer recognition: Toolpath is not complete due to lead in/out Fixed
31780 Chamfer recognition: After change "Cutting diameter" Safety offset value changes too Fixed
31830 Drill recognition: Press on "Depth edit" button -> SolidCAM crashes Fixed
Machining Process 31714 MachProc Tool selection default should be in System units Fixed
30288 Add Hole Wizard Parameters to Machine Process + generate suitable geometries Implemented
31880 SolidCAM crashed if set tools to Permanent in MachProc Fixed
31744 When add machine -> SolidCAM doesn't give possibility to add similar machines Fixed
31480 Angle parameters from Hole Wizard in degrees, and not in radians. Implemented
31620 Add "Save & Copy " button Implemented
31742 Impossible to use tapered End Mill Tool in MachProc Fixed
31716 Add "Save & Exit" button Implemented
31718 Copy with new name doesn't work Fixed
31397 Switch from Pitch(mm) radio button to Pitch(Inch) -> field value is wrong Fixed
31456 Hole Wizard geometry recognition: Dump file of Hole Wizard Data Implemented
Machine Control Operation 31911 Wrong Tool Preview in MCO - holder is flipped Fixed
31613 Value of MCO Misc. parameter is not translated to the trace Fixed
31728 SolidCAM crashes when use "tool change" and generate the G-code Fixed
31487 Part is moving with move instead of part move Fixed
Probe 30683 Gauge with material during Probe Process in XY plane Fixed
Release notes
Page 5 2/5/2015
Simulation 31626 SC is crashed by running SolidVerify on manual turning operation Fixed
31311 HostCAD: Holder is hidden partially, when use option "hide holder" Fixed
31532 Incorrect STL holder orientation in solidVerify Fixed
31850 Toolpath changes after click on the screen (all types of simulations) Fixed
27722, 31478, 31652, 31725, 31772, 31419, 31835, 31810, 27539, 31086, 31270, 30840, 28361, 31379
SolidVerify simulation crash Fixed
28428 SolidVerify for 3D showing SLOW performance Fixed
31340 HostCAD: Wrong start of toolpath and movements between operation in MAC-to-MAC transformation
Fixed
30711 SolidVerify: Fixture is missing in simulation Fixed
Machine Simulation 30737 Wrong Second angle in MachSim. Fixed
31365 Turning tool is shown in wrong place in MachSim Fixed
31658 "Current toolpath is not for 4-axis machine. Posting process exception." on INDEX machine Fixed
31708 Turning toolpath is in wrong position Fixed
Templates 31790 Add default template for Chamfer recognition to the list in Settings Implemented
31627 Machining type and technology are set to "undefined" in template manager Fixed
Transformation 31117 "Optimize Jobs Loop" support in MAC-to-MAC transformation Fixed
Tooltable 31565 Wrong data in UI after Import of Tap/Pitch gets wrong data Fixed
30765 Tool is imported with missing details from ITA catalog Fixed