Software Update 2012-2 - John Deere · PDF fileSoftware Update 2012-2 ... • StellarSupport™ posts the latest versions of operator manuals available and includes ... • Latest

SSooffttwwaarree UUppddaattee 22001122--22 Release Notes

Important Notes:

• To ensure proper functionality, the most current version of display software, Apex™ desktop software, or preferred partner desktop software should be used. Please reference software versions at the end of this document.

o Model Year 2010 or previous planters will need SeedStar™ 2 software version 10 or higher to be compatible with this software update. Please contact a John Deere Dealer to get the latest version of planter software before updating the display and using a planter.

o John Deere Remote Display Access and JDLink Controller (MTG) Software Compatibility – In order to use John Deere Remote Display Access, it is currently required to have GreenStar™ 3 2630 Display software version 3.10.1390 (Software Update 12-1) and MTG software version 7.1.370.

If the GreenStar™ 3 2630 Display is updated to 3.13.1320 (Software Update 12-2), the MTG must also be updated with software version 8.1 to be compatible with John Deere Remote Display Access. Contact a local John Deere Dealer or GreenStar™ Support to get 8.1 MTG software when updating a GreenStar™ 3 2630 Display with the latest software.

• StellarSupport™ posts the latest versions of operator manuals available and includes additional information concerning changes in the new software update. Please see the following site to review and download the latest manual:

• North America: www.StellarSupport.com/en_US_new/categories/publications/ • Other Areas: www.StellarSupport.com and choose your respective country. Find your

manual under Technical Publications.

• As a reminder, since all data is stored directly in the GreenStar™ 2 1800 and GreenStar™ 3 2630 Displays, before performing any update it is recommended to back up data to protect the information in the event of an error during the update process.

• Activations are non-transferrable in the event of lost, stolen, or destroyed equipment. It is recommended to insure a display at full value, including activations.

Customer Contact Center Information Web: www.StellarSupport.com E-mail: [email protected] North America: SUPPORT 1-888-GRN-STAR (1-888-476-7827)

ACTIVATIONS: 1-888-953-3373 Australia: 0011-800-833-3373 New Zealand: 00-800-0000-3333 Brazil: 0-800-891-4031 Mexico: 866-582-4068 Argentina: 0800-444-9126 South Africa: 0800-983-821 Zimbabwe: (Access code: 110-98990) 888-983-3373 Zambia: (Access code: 00-899) 888-923-3373 **Countries w/ Access codes – Dial access code first and once prompted, enter the toll free number. Copyright © 1996-2012 Deere & Company

Release Notice These are the software update release notes for the GreenStar™ Displays and some related products. Apex™ Farm Management software release notes can be found on www.StellarSupport.com.

http://www.stellarsupport.com/en_US_new/categories/publications/�

http://www.stellarsupport.com/�




Displays: GreenStar™ 3 2630

John Deere Constituent Sensing – With Software Update 12-2, HarvestLab™ provides the capability to measure moisture and constituents in corn such as starch, protein and ADF/NDF. These constituents will be measured in real time on the John Deere Forage Harvester as well as on the stationary unit with the turn table. The totals will show on the GreenStar™ 3 2630 Display and can be transferred to desktop software. Constituent maps will only be available on the desktop software. (North America and Australia)

New Features

Necessary components:

• GreenStar™ 3 2630 Display with Software Update 12-2 • Latest software update on HMS Controller (Version 3.40A) • HarvestLab™ sensor with the latest software (Version 42) update and the calibrations loaded

and activated on the HarvestLab™ sensor.

ISO Task Controller Enhancement – The GreenStar™ 3 2630 Display now fully supports the use of two ISO Task Controllers on the same implement CAN Bus. This provides the ability to control the application of granular insecticide or fertilizer products with the GreenStar™ Rate Controller Dry on a SeedStar™ 2/SeedStar™ XP planter. The GreenStar™ 3 2630 Display will document up to four operations, four prescriptions (Rx’s), and John Deere Section Control on both ISO task controllers. This functionality is only available on the GreenStar™ 3 2630 Display with a GreenStar™ Rate Controller Dry and SeedStar™ 2/SeedStar™ XP planter. No additional ISO Task Controller combinations are approved at this time. (South Africa, South America, Mexico, North America and Australia) John Deere Implement Detection – With Software Update 12-2, data such as offsets and widths that are written in Apex desktop software will be transferred to the implement controller (SeedStar™ XP, John Deere Implement Detection Controller), leading to more consistent datasets. (All Regions)

John Deere Remote Display Access and JDLink Controller (MTG) Software Compatibility – In order to use John Deere Remote Display Access, it is currently required to have GreenStar™ 3 2630 Display software version 3.10.1390 (Software Update 12-1) and MTG software version 7.1.370.

• If the GreenStar™ 3 2630 Display is updated to 3.13.1320 (Software Update 12-2), the MTG must also be updated with software version 8.1 to be compatible with John Deere Remote Display Access. Contact a local John Deere Dealer or GreenStar™ Support to get 8.1 MTG software when updating a GreenStar™ 3 2630 Display with the latest software.

John Deere Remote Display Access Enhancements – With Software Update 12-2, tones were implemented to notify when a remote display session request is received and also when the session has ended. (All Regions)

• The MTG subscription and software version information are now shown in JDLink terminal setup.

• A remote display session may now be conducted from MyJohnDeere.com in addition to JDLink.

o MenuMy EquipmentSelect MachineView Display



• A warning message will now pop up on the web screen if the display is not communicating (most commonly will occur when display is not powered on).


Rows and Width Settings – The GreenStar™ 3 2630 Display will now properly keep the number of rows and width settings for the implement on reboot. (All Regions)

Resolved/Informational Items

StarFire™ 3000 Receiver

SF2 Option When Mobile RTK is Unavailable in Europe – If Mobile RTK loses corrections and times out of RTK-Extend, there is an option to revert to SF2 correction mode. This option may be enabled by a checkbox on the setup page of the receiver. (Europe)


• There is no SF2 subscription fee for this service. If the checkbox is marked, the system

will transition from RTK to RTK-Extend to SF2 and back to RTK, without disengaging AutoTrac™. The receiver may operate in SF2 for up to 14 days before requiring a connection to RTK again. Please see the operator manual for more information. Note: If sub-inch RTK accuracy is required at all times, this feature should not be used.

RTK Base Station Quality Indicator Improvement – With Software Update 12-2, diagnostic addresses 140-142 indicate in centimeters the average drift of the base station position over the previous 24 hours. Values will indicate if the base station receiver is experiencing shading or multi-pathing. (All Regions)

Guidance: AutoTrac™, AutoTrac™ Universal, AutoTrac™ RowSense™


John Deere Machine Sync – John Deere Machine Sync has become a new option on GreenStar™ 3 2630 Displays with Software Update 12-2. This new product enables automated in-field logistics and unloading between a combine and grain cart. Special software addition required, please see your dealer for more information. (Select Regions Only)

New Features

• John Deere Machine Communication Radio – This new product provides wireless

networking capability for machines using John Deere Machine Sync.

Adaptive Curves Swap Track Enhancement – Adaptive Curves have been added to Swap Track as a guidance line option on the GreenStar™ 3 2630 Display. This will enable toggling between existing Straight Track, AB Curve, Circle Track, or Adaptive Curve guidance lines. (All Regions) Multiple Adaptive Curves per Field – It is now possible to record and recall more than one Adaptive Curve per field on the GreenStar™ 3 2630 Display with a StarFire™ iTC or StarFire™ 3000 Receiver. (All Regions)

IMPORTANT: Custom Adaptive Curve track names are only compatible with GreenStar™ 3 2630 Display Software Update 12-2. All Adaptive Curve names created with this version of GreenStar™ 3 2630 Display software will be automatically renamed to ‘Curve Track’ when imported to a GreenStar™ 3 2630 Display with older software versions due to software compatibility issues.


Tramlines Enhancement – Adaptive Curves and Circle Track have been added to Tramlines as a guidance line option on the GreenStar™ 3 2630 Display. (All Regions)


Guidance Lightbar Change – With Software Update 12-2 on the GreenStar™ 3 2630 Display, when the “Show Shift Track Totals on Map” check box is selected on the Shift Track Settings tab, the guidance lightbar is no longer selectable and does not highlight or make an audible sound when selection is attempted. (All Regions)


Enhanced AutoTrac™ Diagnostics Now Shows Speed in KPH or MPH – The Enhanced AutoTrac™ Diagnostics page will now display speed values as KPH or MPH, based on the units of measurement selected for the GreenStar™ 3 2630 Display and GreenStar™ 3 CommandCenter™. (All Regions)

WAS Direction on New Holland T8050 – The John Deere AutoTrac™ Controller kit will now have the option to select “MX335, NH T8050” from the Machine Type drop-down when paired with a GreenStar™ 2 1800 Display or a GreenStar™ 3 2630 Display on a New Holland T-Series 8050 machine. By selecting this option, the Wheel Angle Sensor will read the direction of travel correctly, eliminating the instances of the system steering backward due to machine type. (All Regions)

Adaptive Curves Creates a 90-degree Turn – Using Adaptive Curves with a GreenStar™ 3 2630 Display will no longer cause a 90-degree line in a turn loop. (All Regions)

• The Adaptive Curve feature has been changed to allow the following capabilities: o When approaching a corner that was recorded in a loop pattern, the white tracking

line will end at the intersection of the loop.

o When the machine reaches this intersection, AutoTrac™ will disengage.


o After passing the intersection, the remaining portion of the recorded loop will be

shown. o Pressing the resume switch will return AutoTrac™ to this path.

Direction of Travel in an Articulated Machine – With Software Update 12-2, the direction toggle button will be available on the GreenStar™ 3 2630 Display when operating an AutoTrac™ Universal and StarFire™ iTC Receiver in an Articulated machine. Access to the direction toggle button will allow for a manual change to the direction of travel when the direction is initialized incorrectly. (All Regions) AutoTrac™ Universal 200 Performance After Endrow Turns – With Software Update 12-2, encoder software corrections were made to improve field performance of the AutoTrac™ Universal 200. (All Regions)

Incorrect Tracking Mode Displayed – The GreenStar™ 3 2630 Display now shows all tracking modes, including Row Finder, Ditch Track, and Levee Track on the GreenStar™ Summary Page. (All Regions)

Field and Crop Management: John Deere Section Control, John Deere Harvest Identification, John Deere Mobile Weather, GreenStar™ Rate Controller

GreenStar™ Rate Controller Dry Max Product Limit – The maximum number of products that can be created on the controller has increased to 20. In the past, a limit of 10 products could be created on the controller. (South Africa, South America, Mexico, North America and Australia)

New Features

GreenStar™ Rate Controller Dry Air Seeding – GreenStar™ Rate Controller Dry can now be configured as an Air Cart implement type, providing the ability to control the product application on single tank Air Cart configurations. (South Africa, South America, Mexico, North America and Australia)


GreenStar™ Rate Controller Dry Bin Fill Limit – With Software Update 12-2, bin fill level may now be entered up to 30% greater than the calculated bin heaped capacity. When the bin capacity is entered, it will appear as the value on the bin icon. The visual bar graph indicator for bin level will also appear as "full" on the main GreenStar™ Rate Controller Dry run page. The number will count down as the bin empties and the bar graph indicator will stay at the full level until the calculated bin heaped capacity is reached. (South Africa, South America, Mexico, North America and Australia)

GreenStar™ Rate Controller Dry Manual Target Rate – GreenStar™ Rate Controller Dry has been updated to allow the entry of a single decimal place for the target rate for both main bins and micronutrient bins when in manual rate mode. (South Africa, South America, Mexico, North America and Australia) GreenStar™ Rate Controller Dry Implement Offsets – Changes have been made for the GreenStar™ 3 2630 Display to save Implement Offsets to the Implement Name in the GreenStar™ Rate Controller Dry Implement Setup. Once data is entered for a valid configuration (requiring implement and product setup in the GreenStar™ Rate Controller Dry), the operator will need to setup the Implement Model, Implement Name and Offsets on the GreenStar™ Equipment -> Implement 1 tab. (South Africa, South America, Mexico, North America and Australia)

• The Implement Name in GreenStar™ should reflect the Implement Name in the GreenStar™ Rate Controller Dry.

• The offsets entered for a given Implement Name will be saved to that name and will not revert to default measurements unless the Implement Name is changed on the GreenStar™ Rate Controller Dry.

• Offsets in GreenStar™ will need to be adjusted each time a new Implement Name is created on the GreenStar™ Rate Controller Dry.


GreenStar™ Rate Controller Manual Target Rate – The flow target rate (gallons per minute/liters per minute) will now remember the previously set target flow when switching between the GreenStar™ Rate Controller rate modes. (North America, Australia, Sub-Saharan Africa)


GreenStar™ Rate Controller Homepage – A new homepage configuration option as been added for the GreenStar™ Rate Controller. This configuration allows the ability to configure a region of a given homepage to show five values (all totals, rates and master switch status) based upon preference. (North America, Australia, Sub-Saharan Africa)

Please visit the John Deere Custom Performance website to view and/or update all other controllers.

http://customperformance.deere.com/�


Software Versions – Bold items have changed.

Version # Description 3.13.1320 GreenStar™ 3 2630 Display 2.8.1031 GreenStar™ 2 2600 Display

2.11.1068 GreenStar™ 2 1800 Display GSD 1.97 B Original GreenStar™ Display

ITC 1.60 M StarFire™ 3000 Receiver ITC 3.73 E StarFire™ iTC Receiver LCR 1.10 C StarFire™ 300 Receiver SF 7.70 B StarFire™ Gen II Receiver

1.69 E StarFire™ RTK 435-470 MHz 2.32 B or 2.65 C StarFire™ 900 RTK Radio

1.72 John Deere RTK Radio 450 1.73 John Deere RTK Radio 450 (PFA10094, PFA10095, PFA10096) 3.34 John Deere RTK Radio 869 3.35 John Deere RTK Radio 869 Multiple Repeater

1.10A Machine Communication Radio TCM 1.09 A TCM

2.10 F Application Controller 1100 (iGrade, Active Implement Guidance)

1.00 A Application Controller 1120 (John Deere Mobile Weather, John Deere Harvest Identification, Cotton)

8.1 MTG (JDLink Controller) ATU 1.13 A AutoTrac™ Universal (ATU) ATU 2.14 A AutoTrac™ Universal (ATU) 200 GRC 3.40 R GreenStar™ Rate Controller GDC 2.00 V GreenStar™ Rate Controller Dry RG2 2.01 E AutoTrac™ RowSense- Universal Sensor CAT 1.11 B AutoTrac™ Controller

HMCT 1.07 C Harvest Monitor™ Cotton SCM CMFS 2.07C Cotton Mass Flow Sensor CMFS SMON 1.73 A Original Harvest Monitor™ SPFH HMON 1.20 C Harvest Monitor™ Combine with In-Tank Moisture MST 7.01 B Harvest Monitor™ Elevator Mount Moisture Board

AC2 11 Original Air Cart SMVR 1.01M SeedStar™ Gen II

CDOC 3.56 A Field Doc™ Connect FDOC 3.57 A Field Doc™ Basic TRAC 5.06B Keycard ADOC 1.25 A Field Doc™ AirCart PDOC 3.55 A Field Doc™ Planter PDOC 6.78 A Field Doc™ Planter SDOC 3.44 A Field Doc™ Sprayer HDCT 1.13 A Harvest Doc™ Cotton HDSP 4.13 A Original Harvest Doc™ SPFH HDOC 1.54 A Harvest Doc™ Combine YMAP 6.61 A Combine Yield Mapping MST 6.60 B Combine Yield Monitor (Gen I Moisture Sensor – ISO 2.5v Dual CAN) MST 5.60 A Combine Yield Monitor (Gen I Moisture Sensor – Deere 4/5 CAN)


1.12A Lightbar

YWW0D6_6.Y12 Reprogramming back to Combine Yield Mapping 3.40A GreenStar™ 2 Harvest Doc™ SPFH (controller)

42 HarvestLab™ Sensor

13 SeedStar™ 3.4 Apex™

Open Source Copyright Information

Portions of the licensed software use the WCECompat software library, which is licensed under the GNU Lesser General Public License, version 2.1. For a copy of this license, please see:

WCECompat

http://github.com/mauricek/wcecompat/blob/51a25c52d94e6b24fc073d179e7497d8a2c06d61/LICENSE. The WCECompat library was originally obtained from: http://github.com/mauricek/wcecompat/. The source code and build system for the WCECompat library supplied can be obtained by contacting support at: John Deere Intelligent Solutions Group, ATTN: John Deere Display, 4052 114th Street, Urbandale, IA 50322 U.S.A.

Copyright (c) 1998-2011 The OpenSSL Project. All rights reserved. OpenSSL

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the

following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and

the following disclaimer in the documentation and/or other materials provided with the distribution. 3. All advertising materials mentioning features or use of this software must display the following

acknowledgment: "This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)"

4. The names "OpenSSL Toolkit" and "OpenSSL Project" must not be used to endorse or promote

products derived from this software without prior written permission. For written permission, please contact [email protected].

5. Products derived from this software may not be called "OpenSSL" nor may "OpenSSL" appear in

their names without prior written permission of the OpenSSL Project. 6. Redistributions of any form whatsoever must retain the following acknowledgment: "This product

includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/)"

THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT ``AS IS'' AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES

http://github.com/mauricek/wcecompat/blob/51a25c52d94e6b24fc073d179e7497d8a2c06d61/LICENSE�

http://github.com/mauricek/wcecompat/blob/51a25c52d94e6b24fc073d179e7497d8a2c06d61/LICENSE�

http://github.com/mauricek/wcecompat/�

http://www.openssl.org/�

mailto:[email protected]�

http://www.openssl.org/�


(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ==================================================================== This product includes cryptographic software written by Eric Young ([email protected]). This product includes software written by Tim Hudson ([email protected]).



Documents

Software Update 2012-2 - John Deere · PDF fileSoftware Update 2012-2 ... • StellarSupport™ posts the latest versions of operator manuals available and includes ... • Latest