1

EGA Master Sledge Hammers have been designed for striking operations in potentially explosive environments such as the shipbuilding industry, the maintenance of industrial and petrochemical plants…

SLEDGE

HAMMER

2. Safety pin or conical go-through handle for per-fect fixation handle-head to avoid the head coming off. This means that risks from accidents are reduced.

3. Models with ultra-resistant fiberglass handle and outer zone in PP and TPR for maximum strength and adherence.

5. Available in Cu-be and Al-bron alloy, Brass and Copper.

Available in

Lb and Kg

4. Models with Hickory wooden handle providing an excellent resis-tance to bending and impact.

1. They are an ideal solution for striking operations in potentially explosive environments.

2

SLEDGE HAMMER

Cu-Be Al-BronHardnessCu-Be

HardnessAl-Bron

lb

35762 35763 380 3

283-365 Brinell

229-291 Brinell

35764 35765

840

535766 35767 7.1/235768 35769 1035770 35771 1535772 35773 18

35865 35882370

1

283-365 Brinell

229-291 Brinell

35866 35883 1,535867 35884 2,035868 35885

900

2,535869 35886 3,035870 35887 4,535871 35888 5,035872 35889 6,835873 35890 8,035874 35891 10 35875 35892 12

Cu-Be Al-BronHardnessCu-Be

HardnessAl-Bron

Cu-Be Al-BronHardnessCu-Be

HardnessAl-Bron

lb

35876 35893 380 3

283-365 Brinell

229-291 Brinell

35877 35894

840

535878 35895 7.1/235879 35896 1035880 35897 1535881 35898 18

70502 71757370

1

283-365 Brinell

229-291 Brinell

70503 71758 1,570504 71759 2,070505 71760

900

2,570506 71761 3,070507 71762 4,570508 71763 5,070509 71764 6,870510 71765 8,072213 72211 10 72975 72974 12

Cu-Be Al-BronHardnessCu-Be

HardnessAl-Bron

“This document has been created by and is the property of EGA Master S.A. Thus, all intellectual rights belong to EGA Master. Any total or partial copy of this document in any physical, electronic or any other form is strictly forbidden. EGA Master will

legally proceed against any infringement of these rights.” 3

Cu

SLEDGE HAMMER

35975 350 45035976 400 100035977

900

250035978 360035979 450035980 540035981 640035982 10000

Cu72750 350 45072751 400 100072752

900

250072753 360072754 450072755 540072756 640072757 10000

Copper or brass tools can never be considered as alternatives to aluminum-bronze or copper-beryllium alloy tools, because their hardness is too low for most applications. There is the temptation to choose copper or brass tools due to their lower cost compared to aluminum-bronze or copper-beryllium ones. This choice is not only risky in itself, but in the short/mid term it will be necessary to replace them for new ones because they wear out fast.

Copper

Copper

Brass35965 280 30035966 310 50035967

4001000

35968 150035969 200035970

900

300035971 400035972 500035973 700035974 10000

Brass72740 280 30072741 310 50072742

4001000

72743 150072744 200072745

900

300072746 400072747 500072748 700072749 10000

Brass

Brass