-
1
2
3
SQE-2SQE-RL
SQE-3ESQE-3DSQE-33
Sivoia QED™ Euro-styleKeypadsfor use with Lutron Sivoia
QEDTMMotorized Window Treatment System
-
Open button
Status IndicatorLEDs
Open button
2
SQE-2
Status IndicatorLEDs
SQE-RL
SQE-3D
Open buttonClose button
SQE-33
SQE-3E
InfraredReceiverRaise/Lower
Installation Instructions Occupant Copy
Please read before installing.
CAUTION!Lutron recommends that Keypads be installed by a
qualified electrician.
Do not connect high-voltage power to low-voltage terminals.
Improper wiring can result in personal injury or damage tothe
control or to other equipment.
Keypads must be connected to the Sivoia QEDTM Electronic Drive
Unit (EDU) by using Class 2 (USA)/ PELV(IEC) wiringmethods. Check
with your local electrical inspector for the local code
requirements and wiring practicesallowed in your area.
Use only a cloth with warm water and mild soap to clean
faceplates (no chemical cleaners).
Keypad Configurations
Status IndicatorLEDs
Raise buttonLower button
Preset buttonClose button
Raise/Lower
Status IndicatorLEDs
Preset buttonClose button
1
2
3
Open button
Status IndicatorLEDs
Group SelectionLEDs
Preset buttonClose button
Group 1 buttonGroup 2 buttonGroup 3 button
-
Button FunctionalityTap the Open, Close, or Preset button to
move the windowtreatments to the selected position. While pressing
the Raise orLower button, the window treatments will raise or
lower.
Numbers - Tapping one of the numbered buttonswill select a group
of EDUs to control.
Open - Tap the open button to move the windowtreatments to the
fully-open position.
Preset - Tap the preset button to move the windowtreatments to
their programmed preset level.
Close - Tap the close button to move the windowtreatments to the
fully-closed position.
Raise - Holding the raise button will move thewindow treatments
towards the open position.Releasing the raise button will cause the
windowtreatments to stop.
Lower - Holding the lower button will move thewindow treatments
towards the closed position.Releasing the lower button will cause
the windowtreatments to stop.
Note: Holding the or buttons for 5 secondswill cause the window
treatments to move all theway open or closed automatically.
3Occupant Copy Installation Instructions
Wiring NotesSystem Maximums:— Up to 96 devices total on one
system.
One transformer per EDU.— The Keypads wire to the Sivoia QED
Communication
Link. The Link can not exceed 1220 m (4000 ft) total.— The
Keypads are either powered by EDUs or Keypad
Power Supplies. Each EDU can provide power for oneKeypad. The
number of Keypads should not exceedthe number of EDUs unless
connecting with a KeypadPower Supply.
— The maximum distance between any two Sivoia QEDdevices is 305
m (1000 ft) unless specified otherwise.
— Operating environment should be between 0 °C -40 °C (32 °F -
104 °F).
Keypad Wiring— Two 1.0 mm2 (#18 AWG) wires for power and two
shielded 1.0 mm2 (#18 AWG) stranded wires for data(twisted
pair).
— Power: wires 1 & 2, 12 - 15 V .— Data: wires 3 & 4,
twisted, shielded pair.
Sivoia QED Link wiring layouts are shown on the nextpage.
1, 2, 3
-
4
Sivoia QED Link:Class 2/PELV Wiringconnections to EDUs,Power
Panels, orother Keypads.
Male EDU Connector
Sivoia QED Keypad Wiring
Installation Instructions Occupant Copy4
4. Each Keypad terminal will accept up to two 1.0 mm2
(#18 AWG) wires.
Connect two 1.0 mm2 (#18 AWG) wires to terminals 1 and2 of the
Keypad’s terminal block.
Connect two 1.0 mm2 (#18 AWG) shielded, twisted pairwires to
terminals 3 and 4 of the Keypad’s terminal block.
1234
Com
mon
12V
MUX
MUX
AC1
AC2
EGND
Female EDUConnector
Sivoia QED EDU
Back of Sivoia QED Keypad
InstallationKeypad circuits are classified as Class 2 circuits
(U.S.A.) andPELV circuits (IEC). When installing and wiring to
theseKeypads, follow all applicable national and/or local
wiringregulations.
Warning: Always turn Off the circuit breaker orremove the main
fuse from the power line beforedoing any work. Failure to do so can
result inserious personal injury.
1. Turn power Off to all EDUs and power panels.
2. Mount standard German or UK backboxes (60 mmmeasured centre
to centre of mounting holes).
3. Strip insulation from wires so that 10 mm. (3/8 in) of
barewire is exposed for 1.0 mm2 (#18 AWG) wire.
ON
OF
F
ON
OF
F
ON
OF
F
10 mm (3/8 in.)
-
5Occupant Copy Installation Instructions
5. Remove the faceplate from the Keypad. To remove thefaceplate,
pull outward at each corner, one corner at atime.
6. Mount Keypad as shown in the diagram below.
7. Attach faceplate by pressing in at each corner, one cornerat
a time.
Thread all four screws before tightening.
Wallbox
Wall
Mounting Frame Orientation
Wallbox MountingFrame
Carrier Faceplate
MountingFrame
Addressing the SystemNote: For the SQE-RL, use the and buttons
instead ofthe and buttons.
1. Enter programming mode on the Keypad by pressing andholding
the Open ( ) and Close ( ) buttonssimultaneously for 5 seconds. The
LEDs next to the Open( ) and Close ( ) buttons will flash once per
second,indicating the Keypad is in Programming mode.
2. Initiate system addressing by tapping the Open ( ) button.The
LED next to the Open ( ) button will flash quickly (8times a
second) and the LED next to the Close ( ) buttonwill turn off. The
system is now being automaticallyaddressed.
Press the Open ( ) andClose ( ) buttonssimultaneously for
5seconds.
Flashingonce persecond
3. Wait for system addressing to be completed. This will
takeapproximately one minute. While addressing is in progress,each
Keypad will flash the Open ( ) LED quickly (8 timesa second). When
addressing has successfully completed,the Open ( ) and Close ( )
LEDs on each Keypad in thesystem will flash slowly (once per
second).
4. When system addressing is complete, exit Programmingmode by
pressing and holding the Open ( ) and Close( ) buttons
simultaneously for 5 seconds. The Open ( )and Close ( ) LEDs will
stop flashing.
Tap the Open ( )button.
Flashing 8times persecond
-
4. Adjust the currently selected EDU to the desired level,using
the Raise ( ) and Lower ( ) buttons on theKeypad.
6
Setting LimitsNote: Entering Limit Setup mode may cause
thewindow treatments to move approximately 200 mm(8 in) up or down.
Be sure that each window
treatment is positioned such that the fabric can safelymove
approximately 200 mm (8 in) before enteringLimit Setup mode.
Note: When using Keypads that do not have Raise and
Lowerbuttons, set the limits at the EDU. Refer to the Sivoia
QEDWiring and Programming Guide for more information.
1. If using the SQE-33, select the group you wish to assign.
2. Enter Limit Setup mode by pressing and holding the Open( )
and Raise ( ) buttons simultaneously for 5 seconds.The LED next to
the Open ( ) button will flash once persecond and the LED next to
the Close ( ) button will flashquickly (8 times per second).
3. Select the EDU to adjust using the Open ( ) button on
theKeypad. Each time the Open ( ) button is tapped, an EDUwill
begin opening and closing over a range ofapproximately 200 mm (8
in). Repeat tapping the Open ( )button until the desired EDU is
selected. The Close ( )button can also be used to select EDUs by
moving throughthe EDUs in the opposite order.
5. Store the current position as the Open ( ) limit bypressing
and holding the Open ( ) button on the Keypadfor 5 seconds. The LED
next to the Open ( ) button willturn on for two seconds.ORStore the
current position as the Close ( ) limit bypressing and holding the
Close ( ) button on the Keypadfor 5 seconds. The LED next to the
Close ( ) button willturn on for two seconds.
6. Use the Open ( ) or Close ( ) buttons to select otherwindow
treatments and adjust the limits as in Steps 3 and4.
7. Exit Limit Set mode by pressing and holding the Open ( )and
Raise ( ) buttons simultaneously for 5 seconds.
Installation Instructions Occupant Copy
LED on for 2seconds
Press & holdhere to set theOpen ( ) limit
Press the Open ( )and Raise ( ) buttonssimultaneously for
5seconds.
LED flashing onceper second
LED flashing 8 timesper second
Press the Raise ( ) orLower ( ) button.
LED on for 2seconds
Press & holdhere to set theClose ( ) limit
-
77Occupant Copy Installation Instructions
EDU AssignmentNote: Entering Assignment mode will cause
thewindow treatments to move between their Open andClose limits. Be
sure that the Open and Close
limits have been set appropriately.
Note: For the SQE-RL, use the and buttons instead ofthe and
buttons.
1. If using the SQE-33, select the group you wish to assign.
2. Enter Programming mode on the Keypad by pressing andholding
the Open ( ) and Close ( ) buttonssimultaneously for 5 seconds. The
LEDs next to the Open( ) and Close ( ) buttons will flash once per
second,indicating the Keypad is in Programming mode.
3. Initiate Assignment mode by tapping the Close ( ) button.The
LED next to the Close ( ) button will continue to flash(once per
second) and the LED next to the Open ( )button will turn off. EDUs
that are assigned to the Keypad inAssignment Mode will move to
their Close limit. EDUs thatare not assigned to the Keypad will
move to their Openlimit.
4. Tap any button on an EDU to toggle between assignmentor
unassignment with the Keypad.ORUse the Open ( ) button to step
through each EDU in thesystem. Each time the Open ( ) button is
tapped, awindow treatment will begin opening and closing
overapproximately 200 mm (8 in). Repeat tapping the Open( ) button
until the desired EDU is selected. The Close( ) button can also be
used to select EDUs in theopposite order.
5. Assign or unassign the currently selected EDU using theRaise
( ) and Lower ( ) buttons. To assign, tap theLower ( ) button. To
unassign, tap the Raise ( )button.
6. Check assignment before exiting Assignment mode. EDUsthat are
at the Close limit are assigned. EDUs that are atthe Open limit are
unassigned.
7. Exit Assignment mode by pressing and holding the Open( ) and
Close ( ) button simultaneously for 5 seconds.Each EDU will return
to the level it was at whenAssignment mode was entered. The Open (
) and Close( ) LEDs will stop flashing.
Press the Open ( )and Close ( )buttonssimultaneously for
5seconds.
Flashingonce persecond
Tap the Close ( )button.
Flashingonce persecond
Tap the Raise ( )or Lower ( )button.
-
8
Lutron Electronics Co., Inc.7200 Suter RoadCoopersburg, PA 18036
U.S.A.Made and printed in U.S.A.P/N 040-227-12 Rev. A 1/05
Limited WarrantyLutron EA Ltd. (“Lutron EA”) warrants each unit
to be free from defects in material andworkmanship and to perform
under normal use and service. To the extent permitted by law,Lutron
EA and Lutron Electronics Co. Inc. (“Lutron”) make no warranties or
representations asto the units except as set forth herein. This
warranty shall run for a period of one year from thedate of
purchase and Lutron’s obligations under this warranty are limited
to remedying anydefect, replacing any defective part or replacement
(at Lutron EA’s sole option) and shall beeffective only if the
defective unit is shipped to Lutron EA postage prepaid within 12
monthsafter purchase of the unit, to the extent permitted by law.
Repair or replacement of the unitdoes not affect the expiry date of
the warranty. This warranty does not cover damage ordeficiencies
due to abuse, misuse, inadequate wiring or insulation or use or
installation otherthan in accordance with instructions accompanying
the unit.Although every attempt is made to ensure that catalogue
information is accurate and up-to-date, please check with Lutron EA
before specifying or purchasing this equipment to
confirmavailability, exact specifications, and suitability for your
application.This warranty does not affect the statutory rights of
consumer purchasers of the unit.These products may be covered by
one or more of the following US patents: 4,835,343;4,924,349;
D422,567; D436,930; D453,742; D456,783; D461,782; D465,460;
D465,770;D466,090; D466,091; D466,484; D475,024; D475,025; and
corresponding foreign patents.US and foreign patents pending.
Lutron, the Sunburst logo, and Sivoia are registeredtrademarks, and
Sivoia QED is a trademark of Lutron Electronics Co., Inc.© 2005
Lutron Electronics Co., Inc.
Note: The current position is stored as a preset only on theEDUs
that are assigned to that preset button. The preset is
onlyaccessable from that particular Keypad.
TroubleshootingFor information on troubleshooting, please refer
to the SivoiaQED Wiring and Programming Guide.
Storing PresetsSivoia QED EDUs have the ability to store
positions as presets.
1. Set all EDUs controlled by the Keypad to the desired
levelusing the Raise ( ) and Lower ( ) buttons on theKeypad.
2. Store the EDUs’ current position as a preset by pressingand
holding the desired Preset ( ) button for 5 seconds.The LED next to
the Preset button ( ) on the Keypad willflash and then turn on,
indicating that the preset has beenstored.
Technical AssistanceEUROPEAN HEADQUARTERSLutron EA Ltd.6
Sovereign CloseLondon, E1W 3JFUnited KingdomTel:
+44-(0)20-7702-0657Fax: +44-(0)20-7480-6899
CUSTOMER SERVICE/ORDERINGUK +44-(0)20-7702-0657 – 09.00 - 18.00
GMTUSA +1-610-282-3800 – 08.00 - 20.00 EST
CUSTOMER SERVICE/[email protected]
TECHNICAL SUPPORT & SERVICESUK +44-(0)20-7702-065709.00
-18.00 GMTUSA +1-610-282-3800 – 24 hours/7daysINTERNET:
www.lutron.com
WORLD HEADQUARTERSLutron Electronics Co., Inc.7200 Suter
RoadCoopersburg, PA 18036United StatesTel:
+1-610-282-3800Fax:+1-610-282-1243
Press the Preset ( )button for 5seconds.
LED willflash andthen turnon.
