Upload
branden-freeman
View
221
Download
0
Embed Size (px)
Citation preview
Siplace Vision Training
What‘s new?
New cameras: – RV12-head: Type 28 (old: 12)– RV6-head: Type 29 (old: 13)– Twin-head: Type 33 (old 22)
– PCB-camera: Type 34
What‘s new?
Component-type:– Baredie– Chip– Melf– Moulded– ECV– SOT– DPack– SOxx
– QFP– SOJ– PLCC– BGA– CCGA
– Sockets– Connector– Shield– Nonstandard
What‘s new
New lead-types– Corner to describe shields
– Blob to describe leads of any shape: for example oval: or undefined shape:
What‘s new?
No ICOS-computer any more - Siplace Vision is an application running on station computer
old: new:
SCICOSvisioncomp
SCvision comp
SV-appl
What‘s new?
Component face-down recognit.
Pattern-fiducial:– it is now possible to teach any pattern on PCB as
a fiducial. For instance: corners of circuit pathes
Area used as ficucial
What‘s new?
Autosave of failed component measurements– By analysing the stored dumps you can see why
the components were rejected.
This is a really big help to find and avoid errors and lower reject rates.
How to program- Preparations in SiPro
Already existing GF:1. If not yet done set the correct type in SiPro.2. If not yet done add digital cameras.3. For standard components SV will use ICOS-GF-data => Do not mark checkbox
„Requires seperate group description“!!!4. Only mark checkbox for components that have leadtypes ICOS does not
know!For example: Shields (corners) or components you described with „blob“ leads.(Teach these components on the station before production!)
5. If possible / required check „Detect flipped Component“.6. If you get error messages during optimizing correct existing GFs according to
optimizer‘s messages. For example: Lead tolerance <50% of lead size
1
3
5
How to program- Preparations in SiPro
New standard GF:1. Enter the correct dimensions (X,Y,Z) to pick up
the component correctly.2. Set type to „Baredie“ – you dont have to
describe leads then.3. Teach the component on the station (and set the
correct type).
Do not check!
1
1
2
It is not necessary to create leads here!Leads will be created through Sipl. Visionby teaching the component on the station.
The Siplace Vision groups are disabledbecause Sipl. Vision will use ICOS groupsfor components with standard lead shapes(Gullwing, J-Bend, Wraparound, Ball)
How to program- Preparations in SiPro
New special GF (shield, sockets, „blobs“, …):– Describe the GF correctly for the ICOS system.– Set the type baredie.– Mark checkbox „Requires seperate group description“– Test the component on an ICOS machine.– Teach the component on an SV machine and set the
correct type.– By teaching on the machine the lead groups for SV will be
written to SiPro database.
With seperate group descriptions SVhas no effect on ICOS lead groups.So you have to describe them manually.
It is not necessary to create leads here!Leads will be created through Sipl. Visionby teaching the component on the station.
How to program on the station
General things– First make sure the dimensions and geometry are
correct– If the GF does not run with an exact geometrical
description adust illumination– Adjusting algorithms is the very last step and only
needed in rare exceptions!
How to program on the station
In case of an error scroll through the list of measuresteps and find the failing step.
Look at the filters. Is it the correct one? Are the dimensions of the filter correct?
How to program on the station
SO4 SO4 SO4
How to program on the station
SO4 SO4 SO4