Embed Size (px)
Citation preview
Signum® Bonding AgentsRepair solutions for every situation.
Giving a hand to oral health.
45581_NCC_Signum_Bonding_Agents_Flyer_GB.indd 145581_NCC_Signum_Bonding_Agents_Flyer_GB.indd 1 25.07.13 15:0725.07.13 15:07
0
5
10
15
20
25
30
[MPa]
2 3
Signum – For the love of perfection.
Regardless of how you like to work, the Signum range with its modular design will have a product to suit you.
Signum cre-active
Stains for characterisation, e.g. for fissure contrast, white striation, and a whole lot more.
Signum matrix
Flowable consistency for thin sections in the margin or incisal area with light optic properties.
Signum accessories
Bonding agent for all materials, polishing and finishing tools, polishing pastes, insulation, light curing units etc.
Signum® – is, when one thing perfectly fi ts another.
Signum® – metal bond.
Pack contents:1 x Signum metal bond I1 x Signum metal bond II1 x Mixing wellArt.-No.: 66033913
Indications:
■ Bonding agent for the repair of metal based ceramic restorations together with Signum ceramic bond and direct composite (e.g. Venus Diamond).
■ Bonding of metal framework surfaces to composite. ■ Bonding of root canal posts, Maryland bridges to composite cement. ■ Bonding agent for the re-creation of composite restorations.
Features:
■ Intraoral and extraoral application. ■ Innovative cold bonding system based on new technology providing up to 300 percent better adhesion.
■ Extremely thin layer of bonding agent results in a smaller total thickness of layering (up to 20 %), therefore allowing more options for composite layering.
■ Easy and efficient application.
Comparison of shear bond strength of several bonding systems*
retention flow opaque Alloy Primer/Kuraray
Signum metal bond II Signum metal bond I
retention flow opaque Metal Primer II/GC
– Metal Primer II/GC
*shear bond strength test according to ISO 10477: 2004 University of Tübingen, Germany / Prof. Dr. rer. nat. Jürgen Geis-Gerstorfer
Heraenium CE Bio Maingold SG
Signum composite
Signum opaque F
Signum opaque F
Signum metal bond ll
Signum metal bond lMetal frame
Bifunctional bonding molecules are bound permanently according to a lock-and-key mechanism. This ICT layer is much thinner when compared to that of conventional bonding agents allowing the user more options Signum for application of additional composite layers.
(build up with two layers of opaque, one layer of Signum composite dentine)
Signum composite Signum composite flow
Metal-supported
Signum ceramis
Metal-free
Signum metal bond
Bonding agent for metal based ceramic restorations
Signum zirconia bond
Bonding agent for zirconia based resto-rations
Signum ceramic bond
Bonding agent for all silicate ceramics
45581_NCC_Signum_Bonding_Agents_Flyer_GB.indd 2-345581_NCC_Signum_Bonding_Agents_Flyer_GB.indd 2-3 25.07.13 15:0725.07.13 15:07
0
5
10
15
20
25
30
[MPa]
0
5
10
15
20
25
30
35
[MPa]
4 5
Signum® – zirconia bond.
Pack contents:1 x Signum zirconia bond I1 x Signum zirconia bond II1 x Mixing wellArt.-No.: 66038530
Indications:
■ Bonding agent for the repair of zirconia based ceramic restorations together with Signum ceramic bond and direct composite (e.g. Venus Diamond).
■ Bonding of zirconia framework surfaces to composite. ■ Bonding of root canal posts, Maryland bridges to composite cement. ■ Bonding agent for the re-creation of composite restorations.
Features:
■ Intraoral and extraoral application. ■ High bonding strength. ■ Extremely thin layer. ■ Easy and efficient application.
Test of shear bond strength* (according to ISO 10477)
Signum ceramis Metal/zirconia primer
Signum ceramis Signum zirconia bond
Signum composite Metal/zirconia primer
Signum composite Signum zirconia bond
* Source: Universitätsklinikum Jena [University Medical Centre], Fachbereich Prothetic und Werkstoffkunde [Prosthetics and Materials Science], Prof. Dr. med. dent. habil. H. Küpper, Dr. Roland Göbel, March 2008, documentation available.
with Signum opaque F without Signum opaque F 5000 TWL
Preparing the bonding surface before cementation.
Preparing the surface before veneering or repairing.
Signum® – ceramic bond.
Indications:
■ For all silicate ceramics. ■ Use for intraoral and extraoral repair at chairside with a direct composite. ■ For preparation of the bonding surface before cementation. e.g. ceramic restorations using resin cements.
■ To generate a dispersion layer in order to achieve connection / bond with (meth-)acrylate based composite (e.g. Venus Diamond).
■ For elongation of pontics.
Features:
■ Quick, safe and secure handling. ■ Intraoral and extraoral application. ■ No need for polymerisation. ■ Extraordinary bonding strength and durability (up to 30 MPa according to ISO 10477).
Pack contents:1 x Signum ceramic bond I1 x Signum ceramic bond II1 x Mixing well25 x Disposable brush tips5 x K1 Bur1 x Instruction sheetArt.-No.: 66039817
Comparison of shear bond strength on silicate-ceramic* (according to ISO 10477)
*Measurements done by R&D HKG-Wehrheim.
VOCO – Cimara
Ivoclar – Monobond S + Heliobond
Heraeus Kulzer – Signum ceramic bond I + II
Arabesk DA3
CIMARA-Opakerliquid
Cimara
HeraCeram
Tetric Evoceram
Heliobond
Monobond S
HeraCeram
Venus Diamond
Signum ceramic bond II
Signum ceramic bond I
HeraCeram
45581_NCC_Signum_Bonding_Agents_Flyer_GB.indd 4-545581_NCC_Signum_Bonding_Agents_Flyer_GB.indd 4-5 25.07.13 15:0725.07.13 15:07
6 7
Signum® – Ceramic repair process with exposed metal*. Signum® – Ceramic repair process.
1. Roughen the metal and ceramic ■ Use the K1 bur for the ceramic and for the metal surface. ■ Clean the surface by brush or air stream.
2. Signum metal bond I* ■ Apply the Signum metal bond I onto the metal and wait 15 seconds for it to evaporate.
3. Signum metal bond II* ■ Apply the Signum metal bond II onto the metal and then light cure for 40 seconds e.g. Translux Power Blue.
5. Signum ceramic bond I ■ Apply Signum ceramic bond I onto the ceramic and wait 10 seconds for it to evaporate.
7. Replace the broken veneer ■ Repair the defect area with direct composite (Venus Diamond/Venus Diamond flow. For the lab use Signum composite or Signum ceramis) according to the manufacturers instruction for use.
* With zirconia frameworks follow the steps in the same order, please use Signum zirconia bond instead of Signum metal bond.
6. Signum ceramic bond II ■ Apply the Signum ceramic bond II onto the ceramic and rub for 20 seconds to infiltrate. Remove the excess liquid.
■ According to manufacturers instructions for use the liquid by brush or airstream, not drying! The surface should remain moist, not too wet and not too dry.
2. Roughen the surface ■ Roughen the surface with the K1 drill with a speed of 6000 – 10000 revolutions per minute.
3. Cleaning the surface ■ Remove the impregnated debris with brush or oil free air and keep the surface dry.
4. Silanisation ■ Applying 1x thin layer Signum ceramic bond I and allow to evaporate (10 seconds).
5. Bonding ■ Apply 1x thin layer Signum ceramic bond II and rub for 20 – 30 seconds to infiltrate.
■ Remove excess liquid with a dry brush or use airstream. The surface should remain moist, not too wet and not too dry.
6. Repairing ■ Repair the defect area with direct composite (e. g. Venus Diamond/Venus Diamond flow) according to the instruction for use.
1. Straighten the fracture ■ Prepare the ceramic surface (if required) with a diamond bur under water cooling.
4. Signum opaque F ■ Apply Signum opaque F onto the metal and then light cure for 40 seconds e.g. Translux Power Blue.
45581_NCC_Signum_Bonding_Agents_Flyer_GB.indd 6-745581_NCC_Signum_Bonding_Agents_Flyer_GB.indd 6-7 25.07.13 15:0725.07.13 15:07
www.heraeus-kulzer.com
66
04
82
64
GB
07.
13
OR
T/R
M
In compliance with the European guideline 93/42/EWG our medical devices are CE-marked according to the classifications.
Contact in GermanyHeraeus Kulzer GmbHGrüner Weg 1163450 HanauGermanyPhone +49 (0)800-43 72 522Fax +49 (0)800-43 72 [email protected]
Contact in AustraliaHeraeus Dental Australia Pty LtdPO Box 40North Ryde BCNSW 1670AustraliaPhone +61 (0)2-84 22 61 00Fax +61 (0)2-98 88 14 [email protected]
www.heraeus-kulzer.com
Contact in the United KingdomHeraeus Kulzer Ltd.Heraeus House, Albert Road, Nothbrook Street, Newbury, Berkshire, RG14 1DLPhone +44 (0)1635-305 00Fax +44 (0)1635-524 [email protected]
Contact in KoreaHeraeus Kulzer Korea Co., Ltd.345-30 Gasan-dong,Geumcheon-gu,153-782 SeoulSouth KoreaPhone +83 (70)-7093-0707Fax +82 (2)-701-2492
45581_NCC_Signum_Bonding_Agents_Flyer_GB.indd 845581_NCC_Signum_Bonding_Agents_Flyer_GB.indd 8 25.07.13 15:0825.07.13 15:08
