Upload
moises-david-mejia
View
2.791
Download
6
Tags:
Embed Size (px)
Citation preview
Convenience in door opening
Automatic Card
authentication
Double authentication feature
(Pin & Card Key)
Force Lock features
Fire Alarm & Emergency
features
External anti-crime feature
www.EzonWorld.com
Product Parts (Outside)
Number Pad off
Touch the
number pad
Number Pad On
Number Pad
Battery lamp
Card Sensor
Reset Hole
Emergency
Battery terminal
Product Parts (Inside)
Number Pad
Number Pad
Registration button
Open button
Manual lock/unlock lever
Deadbolt
Door Open Sensor
Automatic/Manual Lock Mode switch
Open battery compartment cover
Press the battery compartment cover lightly then slide the
cover following the arrow direction
Opening the door from the outside (Pin Number). The double authentication mode is enabled
in default. To change the authentication process to normal mode please follow the instruction
below
Opening door outside (Pin Number)
1. Touch the number pad
2. Enter Pin Number
Double Authentication Mode
2 random numbers will
be lighted on the screen.
Press the 2 numbers
When the number pad
completely lights-up enter pin
number followed by [*] button
button
Bee~ree
~reep
Normal Authentication Mode Bee~ree
~reep
When the number pad completely lights-up enter pin number
followed by [*] button
-Enter pin number immediately when the number pad lights up,
when the number pad light turns off touch the number pad again
-When wrong pin number is entered, press the [House] icon and
enter correct pin
-5 consecutive failed pin entry will enable an alarm and the lock will
shut down for 3 minutes
Opening the door from the outside (Card, RF Key Tag) Automatic authentication mode is enabled in default, to switch mode to
Automatic/Manual authentication mode please refer to instructions below
Automatic
Mode
Manual Mode
Place card/key tag on the sensor and
the door will open within 1 second
Bee~ree~
ree
When the number pad lights up place
the card on the sensor Touch the number pad
In manual mode, touch the number pad
and place card on sensor
Opening/closing the door from the inside
Opening
Bee~ree~ree Bee~ree~ree
Closing
While the door is closed, Press
the [Open] button on the main
body and the door will open
Turn the manual lever to
[Unlock] position
In manual lock mode, while the
door is closed, press the [Open]
button and the door will close
Opening the door manually Closing the door manually
Turn the manual lever to [Lock]
position
Pin number Registration 4~12 digits can be registered, only 1 set of pin number can be registered
Press [Registration] button
Place card on sensor
Open battery compartment cover,
Press [Registration] button lightly Enter new pin number to be registered 4~12
digits, then press [*] button
Bee~ree~reep
For safety register at least 6 digits pin number (0~9)
numbers
New pin number registration will delete previously
registered pin number on the system
Register pin number while door is open
Card, Key Tag Registration Up to 20 cards can be registered
New registration will delete all previously registered pin number on the system
Please register all available RF key tags all-at-once
Press [Registration]
button
Open battery compartment cover,
Press [Registration] button lightly
Bee~ree~reep
Card registration complete
Place card to be registered on the
sensor
Bee~ree~reep
To complete the registration process, press the [Registration] button again
Register new pin number
Register all available card and key tags all at once. Place the card to be registered on the
sensor sequentially within the 10 second time frame or the card registration will complete
on it’s on. Always test authentication of newly registered cards.
Random Number Feature Setting This feature adds another layer of protection during pin number entry,
when enabled will add 2 random numbers together with the original pin
upon authentication
Beep~
Beep~
Open battery
compartment cover,
press pin number
Press [7] button to enable
Press [9] to disable
followed by [*] button
Double Authentication Mode Setting This security feature when enabled will require double authentication
which is the combination of Pin number and RF card entry.
When this is enabled RF card/key tag should be registered
Open battery compartment
cover, press pin number
Beep~
Press [4] button to enable
Press [6] to disable
followed by [*] button
Application
Touch number pad
Beep~
When the number pad
lights up, enter pin
number followed by [*]
button
Beep~
Place card on the sensor
and the door will open
Automatic/Manual Lock Mode Setting This setting will change the locking mode to automatic or manual mode
Located in the main body is the [A/M]
switch. Place the switch at [A] location for
automatic and [M] location for Manual
Automatic lock Mode – The door will lock within 2 seconds after
closing the door
Manual Mode - Press the [Open] button inside or touch the
number pad outside to lock the door
Sound Setting Melody guide during pin entry,door closing or opening can be adjusted to
desired volume, The melody guide is enabled in default.
Press [registration]
button
Set Volume
Open battery compartment cover,
Press [Registration] button once Press [0] button to mute
Press [1]~[3] button to
adjust sound followed by [*]
button
Bee~ree~
reep
Card,Key Tag Automatic/Manual Authentication Mode
Open battery
compartment cover, Press
[Registration] button once
Bee~ree~ reep
Press [5] button for automatic
Press [8] button for manual
Followed by [*] button
In automatic Mode place the card on the sensor and the door will
open, In manual mode place the number pad and put the card in
the sensor to open the door
Automatic Mode is enabled in default, but manual
mode consumers lesser battery
Force Lock Settings (Inside)
When enabled will not allow any entry from the outside
Enable Disable
Bee~ree
~ reep
Bee~
reep
Press [Open] button for 3
seconds Press [Open] button again
Application
Bee~reep
Touching the screen,Entering pin number or placing card
on the sensor will not open the door. Turning the manual
lever switch to open direction will open the door from
the inside
Force Lock Settings (Outside)
When enabled will not allow opening of the door from the
inside, When the [Open] button is pressed inside, an alarm
will go be activated.
Enable Disable
Press the[House] icon for 3
seconds and it is set Enter pin number followed by
[*] button, or place key tag
Replace Battery Notification
When the battery is about to be discharge, upon pin or card
entry, the replace battery alarm will be heard and the
battery lamp will be lighted
Replace Battery Please replace the battery within a week after hearing the alarm,
the lock will shutdown if disregarded.
Battery life depends on brand,usage and environment.
Normal battery last for 10 months
(based on 10 operations per day)
Please check for damage during battery replacement
External Emergency Battery Disregarding the replace battery alarm for a week will result the
battery to being discharged, And the lock to shut down completely.
Opening the door using the emergency battery Purchase a 9V battery and place the battery accordingly, refer
to the image below. In this position enter pin number or place
card on sensor to open the door
Security Alarms
Anti-Hacking Alarm – This security feature will activate a
series of alarm due to multiple failed pin number or card
authentication. And the lock will shut down for 3 minutes.
Force Break-in Alarm This security feature will enable an alarm if the lock senses
forceful entry
Fire Emergency Alarm
This security feature will enable an alarm if the lock senses
a high temperature of 60 degrees from the inside.
A series of alarm will be activated and the door will
automatically unlock.