Firearms
For the firearms shooting change the gain to low ( function 23)
or use with the paper target mounted in the front on device. The
target should be replaced after a few or over a dozen of
shoots.
The distance of firearms should be higher than 1 m.
Do not use to shootguns and black powder guns.
Connection to the computer
To transmision the data use HyperTerminal (Windows XP) or
TeraTerm. The chronograph connect via the USB-COM cable or
RS232.
In the program set the following transmission parameters: the
number of bits per second: 19200, data bits: 0, parity: none, stop
bits: 1, flow control: hardware.
Notes
After use, your responsibility is to provide equipment to the
designated collection point for the recycling of waste electrical
and electronic equipment
Do not leave for a long a time discharged batteries in the
device When measuring firearms - put the device out of reach
gases
Protect against water and moisture.
Functions
Measurement modes:1, 3, 4, 6, 8, 11, 12, 13, 14, 15, 16
S1 S2 S3
E= 12.8 JV= 221 m/s
S1 S2 S3
weight0.53g
S1 S2 S3
S1 S2 S3
Vsr225 m/s
S1 S2 S3
Vmin219 m/s
S1 S2 S3
S1 S2 S3
|dV|13 m/s
S1 S2 S3
SV10 m/s
S1 S2 S3
Esr13.2 J
S1
S2
S2
S2
S2
S2
S2
12
3
8
11
12
13
14
6
1
S3 1
S3 1
S3 1
S3 Erasing measurements
S3S2
weight of bullet
S1 S2 S3
lowbattery
5
low battery indicator
S3 1
S1
S3 1
S1
S1 S2 S3
MEMO:250R W CL
9
S1, S2, S3
Re
ad
ing
fro
m m
em
ory
an
d tra
nsfe
rrin
g d
ata
to
th
e B
UF
FE
RS3S2S1
Writin
g d
ata
of th
e
in
to th
e m
em
ory
BU
FF
ER
era
sin
g M
EM
OR
Y
the number free cell
the memory
t > 2 sec.
S1 S2 S3
gate5.00 cm
10
distance between sensors (only to calibration).
S2
S3
S1 1
S3
S1 S2 S3
V153221.4m/s
4
S3 1
S1 S2
S3
preview V[m/s]
S2
shoot153
S3
S1 S2 S3
V[fps]726
15
S1 S2 S3
V153726.3
16
S3 1
S1 S2
S3
Preview V[fps] in the BUFFER
t > 0.5 sec.
push S3
S2
S1 S2 S3
17
S2
RPS 00nr: 00
S1 S2 S3
18RPM 00nr: 00
S1 S2
S3 1
S3 1
S1 S2
erasing RPM, RPS, nr
erasing RPM, RPS, nr
18
Shooting speed
Read and writein to the memory
erasing RPM, RPS, nr
Vmax232 m/s
S1 S2 S3
20
Backlight on / offDisplay serial number
turn ondevice
S1push
S1 S2 S3
U1=4.75VU2=4.85V
21
Voltage of sensors
S2
S1
S1 S2 S3
bat
22
S1
S1push
S3
S3
S1 S2 S3
bat *
Programming “low battery indicator”
S1 S3
S2
Do not use it in normal exploatation. This point only for
service.
S2
push S2 turn ondevice
turn ondevice
BUFFER
tra
msm
isio
n to
co
mp
ute
r
turn ondevice
t > 0.5 sec.
automatically
sn601A0978
S1 S2 S3
GN: HIGH
23
Change gain: High ( air rifles )
S2
push S1, S2 turn ondevice
Notice: Each time you run this function, the gain will be
changed alternately
Change gain: Low ( firearms)
Strona 1Strona 2Strona 3
