Upload
others
View
7
Download
0
Embed Size (px)
Citation preview
SHIVAJI UNIVERSITY, KOLHAPUR,
B.E. (MECHANICAL ENGINEERING) Semester VII
Refrigeration and Air Conditioning
Teaching Scheme: Examination Scheme:
Lectures: 3 Hrs. per week Theory Paper: 100 Marks
Practical: 2 Hrs. per week Term Work: 25 Marks
Practical and Oral Exam: 25 Marks
Course Objectives:
1. Study of basic refrigeration cycles and Psychrometry. 2. Refrigeration and Air Conditioning Systems Performance Evaluation 3. To enable the students to analyze and solve refrigeration related problems by applying
principles of mathematics, science and engineering
Course Outcomes:
1. Students will demonstrate an understanding of the need and importance of HVAC
technology, the typical and some advanced and innovative schematic designs, and the goals of HVAC engineering and HVAC systems.
2. Students will demonstrate an understanding thermal comfort conditions with respect to temperature and humidity and human clothing and activities and its impact on human comfort, productivity, and health.
3. Students will demonstrate an understanding of psychrometrics and its application in HVAC engineering and design and will practice or observe psychrometric measurements.
4. Students will demonstrate an understanding of heat transfer in buildings with a given architectural design and its application to heating and cooling load estimation especially including thermal lag effects by conducting a detailed annual load analysis for a representative building and present the results of this analysis in a formal report possibly including recommendations for energy conservation.
5. Students will demonstrate an understanding of the engineering and operation of vapor
compression and possibly heat-driven refrigeration systems and evaporative cooling
systems and understand contemporary issues of ozone depletion and global warming
potential with respect to refrigeration systems.
Unit 1
Application of Second Law of Thermodynamics [03]
A Refrigerating Machine – The Second Law Interpretation, Energy Ratios(EER), BEE star rating
COP, Power Consumption of a Refrigerating Machine, Refrigeration Cycle, vapour as a
Refrigerant in Reversed Carnot Cycle Limitations of Carnot Cycle with Gas as a Refrigerant,
Reversed Brayton or Joule or Bell Coleman Cycle ,Introduction to aero-plane air conditioning
cycles (Only Theory)
Unit 02
Vapour Compression System [08]
Limitations of Reversed Carnot Cycle with vapour as a Refrigerant, Dry versus Wet
Compression, Throttling versus Isentropic Expansion, Vapour Compression Cycle, Pressure
Enthalpy Diagram and Calculations and effect of Operating Conditions, effect of Evaporator
Pressure Effect of Condenser Pressure, effect of Suction Vapour Superheat, effect of Liquid Sub
cooling, Using Liquid- Vapour Regenerative Heat Exchanger, Actual Vapour Compression
Cycle.
Removal of flash gas, Flash intercooling, Multistage, Multi evaporator and cascade system,
Choice of Intermediate Pressure , System Practices for Multistage Systems (Simple analytical
treatment) , Introduction to cryogenic Engineering and applications, Claude Cycle, Linde Cycle
Unit 03
Refrigerants and Refrigeration Equipments [09]
Classification, Desirable Properties like Thermodynamic, physical, & chemical. Comparison
among commonly used refrigerants, Selection of Refrigerants, Effect on Ozone depletion and
global warming, Alternative Refrigerants. Environmental Protection protocol & India’s
commitment. ASHRAE nomenclature.
Insulation, types and different applications, properties of ideal insulations.
Compressor, Condenser, Evaporator, Expansion devices, Types, selection. Component
balancing, safety devices and refrigeration controls.
Applications of Refrigeration, Ice plant, Cold storage, Dairy plant
Unit 04
Psychrometry and Human Comfort [09]
Moist air as a working substance, Psychrometric properties of air, Use of Psychrometric tables
and charts, Processes, Combinations and Calculations, ADP, Coil Condition lime, Sensible heat
factor, Bypass factor, Air washer and it’s applications.
Thermal exchange between human body and environment, factors affecting comfort, effective
temperature comfort chart, ventilation requirements.
Unit 05
Heating and Cooling loading calculations [05]
Design of air conditioning systems, different Heat sources,- Adiabatic mixing of two air
streams, sensible heat factor, RSHF, GSHF, ERSHF, Room apparatus dew point and coil
apparatus dew point, Ventilation and infiltration, Inside and Outside Design condition.
Cooling Load estimation, Introduction to Unitary Products viz. Room/Split and Packaged Air
Conditioners, Central air conditioning systems, Variable Refrigerant Flow systems, VAV control
systems, Inverter Units.
Unit 06
Air Distribution System [06]
Re-circulated air, Ventilation air, Duct work, Use of friction loss & rectangular equivalent of
round duct chart, duct system, principle of duct sizing, and air distribution it’s norms, diffusers,
dampers, layout, duct systems for theaters, auditorium, hospitals, assembly shop etc.,
Energy Conservations and Green Buildings, Freeze drying, Pharmaceutical and hospital air
conditioning, textile, car air conditioning (plant layout, system components and design
conditioning)
Term Work:
1. Study of various conventional and Nonconventional methods of refrigeration.
2. Study and demonstration of refrigeration system.(water cooler, refrigerators, chiller, ice plant and
cold storage).
3. Study of Refrigeration tools.
4. Trial on Refrigeration Test Rig.
5. Trial on heat pump test rig.
6. Study and trial on vapour absorption system
7. Trial two stage cascade system.
8. Trial on ice plant test rig
9. Study and demonstration on air conditioning systems. (Unitary and central air conditioning /
system)
10. Trial on window air conditioner or Air Conditioning Test Rig
11. Study or demonstration of dehydration, charging leak testing and testing of refrigeration system
with trouble shooting.
12. Study and demonstration of controls and safety devices in refrigeration and air conditioning.
13. Visit to central air conditioning or cold storage or dairy plant to ice plant related with
refrigeration & air conditioning system.
14. Market survey of various refrigeration and air conditioning systems which include the equipments
with related specifications, manufacturers, cost and comparison with respect to tonnage, coat and
presentation of report in the laboratory.
(Three trials and market survey report is compulsory/ Total 10 are compulsory)
Reference Books:
Basic refrigeration and air conditioning- P N Ananthanarayan
Principles of Refrigeration - Roy J. Dossat
Refrigeration and Air Conditioning - Stoker
Refrigeration and Air Conditioning - C. P. Arora
Refrigeration and Air Conditioning - AroraDomkundwar
Refrigeration and Air Conditioning - V. K. Jain
Air Conditioning Principles and Systems - Pita
Air Conditioning Applications and Design - W. P. Jones
Air Conditioning Engineering - W. P. Jones
Thermal environmental engineering - Tnerellaild
Text Book: Arora C. P. “Refrigeration and Air Conditioning”, Tata McGraw-Hill Publishing Company Ltd., New Delhi, 1981.
SHIVAJI UNIVERSITY, KOLHAPUR,
B.E. (MECHANICAL ENGINEERING) Semester VII MECHANICAL SYSTEM DESIGN
Teaching Scheme: Examination Scheme:
Lectures: 3 Hrs/Week Theory: 100 marks
Practical: 2 Hrs/Week Term Work: 25 marks
Oral Exam: 25 marks
Course Objectives 1. To study the concept of Aesthetics, Ergonomics and creativity considerations in product
design.
2. To study design of various mechanical systems such as Pressure vessel, Brakes, Clutches, Machine tool Gear box, I.C. Engine components etc.
3. To study the concepts of optimization of mechanical systems /elements.
Course Outcomes: After completion of the course , the student will be able to
1. Incorporate Aesthetic, Ergonomic and creativity considerations in industrial product design.
2. Design different systems such as Pressure vessel, Brakes, Clutches, Machine tool Gear box and I. C. Engine components etc.
3. Optimize design of various components/systems in mechanical engineering 4. Use IS Codes, Design data books, Handbooks required for system design .
UNIT 1
Aesthetic and Ergonomic consideration in Design: 06
Basic types of product forms, designing for appearance, shape, Design features, Materials,
Finishes, proportions, Symmetry, Contrast etc. Morgon’s colour code. Ergonomic
considerations- Relation between man, machine and environmental factors. Design of displays
and controls. Practical examples of products or equipments using ergonomics and aesthetic
design principles. Creativity concept in designing.
UNIT 2
Pressure Vessel Design: 07
Thin and thick cylinders; failure criteria of vessels; Lame’s equation; Clavarino’s and Birnie’s
equation; Autofrettage and compound cylinders; Types of pressure vessels-Horizontal and
vertical; Classification of pressure vessel as per IS2825, 1969.Introdduction to design of pressure
vessels as per IS Codes. Shell and end closures. Effect of opening and nozzles in shell and
covers. Types of pressure vessel support.
UNIT 3
Design of Braking and Clutch System. 07
A) Brakes: Design consideration in brakes, Band, Internal expanding shoe, External contracting
shoe. Thermal consideration and rating of brakes.
B) Clutches: Design requirement of friction clutches, Selection criteria. Torque transmitting
capacity of single plate, Multidisc clutch, Cone clutch and Centrifugal clutch.
UNIT 4
Design of Gear boxes for machine tool applications 07
Determination of variable speed range- Graphical representation of speeds- Structure diagram-
Deviation diagram- Ray diagram- Selection of optimum ray diagram- Difference between
number of teeth of successive gears in a change gear box- Analysis of twelve speed gear box-
Compound ray diagram
UNIT 5
Design of I. C. Engine Components 07 Introduction to selection of material for I. C. engine components, Design of cylinder and cylinder
head, Design of cylinder liners, design of piston and piston-pins, piston rings, design of
connecting rod, design of crank-shaft and crank-pin.
UNIT 6
Optimum Design 06
Objectives of optimum design- Johnsons Method of Optimum Design (MOD), Adequate and
optimum design. Primary, Subsidiary and Limit equations- Optimum design with normal
specifications of simple machine elements like tension bar, transmission shaft, helical spring.
Introduction to optimum design with Langrange Multiplier.
TERM WORK
1) A detail design report and A2 size sheet containing working drawing of detail and assembly of
the following
a) Design of Machine Tool Gear Box.(Three Stage, Twelve speed gear Box) b) Pressure vessel design/ Brake design or Clutch design.
2) Assignment based on
a) Aesthetic and Ergonomic design consideration –case study b) Problems on Optimum design. c) Minimum four Problems on Design of IC Engine components. such as connecting rod,
crank shaft, piston with piston rings and pins, cylinder and cylinder head.
Text Books:
1. Design of machine element by V.B.Bhandari, Tata Mc- Graw Hill Publication 2. Mechanical Engineering Design by Shigley and C.R.Miscke, Tata Mc- Graw Hill 3. Publication 4. Mechanical design analysis by M.F.Spotts, Prentice Hall publication 5. Design of machine Tools by S.k. Basu and D.K. Pal Oxford And IBH Publication. 6. Machine Tools Design by N.K. Mehta, Tata Mc- Graw Hill Publication. 7. Design data PSG College of Technology Coimbatore 8. I.S.:2825 Code for unfired Pressure Vessels
Reference Books 1. Handbook of gear design by Jitin Maitra,Tata Mc-Graw Hill Publication. 2. Machine Design by Black P.H.and O.Eugene Adams, Tata Mc- Graw Hill Publication 3. Mechanical Design Synthesis with Optimisation Applications by Johnson R.C.,Von-
Nostrand-Reynold Publicaion
4. Engineering Design by Dieter G.E. Tata Mc- Graw Hill Publication.
5. Mechanical System Design by S.P.Patil, Jaico Publication House,New Delhi 6. Product design and process engineering –Benjamin W. Niebel , Alan B. Draper, Tata
Mc- Graw Hill Publication
7. Design of Pressure vessel by Harve, CBS publishers and distributors 8. Engineering Optimization Theories and Practice by S.S.Rao, New Age Publication 9. Process Equipment Design by M.V.Joshi , Macmillal Publication 10. Machine Design by Robert L.Norton, Tata Mc- Graw Hill Publication 11. Machine Design by p. Kannaiah Scitech Publication. 12. Fundamentals of Machine Component Design by Junvinall Wiley India 13. Mechanical System Design by Anurag Dixit SCITECH publication 14. Principles of machine tool by Sen. Bhattacharya, New central book agency
SHIVAJI UNIVERSITY, KOLHAPUR,
B.E. (MECHANICAL ENGINEERING) Semester VII
3. Finite Element Analysis
Teaching Scheme: Examination Scheme:
Lecturers: 3 Hrs/ Week Theory: 100 Marks
Practical: 2 Hrs/ Week Term work: 25 Marks
Course Objective:
a. To define the basic finite element formulation techniques.
b. To derive the finite element equations for 1D, 2D and 3D problems.
c. To formulate and solve basic problems in Heat Transfer, Solid Mechanics and Fluid Mechanics.
d. To develop the computer program based on Finite Element Methods.
e. To use commercial software’s to solve Basic Engineering problems in Heat Transfer, Solid
Mechanics and Fluid Mechanics.
Course Outcome:
After completion of the course , the student will be able to a. Elaborate the fundamental concepts, equations of equilibrium, Stress-strain relations and the
principle of potential energy and approximations of differentials equations.
b. Develop the key concepts of finite element formulations by considering the 1D problem just as Shape function, element stiffness and boundary conditions.
c. Apply the finite element formulations for two dimensional plane stress and plane strain problems using constant strain triangle.
d. Demonstrate the modelling aspects of axisymmetric solids subjected to axisymmetric loading.
e. Understand the Galerkin formulation for steady state heat transfer, torsion and potential flow.
Unit 1: Fundamental Concepts 7
Introduction, Past, present and future of FEA, stresses and Equilibrium, boundary
conditions, strain-displacement relations, stress-strain relations, Temperature effects,
Potential energy and equilibrium; the Rayleigh-Ritz method, Galerkins method, Saint-
Venant’sprinciple, Von-Misesstress, Gauss elimination method.
Unit 2: One Dimensional Problem 6
Introduction, Finite element modelling(element division, numbering scheme), coordinates
and shape functions, the potential energy approach(element stiffness matrix, force terms),
Galerkinapproach (element stiffness matrix, force terms),Assembly of the global stiffness
matrix and load vector, properties of K, the finite element equations; treatment of
boundary conditions(types of boundary conditions, elimination approach, penalty
approach (Theoretical concept only), multipoint constraints, Quadratic shape functions.
Unit 3: Two-Dimensional Problems using Constant Strain Triangles 6
Introduction, finite element modelling, Constant Strain Triangle (CST), Iso-parametric
representation, potential-energy approach, element stiffness, force terms,
Galerkinapproach, stress calculations, problem modelling and boundary conditions
Unit 4: Axisymmetric solids subjected to axisymmetric loading and Analysis of Trusses 8
Introduction, axisymmetric formulation, finite element modelling, triangular element,
potential energy approach, body force term, rotating flywheel, pressure vessel,
Galerkinapproach, stress calculations.
Trusses:-Plane trusses, Local and Global coordinate systems, formulas for calculating L
and M, element stiffness matrix, Stress Calculations, Assembly of global stiffness matrix.
Unit 5: Scalar Field Problems 6
Introduction, steady state heat transfer, One dimensional heat conduction, One
dimensional heat transfer in thin fins, Two dimensional steady state heat conduction, two
dimensional fins.
Unit 6: Computer Implementation of the Finite Element Method: 7
Pre-processing: Model definition – nodal coordinates element connectivity, material and
element type and property definitions, type of analysis (static/modal), loading and
boundary conditions. Meshing techniques- free and mapped meshing, Quality checks –
aspect ratio, warp angle, skew, distortion, stretch, included angle, taper
Processing: Element level calculations, Equation assembly, Equation solver (sparse
solvers, factorization, numerical/computational issues)
Post Processing: Strain and stress recovery (integration and nodal points), interpretation
of results (results validation and data interpretation) and design modification
TERM WORK
1. One assignment on past, present and future of FEA.
2. One assignment on Meshing – types of elements, choice of element, type of meshing –automatic,
mapped, meshing in critical areas.
3. Finite Element Analysis of Stepped bar (Two or Three Steps only) using
a) Finite Element Approach (Theory)
b) Finite Element Software (ANSYS / ABACUS / NISA / NASTRAN etc)
c) Computer Program using C or C++
Compare the results by above three methods in tabular form.
4. Use of any ONE Standard software packages like ANSYS, NISA, NASTRAN, HYPERWORKS
for solving following types of problems with snap shots of software ( Any FIVE)
Static Analysis of Truss
Static Analysis of Beam
Static Analysis of Plate with a circular hole
Static Analysis of Wall Bracket
Buckling Analysis of Column
Analysis of 1D or 2D Fin
TEXT BOOKS:
1. “Introduction to Finite Elements in Engineering”; Chandrapatala, Belgundu, PHI. 2. “Finite Element Method with Application in Engineering” Y. M. Desai, T. I. Eldho, A. H.
Shah, Pearson.
3. “Textbook of Finite Elements Analysis”, P. Sheshu, Prentice-Hall of India Private Limited, New Delhi.
4. “An Introduction to Finite Element Method”; J. N. Reddy; 2/e, McGraw Hill International Editions, ISBN 0-07-112799-2
5. “Finite Element Methods for Engineers”; U.S. Dixit, Cengage Learning. 6. “Finite Element Analysis – Theory and Practice”; M.J. Fagan, Longman Scientific
&Technical.
REFERENCE BOOKS:
1. “The Finite Element Method – Basic Concepts and Linear Applications”; O. C, Zienkiewicz; McGraw Hill International Editions; ISBN 0-07-084175-6
2. “Practical Finite Element Analysis”, N.S. Gokhale, S.S. Deshpande, S.V. Bedekar, A.N.Thite, Finite to Infinite Publication.
3. “Concepts of Finite Element Methods”,Manicka Selvam, SCITECH publication 4. “A First Course in the Finite Element Analysis”, D.L.Logan,CengageLearning 5. “Finite Elements Analysis – Theory and Application with ANSYS, Sawed Moveni, Prentice-
Hall Inc.
6. “Applied Finite Elements Analysis”, Larry J. Segerlind, BSP Books Pvt Ltd.
WEBSITE REFERENCE:
1. University of Alberta Tutorials from website 2. NPTEL Videos Lecture series
SHIVAJI UNIVERSITY, KOLHAPUR,
B.E. (MECHANICAL ENGINEERING) Semester VII
Experimental Mechanics (Elective I) Teaching Scheme: Examination Scheme:
Lectures: 3 Hr/Week Theory: 100 Marks
Practical: 2 Hr/Week Term Work: 25 Marks
Course Objectives:
1. To introduce the concept of elementary elasticity and experimental stress analysis
2. To prepare Mechanical Engineering students for advanced graduate studies in various
experimental stress analysis techniques like Photo Elasticity, strain gauge
3. To supply qualified personnel to meet the requirement of specialist in Experimental
Stress Analysis
Course Outcomes:
At the end of the course, student will be able to
1. Analyze photo elastic technique to stress analysis
2. Explain the concept of strain gages and it applications
3. Elaborate the concept of coating methods.
4. Apply the knowledge of Moiré fringe method of stress analysis.
Syllabus
1. Principles of Experimental Approach- 03
Introduction to Experimental Mechanics, advantages scope of Experimental Mechanics in
design, various experimental methods of stress analysis and their relative merits and
demerits
2. Two Dimensional Photoelasticity- 11
optics related to photoelasticity, temporary and permanent double refraction,
principle of photoelasticity, method of photoelastic stress analysis
stress optics law, material fringe value in terms of stress and strain, significance of
material fringe value
polariscope, its scope in photoelasticity, various configurations of polariscope
effect of stressed model in plane and circular polariscope, isoclinics, isochrometics,
their significance in photoelastic stress analysis, fringe order, use of white light in
photoelasticity
fractional fringe measurement methods- color matching techniques, compensation
methods like babinet soleil compensation method and Tardy’s method (Derivation)
3. Analysis of Photoelastic Data – 06
Determination of direction of principal stress at a given point, determination of exact
fringe order N and difference of principal stresses at a given point, shear difference
method, oblique incidence method and electrical analogy method.
Photoelastic Materials - Criteria for selection, common photoelastic materials and their
properties, Photoelastic sheet casting and model making, calibration of photoelastic
material, calibration methods using circular disc
4. Strain Measurement Using Strain Gauges– 07
Concept, meaning of strain gauge, desirable properties of strain gauges, types of strain
gauges, comparison of various strain gauges Strain measurement using electrical
resistance strain gauge –Introduction, principle, types, construction, materials used in
construction, sensitivity, gauge factor, cross sensitivity, semiconductor strain gauge,
comparison with electrical resistance strain gauge, advantages and limitations Selection
and mounting of strain gauge, criteria for selection, mounting of gauge and checking its
installation
5. Strain Gauge Circuitry – 07
Wheatstone bridge circuit, its role in measurement of resistance change, condition for
bridge balance, different configurations of Wheatstone bridge, output voltage of
Wheatstone bridge, relationship between output voltage and strain, commercial strain
indicators, potentiometer circuit. Introduction to strain gauge rosettes, two, three and four
element rosettes, different configurations of rosettes and their comparison, determination
of magnitudes and direction of principal stresses when principal stress directions are
specified and not specified. Transducer applications of strain gauge
6. Coating Method and Moire Fringe– 06
Brittle coating, Introduction, interpretation of crack pattern data, crack detection
techniques, selection of brittle coating, advantages, Birefringent coating:- Limitations and
applications, Introduction to Birefringent coating, use of reflection polariscope, merits
and demerits
Introduction to Moiré fringe method of stress analysis – Mechanism of fringe formation,
approaches to moiré fringe analysis, advantages, limitations and applications
TERM – WORK
Any Eight out of the following list
1. Bonding of strain gauge and checking its installation
2. Determination of gauge factor for one arm sensitive and two arm sensitive configuration
3. Determination of gauge factor for four arm sensitive and four arm sensitive two linear
and two lateral configuration
4. Transducer applications of strain gauge- determination of unknown weight using load
cell
5. Transducer applications of strain gauge – determination of unknown torque using torque
transducer
6. Study of photoelastic stress analysis – use of diffused light transmission polariscope
7. Determination of fractional fringe order using Tardy’s method
8. Calibration of photoelastic materials - determination of material fringe value
9. Separation of stresses using oblique incidence method
10. Study of Moiré Fringe Technique. 11. Study of Brittle Coating Method. 12. Study of Photoelastic materials.
TEXT BOOKS
1. Experimental Stress Analysis by Dr. Sadhu Singh; Khanna Publishers
2. Experimental Stress Analysis by U.C. Jindal, Pearson Publications
3. Experimental Stress Analysis by Abdul Muben; DhanpatRai& Co.
4. Experimental Stress Analysis by Vazirani, Khanna Publications
5. Stress Analysis and Experimental Techniques an Introduction by J. Srinivas, Narosa
Publications.
REFERENCE BOOKS
1. Experimental Stress Analysis by J.W. Dally &W.F.Riley, McGraw Hill Book Company
2. Principles of Experimental Stress Analysis by Asm, American Society for Metals
3. Experimental stress analysis – L.S.Srinath., Tata McGraw Hill 4. Experimental stress analysis – Dove and Adams 5. The strain gauge primer – Perry Listner 6. Moiré fringes – Theocoris. Pergamon press limited. 7. Experimental Stress Analysis Principles and Method by Holister G.S., Cambridge
SHIVAJI UNIVERSITY, KOLHAPUR, B.E. (MECHANICAL ENGINEERING) PART-I
ELECTIVE -I HUMAN VALUES AND PROFESSIONAL ETHICS
Teaching Scheme Examination Scheme
Lecturers: 3 Hrs/ Week Theory: 100 Marks
Practicals: 2 Hrs/ Week Term work: 25 Marks
Course Objectives
The objective of the course is an exploration of human values which go into making a
good human being, a good human society and a good life. The context is the work life and the personal
life of modern Indian professionals. The movement to identify and romote the values shared by societies
around the world is relatively new. It is only in recent years as globalization extended its reach to even
remote corners of the earth that he need to refocus and build upon what we as a human society have in
common, has become apparent. Increased contact between peoples and nations enhances awareness f our
kinship and the shared code of ethics and conduct that underlies all civilization. It s he Human values that
we must now promote to create a common vision and means for moving forward toward a more peaceful
and sustainable world.
The course also aims to have students appreciate the vastness of the Universe and the wonder of
its parts, and the philosophical significance of this for improving the quality of human life through value
clarification.
Course Outcomes (Student Learning Outcomes) Students will demonstrate in college level writing
an understanding of the role of cognitive and moral values in world views, by discussing and writing about the ethical implications of modern scientific and technological results
a recognition of the difference between matters of fact and matters of value, while understanding the important ways in which facts influence value assessments and how value judgments shape
our vision of "the facts"
an understanding of ethical methodologies and competency in ethical deliberation on rationally applying these methodologies to contemporary ethical questions related to scientific progress and
technological power
an understanding of ethical why ethics plays an important role in science and technology
1. HUMAN VALUES (10)
The value-crisis in the contemporary Indian Society-The Indian system of values-Values in the Indian
constitution-Aesthetic values: perception and enjoyment of beauty-Relative and absolute values-Morals-
Values and Ethics – Integrity-Service – Work Ethic –Service Learning – Civic Virtue – Respect for
Others –Respect for the Environment-Quest for Living Peacefullyand happily–Attitude of Nonviolence-
Innate dignity for human life – Bring out the best in oneself -caring – Sharing – Honesty – Courage –
Valuing Time – Co-operation – Commitment – Empathy – Self-Confidence – Character – Spirituality
2. ENGINEERING ETHICS ( 8 )
Senses of 'Engineering Ethics' - variety of moral issued - types of inquiry - moral dilemmas - moral
autonomy - Kohlberg's theory - Gilligan's theory - consensus and controversy – Models of Professional
Roles - theories about right action- Self-interest - customs and religion - uses of ethical theories.
3. ENGINEERING AS SOCIAL EXPERIMENTATION (7)
Engineering as experimentation - engineers as responsible experimenters - Research Ethics - codes of
ethics - a balanced outlook on law - the challenger case study
4. SAFETY, RESPONSIBILITIES AND RIGHTS (7)
Safety and risk - assessment of safety and risk - risk benefit analysis and reducing risk - The Government
Regulator’s Approach to Risk- the three mile island, Chernobyl and Bhopal case studies. Collegiality and
loyalty - respect for authority - collective bargaining - confidentiality -conflicts of interest - occupational
crime - professional rights - employee rights - Intellectual Property Rights (IPR) - discrimination.
5. GLOBAL ISSUES (8)
Multinational corporations - Business Ethics -Environmental ethics –Role in Technological
Development- computer ethics - weapons development
- engineers as managers-consulting engineers-engineers as expert witnesses and advisors -Honesty-moral
leadership-sample codes of Ethics like ASME, ASCE, IEEE, Institution of Engineers (India), Indian
Institute of Materials Management, Institution of electronics and telecommunication engineers (IETE),
India,etc.
TERM WORK
The term work should be carried out with the methodology of lectures, group discussions(based on case
studies), movies, field visits, essays and student self investigation sessions.
1. TEN modules based on the topics mentioned above and Including –
Group Discussions on Case Studies with report/Essays .
Undergoing the Art of Living’s YES+ / Happiness Programme on the Awareness of Human Values conducted by Vyakti Vikas Kendra ,Bangalore in assistance with INTERNATIONAL
ASSOCIATION OF HUMAN VALUES. (IAHV).
Visits (with report writing) to Public Institutes like Municipal Corporation,ZP, Co-op organizations, social clubs like charitable trusts, Waste Water/Air Pollution Control Plant,
Slum Areas etc.
Conduction of Health and Hygiene Awareness Camp for Society.
Study of economic status of the society –Survey data collection, analysis and any suggestions.
Study of impacts of technology on society.
TEXT BOOKS
1. Professional Ethics and Human Values by M.P. Raghavan,Scitech Publications (India) Pvt Ltd 2. Human Values and Professional Ethics by Jayashri and Suresh B S ,S Chand . 3. Mike Martin and Roland Schinzinger, “Ethics in Engineering”, McGraw-Hill, New York 1996. 4. Govindarajan M, Natarajan S, Senthil Kumar V. S, “Engineering Ethics(Including Human
Values)”, Prentice Hall of India, New Delhi
5. A Textbook on Professional Ethics and Human Values by Naagarazan, R.S. ,New Age Publishers .
6. Professional Ethics and Human Values by A Alavudeen,R Kalil Rahman M Jayakumaran ,Laxmi Publisher .
7. Understanding Human Values :Individual and Societal by Milton Rokeach ,Free Press Publication .
8. Human Values by A N Tripathy, New Age International . 9. A Foundation Course in Value Education by R R Gaur,R Sangal,2009 10. Science and humanism by P L Dhar and R R Gaur, Commonwealth Publishers 11. “Wisdom for The New Millennium” by H.H .Sri Sri Ravishankarji, founder ,Art Of Living,
Vyakti Vikas Kendra, Bangalore.
12. “The Monk Who Sold his Ferrari” by Robin Sharma, Jaico Publishing House . 13. “Mega Living” by Robin Sharma, Jaico Publishing House . 14. The Story of Phillosophy by W,Durant . 15. “The first and the Last Freedom” by Osho.
16. Commentaries on living by J Krishnamurti 17. The Rebirth of Buddha by Ryuho Okawab Paperback – 2009 , Happy Science; Second
(Revised) Edition.
18. Speeches and writings of Swami Vivekananda; a comprehensive collection, G. A. Natesan & Co., Madras.
REFERENCE BOOKS:-
1. Charles D. Fleddermann, “Engineering Ethics”, Pearson Education / Prentice Hall, New a. Jersey, 2004 (Indian Reprint now available).
2. Charles E Harris, Michael S. Protchard and Michael J Rabins, “Engineering Ethics –Concepts 3. and Cases”, Wadsworth Thompson Leatning, United States, 2000 (Indian Reprint now available) 4. John R Boatright, “Ethics and the Conduct of Business”, Pearson Education, New Delhi, 2003. 5. Edmund G Seebauer and Robert L Barry, “Fundamentalsof Ethics for Scientists and Engineers”,
Oxford University Press, Oxford
6. Prof. (Col) P S Bajaj and Dr. Raj Agrawal, “Business Ethics – An Indian Perspective”, Biztantra, New Delhi, (2004)
7. Science and the Human Prospect, by Ronald C. Pine Brave New World by Aldous Huxley 8. Society ,Environment and Engineering by H R Mukhi , Birla Publications, New Delhi 9. Society, Environment and Engineering by R Agor, Satya Prakashan,New Delhi
Relevant CDs ,Movies ,Documentaries and Websites
www.onlineethics.org, www.storystuff.com, www.iahv.org , www.5h.org , www.artofliving.org
, www.ijhvpe.com, Al Gore,An Inconvinient Truth, Paramount classics USA Charlie Chaplin, Modern Times,United Artits ,USA IIT Delhi, ModernTechnology-The Untold Story
http://www.amazon.com/Ryuho-Okawa/e/B00IVYN554/ref=dp_byline_cont_book_1http://www.onlineethics.org/http://www.storystuff.com/http://www.iahv.org/http://www.5h.org/http://www.artofliving.org/http://www.ijhvpe.com/
SHIVAJI UNIVERSITY, KOLHAPUR,
B.E. (MECHANICAL ENGINEERING) PART-I
ELECTIVE -I AUTOMOBILE ENGINEERING
Teaching Scheme Examination Scheme Lectures: 3 Hrs/ Week Theory: 100 Marks
Practical: 2 Hrs/ Week Term work: 25 Marks
Unit 1. Introduction (6)
Automobile history and development, Classification, vehicle layouts- engine location and drive
arrangement, safety regulations, specifications of vehicles, Type of vehicle bodies, body parts and its
advanced materials, Chassis types, constructional details, Types of Frames, sub frames, frameless
vehicles, details of chassis material, Vehicle life development cycle overview.
Unit 2. Transmission System (6)
Clutch – Function and requirements, Classification, Construction and working of Single-plate, Multi-
plate, diaphragm spring and centrifugal clutches, Fluid flywheel.
Gear Box – Necessity, classification, construction of manual gear boxes like Sliding mesh, constant mesh,
Synchromesh, Epicyclic gear train, automatic transmission, Torque convertor, Electronic transmission
control, overdrive. Propeller shaft, Differential and final drive.
Unit 3. Steering & Suspension Systems (8)
Live and dead axles, live axle arrangement.
Steering systems, function, principle of steering, Ackerman and Davis, steering geometry, center point
steering, cornering force, slip angle, scrub radius, steering characteristic, steering gearbox, power
steering, collapsible steering.
Suspension system- Functions, Sprung and unsprung mass, Types of suspension linkages, types of
spring - leaf, coil, air springs, telescopic shock absorber, hydro gas suspension, rubber suspension,
interconnected suspension, self-leveling suspension (active suspension) Advances in suspension system,
Air suspension
Unit 4. Brakes, Wheels and Tyres (7)
Brakes: Need, principle, types, Mechanical, hydraulic and pneumatic brakes disc and drum types, air
brakes, servo and power braking, ABS, their relative merits, details of components, brake adjustments,
defects and causes.
Wheels and Tyres: Wheel construction, alloy wheel, Types, tyre construction, tread design, specification,
factors affecting tyre performance, tyre wear and its causes, wheel balancing.
Unit 5. Electrical and Electronic Systems (7)
Automotive batteries - lead acid batteries, Advances in batteries ,battery charging system, alternators,
principle and operation of cutout and regulators, starter motor, Bendix drive, solenoid drive, magneto coil
and solid stage ignition systems, lighting and electrical accessories, automobile air conditioning, panel
board instruments. Electronic controlled management systems (ECM), Automobile wiring. Sensors used
in automobile.
Unit 6. Performance of Automobiles (6)
Resistance to vehicle motion, Air, Rolling and Gradient resistance, Acceleration, Gradability and draw
bar pull, Traction and Tractive effort, Distribution of weight, Power required for vehicle propulsion,
Selection of gear ratio, Rear axle ratio. (Numerical)
TERM WORK
Minimum eight experiments from Group A and all experiments from Group B are to be performed.
Group A.
1. Study and demonstration of four wheeler chassis layout and vehicle body parts and its materials. 2. Study and Demonstration of working of single plate automobile clutch and clutch plate lining
materials.
3. Study and demonstration of synchromesh gearbox. (necessity, interlocking mechanism, gear shifting mechanism (Troubleshooting)
4. Study and demonstration of final drive and differential. (Types of final drive gear, Troubleshooting)
5. Study and demonstration of front wheel steering geometry and steering mechanism. (Troubleshooting)
6. Study and demonstration of suspension system of a four-wheeler. (Any one suspension system from conventional or independent, troubleshooting)
7. Study and demonstration of working Hydraulic braking system. (Air bleeding of hydraulic brake, Troubleshooting)
8. Study and demonstration of Lead acid Battery. (Troubleshooting) 9. Study and demonstration of electrical charging system. (Troubleshooting) 10. Study and demonstration of electrical starting system.(Troubleshooting) 11. Study and demonstration of
a) D. C. Electric horn b) Electric fuel Gauge c) Flasher unit. d) Wiper circuit 12. Study of automobile air conditioning system.
Group B.
1 Experiment on wheel balancing & front wheel alignment.
2 Visit to servicing station for study of vehicle maintenance, repairs and report.
OR
2. Visit to Automobile manufacturing industry.
Text Books:
1. Automobile Engineering, Dr. Kirpal Singh (Vol. I & II ) Standard Publishers 2. Automobile Mechanics, N K Giri 3. Automobile Engineering, G.B.S. Narang. 4. Automotive Technology, H.M. Sethi. 5. Automobile Engineering, Banga & Singh 6. Automotive Mechanics, Joseph Heitner, 2nd Ed., Affiliated Eastern Law house, 1967. 7. Motor Vehicle Technology and Practical Work, Dolan. J.A., ELBS, 1978 8. Automobile Electrical Equipment, P.L.Kohali 9. Automobile Engineering, R.B.Gupta 10. Automotive Excellence volume 1 & 2, Gelncoe, McGraw-Hill
Reference Books:
1. Motor Vehicles, Newton & Steed 2. Motor Manuals (Vol I to VII ), A.W. Judge. 3. Automobile Mechanics, W.H. Crouse. McGraw Hill Publishing Co.
SHIVAJI UNIVERSITY, KOLHAPUR,
B.E. (MECHANICAL ENGINEERING) PART-I
ELECTIVE -I COMPUTATIONAL FLUID DYNAMICS
Teaching Scheme Examination Scheme Lectures: 3 Hrs/ Week Theory: 100 Marks
Practical: 2 Hrs/ Week Term work: 25 Marks
1. Introduction to Computational Fluid Dynamics & Principles of Conservation (8)
Computational Fluid Dynamics: What, When, and Why? CFD Applications, Numerical vs. Analytical vs.
Experimental, Modeling vs. Experimentation, typical problems, Problem Solving with CFD —
Methodology, The Governing Equations of Fluid Dynamics & Heat transfer, Models of the flow- Control
Volume, Fluid Element, Substantial Derivative, Divergence of Velocity, Continuity Equation Different
Models and their Equivalence, Integral versus Differential Form of the Equations, The Momentum
Equation, The Energy Equation, Summary Equations for Viscous Flow (the Navier-Stokes Equations)
Equations for Inviscid Flow (the Euler Equations) Forms of the Governing Equations Particularly Suited
for CFD
2. Basic of discretization & Grid generation (6) Basic aspects of discretization - Discretization techniques Finite difference - Finite volume and Finite
element method Comparison of discretization by the three methods, Transformation of non-uniform grids
to uniform grids - General transformation of the equations -Form of the governing equations suitable for
CFD - Compressed grids - Boundary fitted co-ordinate systems Elliptic grid generation - Adaptive grids -
Modern developments in grid generation.
3. Finite Difference Method (6) Finite Difference Formulations: Introductory remarks, Taylor Series Expansions,. Finite difference
equations, Central Forward, Backward Numerical error, Explicit, Implicit, Semi-implicit(Crank-
Nicholson method), Solution methods Direct, Iterative, Thomas algorithm, Gauss- Jacobi, Gauss- seidal
method, Alternate Directional Implicit, Applications. 1-D examples, 2-D examples.
4. Finite Volume Method (8)
i. For Diffusion
Introduction, FVM for 1D steady state Diffusion, FVM for 2 D Diffusion
ii. For Convection Diffusion
Introduction, Steady 1-D Convection and Diffusion, Central Differencing, Upwind Differencing,
Hybrid Differencing, Power Law Scheme, QUICK scheme.
5. Introduction to solution algorithms for pressure velocity coupling in steady flows & turbulence
and multiphase modeling (Introductory treatment) (6) Introduction, staggered grid, introduction to SIMPLE, SIMLEC, SIMPLER, PISO algorithms,
Modeling of multiphase problems, Level set methods, VOF method. Coupled LS+VOF.
6. Introduction to Turbulence and its modeling (6) What is turbulence?; Transition from laminar to turbulent flow; Effect of turbulence on time averaged
Navier -Stokes equations; Characteristics of simple turbulent flows; Introduction to Turbulent Models
like Mixing length Model, k-epsilon model, Reynolds stress equation models, Algebraic stress
equation models; Some recent Advances, introduction to LES, DNS.
Term Work 1. Simulate and solve two problems, each 2-d and 3-d steady and unsteady flows using any
commercial CFD package like Ansys-FLUENT, STAR CCM, FLUIDYNE, Ansys-CFX etc.
2. Write codes using C, C++, SciLab for at least one each, 1-d and 2-d steady flows and do the post processing to verify with analytical results.
SHIVAJI UNIVERSITY, KOLHAPUR, B.E. (MECHANICAL ENGINEERING) PART-I
ELECTIVE -I Process Equipment Design
Teaching Scheme: Examination Scheme:
Lectures: 3 Hrs/Week Theory: 100 Marks
Practical: 2 Hrs/Week Term Work: 25 Marks
Course Objectives :
1. To acquaint several design codes used in the design process.
2. To study design of process equipment such as pressure vessel, storage tank, heat exchanger etc.
Course Outcomes :
After completion of the course , the student will be able to
1. Illustrate understanding of process design parameters.
2. Design and develop pressure vessels.
3. Demonstrate capabilities developed for designing storage tank, agitators.
Unit-1 Process Design Parameters Basic concepts in process design, block diagrams for flow of processes, material flow
balance. Importance of codes and standards and their applications. P&ID, Process Data
Sheet, PFD and other documents used for designing. Review of Design pressures,
temperatures, design stresses, factor of safety, minimum shell thickness and corrosion
allowance, weld joints efficiency, design loading, stress concentration and thermal
stresses, failure criteria. Selection of material for process equipment’s using ASME
Codes.
06
Unit-2 Design of Pressure Vessels Types of pressure vessels, selection of various parameters for their design Pressure
vessel subjected to Internal Pressure: Complete design as per ASME code of
Cylindrical and spherical shells.
Design of various end closures such as: Flat, Hemispherical, Torrispherical, Elliptical
and conical.
Design of openings: nozzles and manholes. Design of Flanged joints; Gasket selection
and design
Design of supports for process vessels.
Pressure vessel subjected to External Pressure: Design of shell, heads, nozzles, flanged
joints and stiffening rings.
08
Unit-3 Design of Tall Vessels and Large Storage Tanks
Determination of equivalent stress under combined loadings including seismic and
wind loads application of it to vertical equipment like distillation column.
Design of Storage Tanks :
Study of various types of storage vessels and applications. Atmospheric vessels,
vessels for storing volatile and non-volatile liquids. Various types of roofs used in
storage vessels. Manholes, nozzles and mounting design. Design of Rectangular tanks.
06
Unit-4 Vessel Supports Introduction and classification of supports. Design of skirt support considering stresses
due to dead weight, wind load, seismic load and periodic vibration. Design of base
plate, skirt bearing plate, anchor bolts. Design of Lug and bracket support.
06
Unit-5 Unit 5 : Process Piping Design
Flow diagrams and pipe work symbols, design of layout of water, steam and
compressed air pipes work, pipe fitting, linings and flanged connections. Types of
valves used on pipe line. Fabrication of pipe lines, expansion joints and pipe supports.
06
Unit-6 Heat Exchangers Heat exchangers: Design of vessels, Design of Shell and Tube Heat Exchanger, Study
and design of various types of jackets like plain half coil, channel, limpet coil.
Agitator Study of various types of agitators and their applications. Baffling, Power requirement
of agitation. General design of agitator including blades, shaft, blade assembly.
08
TERM WORK
Following assignments comprise the laboratory practice:-
1) Design of Pressure vessels and large tanks.
2) Design of Heat exchangers used in industries.
3) Design and development of equipment useful to process industries such as sugar, cement,
chemical industries.
4) Preparing flow diagrams of processes, piping layout, etc.
5) Report based on visit to industries such as sugar, cement, chemical industries.
TEXT BOOKS
1) Process Equipment Design: By Dr. M.V. Joshi, Mc-Millan.
2) Process Equipment Design: By Browell and Young, Wiley India.
3) Chemical Equipment Design: B.C. Bhattacharya.
REFERENCE BOOKS
1) Plant Design and Economics: Max and Timasulaus Kalus – McGraw Hill.
2) Industrial Instrumentation servicing Hand Book : Cannel Grady, McGraw Hill.
3) Handbook of Instrumentation and Control: KellenHeward, McGraw Hill.
4) Chemical Engineering Handbook: Perry John, McGraw Hill.
5) Industrial Pipe Work: D.N.W. Kentish, McGraw Hill.
6) Chemical Engineering: J.M. Coulson, Richardson, Sinnott Vol. VII, Maxwell, McMillan.
7) Pressure Vessel Design Hand Book : H. Bedna.
8) Dryden’s outlines of Chemical Technology for the 2 : By Roa M. Gopala, Sitting M., East West
Press Pvt. Ltd., New Delhi.
References: 4. [1] Anderson J. D. Jr., “Computational Fluid Mechanics the Basics with applications", McGraw
Hill Education Pvt. Ltd.
5. [2] H. K. VERSTEEG and W. MALALASEKERA, “An introduction to computational fluid dynamics; the finite volume method.” Pearson Publication
6. [3] Suhas V. Patankar "Numerical heal transfer fluid flow", Taylor & Francis. 7. [4] Pradip Niyogi, S. K. Chakrabarthy, M. K. Laha, “Introduction to computational fluid
dynamics”, Pearson Publication
8. [5] Jiyuan Tu, Guan Heng Yeoh, Chaoqun Liu, “Computational Fluid Dynamics: A Practical Approach”, Butterworth - Heinemann
9. [6] T. J. CHUNG, “Computational fluid dynamics”, Cambridge University Press. 10. [7] Anil W. Date, “Introduction to computational fluid dynamics”, Cambridge University Press.
11. [8] S. Mostafa Ghiaasiaan, “Convective Heat and Mass Transfer”, Cambridge University Press
SHIVAJI UNIVERSITY, KOLHAPUR, B.E. (MECHANICAL ENGINEERING) PART-I
ELECTIVE -I 6. ADVANCED FOUNDRY PROCESSES
Teaching Scheme: Examination Scheme:
Lecturers: 3 Hrs/ Week Theory: 100 Marks
Practical: 2 Hrs/Week Term Work: 25 Marks
Pre-requisites: Machine tool and processes, Thermodynamics, Machine Design, Metallurgy.
Course Objectives:
1. To acquaint students with the basic concepts of foundry processes
2. To impart knowledge of Ferrous and Non Ferrous Metal Processing
3. To study casting design process
4. To analyze casting process
Course Outcomes: At the end of this course, student will be able to
1. Understand basic casting design procedure.
2. Understand fundamental knowledge of Ferrous and Non Ferrous Metal.
3. Design of castings for different application.
4. Understand need of castability.
Unit 1: Metal casting –overview and solidification (07)
Introduction to types of casting processes, Review of various processes, Solidification of Casting:
Concept of solidification of metals. Homogenous and heterogeneous nucleation.Growth mechanism,
Solidification of pure metals and alloys, Mechanism of columnar and dendritic growth, Coring or
Segregation, Solidification time and Chvorinov's rule, Concept of progressive and directional
solidifications.
Unit 2: Principles of Gating and Risering (07)
Principles of Gating and Risering: Purpose of the gating system. Components of the gating System and its
functions, Design of the gating System, Different types of gates, Gating ratio and its functions, Definition
and functions of the riser, Types of risers and their application. Design of the riser - its shape, Size and
location, Use of insulating material and exothermic compounds in risers.
Unit 3: Design of Casting (06)
Design of Casting: Factors to be considered in casting design. Designconsideration in pattern making,
moulding techniques and core making and assembly. Cooling stresses and hot spots in castingand
modification in casting geometry to overcome them, Casting Quality Control: Casting defects and factors
responsible for them.Different inspection and testing methods to evaluate the casting, Quality control
activities in a foundry,Salvaging methods of defective casting.
Unit 4: Melting Practices different alloys (07)
Melting Practices and Furnaces for Ferrous and Non- ferrous Alloys: Melting practices of Al- alloys, Mg
- alloys, Cu - based alloys and Zn- based alloys and SG Iron; Degassing process and methods in Al –
alloys, modification treatment in Al- alloys, use of covering fluxes to avoid oxidation; Desulphurization,
spherodisation treatment, inoculation practice, de-oxidation and alloy additions; Principle of working of
thermocouples, spectrometers, and C.E. meters – applications; use of pyrometers for temperature
measurement and control, energy saving in melting practices, Vacuum casting, Rheo casting.
Unit 5: Foundry Mechanization and Modernization (06)
Foundry Mechanization and Modernization: Introduction to modernization. Mechanization of foundry
and its advantages.Mechanization of sand plant, moulding and core making mechanization in melting,
pouring and shakeout units.Material handling equipments and conveyor systems. Brief sketches and
description of layouts of job. Captive and mechanized foundries.
Unit 6: Quality Control in Foundries (07)
Quality Control in Foundries: Quality specifications in respect of raw materials used in foundry sand,
sand additives, furnace charging material, alloys; Q.C. checklists maintained for raw materials, Q.C.
checklists for mould – core properties; Heat wise pouring reports, details of melting log sheets, test bars,
calibration records of testing equipments (U.T.M., Sand testing equipments); Results of chemical
analysis, mechanical properties, test reports, rejection report analysis, defect diagnosis, remedies, use of
cause - effect or fish- bone diagrams, Application of S.Q.C. in foundries, control charts
TERMWORK 1. Sand moulding laboratory report preparation 2. Design of pattern layout for a given component 3. Design of gating system for a given component (ferrous / non ferrous) 4. Design of risering system for a given component (ferrous / non ferrous) 5. Die design for pressure die casting / centrifugal casting 6. Design of a foundry layout for a given case 7. Study of any one type of melting furnace 8. Study of TS/ISO / QS norms for foundry industry 9. Industrial visit to a modern foundry and its report
(Use of computer in designs is essential)
TEXTBOOKS :
1) Metal casting: computer aided design and analysis, B .Ravi, prentice hall india.
2) Principles of Metal Castings - Heine, Loper and Rosenthal (TMH)
3) Principles of Foundry Technology - P.L. Jain (TMH)
4) Foundry Technology - Beelely, P.R. – Butterworth.
5) Text Book of FoundryTechnology - Lal, M. Khanna, P.O – Dhanpat Rai & Sons
6) Manufacturing Processes and Systems, Phillip F Ostwald, J. Munoz, Wiley Student Edi. ISBN
89-81-26518944
REFERENCE BOOKS
1. Indian Institution of Foundrymen - Foundry Journal 2. Advanced Pattern Making – Cox I.I. (The Technical Press, London.) 3. ASM Handbook – Vol. 15 Castings. (McGraw Hill) 4. Metal Castings – Principles & Practice - T.V. RamanaRao. (New Age Publishers.) 5. AFS and Control hand book – AFS. 6. Mechanization of Foundry Shops – Machine Construction - P.N. Aeksenov (MIR) 7. Fundamentals of Metal Casting Technology - P.C. Mukherjee (Oxford, IBH) 8. Foundry Engineering – Taylor, Fleming & Wulff (John Wiley) 9. The Foseco Foundryman's Handbook – Foseco, CBS Publishers & Distributors 10. The New Metallurgy of Cast Metals Castings – Campbell, CBS Publishers & Distributors,
Shivaji University Kolhapur
B.E. (MECHANICAL ENGINEERING) PART-I
ELECTIVE -I INTRODUCTION TO AIRCRAFT SYSTEMS
Teaching Scheme: Examination Scheme:
Lecturers: 3 Hrs/ Week Theory: 100 Marks
Practical’s: 2 Hrs/ Week Term work: 25 Marks
Course Objectives
1. Get introduced to the Aircraft History, Industry 2. Able to analyze effect of Wind over Aerofoil, Aircraft 3. Able to analyze. Assess & Judge stability of Aircraft. 4. Understand the Basics of Aircraft Systems and Systems Engineering approach. 5. Industry Practices on Design of Aircraft Systems: Mechanical, Electrical. 6. Understand the applicability of Design aspects in Aircraft Design. 7. Relate the theoretical knowledge with the design of Aircraft Structures.
Course outcomes
This course intends to help student develop the capability of systems thinking by introducing basic &
intermediate systems engineering theory, methods, and tools. After taking this class, Student should be
able to:
1. Develop a systems engineering plan for a realistic project. 2. Judge the applicability of any proposed process, strategy, or methodology for systems
engineering using the fundamental concepts from disciplines such as probability, economics,
and cognitive science.
3. Understand system engineers' role and responsibilities. Understand the role of organizations. 4. Apply systems engineering tools (e.g., requirements development and management, robust
design, Design Structure Matrix) to realistic problems.
5. Recognize the value and limitations of modeling and simulation. 6. Formulate an effective plan for gathering and using data. 7. Know how to proactively design for and manage system lifecycle targets.
SYLLABUS
UNIT I: Introduction to Aircraft & Principles of Flight [06]
Evolution and History of Flight, Aircraft definition, Aircraft classification, Basic components of an
Aircraft, Aircraft control surfaces-movements, Aircraft axis systems, Types of Aircraft’s – Lighter than
air/ Heavier than air Aircraft.
Principles of Flight: Forces on Aircraft, Properties of atmosphere, Bernoulli’s Principle & equation,
Airflow over wing, Pressure distribution over wing section, Types of Drag, Basics of Lift & Drag.
UNIT II: Aircraft Stability & Control [08]
Lateral, Longitudinal, Directional stability & controls of aircraft, Factors affecting lateral, longitudinal &
directional stability. Why different Aircraft’s have different designs-Conventional Aircraft, Un-
Conventional Aircraft
UNIT III: Aircraft Systems [10]
(A) Mechanical Mechanical Systems: Environmental control systems (ECS), Pneumatic systems, Hydraulic systems, Fuel
systems, Landing gear systems, Engine Control Systems, Ice and rain protection systems, Cabin
Pressurization and Air Conditioning Systems, Steering and Brakes Systems, Auxiliary Power Unit.
(B) Electrical & Electronics Electrical systems: Avionics, Flight control Systems, Autopilot and Flight Management Systems,
Navigation Systems, Communication, Information systems, Radar System, Emergency Systems.
UNIT IV: Systems Engineering [06]
Introduction to Systems Engineering- An approach, Need for Systems Engineering, Scope of Systems
Engineering activities, Systems Engineering-Process, tools used for Systems Engineering process,
Systems Integration, Systems Interaction. Role and Responsibilities of a Systems Engineer, Understand
the role of organizations
UNIT V: Aircraft Systems Design [05]
Introduction to Aircraft Systems design, Development Process, Key Elements of Design process, System
Requirements, Fault Tree Analysis (FTA), Dependency Diagram, Failure Modes and Effects Analysis
(FMEA), Reliability- Analytical methods Development verification and validation, reliability, system
attributes
UNIT VI: Aircraft Systems Development Process [05]
Introduction to Development Process, Product Life Cycle (PLC), Concept Phase, Definition Phase,
Design Phase, Build Phase, Test Phase, Operate Phase, Disposal Phase, Development Program, Design &
Development verification and validation, reliability, System attributes.
Term work:
1. Eight assignments based on above topics. 2. Two reports on Industrial Exposure or visit.
Practical Exposure
With an intent to get some exposure on Aerospace and related industries, the colleges can arrange
Industry Visits to some of the Industries in Aerospace like HAL(Hindustan Aeronautics Limited),NAL (National Aerospace Limited),ISRO (Indian Space Research Organization) and
Students need to submit a report on the learning from the visits (OR)
Visits to Aerospace Museums (OR)
Building miniature Models of Aircraft /Gliders etc as Hands on Exercises conducted as competitions.
Courseware & Reference Books:
The courseware including PowerPoint and notes are available for the Elective. In addition,
following reference books can also be used.
1. Aircraft Systems: Mechanical, electrical, and avionics subsystems integration – 3rd Edition by Ian Moir, Allan Seabridge
2. Flight without Formulae by A.C Kermode, Pearson Education,10th Edition 3. Mechanics of Flight by A.C Kermode, Pearson Education,5th Edition 4. Fundamentals Of Flight, Shevell, Pearson Education, 2nd Edition 5. Introduction to Flight by Dave Anderson 6. Aircraft Maintenance & Repair by Frank Delp, Michael J. Kroes & William A. Watkins, Glencoe
&McGraw-Hill, 6th Edition, 1993.
SHIVAJI UNIVERSITY, KOLHAPUR, B.E. (MECHANICAL ENGINEERING) PART-I
ELECTIVE -II 1. TOTAL QUALITY MANAGEMENT
Teaching Scheme: Examination Scheme:
Lecturers: 3 Hrs/ Week Theory: 100 Marks
Practical: 2 Hrs/Week Term Work: 25 Marks
Pre-requisites: Metrology and Quality Control, Industrial Management and Operation Research
Course Objectives: 1. To know the concept of Total Quality and role of Quality assurance. 2. To understand Planning and Controlling techniques for quality 3. To know the reliability approach for Quality 4. To realize Benefits of Taguchi’s Quality philosophy 5. To understand the key issues and some popular approaches to TQM implementation 6. To understand the current trends in TQM
Course Outcomes:
1. Students can understand importance of assuring quality in the service or manufacturing sector and explain Quality assurance system
2. Student can identify and solve the quality related problems in manufacturing or service sector at various stages by using various TQM tools and techniques,
3. Students are able to calculate reliability of system 4. Students are able to understand vendor rating and select suitable vendor 5. Students are able to interpret various quality attributes and discuss the various quality
approaches.
6. Students are able to comment on quality using Taguchi philosophy.
Unit 1: Quality assurance System: (06)
Concept of total quality, role and objectives of Q.A. Q.A. cycle, process approach to Q.A. (input-
process-output), information feedback, significance of feedback and field complaints analysis in
Q.A., significance of internal customer approach, defect prevention programs for Q.A.
Unit 2: Planning and controlling techniques for quality (07)
Planning for quality – The dimensions of Quality ( quality of Design, conformance,
performance and service )Specifications for quality dimensions, quality planning activities for
new products, Advanced Product Quality Planning(APQP),planning through trial lots, quality
planning with vendors, vendor control procedures, vendor-rating.
Controlling techniques for quality –seven statistical tools, process capability analysis, problem
solving new management tools, six sigma- concept, need, implementation, DPMO, gradations.
Unit 3: Robust and reliable product approach for Quality (07)
Product and system reliability: Basic concepts, prediction and evaluation of parallel, series and
combined system reliability reliability tests (life testing, burn-in test, accelerated life testing),
FMEA; and FTA, Taguchi’s quality philosophy, system design, parameter design, tolerance
design, orthogonal arrays, S/N ration, loss functions.
Unit 4: Principles and Approaches to TQM: (06)
Basic concepts: definition of TQM, TQM and traditional management approach, principles,
characteristics, and benefits of TQM.
Approaches to TQM: Deming’s approach, Juran’s triology, Crosby and quality improvement,
Ishikawa’s CWQC, Feignbaum’s theory of TQC, Schonberger’s action agenda for manufacturing
excellence.
Unit 5: The essentials of TQM: (07)
Customer focus,- customer perception of quality, quality policy deployment, quality function
deployment, voice of customer ,customer satisfaction, Kano’s model of satisfaction, customer
retention,.
TQM leadership,- role and commitment and accountability of leadership, quality policy and
objectives, Organizational structure for TQM, role of HR in TQM, training for TQM, developing
quality culture.
Tools and techniques for TQM: 5-S campaign, TEI, quality circles, QFD, poka-yoke, KAIZEN
Unit 6: Current trends in TQM: (07)
TQM in service sector: Definition and meaning and service, problems in defining service
quality, attributes of service quality, SERVQUAL model, Implementing TQM in service
industries, measurement system for service quality.
Quality Management Systems:
ISO 9001:2008 Series Standards – Clauses, contents, interpretation and implementation, audit
Sector Specific Standards – AS 9100, ISO/ TS 16949, TL9000,
Quality Awards: national and international quality awards, criteria and case studies.
TERM WORK
Five assignments based on the syllabus
Four case studies through industrial visits on 1. Tools and techniques of TQM 2. TQM implementation in manufacturing sector 3. TQM implementation in Service Sector 4. ISO 9001-2008 implantation
(Presentation is preferable for case studies)
TEXT BOOKS:
1. Patrick D.T. O’connor, “Practical Reliability Engineering”, Wiley India, IV Ed. (ISBN 978-
81-265-1642-1)
2. Total Quality Management – Text and cases by Jankiraman and Gopal, PHI Publication.
(ISBN 978-81-203-2995-9)
3. Total Quality Management – by Dr. Suri and Dr. Sharma, Wiley Publication. (ISBN 978-93-
5004-317-2)
4. Total Quality Management – by Dr. Rajaram, Wiley Publication. (ISBN 978-81-7722-63-2)
REFERENCE BOOKS:
1. Dale H. Besterfiled,et.al. “Total Quality Management”, Pearson Education Asia (ISBN 978-
81-317-3227-4)
2. Dr. Poornima Charantimath “Total Quality Management”, Pearson Education Asia, Second
edition ( ISBN 978-81-317-3262-5)
3. Amitava Mitra, “ Fundamentals of Quality Control and Improvement”, PearsonEducation
Asia
4. Dr. R.P.Mohanti ,R.R. Lakhe “ Handbook of Total Quality Management”, Jaico Publishing
House , ( ISBN 81-7224-833-44)
5. Dr. R.P. Mohanti “Total Quality Management in Service Sector”, Jaico Publishing House
6. Juran J.M & Gryna Quality Planning and analysis
7. Sharma S.C., “Inspection, Quality Control and Reliability”, Khanna Publishers (ISBN 81-
7409-022-3)
8. Dinesh Seth, Subhash C. Rastogi “ Global Management Solutions Demystified” Ceneage
Education ( former ThomsonAsia Pvt.Ltd.) ( ISBN 981-265-142-X)
9. Total Quality Control -Feigenban - McGraw Hill Book Company, New York
10. Barrie G Dale et al, “Managing Quality”, Wiley India P.Ltd. Vth Edi. (ISBN 978-81-265-
2246-0)
SHIVAJI UNIVERSITY, KOLHAPUR,
B.E. (MECHANICAL ENGINEERING) Semester –VII
INDUSTRIAL PRODUCT DESIGN (Elective –II)
Lecture: 3 Hrs/week Theory: 100 Marks
Practical: 2 Hrs/week Term Work: 25 Marks
Course Objectives:
1. To study the various parameters in product design and development like
Finding Customer Needs
Doing Market Research in various parameters for product
Product Specifications criteria
Product Architecture and Prototyping
Cost and Value Engineering
Design for Manufacturing and Assembly
Standards in Ergonomics and Industrial Safety
2. To practice exposure to Case Studies and CAD Software with a product case.
Course Outcomes:
After completion of the course, the student will be able to
1. Find the Customer Needs for a Quality Product through Market Research in product development
process, Concept Generation, Selection and Testing.
2. Describe basics of Product Architecture, Prototyping and Cost & Value Engineering.
Select the Standard Ergonomics and Industry Safety parameters in Product Design.
SECTION – I
Unit 1 Introduction
Challenges of product development, Identify customer needs, Successful product
development, Quality aspect of product design, Market Research, Survey.
(06)
Unit 2 Product Development Process and Planning
Innovation and Creativity in Product Design, Product Planning Processes, Product
specifications: Process of setting specifications. (Concept Generation–Selection–
Testing).
(07)
Unit 3 Product Architecture
Product Architecture: Implication of architecture, establishing the architecture,
Related system level design issue, Product Data Management, Use of Computerized
Data Management and `Process, Industrial Design : Overview.
(07)
SECTION – II
Unit 4 Design for Manufacturing and Assembly
Tolerance, Design of Gauges, Design for Environment, Prototyping, Engineering
Materials, Concurrent Engineering, Product Costing, Value engineering.
(07)
Unit 5 Aesthetics :
Aesthetic Considerations, Visual Effects of Form and Color in Product Design.
Ergonomics :
Ergonomics and product design and automated systems, Anthropomorphic Data and
its applications in ergonomic design, Limitations of Anthropomorphic Data, General
approach to the Man-Machine Relationship - Workstation Design and environment
(working position and posture).
Control and Displays:
Configurations and sizes of various controls and displays- design of controls in
automobiles, machine tools etc., design of instruments and controls.
(08)
Unit 6 Industrial Safety:
An approach to Industrial Design - Elements of Design Structure for Industrial Design
in engineering applications in manufacturing systems.
Personal protective Equipment and Environment Control Prevention and specific
safety measures for manufacturing and processing industry and chemical industry.
(05)
Term Work:
1. Case Study on any TWO(by a group, a group of Min.02 and Max. 04 students to be presented in front of all students) covering following points,
a. Product Development Process / Planning. b. Product Architecture. c. Design for Manufacturing . d. Design for Assembly. e. Aesthetic and Ergonomic considerations in Product Design. f. Industrial Safety in Machine & Equipment handling. g. Health Safety in Product Design. h. Environmental Safety and ISO 14000 Systems.
2. Development of any Product using high end CAD software considering following points.
a) Need of Customer, Methodology of Market Survey. b) Invention / Innovation of a product with modifications required. c) Aesthetics (Form & Color) and Ergonomics consideration in design. d) Preparation of various Views of the product. e) Design for Assembly Procedures . f) Product and Maintenance Manual. g) Product Database Management .
A report should be prepared with details, drawing sheet, Bill of Material, Assembly –
Disassembly Procedure, Maintenance Manual and Cost Estimation (if required)
3. Presentation of the product designed.
TEXT BOOKS :
1. “Product Design and Development”, Karl T. Ulrich, Steven G. Eppinger; Irwin McGraw Hill. 2. “Product Design and Manufacturing, A.C. Chitale and R.C. Gupta, PHI. 3. “Product Design”,Otto and Wood, Pearson education. 4. “Human Factor Engineering”, L P Singh , Galgotias.. .
REFERENCE BOOKS:
1. “New Product Development”, Tim Jones, Butterworth, Heinemann, Oxford, 1997. 2. “Assembly Automation and Product Design, Geoffrey Boothroyd, Marcel Dekker. 3. “Industrial Product Design”, C W Flureshem. 4. “Industrial Design for Engineers” Mayall W.H, London, Hiffee books Ltd. 5. “Introduction to Ergonomics”, R.C. Bridger, McGraw Hill Pub.
SHIVAJI UNIVERSITY, KOLHAPUR, B.E. (MECHANICAL ENGINEERING) Semester VII
3. ADVANCED FORMING PROCESSES (ELECTIVE-II)
Teaching Scheme: Examination Scheme:
Lecturers: 3 Hrs/ Week Theory: 100 Marks
Practical: 2 Hrs/Week Term Work: 25 Marks
Pre-Requisites: Machine Tool & Processes, Metallurgy, Thermodynamics.
Course objectives
1. To understand the fundamentals of various traditional, nontraditional and advanced metal forming processes
2. To study different types of traditional, nontraditional and advanced metal working processes, their advantages, limitations and applications
3. To understand the understanding of how the processes are carried out in industry
Course Outcomes
At the end of the course the student will be able to
1. Solve for strain rates, temperatures and metallurgical states in forming problems using constitutive relations
2. Develop process maps for metal forming processes using plasticity principles 3. Estimate formability limits for bulk metals and sheets 4. Evaluate high energy rate deformation process parameters.
Unit I: Introduction and Fundamentals of Forming Processes: (05)
Importance of manufacturing technology, classification of manufacturing processes, selection of materials
and manufacturing processes. Study of various forming processes their significance and comparison of
various manufacturing processes on different criteria. Need for near net shape manufacturing.
Theory of elasticity, Simple Stress and Strains- Elastic stresses and strains, Plastic stresses and strains,
Poisson’s ratio, True stress and True strain, Empirical relations for the stress strain curve, Idealized stress
strain curve. Two and three dimensional stresses and strains- Principal stresses and strains, Mean
(Hydrostatic) stress and stress deviators, Principal strains, Equilibrium in Cartesian, cylindrical and
spherical coordinates
Unit II: Theory of Plasticity (07)
Theory of dislocations, Slip line field theory, slab method and lower and upper bond methods for load ,
their significance in investigating and modeling of metal working operations. Plastic work.Yield criteria-
Tresca and Von mises yield criteria, General plastic stress-strain relations (Theory of plasticity).
Effect of Temperature on plastic deformation, cold forming- and effect of annealing on cold formed
materials- recovery, recrystallization and grain growth, warm forming and hot forming. Effect of strain
rate on plastic deformation and super plasticity.Effect of friction and lubrication in metal forming.
Classification of forming processes on various criteria
Unit III: Bulk Forming of Metallic Materials (08) Forging Processes: Introduction to types of forging and forging equipments, Modeling of forging
process, Calculation of forging loads in closed die forging, Effect of forging variables on properties,
forging die design, design principles, pre form design considerations and die materials, Forging Defects.
Rolling Process: Introduction to types of rolling and rolling mills, Forces and geometrical relationships in
rolling, simplified analyses of rolling load , variables, torque and power, roll pass design, Rolling mill
control, theories of cold rolling, hot rolling, transverse rolling, rolling of bars and shapes. Rolling defects
Extrusion: Classification and applications, Extrusion equipment. Hot and cold extrusion, hydrostatic
extrusion. Patterns of metal deformation in extrusion, Analyses of extrusion process, Extrusion Defects.,
Rod, Wire and Tube Drawing: Classification of drawing processes. Rod Drawing, Wire Drawing, Tube
Drawing. The Drawing Die. Modeling of Drawing Process.
Unit IV: Sheet Metal Forming Processes: Introduction and Classification (07)
Shearing Processes: Classification and applications, Open Contour Shearing, Closed Contour Shearing.
Shearing mechanism.
Bending Processes: Applications, Bending Parameters, spring back in Bending, Residual stresses in
bending. Bending equipment, Press Brake, Roll Bending Machines and Contour Roll forming.
Stretch Forming: Applications, Stretch forming machines and accessories.
Deep Drawing: Applications. Deformation zones in deep drawing, Blank holding pressure. Ironing. Deep
Drawing force. Limiting Drawing Ratio. Effect of Anisotropy. Redrawing.
Unit V: High Velocity Forming and High Energy Rate Forming (06)
Introduction and Classification. Characteristics of HVF and HERF Processes.
High Velocity Forming Machines: Pneumatic (Compressed air) Hammer, Compressed Gas Forming
Hammer, Gas Combustion High Speed Hammers,
High Energy Rate Forming Processes: Explosive Forming, Principles and Types of Explosives.
Classification of Explosive Forming Methods, Process variables, Failure of Formed products , advantages
and limitations,
Electro Magnetic Forming: Principles of the process, Basic Methods of Electromagnetic Forming,
Pressure required in EMF, Advantages and Limitations of EMF. Safety Considerations.
Electro Hydraulic Forming: Principles of the Process, Energy requirements, Process variables,
Advantages and Limitations, Future of HVF and HERF.
Unit VI: Recent trends in Forming: (07)
Thixo- forging, isothermal forging, super plastic forming technology, forming of super conductors,
forming of ceramics and glasses, Forming of plastics and composite materials- Extrusion, Form
moulding, Thermo forming, Cold forming and Solid phase forming, design and economic considerations.
Rubber Pad Forming (Flexible – Die Forming) and Hydro forming (Fluid forming Processes).
Spinning: Conventional spinning, Flow Turning (Shear spinning), Tube spinning,
Super plastic Forming of Sheets: Blow Forming and Vacuum Forming, Thermo forming Methods,
Super Plastic Forming/ Diffusion Bonding Process. Sheet Metal Formability, Testing of Formability,
Forming Limit Diagrams.
TERM WORK:
1. One exercises each on i. Rolling ii. Forging iii. Extrusion, iv. Wire and deep drawing forming processes
2. Four exercises on High velocity and high energy rate forming 3. Industrial visits to observe bulk metal, sheet metal and High velocity and high energy rate forming
processes
TEXT BOOKS:
1. Mikell Groover, “Modern Manufacturing”, Wiley publication 2. George E. Dieter, “Mechanical Metallurgy”, McGrew Hill Edu. (India) Pvt. Ltd. 3rd Edition 2013 , (
ISBN 978-1-25-906479-1)
3. Helmi A. Youssef, Hassan A. El- Hofy, Mahmoud H. Ahmad, “Manufacturing Technology – Materials, Processes and Equipments”, CRC Press, Taylor and Francis Group, ISBN 978-1-4398-
1085-9
4. R.K. Jain, “Production Technology”, Khanna Publishers (ISBN :81-7409-099-1)
5. Phillip F Ostwald, J. Munoz, “Manufacturing Processes & Systems”, Wiley Student Edi. ISBN 978-81-26518944.
REFERENCE BOOKS
1. Metal forming Handbook- Schuler, Springer-Verlag Berlin Heidelberg New York (2008) ISBN 3- 540-61185-1
2. Forging Design and Practice- R. Sharan, S.N. Prasad 3. Forging Equipment, material and processes, J. Altan, F. W. Boulger- Metals Cewramic Information
centre Columbus 1973
4. Roll Forming Handbook- Geotge T. Halmos (CRC Press, Taylor and Francis)- 2006 ISBN 0- 8247-9563-6
5. Metal Forming Fundamentals and Applications- Altan T, American Society of Metals, Metal Park 1983
6. ASM Hand Book- Forming and Forging, 9/e. Vol. 14 (1998) 7. Serope Kalpakjain, Steven R. Schmid “Manufacturing Engineering and Technology” Pearson
Education Asia 4th Edition ( ISBN 978-81-7758-170-6)
8. B.L. Juneja “Fundamentals of metal forming processes”, New Age International Publishers Second edition ( ISBN 978-81-224-3089-9)
9. Geotge T. Halmos” Roll Forming Handbook” CRC Press, Taylor & Francis (2006) (ISBN :0-8247-
9563-6)
SHIVAJI UNIVERSITY, KOLHAPUR,
B.E. (Mechanical Engineering) Semester -VII
Design of Thermal Systems (Elective-II)
Teaching Scheme: Examination Scheme:
Theory: - 3 hrs/ week Theory: - 1 00 Marks
Practical: - 2 hrs/week Term Work: - 25 Marks
Course objectives:
1. Students shall learn thermal system design methodology 2. Students shall understand real life situations and be able to decide an approach for problem solving. 3. Students shall be able to design simple thermal systems with advanced tools where in integration of
more than one component is required.
Course Outcomes:
1. Students will understand the thermal system design methodology 2. Students will be able to decide an approach to solve real life thermal system design problems. 3. Students will be able to design simple thermal systems with advanced computer aided systems 4. Students will gain confidence in problem solving.
Unit 1: Introduction to thermal system design (6)
Classification of design, Optimal and nearly optimal design, Methodology of design, Aspects of thermal
system design, Assessment concept and creation, Component modeling
Unit 2: Design of Refrigeration system (7) Design of basic components of refrigeration system, Design of refrigeration systems: vapour compression
system- Household refrigerator, Ice plant, vapour absorption systems using waste heat and solar energy.
Unit 3: Heat Transfer and Design Analysis of Air Conditioning System (7)
Design of Air conditioning systems: Design considerations, Load calculations, Single unit room air
conditioners, Central air conditioning plant, Industrial drying systems, component selection and Computer
Aided Piping Design.
Unit 4: Design of Solar System (7)
Design of solar assisted water heating systems, preliminary specifications, concepts development, detailed
design for feasibility study, component design
Unit 5: Design of Advanced Cooling Systems (6)
Design of advanced heat exchanger networks, Design of electronic miniature cooling systems, Utilization of
Nano- Fluids for Cooling Systems
Unit 6: Design and Economic Analysis of Waste Heat Recovery Systems (7)
Design of waste heat recovery systems, Design specifications, Concept development, Detailed specifications
and component design, Thermo Economic Evaluation and additional costing considerations
Term Work: Any six assignments to be completed 1. Design of water chilling plant 2. Design of cold storage plant 3. Design and optimization of fins 4. Design of waste heat recovery system for diesel power plant 5. Design of dehumidification plant used for industrial drying.
6. Design of gas turbine system 7. Design of shell and tube heat exchangers
*(Designing of any one basic component with CAE software like ANSYS, HYPERWORKS)
Reference Books:
1. HVAC System design Handbook- ASHRAE 2. Design and optimization of thermal systems – Yogesh Jalurkar, CRC Press 3. Design and simulation of thermal systems- N.V. Suryanarayana, Oner Arici, Mc Graw Hill Inc. 4. Thermal system Design - Stoecker 5. Essentials of thermal system Design- C. Balaji, CRC Press 6. Design of fluid thermal systems- Janna W.S., Cengage L