SFH 2504

1 Version 1.4 | 2018-05-04

Produktdatenblatt | Version 1.1 www.osram-os.com

SFH 2504

Radial T1 3/4 Silicon PIN Photodiode with integrated Temperature Sensor

Applications — Electronic Equipment

Features: — Package: black epoxy

— ESD: 2 kV acc. to ANSI/ESDA/JEDEC JS-001 (HBM, Class 2)

— Especially suitable for applications from 740 nm to 1100 nm — 5 mm LED plastic package — Integrated NTC thermistor, R25=10kΩ

Ordering Information

Type Photocurrent Photocurrent Ordering Codetyp.

Ee = 1 mW/cm²; λ = 870 nm; VR = 5 VEe = 1 mW/cm²; λ = 870 nm; VR = 5 VIP IP

SFH 2504 AN23 ≥ 1.9 µA 2.7 µA Q65110A3986

SFH 2504

2 Version 1.4 | 2018-05-04

Maximum RatingsTA = 25 °C

Parameter Symbol Values

Operating Temperature Top min. max.

-40 °C 100 °C

Storage temperature Tstg min. max.

-40 °C 100 °C

Reverse voltage VR max. 30 V

Total power dissipation Ptot max. 30 mW

ESD withstand voltage acc. to ANSI/ESDA/JEDEC JS-001 (HBM, Class 2)

VESD 2 kV

SFH 2504

3 Version 1.4 | 2018-05-04

CharacteristicsTA = 25 °C

Parameter Symbol Values

Wavelength of max sensitivity λS max typ. 870 nm

Spectral range of sensitivity λ10% typ. 740 ... 1100 nm

Radiant sensitive area A typ. 0.31 mm²

Dimensions of active chip area L x W typ. 0.56 x 0.56 mm x mm

Half angle φ typ. 60 °

Dark current VR = 10 V

IR typ. max.

0.05 nA 5 nA

Rise time VR = 10 V; RL = 50 Ω; λ = 850 nm

tr typ. 0.01 µs

Fall time VR = 10 V; RL = 50 Ω; λ = 850 nm

tf typ. 0.01 µs

Forward voltage IF = 100 mA; E = 0

VF typ. 1.2 V

Capacitance VR = 0 V; f = 1 MHz; E = 0

C0 max. 13 pF

Temperature coefficient of voltage TCV typ. -2.6 mV / K

Resistance Thermistor (EPCOS B57860S0103A002)

R25 typ. 10 kΩ

Tolerance of resistance Thermistor (EPCOS B57860S0103A002)

Rtol typ. 3 %

Rated temperature Thermistor (EPCOS B57860S0103A002)

Tn typ. 25 °C

SFH 2504

4 Version 1.4 | 2018-05-04

4000

nm

%

OHF05547

20

40

60

80

100

λ

relS

10

30

50

70

500 600 700 800 900 1100

Relative Spectral Sensitivity 1), 2) Srel = f (λ)

-900

deg

%

OHF05551

20

40

60

80

100

ϕ

relS

10

30

50

70

-60 -30 0 30 90

Directional Characteristics 1), 2) Srel = f(φ) perpendicular to leads

SFH 2504

5 Version 1.4 | 2018-05-04

-900

%

OHF05552

20

40

60

80

100

ϕ

relS

10

30

50

70

-60 -30 0 30 deg 90

Directional Characteristics 1), 2) Srel = f(φ) parallel to leads

V

OHF01026

R

RΙ

0

410

310

210

10 1

pA

20 V 3010

Dark Current 1), 2)

IR = f (VR) ; E = 0

I

OHF05550

P

Ee

µA

mW/cm10-2

210-2

10-1

100

110

210

10-1 110

Photocurrent/Open-Circuit Voltage 1), 2)

IP = f(Ee), λ = 870 nm, VR = 5 V

SFH 2504

6 Version 1.4 | 2018-05-04

Capacitance 1), 2)

C = f (VR); f = 1 MHz; E = 0;

-500.6

˚C

OHF05553

P relI

-25 0 25 50 100

AT

0.7

0.8

0.9

1.0

1.1

1.2

PhotocurrentIP/IP(25°C) = f(TA), λ = 870 nm, VCE = 5 V

-25

I

OHF05549

R

TA

nA

˚C0 25 50 75 10010-3

10-1

100

10-2

110

210

Dark Current 2)

IR = f (TA); E = 0; VR = 10 V

SFH 2504

7 Version 1.4 | 2018-05-04

00

P

OHF05548

tot

TA

mW

˚C

10

20

30

40

50

25 50 75 100 125

Power ConsumptionPtot = f (TA);

SFH 2504

8 Version 1.4 | 2018-05-04

Dimensional Drawing 3)

Approximate Weight: 337.0 mg

SFH 2504

9 Version 1.4 | 2018-05-04

Recommended Solder Pad 3)

SFH 2504

10 Version 1.4 | 2018-05-04

TTW SolderingIEC-61760-1 TTW

00

s

OHA04645

50

100

150

200

250

300

t

T

˚C

235 ˚C - 260 ˚CFirst wave

20 40 60 80 100 120 140 160 180 200 220 240

Second wave

10 s max., max. contact time 5 s per wave

Preheating

T∆

100 ˚C120 ˚C130 ˚C

Typical

Cooling

ca. 3.5 K/s typical

ca. 2 K/s

ca. 5 K/s

Continuous line: typical processDotted line: process limits

< 150 K

SFH 2504

11 Version 1.4 | 2018-05-04

NotesThe evaluation of eye safety occurs according to the standard IEC 62471:2006 (photo biological safety of lamps and lamp systems). Within the risk grouping system of this IEC standard, the LED specified in this data sheet fall into the class exempt group (exposure time 10000 s). Under real circumstances (for expo-sure time, conditions of the eye pupils, observation distance), it is assumed that no endangerment to the eye exists from these devices. As a matter of principle, however, it should be mentioned that intense light sources have a high secondary exposure potential due to their blinding effect. When looking at bright light sources (e.g. headlights), temporary reduction in visual acuity and afterimages can occur, leading to irrita-tion, annoyance, visual impairment, and even accidents, depending on the situation.

Packing information is available on the internet (online product catalog).

For further application related informations please visit www.osram-os.com/appnotes

SFH 2504

12 Version 1.4 | 2018-05-04

Disclaimer

DisclaimerLanguage english will prevail in case of any discrepancies or deviations between the two language word-ings.

Attention please!The information describes the type of component and shall not be considered as assured characteristics. Terms of delivery and rights to change design reserved. Due to technical requirements components may contain dangerous substances.For information on the types in question please contact our Sales Organization.If printed or downloaded, please find the latest version in the OSRAM OS Webside.

PackingPlease use the recycling operators known to you. We can also help you – get in touch with your nearest sales office.By agreement we will take packing material back, if it is sorted. You must bear the costs of transport. For packing material that is returned to us unsorted or which we are not obliged to accept, we shall have to invoice you for any costs incurred.

Product safety devices/applications or medical devices/applicationsOSRAM OS components are not developed, constructed or tested for the application as safety relevant component or for the application in medical devices.In case Buyer – or Customer supplied by Buyer– considers using OSRAM OS components in product safety devices/applications or medical devices/applications, Buyer and/or Customer has to inform the local sales partner of OSRAM OS immediately and OSRAM OS and Buyer and /or Customer will analyze and coordi-nate the customer-specific request between OSRAM OS and Buyer and/or Customer.

SFH 2504

13 Version 1.4 | 2018-05-04

Glossary1) Testing temperature: TA = 25°C2) Typical Values: Due to the special conditions of the manufacturing processes of LED, the typical data

or calculated correlations of technical parameters can only reflect statistical figures. These do not nec-essarily correspond to the actual parameters of each single product, which could differ from the typical data and calculated correlations or the typical characteristic line. If requested, e.g. because of technical improvements, these typ. data will be changed without any further notice.

3) Tolerance of Measure: Unless otherwise noted in drawing, tolerances are specified with ±0.1 and dimensions are specified in mm.

SFH 2504

14 Version 1.4 | 2018-05-04

Published by OSRAM Opto Semiconductors GmbH Leibnizstraße 4, D-93055 Regensburg www.osram-os.com © All Rights Reserved.