18" Babbington Aluminium Staging. INSTRUCTIONS. Slightly shorter than 4’, 6’, 8’,10’. Please read ALL before you begin.

Parts list: 4ft Model: (Picture 1) 4 x 2ft trays. 8 x legs. 1 bag of nuts and bolts. 6ft Model: 6 x 2ft trays. 12 x legs. 1 bag of nuts and bolts. 8ft Model: 8 x 2ft trays. 16 x legs. 1 bag of nuts and bolts. 10ft Model: 10 x 2ft trays. 20 x legs. 1 bag of nuts and bolts.

8ft example. Picture 1

Required tools: 10mm Spanner (1) Large flat screwdriver (2) Optional tools: Pozi screwdriver (3) 10mm spinner (4)

4 3

2 1 PIC 2

PIC 4

PIC 3

Making your first 2ft section: You will require 4 legs, 2 trays, and your bag of nuts

and bolts. Using your nuts and bolts with your spanner and flat

screwdriver join the legs and trays together (PICS 3, 4) to make a 2’ section as shown in picture 6.

Picture 6

PTO

Picture 7

Picture 8

Join 2ft sections as in PIC 10.

Leave short end holes free on

one side.

Short face.

Long face.

Important Note: On one of the short faces leave the holes free of nuts and bolts (Pictures 7, 8, 9, 10) ready for your next 2ft section to be attached.

Erectors Tip

Important Note: Measure the entrance to your greenhouse and compare it to the tray width / depth. If your doorway is narrow it may be a good idea to build your staging inside the greenhouse to make life easier later on.

Erectors Tip

PIC 10

PIC 5

PIC 9

Setting Up: Firstly make sure you have a flat, clean area in which to work or the staging will not be level when lifted into position.

Collate all of your components along with the required tools. Note: The nuts and bolts can be inserted in either direction (PIC 2, 5). Having the nuts on the inside (PIC 10) is the neater option but will take more time.

Joining 2ft sections together: (Pics 7—11) For every 2ft section you will need to repeat the

previous set of instructions. However in the 6ft, 8ft and 10ft options you can leave the centre 2ft sections (Picture 13) in the run free of short face bolts on both short faces. This is because the holes and their subsequent nuts and bolts are required to join the short faces of each 2ft section together. (Pictures 7—14)

When you have made all your 2ft sections you

can combine them to the required length.

Centre 2ft Section on 6ft model. Picture 13.

Picture 11.

Alternative Options: The sections can also be joined through the long sides producing a shorter but deeper result (see picture above left).

When attaching sections ensure that the edges are flush to give a smooth finish.

Picture 14

Flush

Or shop on-line at the web

address below.

If you have any problems please do not hesitate to call

us on 01782 388811. www.greenhousepeople.co.uk

If you would like a brochure containing our extensive product range

then please contact us at, ‘The Greenhouse People’, Unit 19 Blythe Park, Cresswell Lane, Cresswell, Stoke—On—Trent. Staffs. ST11 9RD.

Note: If you have difficulty lining up the holes between your 2ft sections loosen the nuts around the joint in question and use a Pozi screwdriver to gently align the holes. (Pictures 12, 14)

Picture 12. Erectors Tip

Trays can be filled with gravel, soil, plant pots etc.. Please note that as a natural part of the CNC laser cutting the gravel trays can get quite extensive scratch marks on one or more surfaces. These will soon fade or be covered with gravel etc so are not considered a detriment to the use of the product.