Upload
rashmiame
View
212
Download
0
Embed Size (px)
DESCRIPTION
SET 15
Citation preview
1. In a variable delivery pump i.e. Hydraulic pump:a) Provides a fixed amount of fluid at certain foot per revolution regardless of pressure:b) Is used to provide different amount of fluid as per demand of pressurec) As in 2 and out valve will automatically compensated for variable delivery of fluid
2. A riveted joint will subject of the:a) Tension loadb) Shear loadc) Bending loadd) Load
PAPER II(OCT’05)1. Chematic diagram drawing is
a) location of component are not indicatedb) component are indicatedc) components are located within the systemd) components location in a/c
2. Which material is slightly magnetic & rapidly react with concentrated nitric acid with greenish blue colour?a) carbon steel b) 18-8c) pure nickeld) monel
3. Size of flexible hose determined by a) inside dia in 1/16” incrementb) outside dia in 1/16” incrementc) inside dia in 1/32” incrementd) outside dia in 1/32 increment
4. Fuel lines identified by a) red colourb) blue colourc) green colour
5. Bolt with single raised dasha) AN corrosion resistant steelb) AN standard steelc) Aluminium alloy
6. AN 640 indicates a) bolt head and shank is drilledb) bolt with 10/32” diac) bolt shank is drilled
7. AN 121110 indicates a) bolt with 6/8 dia & head is drilled
8. Which washer is used when a bolt is installed at an angle to a surface or where perfect alignment with surface or where perfect alignment with surface is requireda) ball socket & seat washerb) lock washerc) plain washer
9. Which is used to tighten the Nut & Bolt where torque is critical
a) precision toolb) hox wrenchc) spanner wrenchd) torque wrench
10. Bolt with asterisk mark made of a) AN corrosion resistant steelb) AN standard steelc) Aluminium alloy
11. Which is difficult to soldera) Aluminium and its alloyb) Mg and its alloyc) Steel and its alloyd) Nickel
12. AN 170 AD 3-5a) round head rivet made of 2117 Al alloyb) universal head rivet made 2117 Al alloyc) universal head rivet made 2017 alloy
13. Which packing is effective in both direction in terms of pressure and back up is a) ‘O’ ringb) ‘W’ ringc) ‘V’ ring
14. Which chemical treatment converts surface of iron and steel parts to non metallic coil or absorptive , phosphade a) parco-lubrizingb) anodizing
15. Tempering is done in steela) to rlieve internal stressesb) to reduce brilleness and ductilityc) to increase strength and ductilityd) to barden
16. Which process is used to produce hard wear resistant surface or case cover strong & tough corea) case hardeningb) temperingc) normalizing
17. Mark the correct statementa) cold water ensure minimum corrosion resistance
b) hot water minimize distortion & alleviates crack
18. Lag between soaking and quenching causesa) precipitations from solid solution
19. To improve tensile strength, ductility and shock resistance of Mga) solution heat treatedb) precipitation heat treatedc) full annealing is done
20. which is used to check the hardness of all alloy Cu, Brassa) Barcol tester b) Rock well hardness testerc) Brinell hardness tester
21. Resistance of conductor doesn’t depend upona) material b) lengthc) shape of cross-section
22. M.M.F. is measured ina) Gilbert Symbol ‘F’b) Maxwell symbol ‘F’c) Weber
23. Which method is used to rapidly charge the batterya) constant voltage & varying current methodb) constant current & varying voltagec) varying voltage & varying current
24. Negative plate of Ni-cd battery made of a) Metalic cdb) Cd hydroxidec) Ni hydroxided) Nickle
25. What is frequency in 4 pole generator, conductor is turning at 1500 rpma) 60 cpsb) 50 cpsc) 120 cps
26. What is total inductance of three inductors of 2.3.4 henrya) 1.9 (series)b) 0.9 (parallel)
27. In circuit when capacitive reactance is equal to inductive reactancea) resonantb) phase in
28. Ionization potential of gas diode depends upona) plate current b) cathode constructionc) size of tubed) type of pressure of gas
29. With gate open, SCR conducts when applied voltage a) peak inverse voltageb) break over voltagec) cutt off voltage
30. The minimum no. of diode in half wave rectifiera) 1b) 2c) 3d) 4
31. To prevent generator from motoringa) reverse current cut out relayb) voltage regulatorc) circuit breaker
32. The purpose of equalizing circuita) to lower voltage of high generator and raise voltage of low
generatorb) to raise voltage of high generation and lower voltage of low generation
33. In which line current equal to phase currenta) Delta connected Alternatorb) Star connected Alternatorc) Three phase Alternator
34. Series D.C. motora) Poor voltage reputationb) Firld winding made of few turn of heavy wirec) High starting Torque (principal advantage)d) Both (a) & (b)
35. Which ATA code indicate hydraulic power, Fire protection, pneumatic enginea) 29, 26, 36, 77b) 25, 26, 36, 77c) 29, 28, 36, 77
36. In PMI Nickel plated surface doesn’t give indication of:a) flawb) fine discontinuitiesc) Ferrous parts onlyd) Both ferrous & non ferrous parts
37. In oil & chalk process, defect is indicated as:a) dark gray line with light gray backgroundb) light gray line with dark gray backgroundc) white line in green background
38. In Radiography ‘X’ ray equipment are graded according:a) voltage rangeb) frequency rangec) ampere range
39. Which process reveals (surface defects) subsurface defect, subsurface defect, water in honey comb material:a) Dye penetrant Processb) M.P.I.c) Radiography
40. Small a/c tied down:a) alter each flightb) every heightc) before storm
41. Which extinguisher is best for electrical fire?a) CO2
b) Dry chemicalc) Waterd) Cd4
42. In swept wing a/c de fueling procedure starts from:a) outboard wing tank firstb) inboard wing tank first
43. In pressure fueling:a) Pressure of fuel pump must be at min. filter pr.b) Pressure must be correct for refueling system
44. Bottle jack is used for:a) single wheel or all wheel of single unitb) single wheelc) single brake unit
45. Which is equivalent to 4 bit:a) Nibbleb) Bytec) K.B. (Kilo Byte)
46. Modem is:a) Input/output peripheralb) Hardwarec) Softwared) Operating system
47. Which decimal no. is equivalent to (110.001)2
a) 6.25b) 6.125c) 6.50
48. Which is responsible for high lift capacity of Glider:a) high aspect ratiob) symmetrical wingc) Thickness/chord
49. When tail wheel a/c facing in wind:a) elevator should be fully upb) elevator should be fully downc) elevator should be in neutral position
50. Angle of attack:a) Is acute angle between longitudinal axis of a/c & chord of wing
direction.b) Is horizontal angle between direction wind & plane of symmetry of a/cc) Is acute angle between chord of airfoil and direction of wind
51. Aspect ratio:a) span/mean chordb) span/cross sectional areac) chord/spand) area/span
52. Primary control surfaces are:a) aileron, rudder, elevator
b) aileron, rudder, elevator, L.E. flapc) aileron, rudder, elevator, T.E. flap
53. In four stroke engine five events are:a) intake, compression, ignition, power, exhaustb) intake, compression, exhaust power.c) intake, power, exhaust, compression.
54. Which welding process uses consumable electrode:a) TIGb) MIGc) Plasma are welding
55. Which hammer used in narrow place:a) Ball peen hammerb) Cross peen hammerc) Hide hammerd) Plastic head hammer
56. Which one give smoother surface:a) single cutb) double cutc) second cutd) smooth cut
57. When using hacksaw blade in which direction it gives better result:a) forward strokeb) backward strokec) fined) coarse
58. What is the position of adjustment screw in fine adjustment:a) upper positionb) lower positionc) neutral positiond) central position
59. Which is used to mark rivet holes when using original template to lay out a skin pattern on the new surface is:a) center punchb) prick punchc) transfer punch
60. Which is used to clean clogged male threaded fastener:a) die nut
b) tapc) two part adjustable die
61. Taper tap is used in tapping procedure during starting the tap used for starting operation:a) Taper tapb) Plug tapc) Bottoming tap
62. Which screw driver is used during verneal space limitation:a) off-set screw driverb) stubby screw driverc) simple screw driver
63. If 1 cm. of main scale is divided in 20 equal part, 24 division of main scale is equal to 25 division of vernier scale. Least count is:a) 0.0002 mm.b) 0.002 cmc) 0.02 inchesd) 2 cm
64. Which thread gives/takes great strength/load in one direction:a) buttress threadb) square thread
65. ‘V’ block is used to:a) to hold cylindrical objectb) to hold square object
66. Which one is in increasing order to strength:a) 2S, 24ST, 17ST, A17STb) 2S, A17ST, 24ST, 17STc) 2S, A17ST, 17ST, 24STd) 2S, 17ST, A17ST, 24ST
67. In flexible hose, slack is given:a) 2 to 3% of total lengthb) 5 to 8% of total lengthc) 3 to 9% of total lengthd) 10% of total length
68. Which has greater tensile strength & lower compressive strength:a) carbonb) graphitec) boron
d) aramid
69. Mark the correct statement:a) turbo fan engine require lesser runway length for take off than jet
engine.b) Jet engine, at higher altitude is efficient in comparison with piston
enginec) Jet engine has more weight to get equivalent powerd) Turbo jet engine requires longer runway.
70. Modern digital computer consist of:a) Central processor (CPU) input/output deviceb) Hardwarec) Software
71. Speed of motor increases when load decreases current decrease because of:a) frictional loss between motor’s moving partb) frictional loss between winding & other partsc) induced back emf increases
72. Jo bolt is:a) externally threaded two piece rivetb) externally threaded three piece rivetc) internally thread three piece rivet
73. For parallel A.C. generators:a) voltage, phase equalb) phase, frequency samec) voltage, frequency phase
74. Quantity & quality of X-ray depends on:a) intensity and penetrating power of x-rayb) frequency & penetrating powerc) frequency & intensity of x-ray
75. 7075-0 indicates:a) normalizingb) annealedc) hardened & tempered
76. Gasoline having octane no. more than 100 indicated by:a) octane no.b) performance no.
77. Which is used to form rivet head:
a) snap and dollyb) hammer and punchc) punch & plierd) rivet & bucking bar
78. De-magnetization is done in megnaflux method, after magnetization:a) By slowly moving parts out of magnetic field demagnetize the
part after magnetic flow inspection byb) The parts are demagnetize by passing D.C.c) By flowing A.C. through the part and the part is immediately taken out
of the electromagnetic field
79. A bolt should be installed (with load):a) Upward & downwardb) Upward & forwardc) Downward and forwardd) Downward and rearward
80. Ventral fin is used for:a) Directional stabilityb) Longitudinal stabilityc) Lateral stabilityd) Both (b) & (c) are correct
PAPER-II FEBURARY 2006
1. Small aircraft should be tied downa) After each flightb) Every flightc) Before storm
2. Which extinguisher is best for electrical fire:a) CO2
b) Dry chemicalc) Water
3. In pressure fuelinga) Pressure of fuel pump must be at minimum filter pressureb) Pressure must be correct for refueling system
4. Bottle jack is used for:a) Single wheel or all wheel of single unitb) Single wheelc) Single brake unit
5. When tail whell A/C is facing in wind:a) Elevator should be fully uplockedb) Elevator should be fully downlockedc) Elevator should be in neutral position
6. ‘V’ block is used to:a) to hold cylindrical objectb) to hold square object
7. Lift is due to:a) Pressure drop on upper surface of wingb) Pressure drop on lower surface of wingc) Velocity increase at lower surface of wing
8. Which of the following gate represent parallel switch circuit:a) ANDb) NANDc) OR
9. Long shunted compound wound generator has:a) Shunt field across both armature and series fieldb) Series field across both armature and series fieldc) Shunt field across armature only
10. Neoprene is non-compatible to:
a) weatherb) non-aromatic fuelc) aromatic fueld) naphtha
11. High-tigue has:a) chambered fitb) reamed fitc) interference fit
12. 18-8 steel is:a) 8% chromium and 18% Nickelb) 18% chromium and 8% Nickel
13. Regarding margin of drill, mark the correct statement:a) Margin to a drill prevent binding of drill during drilling deep holesb) Is a difference between inner and outer diameterc) Is a difference between helix angle and flute angle
14. Main alloying element of 2024 is:a) Nickleb) Copperc) Magnesium
15. Modulus of Elasticity is the ratio of:a) Stress/Strain within elastic limitb) Stress/Strain above elastic limitc) Strain/Stress within elastic limit
16. Mark the correct statement:a) Phcostat has three terminalb) Potentiometer has three terminal and has low resistance valuec) Phcostat has two terminal and has low resistance
17. Interior cleaning of aircraft is done by:a) Detergent and soapb) Phosphoric acidc) Vacuum cleaner
18. Best suited for checking discontinuity is:a) ammeterb) ohmmeterc) bonding tester