Senzor OSD User Manual_ V152

  • View
    10

  • Download
    6

Embed Size (px)

DESCRIPTION

Senzor OSD User Manual, Senzor OSD User Manual, Senzor OSD User Manual,

Transcript

  • 2

    This page left intentionally blank

  • Table of contents

    3

    Table of contents

    1. INTRODUCTION TO THE OCCUSWITCH DALI ..................................................................................................... 5

    2. OPERATING PRINCIPLE .................................................................................................................................... 6

    2.1. OCCUSWITCH DALI VERSIONS ..................................................................................................................................... 6 2.1.1. OccuSwitch DALI Basic (LRM207x) ............................................................................................................... 9 2.1.2. OccuSwitch DALI Advanced (LRM208x) ..................................................................................................... 10 2.1.3. OccuSwitch DALI BMS (LRM209x).............................................................................................................. 11 2.1.4. Extension movement sensor (LRM8118) ................................................................................................... 12

    2.2. LUMINAIRE CONTROL ............................................................................................................................................... 13 2.2.1. DALI group assignment .............................................................................................................................. 13

    2.3. AUTOMATIC CONTROL .............................................................................................................................................. 14 2.3.1. Occupancy ................................................................................................................................................. 14 2.3.2. Daylight Dependent Regulation ................................................................................................................. 14

    2.4. LOCAL CONTROL ...................................................................................................................................................... 16 2.4.1. Infrared group addressing ......................................................................................................................... 16 2.4.2. Manual control on IR channels .................................................................................................................. 17 2.4.3. Relation between IR channels and DALI groups ........................................................................................ 17 2.4.4. Manual control with the IRT8050 and UID8510 ........................................................................................ 18 2.4.5. Manual control with the IRT8010 .............................................................................................................. 18 2.4.6. Local control with standard switches and the LCU2070 ............................................................................ 19 2.4.7. Presets ....................................................................................................................................................... 20 2.4.8. Local control of multiple OccuSwitch DALI ................................................................................................ 20

    3. APPLICATION DESIGN.................................................................................................................................... 21

    3.1.1. Luminaire output ....................................................................................................................................... 21 3.1.2. Use area ..................................................................................................................................................... 21

    3.2. SELECTING THE OCCUSWITCH DALI TYPE ..................................................................................................................... 24 3.2.1. OccuSwitch DALI or extension sensor ........................................................................................................ 24 3.2.2. Type of OccuSwitch DALI ........................................................................................................................... 25

    3.3. SELECTING THE OCCUSWITCH DALI MODE ................................................................................................................... 25 3.3.1. Parallel operation and open plan mode (mode 9) LRM208x only ............................................................. 27

    4. COMMISSIONING ......................................................................................................................................... 30

    4.1. CONFIGURE CONTROLS AND SWITCHES ........................................................................................................................ 31 4.1.1. IRT8010 ...................................................................................................................................................... 31 4.1.2. IRT8050 ...................................................................................................................................................... 32 4.1.3. UID8510 ..................................................................................................................................................... 33

    4.2. CONFIGURE THE OCCUSWITCH DALI .......................................................................................................................... 34 4.2.1. Checks ........................................................................................................................................................ 34 4.2.2. Hold timer .................................................................................................................................................. 34 4.2.3. Assigning luminaires to DALI groups ......................................................................................................... 34 4.2.4. Calibration of the required light level ........................................................................................................ 35 4.2.5. 100 hour burn-in mode .............................................................................................................................. 37 4.2.6. Request application mode ......................................................................................................................... 37 4.2.7. Mass programming ................................................................................................................................... 38 4.2.8. Set application mode ................................................................................................................................. 38 4.2.9. Background level ....................................................................................................................................... 38 4.2.10. Power-up state .......................................................................................................................................... 39 4.2.11. Infrared group address .............................................................................................................................. 39

    4.3. RESET TO FACTORY DEFAULTS .................................................................................................................................... 40 4.4. WALK TEST ............................................................................................................................................................ 41

  • Table of contents

    4

    5. OCCUSWITCH DALI BMS (LRM2090 AND LRM2092) ........................................................................................ 42

    5.1. INTRODUCTION ....................................................................................................................................................... 42 5.2. USING A UNIVERSAL DALI CONTROLLER ....................................................................................................................... 42

    5.2.1. Pitfalls and exceptions ............................................................................................................................... 42 5.2.2. Shared Occupancy Control ......................................................................................................................... 42

    5.3. USING A UNIVERSAL DALI GATEWAY ........................................................................................................................... 43 5.3.1. Pitfalls and exceptions ............................................................................................................................... 43 5.3.2. Shared Occupancy Control ......................................................................................................................... 44

    5.4. USING THE LOYTEC DALI GATEWAY ............................................................................................................................ 44 5.4.1. Energy measurement ................................................................................................................................. 44 5.4.2. Occupancy signal ....................................................................................................................................... 44 5.4.3. How to use the combination of OccuSwitch DALI and gateways? ............................................................. 45 5.4.4. Cascading DALI network ............................................................................................................................ 45 5.4.5. OccuSwitch DALI ..........