SELF INSTALLATION MANUAL - Minshan · Installation method and process of Satellite Antenna WX-75B strut： 2.1.1. Preparation work： Installation tools required （ • 6-8 Wrench

Make Life Smart

'A proud subsidiary of Minshan Industry Group'

SELF INSTALLATION MANUAL

Make Life Smart


Satellite Antenna WX-75B strut installation specification:：

1. The components of Satellite Antenna WX-75B strut:：

Satellite Receiving Antenna WX-75B

Satellite strut accessory

LNB（Fixed by black buckle（

1

Satellite Antenna WX-75B Strut Installation Instructions

Installation method and process of Satellite Antenna WX-75B strut：

2.1.1. Preparation work：

Installation tools required（ • 6-8 Wrench • Cross screwdriver • Electric hammer

2.1.2. The site selection of satellite antenna installation

The site selection of satellite antenna is important for the location of satellite antenna installation. The local natural environment and electromagnetic field must be considered for the satellite antenna erecting, and the option of erecting field is particularly important. The following must be considered for the location option of satellite antenna installation.

1. There should be no obstruction in the direction of the satellite that paraboloid points, which means a wide vision for the direction of satellite. The satellite receiving antenna should be erected on the local wide and open top as high as possible, avoiding the obstructing to the antenna wave beam from barriers such as hills, forests, as well as high building to name a few.

2. A firm foundation must be guaranteed for the satellite antenna erection, which could fully bear the weight of the antenna itself, to prevent it from dislodging when it collapses or huge wind occurs.

3. No interference source should exist around the satellite antenna. Antenna periphery should avoid radar station, transposer station, micro wave communication station, radio station as well as high voltage electric wires.

4. When erecting receiving antenna, particularly around a primary school in the countryside, be careful not to block the satellite wave beam from the school building, the wall, as well as woods, and take caution for the safety of students and the antenna itself. The installation should be done where it is not easily accessible to children.

5. Outdoor installation position and indoor receiving distance should be as close together as possible when satellite antenna erection is being done, and the coaxial cable combined to the satellite receiver should be also as close together as well, which could reduce the signal loss attributing to the long transmission line. Generally speaking, the length of coaxial cable should be within 40m, while waterproof is processed for the cable connector.

Make Life Smart


2

Make Life Smart


3

Serial number

Name of the part Specification Drawing code Dosage Unit Note

1 Fixed plate SPCC T=2 WX-75B-01 1 PCS

2 Adjusting plate SPCC T=2 WX-75B-02 1 PCS

3 Fixed buckle Q235 T=3 WX-75B-03 2 PCS

4 B type of antenna paraboloid

WX-75B-04 1 PCS

5 Fixed tube WX-75B-05 1 int

6 Fixed tube cap PP WX-75B-06 1 PCS Partly required

7 Feed strut Square tube19*19*1.0 WX-75A-010 1 PCS

8 U type buckle-19 SPCC 2.0 WX-75A-006 1 PCS

9 Feed rod Circle tube：12-0.6 WX-75A-007 2 PCS

10 Snap-gauge SPCC 2.5 WX-75A-011 1 PCS

11 Snap ring ABS 1 PCS

12 Support ABS 1 PCS

13 Galvanized bolt M8*80 Galvanized 4 Set 1 Nut, 1 Flat washer, 1 Spring washer

14 Galvanized hexagon bolt

M6*35 Galvanized 2 Set 1 Nut, 1 Flat washer, 1 Spring washer

15 Semicircle strength bolt M6*35 Galvanized 1 Set 1 Nut, 1 Flat washer, 1 Spring washer

16 Semicircle strength bolt M6*20 Galvanized 6 Set 1 Nut, (1 Flat washer M8, T=2),1 Spring washer

17 Semicircle strength bolt M6*30 Galvanized 4 Set 1 Nut, 1 Flat washer, 1 Spring washer


M8*150 Galvanized 1 Set 3 Nuts, 4 Flat washers, 1 Spring washer


M6*12 Galvanized 3 Set 1 Nut, 1 Flat washer, 1 Spring washer

20 Galvanized cross bolt M3X15 Galvanized 1 Set 1 Nut

2.1.3. Installation of satellite antenna strut：

Make Life Smart


4

1. Components of antenna strut（upward according to the arrow pointing（

2. Assembling the feed rod and feed strut Model 1), see below Feed rodFeed strut

Note:：The square hole is upward when assembling the feed strut, and the short flat part of the feed rod is combined with the strut.

3. Fixed plate, U type buckle, antenna paraboloid B assembling (Model 2), see below ReflectorFixed plateU type buckle-19

4. Adjusting plate, assembling of adjusting plate and fixed-buckle（Model 3)（see below

Fixed buckleAdjusting Plate

Make Life Smart


Note:：The arrow on the fixed plate is in accordance with the arrow on the antenna paraboloid B type (upward); the U type buckle-19 is on the outer edge of antenna paraboloid B type.

Note:：The screws should not be tightened when assembling, which is convenient for the fixed tube installation and the antenna angle adjustment.

5. Model 1（Model 2（Model 3（LNB（Fixed tube assembling Model 1Fixed tubeModel 3Model 2LNB

Note:：The arrow on the fixed plate is in accordance with the arrow on the antenna paraboloid B type (upward); the U type buckle-19 is on the outer edge of antenna paraboloid B type.

5

Make Life Smart


6

Frequently Asked Questions：

General informationA Digital Satellite Decoder(DVSH：362)is a convenient product that allows you to view a variety of programs provided through satellite technology.This user’s guide covers the installation of the DVSH：362 and the necessary steps to implement various features.This also explains special features available only in this document subject to change.We reserve the right to make changes in product design or specifications as progress in engineering or technology may affect the functionality.

General operationThroughout this manual you will notice that the everyday operation of the decoder is based on a series of user friendly on：screen displays and menus.These menus will help you get the most from your decoder, guiding you through the installation, channel organizing,viewing and many other functions. All functions can be carried out by using the buttons on the Remote Control, and certain functions can also be carried out by using the buttons on the front panel of the decoder. The decoder is easy to use, always at your command and adaptable for future advance.

Please be aware that new software may be issued in future and the new functionality of the decoder would be comple-mented accordingly. Should you meet any difficulties with the operation of your decoder, please consult the relevant sectionof this manual, including the troubleshooting.

Activation serviceThis decoder needs to be activated with OVHD in order to view channels. Activation can be done with your cellphone, please see details below:

The Service will timeout if no response is received from you within 30 seconds. Please have your STB Number and/or Smart Card Number available before using this service. The STB needs to be activated one time before programs can be received.The STB should be completely installed before you activate the STB. Activation can be done via the USSD system on a cell phone with the OVHD Self Help Service. To activate your STB, please dial *120*OVHD# or *120*6843#(premium rates ap-ply)and select option. Activate Set Top Box and then compile the message and send it to the front on your mobile phone ordevice and then follow the service’s instructions. Your STB should become active within a few seconds to a few minutes once this process has been successfully completed on your phone or mobile device.

Make Life Smart


7

button FunctionPower STB Standby on/offMute STB mute on/off0-9 Channel inputBMAIL Display Broadcast Mail boxEPG Display Electronic Program GuideMENU Display Main MenuINFO Show Information Bar and information of the current

and next programBACK Return to previous Channel or MenuEXIT Exit from the current menuUP

Navigation buttons for menus and select channel or change volume

DOWNLEFTRIGHTVOL+/- Adjust volumeP+/- Select next or previous channelOK Display channel list or confirm operationRED Display the Channel informationSUB/TXT Active Subtitle functionAUDIO Audio mode(Left,Right,Stereo)TV/RAD Switch between TV and Radio modeLANG Select different channel languagesLIST Display the channel listHELP Enter the system information(Diagnostics)FAV Display the favorite listASP RAT Saved for future use<< Saved for future use >> Saved for future use> Saved for future use|| Saved for future use

Front Panel

Remote Control Unit

button FunctionPower STB Standby on/offMute STB mute on/off0-9 Channel inputBMAIL Display Broadcast Mail boxEPG Display Electronic Program GuideMENU Display Main MenuINFO Show Information Bar and information of the current

and next programBACK Return to previous Channel or MenuEXIT Exit from the current menuUP

Navigation buttons for menus and select channel or change volume

DOWNLEFTRIGHTVOL+/- Adjust volumeP+/- Select next or previous channelOK Display channel list or confirm operationRED Display the Channel informationSUB/TXT Active Subtitle functionAUDIO Audio mode(Left,Right,Stereo)TV/RAD Switch between TV and Radio modeLANG Select different channel languagesLIST Display the channel listHELP Enter the system information(Diagnostics)FAV Display the favorite listASP RAT Saved for future use<< Saved for future use >> Saved for future use> Saved for future use|| Saved for future use

Front Panel

Remote Control Unit

Remote Control Unit：

Front Panel：

Make Life Smart


8

Connecting Introduction：

• Connecting to TV via HDMI Cable

• High Definition(HD) HDMI connection is required to view HD channels in High definition.

• Connection to TV via RCA cable

• Standard Definition (SD)

• Connection multiple Decoders

Menu Tree

Once you have properly installed and connected cables of the decoder, Press the MENU button on your remote control to display the main menu.

The main menu tree consists of five items listed below.• Installation• Edit• Setting• Tools• Game

Make Life Smart


9

Menu Tree：

Use the < > buttons on your remote control to move between items on the menu bar and to select an item inside a submenu. Use the ：： buttons to move up and down between items in the menu.

This menu is used during installation to search the channels and set the satellite antenna(Dish). These settings usually do not need to be changed after installation.

The main menu tree consists of 3 items listed below:• Antenna setting• Program search• Edit TP• Press OK into the menu.

The system password is 0000.

Installation：

Make Life Smart


10

1.1 Antenna setting

Usually the parameter does not need to be changed. Changing these settings should only be done by an installer or experienced users as changing these settings could cause your decoder not to receive programs. Enter the menu with password.

Enter the menu with password.

Scan mode• Preset: Search channels by the preset TP.• Single TP: search channels by the Single Frequency.

Free Only• Channel mode :FTA+CAS or FTA

Channel Type• Searching channel type: ALL,ALL TV,ALL Radio

Network search• Yes:Search will use NIT list.

1.2 Program search

Make Life Smart


11

No:Do not use NIT ,only Preset TP search.

Frequency• TP list only uses the Scan mode of Single TP.• Usually the parameter dose not need to be changed.• If you are sure of your select mode, Press the Blue button to Start the Search. You can get your Channels• by the end of the search.• If you want to change the Dish parameter, you can Press the Green button to.

Make Life Smart


12

The Antenna Setting Menu

1.3 Edit TP

• This menu has 3 preset TP. The three TP cannot be modified or deleted.• If you want to add TP, press Green button.• If you want to modify the select TP of the list ,please press the Blue butto

Edit

The main menu tree consists of 4 items listed below.• EPG• Edit Channel• Edit Fav Channel• Saved Channel

Make Life Smart


13

Press OK into the menu.The system password is 0000.

2.1 EPG

There is Weekly EPG, and it shows this information focused on what is showing over the next week. You can book what programme you want to watch ,then the programme will automatically remind you and play the programme at the start time.• Use the Up and Down button to select and play the channel.• Use the Left and Right button to select the Days.• Use the RED button to switch the channel list and program list.

Make Life Smart


14

If currently focusing the program list, you can Press the OK button booking the program.

If you want to check the booking programme list ,you can press the YELLOW button into the “Saved Channel”Menu.

If the programme has Introduction, it will display the icon “i”, when you select the item you can press the INFO button, which will display the introduction of the program.

The system password is 0000..

2.2 Edit Channel

Make Life Smart


15

In this menu you can edit the channel, such as Hide, Skip ,Move, Lock.

If you press RED button the channel will be hidden, it does not display the Full screen play list.

If you press GREEN button, the channel will be skipped in the play list.

If you press YELLOW button, the channel will move position. Use thefunction by following steps:1. Press the yellow button2. Use up or down button to move to the position you want3. Press yellow button, then complete move.

If you want to lock the channel, press the BLUE button. If the channel is locked when you select it, you will be required to input the system password.

Make Life Smart


16

2.3 Edit Fav Channel

2.4 Reserve Channel

This function adds your channel by favorite type. Please refer to the help information on how to add the favorite channel and the favorite type.

If you add the favorite channel, you can press the FAV button in the full screen, then it will display the favorite list.

In this menu you can view reserved channel.• Press UP or DOWN button, you can select reserved channel.• If you press RED button, the reserved channel will be deleted.• If you press YELLOW button, you can edit• Timer Mode of the reserved channel.• Press MENU button, you can return to previous menu. Press EXIT button, you can exit to full screen play.

Make Life Smart


17

3. Setting

The main menu tree consists of 6 items listed below.• Language• Time Setting• A/V Setting• Display Setting• Parental Control

Password Setting

3.1 Language

1. OSD language: Only supports English.2. Subtitle: Select between On and Off.The default is Off.If you select On, subtitle will be turned on.

Make Life Smart


18

3.2 Time Setting

3.3 A / V Setting

1. GMT Usage:Select Auto to have the time zone configured automatically or select User Define to select the time zone yourself. The default setting is Auto.

2. GMT Offset:Choose your time zone here if “GMT Usage”is first set to User Define.3. Summer Time:Select between On and Off.The default is Off.If you select On,time will be 1h faster than actual time.

Same Audio Output :Select between No and Yes.Select Yes to independently increase or decrease the volume of only some channels That might be louder of quieter than the other channels.The default is No.

Audio Output:Select among Stereo,Left and Right.The default is Stereo.Dolby Audio: Select between PCM and RAW.The default and recommendation is PCM.Only use RAW with some Dolby surround sound systems.

Screen Ratio: Use 16:9 with a “Flat Screen”LCD/LED TV and only use 4:3 with an older“Box” orCRT TV.Auto will change theoutput scale depending on the scale of the picture content being displayed.The default is Auto.

SD Video Mode SD:This controls the format of the picture system that is sent out of only “AV OUT” port on your decoder.The default is PAL.Use PAL wherever possible as it results in Better picture quality.You can change this to NTSC if this is the only format that your TV supports.

HD Video Mode:This setting controls the resolution of the picture sent to your TV via the HDMI port ofthe decoder.Bigger numbers result in better quality pictures.The default is 1080P60HZ.When you changethis setting,your decoder will change the setting .

Make Life Smart


19

7.Picture Scaling:Select among FULL,LETTERBOX and PAN&SCAN.You canselect it according to personal preference.

3.4 Display Setting

Menu Transparency: This controls how transparent the menu,volumebar and info bar will be displayed.The default is Opacity.Adjust the setting accordingto your preference.

Video Brightness:This controls how bright the video will be displayed.The default is 50.Adjust the setting according to your preference.

3.UHF Channel:This controls the channel number that the decoder will send a picture from its RF OUTport.The default is CH63.Make sure your TV is tuned to this same channel if you use the RF OUT port onyour decoder.

4.UHF Mode:This controls the TV system format that the decoder sends out of the RF Out port.Thedefault is PAL I.You can select PALDK or PAL BG if your TV only supports one of these two TV systems.

5.Banner Time:This controls how long the info Barremains on the screen after use.

3.5 Parental ControlParents can lock programs which are not suitable for their childrento watch,depending on parental guidance rating of the programby Choosing an appropriate level.The default Control Passwordis 1234.You can change it according to your habit.Select ParentalControl level from OFF,ALL,PG：10,10,PG：13,13,16,18 and R：18.

Make Life Smart


20

Please call Customer Care Center,if you forget the Parental Control PIN.

3.6 Password Setting

4.Tools

The default password is 0000.You can change it According to your habit.If you forget it,please call Customer Care Center.

Channel Lock:Select between Off and On.When “On” is selected,you can not view the locked Channels until you enter the correct password.Menu Lock:Select between On and Off.When “On” is selected,you require

A password to change some important settings.

The main menu tree consists of 3 items listed below.Factory Reset

System information Mail

Make Life Smart


21

4.1 Factory Reset

To reset the decoder back to factory defaults,select Factory Default and press

OK button.Before entering into the Factory Reset window,you need to input the correct password.The default is 0000.Then a warning message will be Displayed to confirm,select OK and press OK.

Warning :You will lose all of the data and information,which was installed In terms of your choices for favorite channels and channel lock/ Skip/move/hide.

System Information

Make Life Smart


22

4.1 Factory Reset

To reset the decoder back to factory defaults,select Factory Default and press

OK button.Before entering into the Factory Reset window,you need to input the correct password.The default is 0000.Then a warning message will be Displayed to confirm,select OK and press OK.

Warning :You will lose all of the data and information,which was installed In terms of your choices for favorite channels and channel lock/ Skip/move/hide.

This will show some information about the Decoder,CA ID + checksum, Software version,Hardware version, Driver version, Loader version,Smart Card and so on. You can press Pageup or Pagedown to view more information.

System Information

Make Life Smart


23

4.3 Email

Press UP or DOWN button to select the mail.Press OK button to read it.Press Exit button to quit.Press RED button to delete the selected email.Press BLUE button to delete all email.

You can easily read your email by pressing Hot button “email”.

Game

The main menu tree consists of 3 items listed below.• Tetris• Push Box• Guess Number

Make Life Smart


24

5.1 Tetris

Press UP button to rotate block.Press DOWN button to move down quickly .Press L/R button to move block Towards left/right.Press Enter button to move Block down to bottom.Press RED button to suspend game.Again press RED button to start game.

5.2 Push Box

5.3 Guess Number

Press Pageup or Pagedown to select the level.Press Direction button to move box.If you want to go back to the previous position,you can press the Enter button.You pass the level after pushing all boxes to specified position.

The system will generate a random number.If You guess the correct number,you will win.You can press BLUE button for more information.

Make Life Smart


25

6.Full Screen6.1 Channel information Bar

Press INFO button on full screen,Channel Information bar will display.You can view some Information about current program,such as name, current event info, next event info, scale, resolution, audio track.

6.2 Channel information

Press HELP button to display channel information.You can view some information,such as TS ID,Network Information, Signal Strength and Signal Quality, Video PID, Audio PID, Frequency.

6.3 Channel list

6.4 Mute

Press OK button to display channel list.You can view all programs.Press L/R to switch between TV and Radio list.

Press MUTE button,you can see a mute icon on the full screen and turn off the volume.Again press MUTE button to restore the volume.

Make Life Smart


26

6.5 Volume

6.6 Audio

6.7 Language

To increase or decrease the volume,press LEFT/RIGHT button on the remote control.

Press AUDIO button repeatedly to select one of Three possible audio settings(Stereo,Left and Right).The current audio setting will be displayed on the info bar at the bottom of the screen.

Press LANG button on the remote control to open the audio language window on the screen.Press EXIT button to exit.

6.8 Subtitle Language

Press SUB/TXT button to open the subtitle language window on the screen.If there is no Subtitle,system will inform “No subtitle language”.Press EXIT button to exit.

Make Life Smart


27

Trouble Shooting

Problem Possible causes What to do

Neither red light nor green light is on from the front panel.

12V power cable is not plugged into the back of the decoder：and external power supply is not properly plugged into the mains socket.External power supply is broken.12V

Check whether the green light on the external power supply is on or not, if not, ensure that the mains switch is on and if so, try plugging the external power supply into a different mains socket.If the green light on the external power supply still can not switch on then maybe the external power supply is broken.

No sound orpicture but the redlight on the frontpanel is on.

Rain clouds can sometimesaffect the satellite signal andcause loss of picture and sound.

If the message is shown formore than a few hours.

This is normal and will only last from 5 minutes to a few hours depending on where the rain clouds are.

Your Satellite Dish might not be pointingproperly at the Satellite.There might be aproblem with your LNB or cable from the dish to the LNB IN connector on the back of your decoder.You might need to call an installer to fix installation.

Some of TVchannels seem tobe missing.

You are viewing channels from afavorite group that doesn’tinclude all available channels.

The channels that are missinghave been “skipped” in “EditChannel”.

Navigate to “Channel List” by pushing OK on the remote control while watch-ing full screen and then press left or right arrow button to select TV or Radio list.

Remove the skipped channels in “EditChannel”.

The remote controlis notWorking.

Batteries are flat(no light flashes on the remote control when you push any button)

Remote control is not properlypointing at decoder or someobject is blocking the front panelof decoder from your remotecontrol.

Replace the batteries.

Point the remote control at Decoder or ensure that no Object is blocking the front Window of the decoder.

Note:If you have tried all of the actions suggested above without solving the problem,please contact your dealer or service provider.

Make Life Smart


28

Warranty Card

The distinguished customers, we appreciate your use of our products.To guarantee your rights and interests, please read the following points carefully.1. This is the necessary certificate for the free of charge after-service of our products which are within the warranty time period Please fill up this card carefully together with the distributor whilst buying the product, take good care of the warranty card and invoice as well. If there are any malfunctions, please contact the distributor with the warranty card and purchasing in-voice, or you can consult us for the service.2. ：We promise: If there are any malfunctions within 15 days dated from the sold day (date in the valid invoice),you can either choose to get the product repaired or change it. Free of charge repairing service can be offered for the malfunctions withinone year.：3. We offer pay service other than warranty service for the situations beyond the warranty time period.Without a warranty card or valid invoice.Disagreement of the type and serial number or erasure in the warranty card.Malfunctions caused by inappropriate use, retention or maintenance against the introductions.

Malfunction or damage caused by repairing, alteration and disassembly made by unqualified maintenance man.

Malfunction caused by fire, earthquake ,flood, lighting etc, natural disaster or other irresistibility and abnormal voltage.4. Invalid with copying or tearing up. No reissue under loss, please keep itwell.

Contact Information:

Tel: (041) 922 0309Fax: (041) 922 0182Address: 40 Melbrooks Avenue, Uitenhage, Eastern Cape, RSAEmail: [email protected] Website: www.minshan.co.za

Documents

SELF INSTALLATION MANUAL - Minshan · Installation method and process of Satellite Antenna WX-75B strut： 2.1.1. Preparation work： Installation tools required （ • 6-8 Wrench