Embed Size (px)
Citation preview
Page 1 of 24
CRL 10 1200 STANDOFF SYSTEMS
SECTION 10 1200
STANDOFF SYSTEMS PART 1 – GENERAL 1.01 SECTION INCLUDES A. Standard line of round and square standoffs, cap assemblies, tube style standoffs, edge grips, slot mount standoffs, accent rings, and mounting hardware. 1.02 RELATED SECTIONS
A. Section 05 0523 – Metal Fastenings B. Section 05 5000 – Metal Fabrications C. Section 05 5200 – Metal Railings D. Section 06 2023 – Interior Finish Carpentry E. Section 08 8000 – Glass and Glazing F. Section 09 7000 – Wall Finishes G. Section 10 1000 – Information Specialties H. Section 10 1400 – Signage 1.03 SUBMITTALS
A. See Section 01 3000 – Administration Requirements, for submittal procedures. B. Product Data: Manufacturer’s literature showing standard components, and installation instructions. 1. Include product data for anchoring into substrate.
C. Shop Drawings: Fabrication and installation. Include plans, elevations, sections, details, and attachments to other work.
D. Samples for Initial Selection: Manufacturer’s charts showing the full range of finishes available for products.
E. Warranty: Submit manufacturer warranty. 1.04 QUALITY ASSURANCE A. Manufacturer Qualifications: Company specializing in manufacturing standoff systems with a minimum five years of documented experience. Single source manufacturer. 1. The manufacturer must have a quality management system registration to the ISO 9001: 2008 standard. B. Installer Qualifications: Installer experienced in the installation of standoff systems similar in
complexity to those required for this project. 1.05 DELIVERY, STORAGE, AND HANDLING
A. Deliver materials to the job site in good condition and properly protected against damage to finished surfaces. B. Storage on site: 1. Store material in a location and in a manner to avoid damage. 2. Store material in a clean, dry location away from uncured concrete and masonry.
1.06 COORDINATION
Page 2 of 24
CRL 10 1200 STANDOFF SYSTEMS
A.Coordinate installation of anchorage for standoff systems. Furnish setting drawings, templates, and directions for installing anchorages, including anchor bolts, and any concealed base lugs. Deliver such items to project site in time for installation.
PART 2 – PRODUCTS 2.01 ACCEPTABLE MANUFACTURERS A. Basis of design: Design is based on Standoff Systems manufactured by:
C.R. Laurence Co., Inc. 2503 E. Vernon Ave. Los Angeles, CA. 90058 Toll Free Phone: (800) 421-6144 Toll Free Fax: (800) 262-3299 Phone: (323) 588-1281 Fax: (323) 581-6522 www.crl-arch.com email: [email protected]
SEE FOLLOWING PAGES FOR SELECTIONS (Specifier to eliminate Systems not used)
Page 3 of 24
CRL 10 1200 STANDOFF SYSTEMS
Page 4 of 24
CRL 10 1200 STANDOFF SYSTEMS
Page 5 of 24
CRL 10 1200 STANDOFF SYSTEMS
Page 6 of 24
CRL 10 1200 STANDOFF SYSTEMS
Page 7 of 24
CRL 10 1200 STANDOFF SYSTEMS
Page 8 of 24
CRL 10 1200 STANDOFF SYSTEMS
Page 9 of 24
CRL 10 1200 STANDOFF SYSTEMS
Page 10 of 24
CRL 10 1200 STANDOFF SYSTEMS
Page 11 of 24
CRL 10 1200 STANDOFF SYSTEMS
Page 12 of 24
CRL 10 1200 STANDOFF SYSTEMS
Page 13 of 24
CRL 10 1200 STANDOFF SYSTEMS
Page 14 of 24
CRL 10 1200 STANDOFF SYSTEMS
Page 15 of 24
CRL 10 1200 STANDOFF SYSTEMS
Page 16 of 24
CRL 10 1200 STANDOFF SYSTEMS
Page 17 of 24
CRL 10 1200 STANDOFF SYSTEMS
Page 18 of 24
CRL 10 1200 STANDOFF SYSTEMS
Page 19 of 24
CRL 10 1200 STANDOFF SYSTEMS
Page 20 of 24
CRL 10 1200 STANDOFF SYSTEMS
Page 21 of 24
CRL 10 1200 STANDOFF SYSTEMS
Page 22 of 24
CRL 10 1200 STANDOFF SYSTEMS
Page 23 of 24
CRL 10 1200 STANDOFF SYSTEMS
2.02 METALS
A. General: Provide metal free from pitting, seam marks, roller marks, stains, discolorations, and other imperfections where exposed to view on finished units.
B. Fasteners: Stainless Steel or Zinc. 2.03 GLASS PRODUCTS
A. Tempered Glass: 1. Install glass in accordance with section 08 8000, using template and cut out information as supplied by the manufacturer.
2. Thickness: As specified by the architect in the plans. 3. Polish edges that will be exposed to a bright flat polish. 4. Manufacturing Process: Manufacture fully tempered glass as follows: a. By vertical (tong-held) or horizontal (roller-hearth) process, at manufacturers
option, except provide horizontal process tongless and free of tong marks. b. Subject to compliance with requirements, provide safety glass permanently marked with certification label of Safety Glazing Certification Council or another certification agency, acceptable to authorities having jurisdiction. 5. Always use manufacturer supplied vinyl washers, so there is no metal to glass contact.
2.04 FINISHES A. Comply with NAAMM’s “Metal Finishes Manual for Architectural and Metal Products” for
recommendations for applying and designating finishes. B. Architect to Specify 1. Brass 2. Chrome 3. Satin Chrome 4. Brushed Stainless Steel 5. Polished Stainless Steel 6. Gun Metal PART 3 – EXECUTION
3.01 EXAMINATION
A. Examine substrates, where reinforced to receive anchors, to verify that locations of concealed reinforcements have been clearly marked for Installer. Locate reinforcements and mark locations if not already done.
3.02 INSTALLATION, GENERAL
A. Install in accordance with manufacturer’s instructions. 3.03 CLEANING
A. Immediately after installation, clean glass and metal surfaces with a mixture of mild soap and water. DO NOT USE abrasive cleaners on glass and metal surfaces.
Page 24 of 24
CRL 10 1200 STANDOFF SYSTEMS
3.04 PROTECTION
A. Protect glass and metal finishes from damage during construction period with temporary
protective coverings approved by manufacturer. Remove protective coverings at the time of Substantial Completion.
B. Restore finishes damaged during installation and construction period so no evidence remains
of correction work. Return items that cannot be refinished in field to shop; make required alterations and refinish entire unit, or provide new units.
END OF SECTION
