8/6/2019 Sanyo Service Manual
1/43
CONTENTS
Chapter One: Overview
Chapter Two: Port definition
Chapter Three: External setup item and Automatically identify the item
Chapter Four: Key definitionChapter Five: Key Function and Operation instructions
Chapter Six: BUS adjustment and Setup of item
Chapter Seven: Special function
CHAPTER ONE
OVERVIEW
. Overview
This software is apply for SANYO C-MOS 8BIT CPU LC8633XX series, and has ability
1
8/6/2019 Sanyo Service Manual
2/43
to control TV of I2C. This software is able to control LA76812 or LA76814, difference
application is in North America or the South America region. Below is the hardware
characteristic of this CPU and the brief introduction of the function that software
have.
1.1. LC8632XX hardware characteristic
1. 5128 bits RAM
2. 16K~64K ROM
3. OSD function
Screen for display:36 columns16 rows
Display RAM:3529 bits
1832 dots:248 fonts character
8 Character colors,8 Character background colors,8 Full screen colors
4. minimum bus cycle time of CPU 0.85 s
5. 16 I/O ports(Input and output can define)
6. 4-channel8-bit A/D converter
7. One-channel video signal input port (for CCD use)
8. 3-channel7-bit PWM output
9. Port of 3 I2C controls
10. 16-bit timer/counter
11. 16-bit timer/PWM
12. Remote control receiver circuit (take the noise rejection function)
13. 16-interrupt source,10-interrupt vectored, three level interrupt priority
14. A maximum of 128 levels subroutine application
15. CPU Standy function
16. Oscillation frequency:32.768KHZ(interference as low clock)
17. +5V5% single power input
18. High-performance 42pin,S-DIP package
1.2. The software function
1. Frequency tune. Can realize America region 181 channel.2. The examination function of EEPROMis realized when the TV set is switched
on, the alarm is happened if EEPROM has a mistake. If the new EEPROM is replaced,
then the initialization data is automatically written. The setup item all pass the
software to realize, the result is stored in EEPROM.
3. Single Color system of NTSC (LA76814), or three Color systems: PAL/ M, PAL/
N, NTSC.
2
8/6/2019 Sanyo Service Manual
3/43
4. BTSC. The BTSC IC can be used. When the TV is switched on, the TV
automatically detects whether is the BTSC IC or not.
5. The MONO or Stereo. When the BTSC IC is used, the stereo is realized,
otherwise the simple stereo is realized.
6. Auto fine Search. After switching on the TV set, if all of the position have noprogram, the Auto Search function automatically begin.
7. Factory mark function. The factory mark is displayed when switching on the
TV, namely Screen function. The remote control unit can change the contents of
factory mark.
8. At switching on the TV, the TV is fixedly placed in the POWER OFF state or not,
or according to the remembering of pass power.
9. One to three-channel AV input.
10. S- VIDEO input, the AV or S- VIDEO status is automatically selected according
to the S-VIDEO input connect or not.
11. The CCD function.
12. The V- CHIP of function.
13. Child Lock function.
14. WOOF function, the volume can be controlled. If the WOOF function isnt
selected, then the WOOF function can be changed for headphones.
15. Blue screen or blank screen function.
16. The TV key(program +/ , volume +/ , MENU, TV/ AV, POWER).
17. Remote controller (Transmitter IC: LC7461M-8103).
18. Four LANGUAGE MODE (English, French, Spanish, Portuguese).
19. Full Screen MENU and single line MENU control function.
20. AUTO Search, MEMORY, AIR/ CABLE function. When the Auto Search have
completed, the OSD display whether program is searched or not.
21. AFT function.
22. DIRECT Program Channel tuning, Program Channel REVIEW function, Program
Channel UP/DOWN. ( automatically skip the program number of " memory: power
off).
23. Bright, Contrast, Color, Sharp, Tint, Volume, Treble, Bass, Balance, WOOF
Volume and WOOF are realized by the IIC BUS, above all value is 100Step, the value
quickly skip by using the SKIP key.
24. The single key picture result control (Soft, Standard, Vivid, Bright, Memory
state, Factory 1 and Factory 2), " Factory 1" and " Factory 2" status is only used
under the " factory status".
25. The clock sets up, ON-TIME, OFF-TIME, BESPOKE TIME, ATTENTION, SLEEP
TIME function.
3
8/6/2019 Sanyo Service Manual
4/43
26. Mute function.
27. Auto Switch off when the TV has no signal over 10 minute. If the blue screen
function is selected, then the blue screen is displayed when the TV has no the
signal. The off-time and blue screen function is automatically canceled at " factory
," B/W balance, adjust and setup mode.28. Picture background noise control function ON/OFF.
29. IF automatic adjust box is used, the b/w balance can be automatically
adjusted at the BUS OPEN mode.
.Port Definition
2-1. LC8632XX terminal assignment layouts
1 SENSITIVITY Y/C ON/OFF 42
2 50/60 V-MUTE 41
3 ALARM TV/AV 40
4 WOOFER VOL AV1 39
5 VOLUME-L AV2 38
6 VOLUME-R MUTE 37
7 POWER WOOF ON/OFF 36
8 DEGAUSS SRS 359 GND IR 34
4
8/6/2019 Sanyo Service Manual
5/43
10 XTAL1 NC 33
11 XTAL2 S-VHS 32
12 VDD ENABLE 31
13 KEY1 SCL1 30
14 AFT IN SDA1 2915 KEY2 SCL0 2816 NC SDA0 27
17 RESET NC 26
18 FILT BLANK 25
19 CVBS-IN B OUT 24
20 V-SYNC G OUT 23
21 H-SYNC R OUT 22
2-2.CPU Terminal description
Number
Terminal Purpose Function Description
1 P10/SO0 SENSITIVITY Sensitivity control
2 P11/S10 50/60 50/60 output3 P12/SCK0 ALARM Clock output
4 P13/PWM1 WOOFER VOL PWM 1 output5 P14/PWM2 VOLUME-L PWM2 output
6 P15/PWM3 VOLUME-R PWM3 output7 P16 POWER Power on/off control signal output
port
8 P17/PWM DEGAUSS Degauss impulse output
9 VSS GND ground10 XT1 XTAL1 Input terminal for crystal oscillation
11 XT2 XTAL2 Output terminal for crystal oscillation12 VDD VDD Positive power supply
13 P84/AN4 KEY1 Key114 P85/AN5 AFT IN AFT input port
15 P86/AN6 KEY2 Key216 P87/AN7 NC No use
17 RESET RESET CPU reset port18 FILT FILT OSD filter
19 CVIN CVBS-IN Video input20 VS V-SYNC Vertical impulse input
5
8/6/2019 Sanyo Service Manual
6/43
21 HS H-SYNC Horizontal
22 R R OUT Red(R) output terminal of RGB image23 G G OUT Green(G) output terminal of RGB
image24 B B OUT Blue(B) output terminal of RGB image
25 BL BLANK OSD image signal
26 I NC No use27 P60/SDA0 SDA0 IIC data (IC)28 P61/SCLK0 SCL0 IIC clock (IC)
29 P62/SDA1 SDA1 IIC data (tune)30 P63/SCLK1 SCL1 IIC clock (tune)
31 P70/INT0 ENABLE Enable port32 P71/INT1 S-VHS S-video examine
33 P72/INT2 NC No use34 P73/INT3 IR Remote signal input
35 P00 SRS SRS switch36 P01 WOOF ON/OFF Woof on/off
37 P02 MUTE Mute38 P03 AV2 Av2
39 P04 AV1 Av140 P05 TV/AV TV/AV
41 P06 V-MUTE Mute42 P07 Y/C ON/OFF Y/C ON/OFF
2-3.Terminal control output status description
Note: The 0is instead of low level, and 1 is instead of high level as shown below.
1. Power control
Port Power on Power off
Pin7(power) 0 1
2. AV control
a). One-channel AV
Port TV AVPin39(AV1) 0 1
Pin38(AV2) 0 1
b). Two-channels AV
Port TV AV1 AV2
Pin39(AV1)
0 0 1
Pin38(AV2
)
0 1 1
c). Three-channels AV
Port TV AV1 AV2 AV3
Pin39(AV1
)
0 1 0 1
Pin38(AV2 0 0 1 1
6
8/6/2019 Sanyo Service Manual
7/43
)
3. 50/60 Output
Port 50 60Pin2(50/60) 0 1
4. Woof function: The CPU Pin36 is used as the WOOF ON/OFF control, then the
Pin4 used as the output control of the WOOF volume.
Port WOOF ON WOOF OFFPin36(WOOFER) 0 1
5. Left/Right-volume output: When the stereo control IC is not used, or the IC has
not stereo function, the simple stereo function is automatically realized, at this time
the CPU pin5 and pin6 are used as the Left /Right-volume output.
6. Alarm output: When the EEPROM is detected that has a mistake or the ON-
TIME attention is effective at switching the TV. The CPU pin3 can output the pulse of
1K. If this signal is mixed with the power, then the sound of the du , du are
heard .
7. Y/C control: If the option of COMB.FILTER is set to 1 at "SETUP mode,
then the Y/C separation control function is selected, the CPU pin42 is used as the
output of Y/C separation control.
Port COMB.FILTER ON COMB.FILTER OFF
Pin42 0 1
8. SRS control function: The CPU pin35 is used as the SRS control function
output.
Port SRS ON SRS OFFPin35 1 0
9. Noise rejection function: CPU Pin37 (MUTE) and Pin41(V-MUTE) are used as
the noise rejection control output.
a). POWER ON/OFF
POWER OFF POWER ON POWER OFF
POWER OUT:H L H
MUTE OUT:
H L H
b). Besides the POWER ON/ OFF, the MUTE output port is controlled when the internal
MUTE is effective. The differentiation of Pin37 (MUTE) and Pin41 (V- MUTE) is: the
7
8/6/2019 Sanyo Service Manual
8/43
Pin37 (MUTE) can control the MUTE at all circumstance, but the Pin41 (V-MUTE)
