Ronda 8040 N Complete Technical Documentation

RONDA mastertech 8000

XXL Chronographs,

Retrograde and Big Date

Caliber 8040.N 15'''

Product Specifications

Analog quartz movement

Line mastertech

Caliber 8040.N

Size 15'''

Version Swiss Made 13 Jewels / gold plated

Standard battery life 48 months

Hand fitting height 1

Features

Repairable metal watch movement

Very long battery life

Power saving mechanism with pullled out stem: Reduction

of consumption approximately 70%

Very easy handling by two pushers

Big date with quick change

Date: 07.04.2015 www.ronda.ch Page: 1

RONDA mastertech Caliber 8040.N 15'''

Functions

3 eyes

Chronograph

Center stop second (1/1

sec)

1/10 seconds up to 30

minutes

30 minute counter

10 hour counter

ADD and SPLIT functions

Day Retrograde

Big date

Small second

Technical Specifications

Diameter Total 34.60 mm

Case fitting 33.80 mm

Movement height 5.60 mm

Height over standard battery 5.60 mm

Movement rest 0.60 mm

Height over stem 3.30 mm

Length of stem travel 1.00 mm

Stem thread 0.90 mm

Standard battery 395

Standard battery life 48 months

Battery voltage 1.5 V

Current consumption typical 1.48 A (Date

Mechanism not in

Gear)

Current consumption maximum 2 A (Date

Mechanism not in

Gear)

Useful torque second typical 6 Nm

Useful torque minute typical 300 Nm

Useful torque center stop second typical 7 Nm

Operating temperature 0 - 50 C

Instantaneous rate -10/ +20 sec/month

Resistance to magnetic fields 18.8 Oe

Resistance against shock NIHS 91-10

Date: 07.04.2015 www.ronda.ch Page: 2

Scurit entre l'aiguille des seconde et le verreSicherheit zwischen Sekundenzeiger und GlasSecurity between second hand and glass

: min 0.50 mm: min 0.50 mm

: min 0.50 mm

Poussoirs / Drcker / Pushers

courseWeg 1.30way

Position pousseGedrckte Stellung R 16.20 50Pushed in

+200-0

3.3

+

70 0

1.

4 20

0

1.8

10

6.5

14.14

1.41

16.22

13.06

Position zum entfernen der StellwellePosition to remove the stem

Position pour extraire la tige

PileBatterie 395 9.50 x 2.70Battery

S 0.

9Co

urs

e / W

eg

/ Tra

vel :

1.

00

S 0.

9

30

30

S 0.9

1

9.72

S 0

.9

6.68

14.85

5.6

2.8

min

5.

85

min

3.

05

3.3

+ 15

00

-

+ 70

0

0.00 - 0.15

0.00 - 0.22 34.6

+0 -30

1

.1

33.8 +0 -300.

6 10

Vis / Schraube / Screw No. : 4000.323 Vis / Schraube / Screw No. : 4000.324(R 16.28 3x)

0.43

2.1

0.3

0.8

1.2

3.95

(R 16.28 3x)

0.28

2.6

0.3

1.2

00No. 5000.3678040.N

Sous rserve de modificationsAenderungen vorbehalten

Modifications reserved

FrameUhrwerkgestellCage

RONDA

15'''

16 Mai 2008

Modified

Scale 10 : 1 (5 : 1) (A3H)+/- 20 m

mgIssued

ToleranceReleased

12 Feb 2010flA 5198

Yes

30

b

De

Dt

T

P

1

.4 200

Dp

Dp

30

b

Dp

0

a b

T

P

Dt

De

a

b

1.

6 0-10

0

D

p

0.

4

30 2

Dp

20

a b

T

P

Dt

De

a

b

0

.4

10 2

1

.6 0-100

Dp

20

Dp

15

a b

T

P

Dt

De

0.4

15 2

1

.6 0-100

Dp

a

b

15

Dp a b

10

T

Dt

De

P

1

.6 0-100

Dp

0

.4

20 2a

b

10

00No. 5000.3908xxx.x



Angle of pusher A and BWinkel der Drcker A und BAngle des poussoirs A et B

RONDA

Modified

Scale 2.5 : 1 (10 : 1) (A3H)+/- 20 m

flIssued

ToleranceReleased

12 Feb 2010flA 5198

YES

22 Sep 2009

0.5 max.

0.250 0.900 +6 -4

1.500 +4 -2

0.7 0.5 max.

GE

F

Ajustement aiguille des heuresStundenzeigerpassungHour hand fitting

CylindriqueZylindrischCylindrical

Ajustement aiguille des minutesMinutenzeigerpassungMinute hand fitting

Petite secondeKleine SekundeSmall second

Aiguille des joursTageszeiger

Day hand

J

Compteur 1 aiguille1 Zeiger Zhler1 Hand counter

Ajustement aiguille des secondes chronoStopp-SekundenzeigerpassungChrono second hand fitting

Heures / minutes / secondes chronoStunden / Minuten / Stopp-Sekunden

Hours / minutes / chrono seconds

02No. 3316.1228040.N



Hand fitting heightsZeigerwerkhhenAiguillages

RONDA

15 '''

02 Jun 2008

Modified

Scale 20 : 1 (A3H)m

mgIssued

ToleranceYesReleased

Masse / Masse / weight

A ig .

d e

s s e

c .

c hr o

no

S to

p p-

S ek u

nd e

nz e

i ge

r

C hr o

no

s e

c on

d h a

nd

A ig u

i l l e

c om

p te

ur

mi n

ut e

Z h l

er

Z ei g

er

Mi n

ut e

C ou

nt e

r h a

nd

mi n

ut e

Balourd / Unwucht / unbalance0.06

A ig .

p e

t i te

s e

c on

d es

K le

i ne

S e

k un

d en

z ei g

er

S ma

l l s e

c on

d h a

nd

A ig .

d e

s m

i nu

t es

Mi n

ut e

nz e

i ge

r

Mi n

ut e

h a

nd

A ig .

d e

s h e

ur e

s

S tu

nd e

nz e

i ge

r

Ho

ur

h an

d

Inertie / Massentrgheit / InertiaForce de chassage / Aufpresskraft / Force

0.80

40

30

0.80

10

0.07

10

0.03

40 30 30

gmm 2Nm

mg

N

--- ---

max.

max.

max.

max.

A ig .

d e

s j o u

r s

r t r o

g ra

d eT a

g es a

nz e

i ge

r r e

t r og r

ad

Da

y h a

nd

r et r o

g ra

d e Lors de la pose d'aiguilles, le mouvementdoit tre soutenu.Beim Zeigersetzen muss das Werkabgesttzt werden.The movement needs to be supportedfor hand setting.

A ig u

i l l e

c om

p te

ur

1 /1 0

s e

c .

Z h l

er

Z ei g

er

1 /1 0

S e

k .C o

un

t er

h an

d 1 /

1 0

s ec .

0.02

30

10

30

30 10 10

0.40

1.0

30

1.01.00.41.0

0.200

Ajustement aiguilleZeigerpassungHand fitting

Appui cadranZifferblattauflageDial seat

ConicitKonizittConicity2%

* En cas de donnes diffrentes, veuillez contacter le service aprs-vente * Bei abweichenden Werten, bitte technischen Kundendienst anfragen * In case of different values, please contact the customer service

S ou

s l ' a

i gu

i l le

d e

s j o u

r s

r t r o

g ra

d eU n

t er

T ag e

s ze

i ge

r r e

t r og r

ad

U nd e

r D

ay

h an

d r e

t r og r

ad e

S ou

s l ' a

i gu

i l le

d e

s s e

c on

d es

c hr o

no

U nt e

r

S to

p p-

S ek u

nd e

nz e

i ge

rU n

d er

c hr o

no

s e

c on

d h a

nd

S ou

s l ' a

i gu

i l le

d e

p e

t i te

s e

c on

d eU n

t er

k l

ei n

e

S ek u

nd e

nz e

i ge

rU n

d er

s ma

l l s e

c on

d h a

nd

S ou

s l ' a

i gu

i l le

c o

mp t

eu

r 1

ai g

ui l l

eU n

t er

Z e

i ge

r 1

Z ei g

er

Z h l

er

U nd e

r h a

nd

1 h a

nd

c ou

nt e

r

1.101.55

S ou

s l ' a

i gu

i l le

d e

s h e

ur e

sU n

t er

S t

un

d en

z ei g

er

U nd e

r h o

ur

h an

d

S ou

s l ' a

i gu

i l le

d e

s m

i nu

t es

U nt e

r

Mi n

ut e

nz e

i ge

rU n

d er

mi n

ut e

h a

nd

Peinture comprise / inkl. Farbe / Paint includedEpaisseur maximum du cadran

Maximale ZifferblattdickeMaximum dial thickness

0.552.10 0.550.55

E pa

i ss e

ur

d es

ai g

ui l l

es

Z ei g

er d

i ck e

Ha

nd s

t h

i ck n

es s

0.15

AiguillagesZeigerwerkhhe

Hand fitting height

No

1

-

P et i t

e

s ec o

nd e

K le

i ne

S e

k un

d eS m

al l

s ec o

nd

P ig n

on

c o

mp t

eu

rZ

h le

r t ri e

bC o

un

t er

p in

i on

J J

P ig n

on

d e

s s e

c on

d es

c hr o

no

S to

p p-

S ek u

nd e

nt r i

eb

C hr o

no

s e

c on

d p i

ni o

n

C ha

us s

eM

i nu

t en

r oh r

C an

no

n-

p in

i on

Ro

ue

d e

s h e

ur e

sS t

un

d en

r ad

Ho

ur

wh e

el

Dpassement Hhe ber Zifferblattauflage

Height over dial seat

2.61

G

1.95 1.521

AiguillagesZeigerwerkhhe

Hand fitting height

E FNo H

1.15

-

1.00 1.00 1.00

J

P ig n

on

d e

s j o u

r s

r t r o

g ra

d eT a

g es a

nz e

i ge

t r ie

b r e

t r og r

ad

Da

y p i

ni o

n

r et r o

g ra

d e1

ai g

.

1 Z e

i ge

r1

Ha

nd

N

1.05

J

0 .3 5

ConicitKonizittConicity2%

0 .3J

+6 -4 0.206

0 .3

0 .3

+6 -4 0.206

Ajustement aiguilleZeigerpassungHand fitting

HConicitKonizittConicity2%

0 .3

0.256 +6-4

0.5 max.

0.200

15 Okt 2014 dhA 13275

N N

RONDA 8040.B, 8040.N

Tige (dimensions / forces)Stellwelle (Dimensionen / Krfte)Stem (dimensions / forces)

Issued

---

Scale

Tolerance

10:1 (A3)

00

07 Sep 2012

No.

ds5222



5030.023

Modified

Released YES

---

A 11741ds5222

L2

L

S

L1L3

No. d'articleArtikelnummerPart number

L L1

3000.203.CO

L2 L3 S DCouleur de la couronneKronenfarbeCrown color

21.30 11.67 28.57 11.12 1.100.90

gris fonc

UN 7005

Tige de travail (intgre dans le mouvement)Arbeitstellwelle (im Werk eingebaut)Working stem (implemented in the movement)

Code

dunkelgraudark grey


L L1

3000.203

L2 L3 S D

21.30 11.67 28.57 11.12 1.100.90

Tige (normale) / Stellwelle (normal) / Stem (normal)


L4 L5(min)

3000.040

L6 S1 S2 D1

12.00 1.90 2.45 0.90 1.350.90

Rallonge de tige / Stellwelle Verlngerung / Stem extension S2

L4

L5

S1 D1

d'encageage / Gehusepassungs- / Case fitting

Bote / Gehuse / Case

0.02 - 0.10

Couronne normaleNormale KroneNormal crown

D

L6

Force min.Kraft min.Force min.

10 N

Force max.Kraft max.Force max.

15 N

Couronne visseGeschraubte KroneScrewed crown

DOMVT096e T2 Information

Version: 1.1

Prozess: 3.1.3

Casing instructions RONDA mastertech 8040.N nd. Dat:30.04.2010

5331 (RONDA WEB PAGE)

Ersteller: fb5163 Geprft: hh5160 Freigabe IQ Soft: ah5256 / ea5250

Information & references Case & pushers Frame drawing Dial, positions of counters & day Dial drawing Hand fitting heights & specifications for hands Hand fitting heights drawing Adjustment of functions Users manual

Dial & hand setting 1. Note the by the working hand indicated day (example: 2 = TUE = Tuesday) 2. Remove working hands 3. Set dial 4. Set WEEKDAY hand to the same day (example: 2 = TUE = Tuesday)

or

1. Stem in position 3: Turn crown forwards until weekday hand has jumped back to Position 1

2. Remove working hands 3. Set dial 4. Set WEEKDAY hand to Monday

5. Set SECOND hand, HOUR and MINUTE counters to arbitrary index 6. Stem in position 2: Turn crown backwards until date 02 is indicated 7. Stem in position 3: Turn crown forwards until date has jumped from 02 to 03 8. Set HOUR and MINUTE hands to 12 oclock 9. Set SECOND counter to arbitrary index

Calendar changing phases & times Date ~ 1 - 2 h Weekday ~ - 2 h after the date change

Initialisation of chronograph hands 10. To ensure proper positioning of the chronograph hands to the zero position, a complete initialisation must be

issued after the hand setting operation is completed. Viz.: Each counter must be adjusted 1x to the zero position. 11. End: Push stem back in position 1.

Movement holder

Remark During the date setting with quick mode (stem in position 2), the speed may not exceed 5 days / second.

Pull out stem in position 3

Keep pushers A & B depressed for at least 2 seconds

Adjust the counter to the zero position by activating pusher A

Press pusher B one time Change to the next counter

A Hand setting T Stem removal Part number H 80XX.1A4 Part number H 80XX.1T

The movement needs to be supported for hand setting.

Maximal force: Hour & minute hands: max. 40N All other hands: max. 30N

For removal of the stem, the stem must be pushed into position 1 (pressed in) prior to apply pressure to the setting lever.

Information re BIG DATE An extreme acceleration in setting the date with quick mode (BIG DATE) can induce a false date indication. The synchronization is re-established by setting the date from 01 till 31 (stem in position 2).

A

B

1 2 3

Wichtig! Die Hhe der Absttzschrauben muss vor Beginn jeder Serie eingestellt werden. Important! Veuillez ajuster lhauteur des vis de support au pralable de chaque srie. Important! Adjust height of support screws prior to each series.

Erstellt: fb5163 Geprft: hh5160 Freigabe IQ-Soft: ah5256 / ea5250 Seite 1/8

Werkhalter T2 Porte-pice T2

Movement holder T2

DOMVT004

Version: 1.9

Verwendung & bersicht Utilisation & Vue densemble

Utilisation & Overview

Prozess: 3.1.3

nd.-Dat.: 04.04.2014 5110, 5112, 5150, 5151, 5152, 5160, 5161, 5163, 5164, 5166, 5310, 5311, 5312, RTC, RHK Ermano, Pine Precision AF Switzerland SA, Horotec SA, Tschudin & Schneider

A Zeiger setzen

T Stellwelle entfernen Diverses

Poser les aiguilles Enlever la tige Divers

Hand setting Stem removal Various

Kalibergruppe Artikelnummer

Artikelnummer

Artikelnummer Groupe de calibre Numro darticle Numro darticle Numro darticle Calibre group Part number Part number Part number

Z60 H ZXX.1A H ZXX.1T

Z60

8000-8499 H 80XX.1A H 80XX.1T

8040.B 8040.N

7000-7999 H 7XXX.1A H 7XXX.1T

700X.B 700X.L 700X.N 700X.P


DOMVT004 / Version: 1.9 / Prozess: 3.1.3 / nd.-Dat.: 04.04.2014 Seite 2/8

A Zeiger setzen

T Stellwelle entfernen

P Alarm-Check

Poser les aiguilles Enlever la tige Contrle dalarme

Hand setting Stem removal Alarm check


Artikelnummer


6000-6999 H 6XXX.1A H 6XXX.1T

6XXX.B 6XXX.D

Swiss Made Swiss Parts

4000-5999.B/.C/.D/.E H 5XXX.1A H 5XXX.1T H 5XXX.1P

4XXX.B 5XXX.B 5XXX.C 5XXX.D 5XXX.E

4000-5999.F H 5XXX.FA H 5XXX.1T H 5XXX.1P

5XXX.F (4XXX.B) (5XXX.B) (5XXX.C) (5XXX.D) (5XXX.E)



A Zeiger setzen





Artikelnummer


3500-3999 H 35XX.1A H 35XX.1T

3520.D 3540.D

1062-1069 H 106X.1A H 106X.1T

1062 1063 1064 1069


6h

6h

1062

- - - -

1063

-

-

1064

-

-

1069

- - - -

1042 H 1042.1A H 1042.1T

1042



A Zeiger setzen





Artikelnummer


1032 H 1032.1A H 1032.1T

1032

1012-1019 H 101X.1A H 101X.1T

1012 1013 1014 1015 1016 1019

1002-1009 H 100X.1A H 100X.1T

1002 1003 1004 1005 1006 1009



A Zeiger setzen





Artikelnummer


782-788 H 78X.1A H 78X.1T

782 783 784 785 788


772-775 H 77X.1A H 77X.1T

772 773 774 775




A Zeiger setzen





Artikelnummer


762-763 H 76X.1A H 76X.1T

762 762E 763 763E


762

- -

762E

- -

763

-

763E

751-753 H 75X.1A H 75X.1T

751 753


751

- -

753



A Zeiger setzen





Artikelnummer


712-715 H 71X.1A H 71X.1T

712 713 714 715


702-708 H 70X.1A H 70X.1T

702 703 704 705 708 (706)


706 H 706.1A H 70X.1T

706.1 706.2 706.3 706.B


6h

6h



A Zeiger setzen





Artikelnummer


582-585 H 58X.1A H 58X.1T

582 583 585

512-519 H 51X.1A H 51X.1T

512 513 515 517 519

502-509 H 50X.1A H 50X.1T

502 503 505 507 509

MON

TUE W

ED THU FRI SAT SUN

15

60

30

45

2 3

30

1020

10 123

456789

MON

TUE W

ED THU FRI SAT SUN

15

60

30

45

2 3

30

1020

10 123

456789

MON

TUE W

ED THU FRI SAT SUN

15

60

30

45

2 3

30

1020

10 123

456789

MON

TUE W

ED THU FRI SAT SUN

15

60

30

45

2 3

30

1020

10 123

456789

MON

TUE W

ED THU FRI SAT SUN

15

60

30

45

2 3

30

1020

10 123

456789

MON

TUE W

ED THU FRI SAT SUN

15

60

30

45

2 3

30

1020

10 123

456789

MON

TUE W

ED THU FRI SAT SUN

15

60

30

45

2 3

30

1020

10 123

456789

I II III

MON

TUE W

ED THU FRI SAT SUN

15

60

30

45

2 3

30

1020

10 123

456789

I II III

MON

TUE W

ED THU FRI SAT SUN

15

60

30

45

2 3

30

1020

10 123

456789

I II III

MON

TUE W

ED THU FRI SAT SUN

15

60

30

45

2 3

30

1020

10 123

456789

III65,5% = 40mm Druchmesser

III

A

65,5% = 40mm Druchmesser

III

B


III

A


IIII II


III

B


III

A

MON

TUE W

ED THU FRI SAT SUN

15

60

30

45

2 3

30

1020

10 123

456789

I II III

MON

TUE W

ED THU FRI SAT SUN

15

60

30

45

2 3

30

1020

10 123

456789

I II III

MON

TUE W

ED THU FRI SAT SUN

15

60

30

45

1 7

30

1020

10 123

456789

II IIII

MON

TUE W

ED THU FRI SAT SUN

15

60

30

45

2 2

30

1020

10 123

456789

I II III

MON

TUE W

ED THU FRI SAT SUN

15

60

30

45

0 1

30

1020

10 123

456789

I II

MON

TUE W

ED THU FRI SAT SUN

15

60

30

45

3 1

30

1020

10 123

456789

I II

MON

TUE W

ED THU FRI SAT SUN

15

60

30

45

2 3

30

1020

10 123

456789

15

60

30

45

2 3

30

1020

10 123

456789

Display elements 8040.N

Minute hand110 second counter (houer counter after 30 minutes)

Day of the week handHour handMinute counterSecond counterSecond handDate

Chronograph: Basic function(Start / Stop / Reset)

Example: Start: Press push-button A.

Stop: to stop the timing, press push-button A once more and read the chronograph counters:

4 min / 38 sec / 710 sec

Zero positioning: Press push-button B. (The chronograph hands will be reset to

their zero positions.)

Chronograph: Accumulated timingExample: Start: (start timing)

Stop: (e.g. 15 min 5 sec following )

Restart: (timing is resumed)

* Stop: (e.g. 5 min 12 sec following ) = 20 min 17 sec (The accumulated measured time is shown)

Reset: The chronograph hands are returned to

their zero positions.

Please note:* Following , the accumulation of the

timing can be continued by pressing push-button A (Restart / Stop, Restart / Stop, ).

Chronograph: Intermediate or interval timingExample: Start: (start timing) Display interval: e.g. 20 minutes 17 seconds (timing

continues in the background) Making up the measured time: (the chronograph hands are quickly

advanced to the ongoing measured time.) Stop: (Final time is displayed) Reset: The chronograph hands are returned to

their zero position.

Please note: * Following , further intervals or inter-

mediates can be displayed by pressing push-button B (display interval / make up measured time, ...).

*

Adjusting the chronograph hands to zero positionExample: One or several chronograph hands are not in their correct zero positions and have to be adjusted (e.g. following a battery change).

Pull out the crown to position III (all chronograph hands are in their correct or incorrect zero position.)

Keep push-buttons A and B depressed simultaneously for at least 2 seconds (the second counter hand rotates by 360 corrective mode is activated.)

Adjusting the second counter handSingle step


III

A 1 x shortContinuous


III

A long

Adjusting the next hand B


III

Adjusting the 110 second counter hand (position 3h)Single step


III



III

A long

Adjusting the next hand B


III

Adjusting the minute counter hand (position 9h)Single step


III



III

A long

Returning the crown to position I

Termination of the chronograph hands adjustment (can be carried out at any time).

Setting the time

*Pull out the crown to position III (the watch stops).

Turn the crown until you reach the correct time 8:45.

* Push the crown back into position I.

Please note:* In order to set the time to the exact second, must be pulled out when the second hand is in position 60. Once the hour and minute hands have been set, must be pushed back into position I at the exact second.

Setting the date (quick mode)

Pull out the crown to position II (the watch continues to run).

Turn the crown anticlockwise until the correct date 01 appears.

Push the crown back into position I.

Please note:During the date changing phase between approx. 8 PM and 12 PM; the date must be set to the date of the following day.

An extreme acceleration in setting the date with quick mode can induce a false date indi-cation. The synchronization is re-established by setting the date from 01 till 31 (crown in position II).

Setting the date, day of the week (8040.N), time

Example: Date / time on the watch: 17 / 01:25 / MON Present date / time: 23 / 20:35 / SAT

Pull out the crown to position III (the watch stops).

Turn the crown until yesterdays day of the week FRI appears.

Push the crown to position II.

Turn the crown anticlockwise until yesterdays date appears 22 .

* Pull out the crown to position III (the watch stops). Turn the crown until the correct date 23 and day of the week SAT appears.

** Continue to turn the crown until the correct time 8:35 PM appears.

Push the crown back into position I.

Please note:* To set your watch to the exact second,

please refer to the chapter entitled setting the time.

** Please observe the AM/PM clock rhythm.

Users Manual English

RONDA mastertech Movement Cal. 8040.N & 8040.B

04 / 2014

Battery type: 395 (diameter 9.5 mm x 2.6 mm / SR 927 SW)Accuracy: +20 / -10 seconds per month

Display elements 8040.B

Minute hand110 second counter (houer counter after 30 minutes)

Date

Hour hand

Minute counter

Second counter

Second hand

Description of the display and control buttons

Control buttons

Push-button A & BCrown

Control buttons

Push-button A & BCrown

B B

A A

You have decided to buy a watch, which was assembled by a watch- maker using a Ronda movement. Please note that no watches are produced or distributed under the Ronda Brand.

In case of repairs, guarantee claims and questions concerning the functioning of a watch, purchasers and consumers should contact their retailer or the watch manufacturer, for which the relevant information can be found in the sales or guarantee documentation provided with the watch.

B

B

B

B

B

B

B

B

B

B

B

B

B

B

B

B

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

01

05

02

06

03

07

04

08

Technical instructions 8040.N

10/2013 V RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 1

2000.700.CO Main plate1.

3406.038 Pusher jumper A2. Put the yellow jumper between the two posts on the closer side.-#13;

3406.030 Pusher jumper B3. Put the grey jumper between the two posts on the further side.

3305.364.CO Canon pinion (Aig.1)4.

A2030.029 Center bridge5. Center bride held by 2 screws 4000.250.

4000.250 Screw6.

3406.040 Friction spring7. Friction spring held by 1 screw 4000.250.

4000.250 Screw8.

3622.055 Stator9.

3622.054 Stator chrono10. Mark |1| on stator.

3715.119.RK Rotor11.

3715.119.RK Rotor12.

B

3147.073.CO Intermediate wheel13.

3147.074.CO Intermediate wheel chrono14.

3122.067.CO Third wheel15.

3136.180.CO Chronograph wheel16.

3136.179.CO Second wheel17.

3136.178.CO Small second wheel18.

3004.203.CO Reverse wheel19.

C



2020.188.G Train wheel bridge20. Train wheel bridge held by 2 screws 4000.250. Mark |2|.

4000.250 Screw21.

3622.039 Stator counter (cpt 6h and 9h and chrono)22.

3402.012.CO Minute counting wheel23.

3715.120.RK Rotor24.

3147.076.CO Intermediate wheel (counter 30min)25.

D

2020.191.G Counter train wheel Bridge26. Train wheel bridge held by 2 screws 40000.250. Mark |2|.

4000.250 Screw27.

3622.039 Stator counter28.

3402.013.CO Counting wheel (1/10 s)29.

3715.120.RK Rotor30.

3147.075.CO Intermediate wheel (counter 1/10 s)31.

2020.190.G Counter train wheel bridge32. Train wheel bridge held by 2 screws 40000.250. Mark |2|.

4000.250 Screw33.

E

3016.029 Stop lever34. Stop lever held by 1 screw 4000.249.

4000.249 Screw35.

2130.222 Maintaining plate36. Maintaining plate held by 1 screw 4000.248.

4000.248 Screw37.

F



3621.072.RK Coil centre38. Attention: Please hold the coil only on the grey coil core.

3621.055.RK Coil counter39. Attention: Please hold the coil only on the grey coil core.



4000.250 Screw42.G

3603.089 Battery insulator43.

3601.134 Pusher contact spring44.

3612.218 Electronic module45. Electronic module held by 6 screws. (Electronic measurements may berealised now.)

4000.248 Screw46. 4 screws 4000.248 for pressing the module on the coils.

4000.250 Screw47. 2 screws 4000.248 for pressing the module on the 2 posts.

3601.132.G Lateral bridle48. Lateral bridle held by 1 screw 4000.250.

4000.250 Screw49.

H

3603.090 Circuit insulator50.

2130.206.G.M01.8040N Electronic module cover51. Electronic module cover held by 4 screws 4000.250.

4000.250 Screw52.

3600.010.HGF Battery 39553.

3601.133.G Bridle +54. Bridle + held by 2 screws 4000.250.

4000.250 Screw55.

I




J

3017.054.CO Setting lever57.

3001.046 Sliding pinion58.

3015.088 Yoke (3 positions)59.

3905.063 Setting lever jumper60. Lever held by 1 screw 4000.282.

4000.282 Screw61.

K

3004.200 Corrector setting wheel62.


3015.087.CO Setting wheel yoke64.

L



2130.208 Setting mecanism cover65. Setting meca cover held by 4 screws 4000.305.

4000.305 Screw66.

3000.203.CO Setting stem67.

3004.222 Intermediate setting wheel68.

3007.079.CO Minute wheel69.

2130.209 Minute train bridge70. Minute train bridge held by 3 screws 4000.278.

4000.278 Screw71.

M

2000.672.G Main plate retro72. Minute plate retro held by 4 screws 4000.248.

4000.248 Screw73.

N3004.220 Tens indicator driving wheel74. The short tooth of the tens indicator driving wheel must point to thecenter of the movement.

3500.072 Tens jumper75.

2130.187 Tens jumper maintaining plate76. Tens jumper maintaining plate held by 2 screws 4000.279. Tensioningthe spring arm.

4000.279 Screw77.

3301.292.CO Hour wheel78.

3004.208.CO Date indicator driving wheel79.

3147.061 Intermediate date wheel80.

O



3404.006.CO Day cam81. Place parts as shown on graphics.

3406.032 Day rack82.

3406.031 Day rack lever83.

3147.066.CO Date corrector setting wheel84.

3507.059.CO Date corrector wheel85.P

2130.191 Date indicator plate86.

3905.068 Date corrector spring87. Date corrector spring held by 1 screw 4000.244.

4000.244 Screw88.

3905.066 Day rack lever spring89. Tensioning the spring arm.

3500.068 Date jumper90.

3500.069 Day jumper91. Tensioning the spring arm.

Q



3504.234.AD.1.A Units indicator (standard)92. Nick of the indicator at 3 o`clock.

2130.192 Date indicator maintaining plate93. Date indicator maintaining plate held by 1 screw.

4000.250 Screw94.

3905.064 Date jumper spring95. Insert the date jumper spring in the previous opening.

3004.244 Day finger96. Stem pos III: Turn crown forwards until the date jumps. Stem pos II:Move the date until the nick is at 3 o`clock. Position the end of the

teeth against the day came pinion while turning softly incounterclockwise direction.

3004.212 Days driving wheel97. Insert the tooth of the wheel in the flange gap, while turning softly incounterclockwise direction to ensure correct position of the day finger.

3401.086.FI Day indicator pinion98.

3147.062 Tens intermediate wheel99. Arrow positioning radially outwards.

3504.231.AD.1.A Tens indicator (standard)100. Nick of the indicator at 3 o`clock.

3315.003 Friction spring101.

2130.193.G Date mecanism maintaining plate102. Date maca maintaining plate held by 3 screws 4000.320.

4000.320 Screw103.

3506.077.G Intermediate Dial support104. Polished version first.

3506.076.G Dial support105.

8200 Moebius 8200106.

9014 Moebius 9014107.

124 Jismaa 124108.

9020 Moebius 9020109.

R

S

10/2013 RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] EM 1

Electronic measurements

8040.N

Battery 395

Voltage 1.55 V

Setting stem in position I, calendar not in gear, 60 s measuring interval for rate and consumption:

Typical consumption Maximal consumption

1.48 A 2.00 A

Rate -10s/M. .. +20s/M.

Lower working voltage limit 1.20 V

Hold down the electrical module to allow the electronic flow.

Setting stem in position III, 60 s measuring interval:


0.10 A 0.30 A



8040.N

Coil resistance M1 1.50 k .. 1.70 k




Coil isolation M1/M2/M3/M4 k

Signal generator (4.9 ms, 8 Hz):

Lower working voltage limit M2/M3/M4 1.20 V


10/2013 M RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected] 1


3406.038 Pusher jumper A2. Put the yellow jumper between the two posts on the closer side.

3406.030 Pusher jumper B3. Put the grey jumper between the two posts on the further side.

3305.364.CO Canon pinion (Aig.1)4.

A2030.029 Center bridge5. Center bride held by 2 screws 4000.250.

4000.250 Screw6.

3406.040 Friction spring7. Friction spring held by 1 screw 4000.250.

4000.250 Screw8.

3622.055 Stator9.

3622.054 Stator chrono10. Mark |1| on stator.

3715.119.RK Rotor11.

3715.119.RK Rotor12.

B

3147.073.CO Intermediate wheel13.

3147.074.CO Intermediate wheel chrono14.

3122.067.CO Third wheel15.

3136.180.CO Chronograph wheel16.

3136.179.CO Second wheel17.

3136.178.CO Small second wheel18.

3004.203.CO Reverse wheel19.

C



2020.188.G Train wheel bridge20. Train wheel bridge held by 2 screws 4000.250.

4000.250 Screw21.

3622.039 Stator counter (cpt 6h and 9h and chrono)22.

3402.012.CO Minute counting wheel (30min)23.

3715.120.RK Rotor24.

3147.076.CO Intermediate wheel (counter 30min)25.

D

2020.191.G Counter train wheel Bridge (2h30)26. Train wheel bridge held by 2 screws 40000.250. Mark |2|.

4000.250 Screw27.

3622.039 Stator counter28.

3402.013.CO Counting wheel (1/10 s)29.

3715.120.RK Rotor30.

3147.075.CO Intermediate wheel (counter 1/10 s)31.

2020.190.G Counter train wheel bridge32. Train wheel bridge held by 2 screws 40000.250. Mark |1|.

4000.250 Screw33.

E

3016.029 Stop lever34. Stop lever held by 1 screw 4000.249.

4000.249 Screw35.

2130.222 Maintaining plate36. Maintaining plate held by 1 screw 4000.248.

4000.248 Screw37.

F



3621.072.RK Coil centre38. Attention: Please hold the coil only on the grey coil core.




4000.250 Screw42.G

3603.089 Battery insulator43.

3601.134 Pusher contact spring44.

3612.218 Electronic module45. Electronic module held by 6 screws.

4000.248 Screw46. 4 screws 4000.248 for pressing the module on the coils.

4000.250 Screw47. 2 screws 4000.248 for pressing the module on the 2 posts.

3601.132.G Lateral bridle48. Lateral bridle held by 1 screw 4000.250.

4000.250 Screw49.

H

3603.090 Circuit insulator50.

2130.206.G.M01.8040N Electronic module cover51. Electronic module cover held by 4 screws 4000.250.

4000.250 Screw52.

3600.010.HGF Battery 39553.

3601.133.G Bridle +54. Bridle + held by 2 screws 4000.250.

4000.250 Screw55.

I



2000.700.CO Main plate56. .

J

3017.054.CO Setting lever57.

3001.046 Sliding pinion58.

3015.088 Yoke (3 positions)59.

3905.063 Setting lever jumper60. Lever held by 1 screw 4000.282.

4000.282 Screw61.

K



3015.087.CO Setting wheel yoke64.

L



2130.208 Setting mecanism cover65. Setting meca cover held by 4 screws 4000.305.

4000.305 Screw66.

3000.203.CO Setting stem67.

3004.222 Intermediate setting wheel68.

3007.079.CO Minute wheel69.

2130.209 Minute train bridge70. Minute train bridge held by 3 screws 4000.278.

4000.278 Screw71.

M

2000.672.G Main plate retro72. Minute plate retro held by 4 screws 4000.248.

4000.248 Screw73.

N3004.220 Tens indicator driving wheel74. The short tooth of the tens indicator driving wheel must point to thecenter of the movement.

3500.072 Tens jumper75.

2130.187 Tens jumper maintaining plate76. Tens jumper maintaining plate held by 2 screws 4000.279. Tensioningthe spring arm.

4000.279 Screw77.

3301.292.CO Hour wheel78.

3004.208.CO Date indicator driving wheel79.

3147.061 Intermediate date wheel80.

O



3404.006.CO Day cam81. Place parts as shown on graphics.

3406.032 Day rack82.

3406.031 Day rack lever83.

3147.066.CO Date corrector setting wheel84.

3507.059.CO Date corrector wheel85.P

2130.191 Date indicator plate86.

3905.068 Date corrector spring87. Date corrector spring held by 1 screw 4000.244.

4000.244 Screw88.

3905.066 Day rack lever spring89. Tensioning the spring arm.

3500.068 Date jumper90.

3500.069 Day jumper91. Tensioning the spring arm.

Q



3504.234.AD.1.A Units indicator (standard)92. Nick of the indicator at 3 o`clock.

2130.192 Date indicator maintaining plate93. Date indicator maintaining plate held by 1 screw4000.250.

4000.250 Screw94.

3905.064 Date jumper spring95. Insert the date jumper spring in the previous opening.

3907.047 Day finger flange96. Stem pos III: Turn crown forwards until the date jumps. Stem pos II:Move the date until the nick is at 3 o`clock.

3004.211 Day finger97. Position the end of the teeth against the day came pinion while turningsoftly in counterclockwise direction.

3004.212 Days driving wheel98. Insert the tooth of the wheel in the flange gap, while turning softly incounterclockwise direction to ensure correct position of the day finger.

3401.086.FI Day indicator pinion99.

3147.062 Tens intermediate wheel100. Arrow positioning radially outwards.

3504.231.AD.1.A Tens indicator (standard)101. Nick of the indicator at 3 o`clock.

3315.003 Friction spring102.

2130.193.G Date mecanism maintaining plate103. Date maca maintaining plate held by 3 screws 4000.320.

4000.320 Screw104.

3506.077.G Intermediate Dial support105. Polished version first.

3506.076.G Dial support106.

8200 Moebius 8200107.

9014 Moebius 9014108.

124 Jismaa 124109.

9020 Moebius 9020110.

R

S



8040.N

Battery 395

Voltage 1.55 V

Setting stem in position I, calendar not in gear, 60 s measuring interval for rate and consumption:


1.48 A 2.00 A

Rate -10s/M. .. +20s/M.

Lower working voltage limit 1.20 V

Hold down the electrical module to allow the electronic flow.

Setting stem in position III, 60 s measuring interval:


0.10 A 0.30 A



8040.N





Coil isolation M1/M2/M3/M4 k

Signal generator (4.9 ms, 8 Hz):

Lower working voltage limit M2/M3/M4 1.20 V

Powered by TCPDF (www.tcpdf.org)

Documents

Ronda 8040 N Complete Technical Documentation