RM2CUnderstanding Connections on

the Robot Control Board (RCB).

In the following slides, The RCB components will be documented in detail so that the intended purpose of each part is understood.

The Black SPDT switch is used to cut on and cut off the power to the board.

THE 1n4004 Diode is used to limit REVERSE CURRENT through the circuit if the voltage is accidently applied in reverse.

The GREY stripe on the DIODE is the NEGATIVE side or “CATHODE”. The POSITIVE side of the DIODE is called the ANODE.

The green POWER CONNECTOR is where power is connected to the circuit board. The board should be powered on 12 Volts DC.

You can see in this photo that I marked the power connector with a + and - sign to be sure I

didn’t incorrectly connect power to the

circuit. Be sure to screw the terminals down snug to hold the wire in place. Also, be sure that the

wires are pushed completely into the sockets with NO

insulation showing!

The DISC CAPACITORS in the circuit are used to keep the power source stable so that the voltage doesn’t fluctuate greatly when big loads such as servo motors are powered.

The value of these

capacitors is .1 uF.

These are SMALL

capacitor values

designed to handle

high frequency

shifts.

The 5 Volt Regulator steps the voltage from the power source down to 5 volts to power most of the essential motors, sensors, relays and actuators that are necessary.

The 5 Volt Regulator can handle 5 AMPS of current and so a HEAT SINK is required to help keep the part cool.

The CENTER ROW of all the header pins is connected to the 5 Volt regulator!

5 volt regulatorCenter

Row

Center Row

HEAT

SINK

The 3.3 Volt Regulator powers the Propeller chip and the XBEE Network Controller.

3.3 Volt

The 3.3 Volt Regulator can handle up to 3 AMPS of current and it also requires a HEAT SINK to keep it cool. This regulator gets its power from the 5 volt regulator.

The HEADER PINS are connection points to Pins on the Propeller Chip as well as connections to Positive 5 Volt and Ground.

Each set of three header

pins is organized with the Propeller

Pin Closest to the chip, +5 V in the middle row and Ground in

the outside row.

Propeller PIN

+ 5 Volt

GR

OU

ND

The ULN2803 AMP/DRIVER Is used to pull-up voltage for driving items like stepper motors and relays.

UL

N 2803A

Header Pins are provided

on EACH side of the

ULN2803 A to allow

connections to the chips

INPUT and OUTPUT Pins.

Header Pins

The 5 Volt RELAY is provided to support the control of Solenoids and Pneumatic devices.

A RELAY is an Electromechanical switch that uses a SMALL voltage to control a LARGE

voltage. The use of the relay can allow the user to use the 3.3 v output of the

PROPELLER CHIP to control devices of 12

Volts and higher.

5 Volt Solid State RELAY

The RESISTORS on the circuit board are used to limit the flow of current.

The four 1K RESISTORS shown here are to provide current limiting to pins 12 – 15 where

the PS2 Controller is to be connected.

1k Resisto

rs

The 10K RESISTOR is being used to

provide ISOLATION between the

connection on PIN 12 and POSITIVE Voltage. 10K Resistor

The XBEE WIRELESS NETWORK CONTROLLER is the device which sends the wireless signal from the PS2 controller to the receiver which is on the ROBOT. Generally used to

control signals in a wireless computer network, the XBEE has its own internal software and can be

programmed separate from the Propeller.

The XBEE is directly connected to PIN 4 and PIN 3 on the Propeller Chip. These two pins are affected in Propeller Programming and open the

communication channel between the two XBEE’s.

The YELLOW (RX) and GREEN (TX) LED’S, beside the XBEE,

are used to indicate data transfer.

The PROPELLER CHIP shown below is a MICROCONTROLLER that can be programmed to perform many electronics processes at the same time. Although the CHIP itself is NOT labeled, the sticker below the chip shows the actual PIN connections on the PROPELLER CHIP.

This CHIP is the CORE of the ROBOT CONTROL

BOARD (RCB). This chip enables the operation of all the robotic parts through computer programming.

The Angled FOUR PIN HEADER is used to connect the computer to the PROPELLER through a PROP PLUG.

The PROP PLUG connects to the 4 PIN HEADER with the silver USB connection faced UPWARD (As Shown)

The last part we will discuss is the 24LC256 EEPROM memory chip. Its purpose is to SAVE the programs that you download onto the Propeller chip for reuse , even if you remove power from the board.

This chip is a FLASH MEMORY

device which saves the code

you download to the Propeller

WHEN you use the F11 key!

24LC256 EEPROM