126256

REVEL SCOUT™ MOUNTING BRACKETINSTALLATION AND OPERATING INSTRUCTIONS

The following is intended to provide the basic instructions for installation, operation, and maintenance. Read and understand these operating instructions before use.

Page 2

Product Warnings

• Indicatesahazardoussituationwhich,ifnotavoided,WILLresultindeathorseriousinjury.

• Indicatesahazardoussituationwhich,ifnotavoided,COULDresultindeathorseriousinjury.

• Indicatesapotentiallyhazardoussituationwhich,ifnotavoided,mayresultinminorormoderateinjury.

• Addressespracticesnotrelatedtopersonalinjury.

Read and follow the operating instructions before use.

Mountingfixturemustbesecuredwithhighqualitysteelorstainlesssteel¼inchdiameterboltsbeforeuse.

Revel Scout™ must be secured in the mounting bracket with the supplied rubber strap.

TheRevelScout™mountingbracketmeetsNFPA1901equipmentmountingrequirementsfordrivingorcrewareawhen mounted in accordance with the Revel™ Scout operating instructions.

Installation 1. TheRevelScout™mountingbracketcanbemountedonaverticalorhorizontalsurface.Theviewsbelowgiveacceptableandunacceptable mountingorientationswhichallowthemountingbrackettocomplywithNFPA1901andprovideasafeenvironmentinthecrewarea.

VERTICAL MOUNT VEHICLE FRONT VEHICLE TOP

HORIZONTAL MOUNT VEHICLE FRONT

INVERTED MOUNT-NO ORIENTATIONS PERMISSABLE VEHICLE TOP

2. Position the Revel Scout™ mounting bracket in the desired location to be sure it will fit without interference. 3. Oncepositionedusethebracketasatemplatetomarkthefourmountingholesontheunderlyingsurface. 4. Removethemountingbracketanddrilltherequiredholesfor¼”fasteners. 5. Position the mounting bracket over the drilled holes and fasten the mounting bracket in position with the appropriate fasteners. 6. Figure1providesoveralldimensionsofthemountingbracketandmountingholelocationsasneeded.

Page 03

Figure 1:

13-3/4

15-3/16

4

4-3/4

3-1/2

3X n 9/32

3-1/2

WARRANTY AND DISCLAIMER: We warrant Akron Brass products for a period of five (5) years after purchase against defects in materials or workmanship. Akron Brass will repair or replace product which fails to satisfy this warranty. Repair or replacement shall be at the discretion of Akron Brass. Products must be promptly returned to Akron Brass for warranty service.

We will not be responsible for: wear and tear; any improper installation, use, maintenance or storage; negligence of the owner or user; repair or modification after delivery; damage; failure to follow our instructions or recommendations; or anything else beyond our control. WE MAKE NO WARRANTIES, EXPRESS OR IMPLIED, OTHER THAN THOSE INCLUDED IN THIS WARRANTY STATEMENT, AND WE DISCLAIM ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. Further, we will not be responsible for any consequential, incidental or indirect damages (including, but not limited to, any loss of profits) from any cause whatsoever. No person has authority to change this warranty.

ISO 9001 REGISTERED COMPANY

PHONE: 330.264.5678 or 800.228.1161 I FAX: 330.264.2944 or 800.531.7335 I akronbrass.com

© Akron Brass Company. 2015 All rights reserved. No portion of this can be reproduced without the express written consent of Akron Brass Company.

revised: 05/16

Operating Instructions

1. TheRevelScout™lightmustberotatedtothefulldownpositionasshownbelow. 2. Remove one end of the rubber hold down strap and place the Revel Scout™ in the mounting bracket as shown below. 3. Wraptherubberholddownstraparoundthefootasshownbelowandrefastentheendofthestraptothemountingbracket. 4. The final mounting configuration is shown below.

Rubber hold down strap